Sanyo VHR-690 User manual

Category
Cassette players
Type
User manual
INSTRUCTION MANUAL
Video cassette recorder
VHR=690
G-CODE I!+IQml
PAL NTSC443
Make sure to make these m
settings before operating the
VCR.
CONTENTS
1
PRECAUTIONS
.....................................................
2
CONTROLS .........................................................
3
INTRODUCTION
Remote control batteries insertion ............................ 3
2
CONNECTIONS
.....................................................
4
Accessories ............................................................... 4
PREPARATION
VCR PRESETTING .................................................
5
mml
Adjusting the TV receiver to the video channel ......... 5
-
Tuning control (Auto) ............................................... 5
-
Clock setting . . . . . . . . . . . . . 6
VCR Setup ................................................................. 7
ON-SCREEN MENUS AND BASIC CONTROL ................... 8
3
PLAYBACK ..........................................................
9
Counter memo~ ....................................................... 9
BASICOPERATION
Index search ........................................... .............. . 9
Endless play .............................................................. 9
Variable playback modes ........................ ....... ......... 10
Shuttle dial operation ................................................ 10
Hi-Fi Stereo/Bilingual programmed sound selection 11
Playback of an NTSCtape ......................................... 11
RECORDING TV PROGRAMMED ................................
12
Quick Start Recording timer ...... .............................. 12
4
G-CODE TIMER RECORDING PROGRAMMING ................... 13
On-screen programming ........................................... 13
ON-SCREEN
Programming on the VCR display, ............................ 14
OPERATION
ON-SCREEN TIMER RECORDING PROGRAMMING ........... 15
Confirmation/Cancelling ............................................ 16
RECORDING HISTORY
............................................
16
5
ADVANCED
OPERATION
EDITING
.............................................................
17
Tape copy .................................................................. 17
Audio dubbing ........................................................... 17
6
SPECIFICATIONS
..................................................
18
TROUBLESHOOTING
Back cover
OTHER
. . . . . . .. . .. .. ... ... .. ... ... ... ... ...
PRECAUTIONS
I
Safety precautions
Operating precautions
DANGER:
This VCR contains live parts. Do not remove
the cabinet.
WARNING:
To prevent fire or shock hazard, do not
expose this product to rain or moisture.
CAUTION:
Do not put your hand or other objects in the
cassette loading slot because of the risk of
injury or an accident. Be sure to keep small
children away from the VCR.
Caution concerning condensation
Be careful of condensation
Condensation can form inside a VCR when it
is suddenly moved from a cold place to a
warm, humid one, or when a heater has been
turned on to quickly heat the room.
Do not insert a video cassette if you use
this VCR in areas subject to condensation.
Wait for 1-1/2 to 2 hours to completely
eliminate condensation before using the
VCR.
Place the VCR on a flat, stable, level
surface. Never subject it to violent shaking
or any other shock or impact.
Do not expose the unit to high
temperatures, Excessive heat (heat
sources such as heaters, ovens, closed car
on hot days, etc.) may damage the unit.
Be sure to use this VCR only in a
temperature range of 5SCto 40”C (41 ‘F to
105”F) and at less than 80?’o humidity.
Do not use the unit under the following
conditions:
in locations with high humidity
in presence of excessive dirt or dust
in areas subject to strong vibrations
near strong magnetic fields (e.g.
transmitting antennas, motors,
fluorescent lights, etc.)
Do not stack anything on top of your VCR,
or block the air vents, to prevent damaging
or overheating.
Do not place anything, except VHS video
cassette tapes, in the unit.
Do not allow rain, steam, dew, salt water,
sand, oily smoke, metal objects, etc. to
enter the unit.
Clean with a dry and soft cloth, or soft cloth
slightly moistened with a mild detergent
solution.
Do not use any type of solvent, such as
alcohol or benzine.
Do not forget that even in the power off
state there is an electrical voltage inside the
VCR as long as it is connected to a wall
socket.
Disconnect the power cord from the wall
socket if the VCR is not to be used for a
long time.
INTRODUCTION
Only cassettes marked ~ can
be used with this VCR.
Video cassette recorders bearing
the” F41(Q”mark incorporate
VHS high picture quality
technology. Notethat there is
interchangeability with former
VHSvideo cassetterecorders.
Note:
If the unit does not operate
properly, switch it off, refer to
“TROUBLESHOOTING”or contact
your Sanyo Authorized Service
Centre.
Power onloff
Power is switched on/off by
pressing the POWERbutton
VCRdisplay
Poweron
Rlmml
Poweroff
“Power off’ is the condition in
which only the time is displayed.
2
\
INTRODUCTION
Remote control batteries
insertion
1
2
3
Slide open the lid.
Insert 2 “AA (IECR6)” 1.5
volt batteries (supplied)
according to the@ and @
signs.
Replacethe lid.
UJ
~e
e’
....
Functionindicator
mm
Mode
Playback
Forwardsearct
Doublaspeed
playback
Slowmotion
Fast-forward
Rewind
Reversesearch
Record
Recordpause
Still picture
Frameadvance
Audiodubbing
-
Display
-
I
I
(;;:-:Flashing)
I
i
CONTROLS
Remote control sensor
O~erate the remote control unit within a range of
approx. 30” and approx. 6m (20 ft.) from the-front of
the VCR.
Shuttle
dial
Indication Function Page
CHANNEL+, Programme selection, tracking adjustment during playback
6,11
FF Fast-forward, forward search during playback
9; 10
PAUSEISTILL
Still picture during playback, pause during recording
10, 12
PLAY
Playback
9
POWER
Power onloff
2
REC
Recording
12
REW
Rewind, reverse search during playback
9,
10
STOPIEJECT Tape stop, cassette ejection
9
(On the remote control only)
A-DUB
Audio dubbing
17
AUDIO
Sound track selection
11
CLEAR
Clears data
16
G-CODE
G-Code timer programme set
13
INDEX
Index search
9
INPUT
External input mode selection
17
MEMORY
Counter “0:00:00 position memory
9
MENLVTV
On-screen operation
8
OK Confirms data
6,13
PRESET
Tuner preset
6
RESET
Counter reset
9
SLOW
Slow motion
10
TAPE SPEED Recording tape speed selection
12, 13
x2 Double speed playback
10
o–9
Direct programme selection, for various input
6,12,13
+, Programme selection, tracking adjustment during playback 6,11
CONNECTIONS
Aerial/RF connection
Connect as indicated below.
To a wall socket
+
7
Power cord
AV connection
m
Aerial
q .1
Aerial output cable
Hi-Fi audio connection
If your TV receiver has an AV terminal, the
You can obtain a dynamic sound output
following AV connections are also possible.
through your stereo audio system when you
The advantage of this connection is a
playback a tape recorded in Hi-Fi stereo on
higher quality of picture and sound during
this VCR.
playback.
Stereo sound can only be enjoyed when the
VCR is connected to a stereo monitornv or
stereo audio system using an AV or Hi-Fi
audio connection.
!!f-
.—
Stereo audio system
m
,,[:::3::
_~.T____=
<’
-==7:=
-,
‘.!.,
I
I
1
Audio-cable
Aerial output cable
2
PREPARATION
Accessories
Is everything in the box?
I
Power cord
I
Aerial outputcable
Remotecontrolunit
I
2 “AA (IEC R6)” size,
1.5-volt batteries
Warranty card
2
PREPARATION
K!l
AuTO SETUP
r:rij—
POWER
r
—OK
If you want to recall the AUTO
SETUPscreen,simply press both
CHANNEL(+ and -) buttons on
the VCRfor 3 seconds or more.
e
CHANNEL(+, -)
If in your area, UHFchannel 36
is used by a broadcaster, follow
the steps below.
1
2
3
r
I
I
5
Tune the TV receiverto an
available UHFchannel between
channel 32 and 41 (a UHF
channel not used by aTV
station),
Usinga small screwdriver,
slowly turn the video channel
adjustment screw “RF
CHANNEL”on the backof the
VCR,to the right fora higher
channel than 36 and to the left
for a lower channel than 36.
Adjust the tuning on the TV, if
necessary,so that the
AUTO
SETUP
screen is clear.
RF CHANNEL
i
VCR PRESETTING
After all the connections are completed, please follow steps
- to - before using the VCR.
- W“stiw theTvr-iver tothevideo
channel
_ Tuning control (AUTO)
_ Clock setting
Adiustina the TV receiver to the video
Tuning control (AUTO)
channel -
1 F’ress the POWER button.
z Turn cmycmrTV.
For more details, please refer to your TV
receiver instruction manual.
Note:
If the VCR has been connected to the TV using the
‘(AVconnection”, simply set your TV receiver to the
‘(AV mode and the AUTO SETUP screen will
appear on your TV screen. Go to step 5.
3
4
Auto tuning
This VCR has a built-in tuner capable of
tuning up to 88 TV stations. Each TV station
broadcasting channel is memorized by the
VCR as a programme position number (01
88).
The TV stations available in your area will be
automatically preset in order starting from
programme position number “01”.
Because of this you may have to sort the TV
stations into the correct order. Please refer to
“Sorting the TV stations”.
In case of an “RF connection”, set your
When all available TV stations have been
TV receiver to “VCR” or the position
preset, the function will stop and the TV
designated for VCR use (usually a
station preset to programme position number
position where no TV programme is
“01” will be tuned on your TV screen.
received).
Notes:
For more details, please refer to your TV
receiver instruction manual.
Adjust the tuning on the TV to UHF
channel 36 so that the AUTO SETUP
screen is clear.
TV screen
AUTO SETUP
[OKI +ENTER
[MENUI +TV
This is your video channel.
To view a tape playback or to watch a TV
broadcast tuned on the VCR tuner, set the TV
to the video channel.
b When the AUTO SETUP screen is clear,
press the OK button.
Auto tuning will start.
During the auto tuning operations, please do not
press any of the buttons or controls on the VCR
or remote control.
Auto tuning is not possible if the VCR is set to
AV input mode.
The skip function will be automatically set for all
position numbers where no TV station has been
preset.
Bmlm
Clock setting
ExamP/e: Date,.. 9 December, 1996
Time... 16:15
1 Press the MENUTW button.
2 Set the date and time using the numeric
buttons (O- 9).
Enter in sequence, 0912961615.
\
CLOCK SET
09.12.96
16:15
[+/-] +Tl ME sHIFT
[CLEARI +TO CORRECT
[OKI +ENTER
If you entered a wrong number, press the
CLEAR button to delete it, then enter the
correct number.
For time shifting adjustment, simply press the
(+ or -) button.
3 When finished, press the OK button.
Seconds will start counting from “00 as the
OK button is pressed.
The normal TV broadcast screen will return.
Additional tuning adjustments
Sorting the TV stations
ExamP/e: To change TV1 from programme
position “4 to programme position “1”,
.
q
1 Press the PRESET button.
2 Using the (+ or-) button select the desired
TV station (e.g. TV1).
TV1
3 Using the numeric buttons (O 9), enter the
target programme position number (e.g.
“01”).
4 Press the OK button.
Repeat steps 2 to 4 to change another TV
station programme position number.
5 When finished, press the PRESET button,
Fine tuning
If the tuning is not optimum, it can be
improved by manual fine tuning.
1 Press the PRESET button.
2 Press the FF or REW button to obtain the
best possible picture and sound.
3 Press the OK button.
4 When finished, press the PRESET button.
Skip function
If only programme position numbers 1 to 30
have been preset, set the skip function for
programme position numbers 31 to 88, so that
only the preset TV stations will appear when
pressing the (+ or -) button.
1 Press the PRESET button.
2 Using the numeric buttons or the (+ or -)
button, select the programme position
number to skip.
3 Press the CLEAR button.
The “S” indicator will light,
To cancel the skip function, press the
CLEAR button again to erase the “S” indicator.
4 Press the OK button.
Repeat steps 2 to 4 for every programme
position number to skip.
5 When finished, press the PRESET button.
Manual tuning
This tuning mode can be used to modify the
settings entered by the Auto tuning function,
or to manually preset the TV stations to
particular programme position numbers.
1 Press the PRESET button.
2 Using the (+ or –) button, select the desired
programme position number.
3 Press the PLAY button.
If the search stops on a broadcast other
than the one desired, press the PLAY
button again until the broadcast from the
desired TV station appears on the TV
screen.
4 Press the OK button when the desired TV
station appears on the TV screen.
Repeat steps 2 to 4 to preset another TV
station to another programme position number.
5 When finished, press the PRESET button.
2
PREPARATION
i
REW
E
FF
PLAY
MENLf/TV
Doo
o-9 :::,
CLEAR
‘“’~~ PRESET
Tuning or presetting the
VCRchannels
This is very important for
correct G-Codeoperation.
Ideallyfor simpler operation,
channelsshould bepresetas
follows:
Television Programme
station positionnumber
TV1
1
TV2
2
TV3
3
‘or additional channelsin your
]reait is overto youto selectthe
nest logicalchannelposition to
]Iacethem.
kSky
I’elevision
4
t Canterbury
rv
5
Action TV
6
Whenyou usethe G-Code
function to programme a
recordingfrom a certainchannel
for the first time, it will askyou
theprogramme position number
thatchannelwas presetto, That
settingwill be memorizedand
automaticallysetthe nexttime
thesamechannelis selected.
2
PREPARATION
1
0-9 ;:;
MENU/lV
,0’ ““””
The settings indicated by the “O”
symbols arethe factory default
settings.
Power interruption
If the power to the VCRhas failed
or has beendisconnected for
more than 1 hour, the VCR
display shows ”-: --”.
However,the tuner preset
memory and the VCRSetup
memory will not be erased. So
there is no needto retune the
VCRstations,
The date, time and recording
information regarding future
recordings should be reset,
First refer to”- Clock
setting” on page6, to set the
clock (date and time), then, the
timer recording programmed
should be set again as desired.
7
VCR PRESETTING
VCR Setu~
The VCR Setup is done using the VCR SETUP menu,
1
2
3
Press the MENU~V button.
MENU
1. T I MER PROGRAM SET
2. PROGRAM CHECK I CLEAR
3. VCR SETUP
4. CLOCK SET
Press the numeric 3 button.
0. AUTO TUNING MEMORY
1. NICAM
OAUTO OFF
2 .NTSC PBOPAL-TV NTSC443
3. CH I LD LOCK
ON OOFF
Each item to setuD is selected bv Dressina the Corresuondincl numeric button. To set a different
mode, press repeatedly the num”e’ric butt& corresponding t;the item to set, until the symbol
“O” is displayed to the left of the desired setting.
.-.—..%..
Note:
Be careful not to press the numeric button Oif you do not wish to reprogrammedall programme positions,
If the numeric Obutton is pressed .....
O. AUTO TUNING MEMORY
Auto tuning
The Auto tuning function will start, and all programme
positions will be automatically reprogrammed.
if the numeric 1 button is pressed .....
1. NICAM
NICAM broadcasts setting
O AUTO: To record NICAM stereo broadcasts and bilingual
broadcasts.
OFF: To record the normal sound (FM mono).
,.s,,:s: ~-wwaws.,.-s.m,%a,s.aws!s“.%~.,a%~.wam-?mm---
.
If the numeric 2 button is pressed .....
2. NTSC PB
NTSC playback
. PAL-TV: When using a PAL system TV.
NTSC443: When using an NTSC4,43 system TV.
Please use the AUDIO/VIDEO OUT terminals.
..
If the numeric 3 button is pressed .....
3. CHILD LOCK
Child lock function
ON: No image will appear on the TV screen and the
sound is muted.
O OFF: The child lock function is not engaged.
a When finished, press the MENU~V button.
ON-SCREEN MENUS AND BASIC CONTROL
The VCR can easily be programmed by using the menus displayed on-screen.
The menus are controlled from the remote control.
The buttons that can be used with each menu are displayed at the bottom of the screen.
If you learn the basic operations, each setting can easily be made by following the steps of the
concerned menu.
If a wrong sub-menu has been selected, press the MENU/TV button to return to the main menu,
and start again.
1. Timer recordina
~
programming -
Recording history
(see page 15)
(see page 16)
MENU
1. T I MER PROGRAM SET
2. PROGRAM CHECK /CLEAR
3. VCR SETUP
4. CLOCK SET
h
G-CCUE
:..
G-CODE NUMBER
489135 ---
[OKI +ENTER
[CLEARI +TO CORRECT
[G-CODE] +TV
G-Code timer recording
programming
(see page 13)
PR DATE START END
02 25.12 10:30
ll:OOW
+------- --: ----: --
w
----, -- --: ---- :_-
----, -- __:--
--:--
----, -- --: ---- :--
----, -- --: ---- :--
ICLEARI +TO CORRECT
[MENU 1 +TV
\ J
I
2. Confirmation/Cancelling
(see page 16)
PR DATE START END
+01 23.12
15:30 16:OOW
02 25.12 10:30 ll:OOW
----, -- __:--
--:--
----, -- --:--
--:--
----, -- --: ---- :--
------- --: ---- :--
[+/-1 +SELECT
[CLEARI +CANCEL
[MENUI +TV
3. VCR Setup
(see page 7)
J
0. AUTO TUNING MEMORY
1. NICAM
OAUTO OFF
2. NTSC PBOPAL-TV NTSC443
3. CH I LD LOCK ON 00FF
[0-91 +SELECT
[MENU] +TV
4. Clock setting
(see page 6)
I
CLOCK SET
f
09.12.96
16:15
I
[+/-l +Tl ME SHIFT
[CLEARI +TO CORRECT
[OKI +ENTER
PR DATE START END
02 25.12 10:30 11:00!?
+-- --, -- --:--
__ :--
P
----, -- --: ---- :--
------- --: ---- :--
----, -- --: ---- :--
----, -- --: ---- :--
[CLEARI +TO CORRECT
[MENUI +TV [+1 +HISTORY
2
PREPARATION
+!
G-CODE
o-9 ;:;
MENU/TV
0
OK
8
3
BASICOPERATION
7+
INDEX
REW
FF
STOP
PLAY
iT
MEMORY
RESET
o-9 ;;;
0
+, -
EJECT PLAY
II
I
I
I
I
REW
Autopoweron
The power is automatically
switched on asa cassette is
inserted while the VCRis in the
stand-by mode.
Autoplay
The VCRwill play back atape
automatically when avideo
cassetteis inserted whose
erasure-prevention tab hasbeen
removed,
Autoeject
When a video cassettewithout an
erasure-prevention tab is played
to the end of the tape, the tape
will be automatically rewound
and then the cassette will be
ejected.
Poweroffeject
The video cassette will be ejected
when the EJECTbutton is
pressed, evenwhen the VCRis in
stand-by mode.
PLAYBACK
1
2
3
4
Turn on the TV, then set it to the preset
video channel or AV mode.
Insert a recorded video cassette.
Cassette loading
Gently push the centre of the cassette
until it is loaded automatically.
Press the PLAY button.
To stop the playback, press the STOP
button.
To rewind the tape, press the REW button.
To advance (fast-forward) the tape, press
the FF button.
To eject the video cassette, press the
EJECT button on the VCR.
Counter memory
The counter memory is used to find a point on
the tape. At the desired point, press the
RESET button to reset the counter to
“0:00:00.
Then, press the MEMORY button to display
“~” to the left of the counter reading.
After recording or playback, that point can be
easily found by pressing the REW button (or
the FF button if the counter reading is
negative), the tape will be rewound (or
fast-forwarded) and stop at the memorized
position.
Notes:
Whenever you load a cassette tape, the counter
is reset to
“0:00:00.
If you play back a blank tape or a blank portion
of tape, the counter will not operate.
Index search
This VCR will go automatically to the
beginning of the next (or present) recording
and start playback.
An index signal is automatically placed at the
beginning of each recording made on this
VCR. This index can be used to search for the
next (or present) recording.
1 Press the INDEX button while in the stop or
playback mode.
To cancel the index search mode, press
the INDEX button again.
2 Press the FF or REW button.
The search function will start.
mmiml
To stop the search function, press the
STOP button.
Notes:
Make sure that indexes are at least five minutes
apart from each other.
Index signals are not recorded after a recording
pause.
Endless play
This function will play back a tape to the end,
rewind it then replay it again, and again until
you stop it.
1 In the stop or playback mode, first press the
PLAY button then while holding it down
press the REW button.
2 To cancel the endless play, press the
STOP button.
If the counter memory function is used in
combination with endless play, the VCR will
play back the tape to the counter reading
“n 0:00:00” then start again from the
beginning.
Counter”~ 0:00:00 position
Beginning
Playback
I
End
Rewind
Notes:
During endless play, please do not press
FF,
REW
or PAUS13STILL button because the
endless play will be cancelled.
This function can only be activated using the
controls on the VCR itself. It cannot be activated
from the remote control.
9
Variable playback modes Shuttle dial operation
Double speed playback
1
Press the X2 button during normal
playback operation.
2 Press the PLAY button to resume normal
playback.
Forward search
1 Press the FF button during playback or
fast-forward operation.
2 Press the PLAY button to resume normal
playback, or the FF button to resume
fast-forward operation.
By simply turning the shuttle dial, you can
easily select the search direction and speed.
When you get to where you want to start
viewing the tape, just release the shuttle dial
to resume playback or still picture (see below).
You can use the shuttle dial during normal
playback or still picture modes.
Using the shuttle dial from normal
playback mode
1 Simply turn the shuttle dial to obtain the
desired mode as indicated by the
illustration.
Reverse search
1 Press the REW button during playback or
rewind operation.
2 Press the PLAY button to resume normal
playback, or the REW button to resume
rewind operation.
Still picture
1 Press the PAUSE/STILL button during
normal playback.
2 Press the PLAY button to resume normal
playback.
Frame advance
1 Press the PAUSE/STILL button during still
playback to advance the picture frame by
frame.
2 Normal playback will resume when you
release the shuttle dial.
W
...
[i
,.-
,.-
...
F II u II ‘i.-’”’”
2 Press the PLAY button to resume normal
1
playback.
Slow motion
,...
Using the shuttle dial from still picture
mode
1
2
Press the SLOW button during normal
playback or during still picture.
The tape speed can be set at 1/5 or 1/30 of
2
normal speed by pressing the
SLOW
button.
Simply turn the shuttle dial to obtain the
desired mode as indicated by the
illustration.
When using the shuttle dial for slow motion
playback, only the 1/5 of normal speed is
available.
Still picture will resume when you release
the shuttle dial.
Press the PLAY button to resume normal
playback.
3
BASICOPERATION
F
SLOW
x2
REW
FF
PLAY
Pyy
“G
Shu;tt
o-9 ;;;
o
+, -
lodes and buttonsillumination
stop
Playba[
Forward se
Reverse sc
Fast-forw
Rewin[
Recon
3
BASICOPERATION
+,-—
11
PLAYBACK
Hi-Fi Stereo/Bilingual programmed
sound selection
Using the AUDIO button, select the desired
sound to listen.
Stereo sound selection
When a stereo broadcast is received, the
stereo indicator “ST illuminates on the VCR
display,
VCR display
Selected sound
“LR”
Left and Right tracks
“L 99
Left track
R“
Right track
No indicator
Monaural
Bilingual sound selection
When a bilingual broadcast is received, the
bilingual indicator “BIL’ illuminates on the
VCR
display,
VCR display
Selected sound
6
Playback of an NTSC tape
This VCR can playback an NTSC tape on a
PAL standard TV receiver.
However, please note the following points.
If the image is unstable, rolling vertically,
use the TV vertical hold button to stabilize
the image.
The image may shrink vertically and a
black band may appear at the top and
buttom of the screen.
An NTSC tape cannot be copied normally.
Picture quality of NTSC tapes cannot be
guaranteed with this VCR.
When an NTSC Hi-Fi tape is palyed back,
the monaural sound only will be heard.
Tracking adjustment
This VCR
starts the automatic tracking
function when you insert the tape. During
playback this function will adjust the tracking
to the best possible image. If
noise appears in
the playback picture, press the (+ or –) button,
to reduce the noise interference in the image.
L p
Noise interference
Note:
Depending on the cassette tape, you may find that
some noise interference cannot be completely
corrected using the tracking controls.
Correcting noise interference during
variable playback modes
If noise interference (bars) appears during
double speed playback
Use the (+ or –) button, to correct,
If noise interference (bars) appears during
still picture, frame advance or slow motion
modes
From still picture or frame advance go into
slow motion mode, then use the (+ or –)
button, to correct. You can then resume still
picture or frame advance mode.
If the still picture moves up and down
Use the (+ or-) button, to correct.
When noise interference is corrected using
the (+ or -) button, the settings will be
effective until the cassette tape is unloaded.
Once the cassette tape is unloaded, the VCR
is reset and the next time the VCR is used
you may need to do the corrections again.
Notes:
During variable playback modes the picture may
contain some noise or vibration that cannot be
corrected, This is not a malfunction.
if still picture or slow motion playback is
continued for about five minutes, the VCR will
automatically change to stop mode in order to
prevent the tape from being damaged.
This VCR will not guarantee the variable
playback modes picture quality of tapes recorded
in LP mode.
i
.-
*
RECORDING TV PROGRAMMED
3
BASICOPERATION
1
2
3
4
5
Turn on the TV then set it to the preset
video channel or AV mode.
Insert a video cassette with
erasure-prevention tab.
Press the numeric buttons, or the (+ or –)
button, to select the TV station to be
recorded.
To select the tape speed, press the TAPE
SPEED button.
SP: Standard Play mode (Best image
and sound quality. No display
indicates SP mode.)
LP: Long Play mode (Twice the SP
mode recording/playback duration.)
Press the REC button.
The “REC indicator will light, and recording
starts.
6
To stop the recording, press the STOP
button.
If you wish to avoid recording
unwanted material
1
2
During recording, press the PAUS13STILL
button.
The TV picture and sound will not be
recorded.
Press the PAUSIXTILL button or REC
button.
The recording will resume.
Note:
If the record pause mode continues for about five
minutes, the VCR will automatically go into the stop
mode in order to prevent damage to the tape.
Recording one programme while
watching another
1 Start recording the desired TV station
programme selected on the VCR.
2 Select on the TV receiver the TV station
you want to watch.
If the VCR has been connected to the TV
using the “AV connection”, set the TV to
the TV mode.
Quick Start Recording timer
Timer recording is simple.
You can start a recording and then
programme when the VCR is automatically
recording and turn its power off.
1 Press the REC button twice.
z Within Ioseconds, setthe recording end
time by using REC and (+ or -) buttons.
REC: units of 30 minutes
(+, -) : units of 1 minute
Rlmlmll
The timer indicator (D) will light after the
recording end time is set.
To stop the recording at any time, press the
STOP button.
Checking/Changing
When the REC button is pressed during Quick
Start Recording, the recording end time will
blink for 10 seconds.
The recording end time can be changed by
pressing REC and (+ or -) buttons during this
10-second period.
REC
3
TAPESPEED
STOP
P:tJ:/[
o-9 !;~g’
p
+, -
Erasure-prevention tab
To prevent accidental erasure,
remove the tab after recording.
To
recordagain,coverthehole
withvinyltape,
.—
Iis-erasure preventioneject
he cassette will automatically be
iected if recording is attempted
n a video cassette without an
rasure-prevention tab.
uto rewind
he VCR automatically rewinds
le tape when it reaches the end.
his function does not operate
Iith timer recording or Quick
tart Recording timer.
12
ON-SCREENOPERATION
rl
TAPESPEED
‘-’’”-h I
ii%
MENWTV
o-9 ;;;
CLEAR
0
OK
+, -
G-Codeisa
trademark applied for
by Gemstar Development Corp.
G-Codesystem is manufactured
under license from Gemstar
Development Corporation.
NewspaperorTVguide
Code number
13
G-CODE TIMER RECORDING
PROGRAMMING
i
This VCR has a built-in G-Code system.
Programming timer recordings is now as
simple as entering a Code number number (1
to 9 digits) listed next to each programme in
your local TV guide or newspaper TV
programme listing.
There are two ways of programming G-Code
timer recordings.
One is using the on-screen display and the
other one is using the VCR display,
You can set up to 6 programmed to be
recorded upon a period of up to 1 year.
On-screen programming
1 Turn ontheTV then set ittothe preset
video channel or AV mode.
z Press the G-CODE button.
If 6 timer recordings have already been set,
the programmed timer recordings list will
appear on the TV screen.
Piease refer to “Confirmation” and
“Canceling” on page 16.
G-CODE NUMBER
---------
I
3
Using the numeric buttons, enter the
Code number for the programme you
want to record.
~xan@e: Enter the code number 489135.
G-CODE NUMBER
489135 ---
I
If you entered a wrong number, press the
CLEAR button to delete it, then enter the
correct number.
a Press the OK button.
The settings for the programmed recording
are displayed.
I
G-CODE NUMBER
489135 ---
I
PR DATE START END
+01 25.12 15:00 16:00$!
I
Notes:
If the programme position number (PR) displays”-
-“ :
Enter the programme position number the TV
station has been preset to.
That setting will be memorized and set the next
time the same TV station is selected.
5 When allthesettings areas desired,
press the OK button.
You can programme another recording by
repeating steps 3 to 5.
6
Insert a video cassette with
erasure-prevention tab.
Make sure the tape is longer than the total
recording time.
T Press the G-CODE button.
The timer indicator (~) will light on the
VCR display and the VCR goes into timer
recording stand-by mode.
Additional settings
After pressing the OK button in step 4.
Daily/Weekly recording
Press the MENU~V button repeatedly to
select:
“M-F: for daily recording (Monday through
Friday)
“WK: for weekly recording (the same
programme every week)
No display: for one time recording
Note:
Daily recording starting on a Saturday or Sunday
will not be possible.
Recording tape speed setting
Press the TAPE SPEED button repeatedly to
display the desired tape speed.
No display: Standard Play mode
LP: Long Play mode
Changing the off time
Each press of the (+ or -) button will change
the recording off time by units of 10 minutes.
Notes:
If the date and time are not set, the G-CODE
button will not function.
The (~) indicator will flash if no video cassette is
loaded when going into timer stand-by mode.
The (~) indicator will flash and the video
cassette is ejected if a video cassette with no
erasure-prevention tab is loaded.
Programming on the VCR display
You can programme or confirm a G-Code
timer recording on the VCR display even if the
TV is turned off.
1 F’ress the G-CODE button.
9 bars (–) will appear on the display.
If 6 timer recordings have already been set,
the 9 bars (–) are not displayed.
Please refer to “Confirmation” and
“Canceling” on page 16.
z Using thenumeric buttons, enter the
Code number for the programme you
want to record.
Example: Enter the Code number 489135
If you entered a wrong number, press the
CLEAR button to delete it, then enter the
correct number.
3
Press the OK button.
The programmed recording programme
position number and recording on time
are displayed.
Notes:
If the programme position number ~PR”) displays
‘~--,~:
Enter the programme position number the TV
station has been preset to.
That setting will be memorized and set the next
time the same
TV station is selected.
A When allthesettings areas desired,
press the OK button.
You can programme another recording by
repeating steps 2 to 4.
5 Insert a videocassette with
erasure-prevention tab.
Make sure the tape is longer than the total
recording time.
6
Press the G-CODE button.
The timer indicator (~) will light on the
VCR display and the VCR goes into timer
recording stand-by mode.
Additional settings
After pressing the OK button in step 3.
Daily/Weekly recording
Press the MENU~V button repeatedly to
select:
“M-F: for daily recording (Monday through
Friday)
“WK: for weekly recording (the same
programme every week)
No display: for one time recording
Note:
Daily recording starting on a Saturday or Sunday
will not be possible.
Recording tape speed setting
Press the TAPE SPEED button repeatedly to
display the desired tape speed.
No display: Standard Play mode
LP: Long Play mode
Changing the off time
Each press of the (+ or –) button will change
the recording off time by units of 10 minutes.
Note on sky decoders and recording
There are at present two types of sky
decoders available in New Zealand.
1. Base Band Decoder (no remote control
supplied, older type).
You cannot successfully record G-Code
programmed using this type of decoder.
(Unless your video is modified internally first.)
Contact Sky TV for details.
2. IRD Decoder (supplied with Sky Remote and
with UHF output).
This decoder allows you to programme
recordings using the G-Code function. You
can use the Sky CODE NUMBERS to record
Sky
TV programmed with your VCR.
However, please note the following limitations.
(a) The Sky CODE NUMBERS used with the
VCR
can not change the channels on the
Sky Decoder.
This means you must first preselect the
Sky channel you want to record (movies,
sport, news)
(b) The VCR will then turn on and record the
programme position which has been set
for Sky. (e.g. programme position “4).
The Sky channel you record (movies,
sport, news) will depend on which channel
the decoder was left on.
(c) Remember the first time you use a Sky
CODE NUMBER, the programme position
number
(’rPR”) on the video needs to be
set the same for all three Sky channels.
This will depend on the programme position
number you allocated for Sky in the set up.
ie program me position number “4.
ON-SCREENOPERATION
$
TAPESPEED
G-COOE
MENU/TV
o-9 ;;;
CLEAR
0
OK
+,
14
ON-SCREENOPERATION
POWER
n
TAPESPEED
$
MENU/TV
INPUT
o-9 {;;
CLEAR
0
+
OK
15
i
ON-SCREEN TIMER RECORDING
PROGRAMMING
ExamP/e; program me position,,. 02
1
2
3
4
Date.,. 25 December
Start time... 21:30
End time... 23:15
Turn on the TV then set it to the preset
video channel
or AV mode.
Press the MENU~V button.
Press the numeric
1 button.
Using the numeric buttons, set the
programme position number (e.g. “02”),
Example; Enter 02.
v
5
Using the numeric buttons, set the date
(e.g. 25 December).
ExamP/e: Enter 2512.
If you entered a wrong number, press the
CLEAR button to delete it, then enter the
correct number.
I
PR DATE START END
+02 25.12 --:-- --:--$?
6
Set the recording start and end times (e.g.
start 21:30, end 23:15).
ExamP/e; Enter213023 15.
Y
T When allthesettings areas desired,
press the OK button.
You can programme another recording by
repeating steps 4 to 7.
8
Insert a video cassette with
erasure-prevention tab.
Make sure the tape is longer than the total
recording time.
9
Press the POWER button.
The timer indicator (~) will light on the VCR
display and the VCR goes into timer recording
stand-by mode.
To record from an external source
At step 4,
Press the INPUT button.
“L1” is displayed instead of the programme
position number.
If a programme position number is already
displayed, first press the CLEAR button.
Additional settings
After step 5,
Daily/Weekly recording
Press the (+) button repeatedly to select:
“M-F: for daily recording (Monday through
Friday)
“WK: for weekly recording (the same
programme every week)
No display: for one time recording
Note:
Daily recording starting on a Saturday or Sunday
will not be possible.
Recording tape speed setting
Press the TAPE SPEED button repeatedly to
display the desired tape speed.
No display: Standard Play mode
LP: Long Play mode
i
ON-SCREEN TIMER RECORDING PROGRAMMING
ON-SCREENOPERATION
Confirmation
To correct a programmed timer recording,
first cancel it, then reprogrammed it as
desired.
To cancel a programmed timer recording,
continue with step 3.
To return to the normal TV broadcast
2
POWER
MENU/TV
o-9 :;;
CLEAR
,0
OK
+,-
1 Pre.ss the MEN”~V button.
P
screen, press the MENU/TV button.
Canceling
[0-91 +SELECT
[MENU] +TV
09.12.96
16:15
Using the (+ or –) button, select the3
programme to cancel.
Z FYessthenurneric 2buNon.
‘rogrammepriority
PR DATE START END
01 23.12 15:30 16:00!/
+02 25.12 10:30 II:OOY
----, ---- :---- :--
----. ---- :---- :--
-- _-, ---- :---- :--
----, ---- :---- :--
[+/-] +SELECT
[CLEARI
CANCEL
[MENUI +TV
Programmed timer recordings are listed.
I If several timer recordings
haveoverlapping recording
time, the recording with the
PR DATE START END
+01 23.12 15:30 16: OO$J
02 25.12 10:30 11:00$1
_____ ---- :---- :--
_- __, ---- :---- :--
_- __, ---- :---- :--
----,-- --: ---- :--
[+/-]
SELECT
[CLEARI +CANCEL
[MENUI +TV
earliest start time will be
recorded first, until the end.
19:00
20;00
21:00 22:00 2300
mimq
4
5
Press the CLEAR button.
I
I
1
I
When finished, press the MENWTV
button.
hese portions
will not be recorded
RECORDING HISTORY
ON-SCREENOPERATION
This VCR memorizes the settings of 5
previous timer recordings.
Using these settings, you can now easily
proqramme a timer recording for a
Memorized recordings settings
~ PR DATE __START END ~
: 01..1.0,.1.1 ......
lo.;.o.o._l_o_:30_y }--j-
~
02 9.11
17:00 18:00S? :
~ 03 8.11
11:48 11:49$ ~
programme on the same day of the week and
at the same hour that a programme previously
‘m
recorded.
1 Press the MENU~V button.
z Press the numericl button.
_--_, ---- :---- :--
----, ---- :---- :--
[OKI +ENTER
[CLEARI +TO CORRECT
[MENUI +TV [+1 +H I STORY
I
PR DATE START END
01 13.11
12:00 12:30W
03 13.11
17:00 18:00S!
+------- --: ----:--
------- _-: ---- :--
----, -- --: ---- :--
-- _-, ---- :---- :--
[CLEARI +TO CORRECT
[MENUI +TV [+1 +H I STORY
Votes:
If a previous timer recording
was set for daily (Monday
through Friday) or weekly
recording, the settings are not
memorized,
If the VCR is reset, the
recording history memory will
be erased.
To correct the newly programmed recording
settings, first press the CLEAR button to
erase them, then reprogramme them as
desired.
d Press the OK button.
Repeat steps 3 and 4 to programme up to 5
new timer recordings.
3
Press the (+) button.
Every time the (+) button is pressed, using
one of the 5 memorized recordings data, a
programmed timer recording will be
displayed for the next same day of the
week.
Press the MENU/TV button to return to the
normal TV screen.
Load a cassette tape, then press the
POWER button and the VCR will go into
timer recording stand-by mode.
16
5
ADVANCEDOPERATION
u
INPUT
Externalinputmode selection
Press the INPUTbutton.
“L1”or “L2”is displayed instead
of the programme position
number.
“LI”: AUDIOMDEO IN (Rear)
“L2”: AV INPUT (Front)
Notes:
If you are using a tape with a
monaural only original sound
recording, the audio dubbing
will erase the original sound,
Audio dubbing is only possible
on a tape with Hi-Fi original
sound.
After an audio dubbino, to
listen to the Hi-R sou;d,
press the AUDIO button to
display the “L”and “R”
indicators on the VCR display.
To listen to the dubbed sound,
press the AUDIO button to
erase the “L”and “R”
indicators from the VCR
display.
Audio dubbing
(*)Stand-by
~m
Dubbing
~-
(;~!: Flashing)
17
ii
EDITING
Tape copy
Audio dubbing
Copying (dubbing) a tape can be done using
two video recorders, a playback VCR and a
recording VCR.
Recording VCR
~ I ;~–—”
1 !-)n
I Playback VCR (Camcorder)
I
(-gjPJ,–~
Camcorder
VCR
for recording VCR
1
2
3
Insert a video cassette with
erasure-prevention tab.
To select the tape speed, press the TAPE
SPEED button.
Set to the record pause mode.
The record pause mode is set by pressing
the REC button then the PAUSEETILL
button.
for playback VCR (Camcorder)
A insert the recorded videocassette.
s Start playback by pressing the PLAY
button.
for recording VCR
6
When the desired starting position is
reached, start recording by pressing the
PAUSEK3TILL button or the REC button.
1 When finished, press the STC)P button on
the recording VCR then on the playback
VCR.
CAUTION:
The unauthorized recording of television
programmed, video tapes, films and other
such material may infringe upon copyright or
the rights of third parties.
Using this function, you can add a voice over
or background music to the image recorded
on a tape.
To perform an audio dubbing on a tape
recorded with a camcorder, you will have to
first make a Hi-Fi copy of the camcorder tape
to a VHS format video cassette using this
VCR.
You can then add a voice over or background
music to the copy you have made.
I Ju.idiosource
I
Camcorder Audio system
1 Insert avideo cassette tape with
erasure-prevention tab.
Make sure the recorded sound (original
sound) is Hi-Fi.
2
3
4
Playback the tape to select the audio
dubbing start point.
Press the PAUSER3TILL button at the
audio dubbing start point.
Press the A-DUB button.
The VCR goes into audio dubbing stand-by
mode(*). The “L and “R indicators will go
off. If monitoring the external sound, the
sound will be heard.
5 Press the A-DUB button again tostart the
audio dubbing.
6
When finished, press the STOP button.
m
i
TROUBLESHOOTING
Symptom
Check points
POWER TROUBLE
No power
The power cord is disconnected.
4
i
I
The remote control unit
The batteries are low.
doesn’t operate
1
3
RECEIVER TROUBLE
No TV programmed . Are the connections between your VCR and TV correct?
4
received
Was tuning correctly preset?
6
Off the air reception on the
. The video channel setting of the TV
receiver does not
VCR is poor correspond to the video channel presetting of the VCR.
I
5
PLAYBACK TROUBLE
Playback picture does not
The video channel setting of the TV receiver does not
appear correspond to the video channel presetting of the VCR.
I
5
Interference in playback
Adjust the tracking control.
picture
-“L
Dust or dirt on video heads. Take the VCR to an Authorized
Service Centre.
RECORDING TROUBLE
No recording . The erasure-prevention tab on the cassette has been
removed.
I
12
Timer recording is not
The starting day and time have not been set correctly.
15
possible
. The clock time is not set correctly.
6
I . There has been a power interruption of more than 1 hour. I 7
Hi-Fi TROUBLE
Sound of a Hi-Fi recorded
The tape might be defective.
tape drops out
Use a new video cassette tape.
1-
1AC6P1P1226--
PK4HN/NZC2P (0596 KP-NIOI )
s
*O
SANYO Electric Co., Ltd.
Printed in Indonesia
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Sanyo VHR-690 User manual

Category
Cassette players
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI