MicroNet SP880B Quick Installation Guide

MicroNet
Brand
MicroNet
Model
SP880B
Category
Networking
Type
Quick Installation Guide

This manual is also suitable for

P/N: 2300-0515
5
6
7
Broadband VPN Router
Model No.: SP880B/SP881B/SP883B/SP891
Quick Installation Guide
Configuration
Follow the steps below to configure and set up Broadband
Router.
IP Address Configuration
PC/Notebook must belong in the same IP range and subnet.
Follow the steps below to configure IP settings for LAN PC.
Step 1.
In the control panel, double click
on Network Connections.
Double click on the local area
connection (e.g. LAN). The
following screen will appear.
Highlight 'Internet Protocol
(TCP/IP)' and click on
'Properties'.
Step 2.
Select 'Obtain an IP address
automatically' and 'Obtain DNS
server address automatically',
then click <OK>.
Step 3.
In DOS command, type 'ipconfig' to view information on LAN
connection. Ensure the IP address and subnet mask are on the
same subnet as the router.
Default Values
IP Address
Subnet Mask
Username
Password
192.168.1.1
255.255.255.0
'admin'
Leave the password field blank
Web-based User Interface
Micronet's Broadband Router is embedded with http sever and
provides a series of web pages, which display the configuration
and status of the system. After configuration of IP, the
management interface can be access by entering the IP
address of the router into the browser.
1. Login page will
appear to prompt users
to enter the username
and password.
2. After correctly
entering the login
details, the following
interface will appear.
Please enter new
password details and
press <Submit>.
3. Enter the WAN
connection in the field
below. Information like IP
details, username and
password can be
obtained from your ISP.
Press <Submit and
Reboot> to restart the
device.
Web: www.micronet.com.tw ; www.micronet.info
2
Introduction
Micronet SP880B/SP881B/SP883B/SP891, Broadband Router
with Firewall, delivers a complete broadband solution for both
Cable and DSL connections. It comes equipped with one/two
WAN port and incorporates a four 10/100Mbps ports switching
hub. Supported connection methods include Fixed IP, Dynamic
IP, PPPoE and PPTP. Security is intact by the in-built firewall
with support of Multi-DMZ. Other security protections include:
Special Applications, Virtual Servers, Access Filter, URL Filter
and VPN Pass-Through. It is ideal for small-to-medium
enterprise who emphasizes on Internet safety for its network
core.
Package Contents
Prior to the installation of the device, please verify the following
items are in the package:
• SP880B/SP881B/SP883B/SP891 Broadband Router
• Quick Installation Guide
• Manual CD
• RJ-45 Ethernet Cable
• Power Adapter
Physical Description
1
• Ensure both router and Cable/DSL modem are switched off.
Leave the modem connected to their data line.
• Connect the modem to the WAN port of the router using a
RJ-45 Ethernet Cable.
• Connect PC to the router via one of the LAN port using a
RJ-45 Ethernet Cable.
• Connect the provided power adapter on router's Adapter port
and power on both modem and router.
• Check the LEDs to verify successful connection.
1. The power LED should be on.
2. WAN LED should be on if it is connected to a modem.
3. The Error LED will light up during startup then turns off.
If the LED remains on, there will be error in your setup.
Please recheck steps above.
4. For each LAN port that is connected, its corresponding
LED will light up to indicate successful connection and
traffic for the port.
•
•
•
•
•
•
•
•
•
•
•
•
Hardware Installation
3 4
LED Status
POWER
On
Off
Status
Operation
Power is on
Power is off
On Firmware not loaded or Hardware Error
Off
Normal operation
Blinking Data In/Out
Green 100BaseT Detected
LINK/ACT
(WAN/LAN
/DMZ)
Orange
Off
10BaseT Detected
No connection
SP880B Broadband VPN Router
POWER
STATUS
4 321
LAN
WAN
LINK/ACT
10M/100M
SP880B Front View
SP880B Rear View
LANWANDC 5V
4 3 2 1
RESET
SP881B Front View
SP881B Rear View
LAN DMZ WANDC 5V, 1.5A
4 3 2 1
RESET
SP881B Broadband VPN Firewall
POWER
STATUS
WAN DMZ
4 321
LAN
LINK/ACT
10M/100M
SP883B Front View
SP883B Rear View
SP883B Broadband Bandwidth Controller
POWER
STATUS
4 321
LAN
WAN
LINK/ACT
10M/100M
LANWANDC 5V
4 3 2 1
RESET
SP891 Front View
SP891 Rear View
LANWAN 2DC 5V WAN 1
4 3 2 1
RESET
SP891 Multi-WAN Security Gateway
POWER
STATUS
4 321
LAN
1 2
WAN
LINK/ACT
10M/100M
Other LED Indications (SP881B)
• WAN Link/Act LED continuous Flash: MAC address not
assigned.
• WAN Link/Act LED solid On: SDRAM error.
• LAN1 Link/Act LED solid On: Timer/Interrupt error.
•
  • Page 1 1
  • Page 2 2

MicroNet SP880B Quick Installation Guide

MicroNet
Brand
MicroNet
Model
SP880B
Category
Networking
Type
Quick Installation Guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents