Mitsubishi VS-55705 Owner's manual

MITSUBISHI

THE BIG SCREEN COMPANY TM

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER

(OR BACK).

NO USER-SERVlCEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

RISKOF ELECTRICSHOCK

DO NOT OPEN

/_The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert

the user to the presence of uninsulated"dangerous voltage within the products enclosure

that may be of sufficient magnitude to constitute a risk of electric shock.

//_ The exclamation point within an equilateral triangle is intended to alert the user to the

presence of important operating and maintenance (servicing) instructions in the literature

accompanying the appliance.

Warning: To avoid permanently imprinting a fixed imageonto yourTV screen,pleasedo not displaythe same

stationary imageson the screen for more than 15%of your total TV viewing in one week. Examplesof stationary

imagesare letterbox top/bottom barsfrom DVD disc or other video sources,side barswhen showing standardTV

pictures on widescreenTV's,stock market reports, video game patterns, station logs,web sitesor stationary com-

puter images. Suchpatterns can unevenly agethe picture tubes causing permanent damageto theTV. Pleaseseepage

58 for a detailed explanation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in accordance with the instruc-

tions, may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful interfer-

ence to radio or television reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or reJocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

Changes or modifications not expressly approved by Mitsubishi could void the user's authority to operate

this equipment.

WARNING:

TO REDUCETHE RISKOF FIREOR ELECTRIC SHOCK, DO NOT EXPOSETHISAPPLIANCETO RAIN OR

MOISTURE.

CAUTION:

TO PREVENTELECTRICSHOCK, MATCH WIDE BLADE OF PLUGTO WIDE SLOT,FULLYINSERT.

NOTE TO CATV SYSTEM INSTALLER:

THIS REMINDER ISPROVIDEDTO CALLTHE CATV SYSTEMINSTALLER'SATTENTION TOARTICLE 820-40 OF

THE NEC THAT PROVIDESGUIDELINES FOR PROPERGROUNDING AND, IN PARTICULAR,SPECIFIESTHAT

THE CABLE GROUND SHALL BECONNECTEDTOTHE GROUNDING SYSTEMOFTHE BUILDING,AS CLOSE

TOTHE POINT OF CABLE ENTRYAS PRACTICAL.

Contents

Important Safeguards 5

Instructions on safety and proper handlingof your Mitsubishi television

Special Features 7

Distinctive features, items included with your Mitsubishi television and hookup guidelines

Shortcuts 8

A quick reference list

Connections 9

Basichookups to an antenna, cable and components

Remote Control Functions 15

Features of the remote control, programming to work with other audio and video products,

explanation of buttons

Thel_H ° Menu System 2 I

Explanation of the on-screen menu system and the basic set-up menu screens including

Memorizing Channels, Set Clock and Day, AV Connection and On-Screen Language

Remote Control Input and Channel Selection 3 I

Changing inputs and channels and setting the sleep timer with the remote control

The Main Menu Screens 33

Explainsthe Parent Lock, Channel Edit, Advanced Features and Audio/Video Settings Menus

Special Remote Control Functions 49

How the remote works with other products includingthe Mitsubishi A/V Network, viewing

the PIP (Picture-in-Picture) and POP (Picture-outside-Picture)

Control Panel Functions 54

Explanation of the front panel buttons and the back panel terminals

Troubleshooting 57

Common problems, notes on caring and cleaningyour Mitsubishi television and how to

obtain service

Appendices 6 I

Diamond ShieldTM installation, remote control programming codes, bypassing the parent lock

This page is blank

Please read all these instructions regarding your television set and retain for future refer-

ence. Follow all warnings and instructions marked on the television.

I. Read, Retain and Follow Instructions

Readall safety and operating instructionsbefore operating the appliance.Retain the safety and operating

instructionsfor future reference. Follow all operating and useinstructions.

2. Heed Warnings

Adhere to all warnings on the applianceand in the operating instructions.

3. Cleaning

Unplug thisTV receiver from the wall outlet before cleaning. Do not useliquid or aerosol cleaners.Cleaners

canpermanently damagethe cabinetor screen.Use adamp cloth for cleaning.

4. Attachments and Equipment

Never add anyattachments and/or equipment without approval of the manufacturer assuchadditions may

result inthe risk of fire, electric shock or other personal injury.

5. Water and Moisture

Do not usethisTV receiver where contact with or immersioninwater ispossible. Do not usenear bath

tubs, wash bowls, kitchen sinks,laundrytubs,swimming pools,etc.

6. Accessories

Do not placethis TV receiver on an unstablecart, stand,tripod, bracket, or table. TheTV receiver mayfall,

causingserious injuryto a child or adult, and serious damageto the appliance. Use only

with a cart, stand,tripod, bracket, or table recommended by the manufacturer,or sold with

theTV receiver. Any mounting of the applianceshould follow the manufacturer's instruc-

tions, and should usea mounting accessory recommended bythe manufacturer.

An applianceand cart combination should bemoved with care. Quick stops, excessive

force, and uneven surfacesmay causethe applianceandcart combination to overturn.

7. Ventilation

Slots and openingsin the cabinet are provided for ventilation and to ensure reliable operation of theTV

receiver and to protect it from overheating. Do not block these openingsor allow them to be blocked by

placingtheTV receiver on a bed,sofa,rug,or other similar surface. Nor should it be placed over a radiator

or heat register. If the TV receiver isto be placedin a rack or bookcase,ensure that there isadequate

ventilation and that the manufacturer's instructionshavebeen adhered to.

8. Power Source

This TV receiver should be operated only from the type of power source indicatedon the marking label. If

you are not sure of the type of power supplied to your home, consult your appliancedealeror local power

company.

9. Grounding or Polarization

This TV receiver isequipped with a polarized alternating current lineplug havingone blade wider than the

other. This plug will fit into the power outlet only one way. If you are unableto insertthe plug fully intothe

outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your

obsolete outlet Do not defeat the safety purpose of the polarized plug.

I0. Power-Cord Protection

Power-supplycords should be routed so that they are not likely to be walked on or pinched by items placed

upon or againstthem, payingparticular attention to cords at plugs,convenience receptacles,and the point

where they exit from the appliance.

5

I I. Lightning

For added protection for thisTV receiver during a lightningstorm, or when it isleft unattendedand unused

for longperiods of time, unplug it from the wall outlet and disconnect the antennaor cable system. This will

prevent damageto theTV receiver due to lightning and power-line surges.

12. Power Lines

An outside antenna system should not be located in the vicinity of overhead power linesor other electric

light or power circuits, or where it can fail into such power linesor circuits. When installing an outside

antennasystem,extreme care should be taken to keep from touching such power lines or circuits ascontact

with them might be fatal.

13. Overloading

Do not overload wait outlets and extension cords asthis canresult ina risk of fire or electric shock.

14. Object and Liquid Entry

Never pushobjects of anykind into this TV receiver through openingsasthey maytouch dangerousvoltage

points or short-out parts that could result in a fire or electric shock. Never spill liquid of anykind on theTV

receiver.

EXAMPLE OF ANTENNA GROUNDING

15. Outdoor Antenna Grounding

If an outside antennaor cablesystem isconnected to the TV receiver,be sure

the antenna or cable systemisgrounded so asto provide some

protection againstvoltage surgesand built-up static charges.

Section 810 of the National Electrical Code,ANSI/NFPA

70-1984,provides informationwith respect to proper

grounding of the mast and supporting structure, grounding

of the lead inwire to an antennadischarge unlt, size of

grounding conductors, location of antennadischargeunit,con-

nection to grounding electrodes, and requirements for the

grounding electrode.

LEADIN WIRE

{NEC SECTION 810-20)

GROUNDkNG

CONDUCTORS

=_POWE R SERVIC E GROUNDING

ELECTRODE SYSTEM

NEC -. NATkONAL ELECTRICAL CODE {NEC ART 250, PART H)

16. Servicing

Do not attempt to service this TV receiver yourself asopening or removing covers may expose you to

dangerousvoltage or other hazards. Refer all servicing to qualified service personnel.

17. Damage Requiring Service

Unplug this TV receiver from the wall outlet and refer servicing to qualified service personnel under the

following conditions:

(a)When the power-supply cord or plug is damaged.

(b) If liquid hasbeen spilled,or objects havefallen into theTV receiver.

(c) If theTV receiver hasbeen exposed to rain or water.

(d) If theTV receiver does not operate normally by following the operating instructions, adjust only those

controls that are covered by the operating instructions asan improper adjustment of other controls may

result in damageand will often require extensive work by a qualified technician to restore theTV receiver to

itsnormal operation.

(e) If theTV receiver hasbeen dropped or the cabinet hasbeen damaged.

(f)When the TV receiver exhibits a distinct changein performance -- this indicatesa need for service.

18. Replacement Parts

When replacement parts are required, be sure the service technician hasused replacement parts specified

by the manufacturer or havethe samecharacteristics asthe original part. Unauthorized substitutions may

result in fire, electric shock or other hazards.

19. Safety Check

Upon completion of anyservice or repairs to this TV receiver,askthe service technician to perform safety

checksto determine that the TV receiver isin safeoperating condition.

0 ComponentVideo Input - for the best picture from DVD players

0 DiamondShield TM- protective screen shield for modelsVS-50705,

VS-55705,VS-60705 andVS-70705

0 IRIS TM - sensor that automatically adjusts brightness and contrast, for

models VS-50705,VS-55705,VS-60705 andVS-70705

0 Multibrand Remote Control - use one remote control for many

audio video components

The following items are included with your newTV:

Remote C0ntr_

m II

2 AAA

batteries

The connections shown in this book are general. Cable systems as well as individual audio andlor

video components can vary from those shown here. The first diagram show basic connections

to antenna or cable systems. After you have completed these, you can then connect any addi-

tional components (stereo, DVD, AV receiver, etc.).

IMPORTANT

To maximize your system for its best

performance, your dealer can help you

customize hookups and sell you any

additional connection accessories that

may be needed for your individual

equipment.

7

0 Hooking up yourTV to an antenna or wall outlet cable

0 Remote control functions - pages 19-20

0 Menu screen summaries - page 22-24

0 Selecting the input - page 3 I

0 Setting theV-chip parent lock - page 33

0 Picture-in-picture mode - page 50

0 Picture-outside-picture mode

(forVS-50705,VS-55705,VS-60705 andVS-70705)

0Troubleshooting- page 57

- page 9

-p_e52

TV to Antenna orWall Outlet Cable

Separate UHF andVHF antennas

I, Connect the UHF andVHF

antenna leads to the UHF/VHF

combiner,

2, Press the combiner ontoANT-A

on theTV back panel.

VHF Antenna UHF A_ter _a

_3) (Channel 14_9)

Rat TwEn Le_d F_t TW_E_L_ad 1

1

External

A_t_a

or Ca_

OPTIONAL"

30_Ognrm t°

Bacl; Sole

TV Back Panel

ANT.A

®

00

O0

o

i

o o

@®@

®@@

o_, @o®

*there are different combiners for different wires.

Check with your dealer for the combiner style that you need.

Twin lead antenna or wall outlet cable

For antenna with twin fiat

leads

I, Connect the 300 ohm twin leads to

the transformer.

2. Push the 75 ohm side of the trans-

former onto ANT-A on theTV

back panel,

For cable or antenna with

coaxial lead

Connect the incoming cable to

ANT-A on the TV back panel,

fs Ohm ,

2°°.....L/

Twin Leaa

J

z

_o Ohm _ to 7_ Ohm out

Ma_r_i_g _r_ns_ormer

TV Back PaneI

o 6

@ @@

@@ @@

%e %o

®

Connection of TV to Cable Box

I, Connect the incoming cable to

ANT-A on the TV back panel.

2, Connect two coaxial cables as

follows:

• One from CABLE LOOP-OUT on

theTV back panel to IN on the

back of the cable box,

• One from OUT on the back of the

cable box to ANT-B on theTV

back panel,

TV Back Pane]

Incoming Ca_

Connection ofTV toVCR and Cable Box

I. Connect the incoming cable toANT-A

on theTV back panel.

2. Connect three coaxial cables as follows:

• One from CABLE LOOP-OUT on the

TV back panel to IN on the back of the

cable box.

• One from OUT on the back of the

cable box to ANTENNA IN on the

VCR back panel.

• One from ANTENNA OUT on the

VCR back panel to ANT-B on the TV

back panel.

C_BL_

ANTAL0_O0UT A_T B

®®

©

TV Back Pa_e_

,i@

® ® @

® ® ®

®o®

V6R Back Pa_l

If your VCR has a video channel

ONIOFF sw[tch_ set _tto OFF,

Audio Video Connections

I. Connect a video cable fromVIDEO

OUT on theVCR back panel toVIDEO

INPUT I or INPUT 2 on theTV back

panel.

If you have a S-VHS VCR, follow the

same steps, using the S-Video terminals

on the VCR and TV.

2. Connect a set of audio cables from

AUDIO OUT on theVCR back panel

to AUDIO INPUT on the TV back

panel. The red cable connects to the R

(right) channel and the white cable

connects to the L (left). If yourVCR is

non-stereo, connect only the L (left)

cable.

,@

®

o

®

TV B_ck Pane

°&

RCA

p[_ t pe

CabEe

VCR Back pa_e_

If your VCR has a video channel

ON/OFF switch, set it to OFF,

RCA pin t e

Attach

only

cablo

typ_

S-Video

_ype cable

10

Connection ofTV toVCR and Antenna or

Wall Outlet Cable

Antenna/Cable Connections

I, Connect the incoming cable toANT-A

on theTV back panel,

2, Connect two coaxial cables as follows:

• One from CABLE LOOP-OUT on the

TV back panel toANTENNA IN on the

VCR back panel,

• One fromVCR back panelANTENNA

OUT to ANT-B on the TV back panel,

If your VCR has a video channe{

ON/OFF switch, set it to OFF,

® ® i@ii@ @

_T A _JTA_T

®

Audio/Video Connections

I. Connect a video cable fromVIDEO

OUT on theVCR back panel toVIDE@

INPUT I or INPUT 2 on theTV back

panel.

If you have a S-VHS VCR, follow the

same steps, using the S-Video terminals

on the VCR and TV.

2. Connect a set of audio cables from

AUDIO OUT on theVCR back panel to

AUDIO INPUT on the TV back panel.

The red cable connects to the R (right)

channel and the white cable connects to

the L (left). If your VCR is non-stereo,

only connect the L (left) cable.

VCR Sack Panel

If your VCR has

a video channel

ON/OFF switch,

set it to OFF

®

II

Connection of TV to Stereo Audio System

I. Connect the audio cables from AUDIO

MONITOR OUTPUT on the TV back

panel toTV IN orAUX IN terminals on

the back of the audio system. The red

cable connects to the R (right) channel

and the white cable connects to the L

(left) channel.

2. Turn off the TV'S speakers through the AV

Connection Menu (page 27).

3. Set the audio system's input to theTV or

AUX position to hear the TV's audio

through your stereo system.

Audio _y_Lern teat tetrn_na_

TV Back Pa_e_

of _b

o @@

®

Connection of TV to the Active A/V Network

To control your Mitsubishi audio and/or video products with one remote control

Connect the A/V network cable from

ACTIVE A/V NETWORK on theTV

back panel to IN on the back of a

Mitsubishi component that hasA/V

network terminal.

IMPORTANT

Check the Owner's Guide of your

added Mitsubishi components to

ensure the best possible connections.

Mi_subishiCompone£treartermJnals

TV Back Panek

® @ ®

®® ® ® ®

@@@

ACTWEAN

N_TWORK

12

Connection of TV to AV Receiver

I. Connect a video cable from VIDEO

MONITOR OUT on the back of the AV

Receiver toVIDEO INPUT I on theTV

back panel using aVIDEO cable,

2, Connect a video cable fromVIDEO

MONITOR OUTPUT on the TV back

panel toVIDEOTV IN on the back of

the AV Receiver,

3, Connect a set of audio cables from

AUDIO OUTPUT on the TV back

panel to AUDIOTV IN on the back of

theAV Receiver. The red cable con-

nects to the R (right) channel and the

white cable connects to the L (left)

channel.

TV _ack paneE

®

AV RECEIVER

F_

F_JD-

13

Connection of TV to DVD with ComponentVideo

Outputs

IMPORTANT

For Digital Audio connections, see

the Owner's Guides of your DVD

Player and AV Receiver.

For ComponentVideo Connections

I. Connect the ComponentVideo cables

from VIDEO OUT on the back of the

DVD player to DVDVIDEO INPUT on

the TV back panel, matching the correct

components:

• Y toY,

Cr to Cr,

Cb to Cb.

2. Connect a set of audio cables from

AUDIO OUT on the back of the DVD

player to DVD AUDIO INPUT on the

TV back panel. The red cable connects

to the R (right) channel and the white

cable connects to the L (left) channel.

TV Back Panel

I 0

o

DVD Rear Terminal

Warning: Don't display the same stationary images on the screen for more than 15%of your total TV

viewing in one weelc Examples of stationary images are letterbox top/bottom bars from DVD disc or

other video sources, side bars when showing standard TV pictures on widescreen TV's, stock market

reports, video game patterns, station logs, web sites or stationary computer images. Such patterns can

unevenly age the picture tubes causing permanent damage to the TV. Please see page 58 for a detailed

explanation.

14

For Models VS-45605

and VS-50605

REC STOP PAUSE

REW/REV FF/FWD

PLAY

_ MITSUBISHI

light

Additional features of Models

VS-50705, VS-55705,VS-60705

and VS-70705

REC STOP PAUSE

REW/REV FF/FWD

pLAy

,_ MrrsuBISHI

GUIDE button

for DSSsystems

15

OperatingYour Remote Control

Installing the batteries

I. Removethe back cover of the remote control by pushingthe

the direction of the arrow and slidingoff the cover.

2.Load the batteries, makingsure the polarities(+) and (-) are correct.

IMPORTANT

When you replace the batteries in your remote

control, the remote may return to its initial

setting. You may need to set up your remote

again.

tab in

For best results

Be within 20 feet of the equipment when using the remote control.

Don't press two or more buttons at the same time, unless you are

specifically instructed to do so in this owner's guide.

Don't allow the remote control to get wet or become heated.

Avoid dropping the remote control on a hard surface.

When cleaning the remote control, don't use any harsh chemicals.

Use only a soft, slightly moistened cloth.

Don't mix new batteries with old ones.

Don't heat, take apart, or throw batteries into a fire.

Use alkaline batteries.

Using the remote control with yourTV

You can use your remote to control the TV, CABLE/DBS,VCR,

DVD or AUDIO. The remote has been preset to operate the

TV and other Mitsubishi products. It can be set to control

other audio/video equipment.

To operate the TV, the select switch at the top of the remote

should be set toTV.

16

I_

C_LE/DB$ VGR DVD

ooo 0

O O 0

Remote Control of Other Audio and Video Products

Programming the Remote to Control OtherAudio andVideo Products:

Move the slide switch at the top of the remote to select the

audio or video product you want to control.

Press and hold the POWER button, so that it stays down when

you enter the code.

Enter the code for the equipment from the appropriate list,

exactly asstated. If there is more than one code number, start

with the first number. After setting the code, release the

POWER button.

Point the remote at the equipment and press the POWER

button. If it is on and turns off or is off and turns on, the

remote will control the equipment. If not, try the next number.

Cable Box codes:

Cable box brand codeto enter: If your

General Instruments/ 111,119, 120, 121,122, cable box

Jerrold 123, 124, 125, 126, 127 code is not

Oak 102, 137, 139 listed here,

please see

Pioneer 101, 116 page 63

Scientific Atlanta 111,112,113 for a

Zenith 100, 117 complete

To reset to default code, enter 000 listing,

Satellite Receiver codes:

VCR

CABLE/DeS DVD

Tv.ll Aoo,o

I M PO RTA NT

If you cannot turn the cable box ON by

pressing POWER, try pressing the

CHANNEL or the number buttons.

Satellite brand

Dishnetwork

Hughes-DSS

RCA-DSS

Sony-DSS 177

Toshiba-DSS 170

Panasonic-DSS 174

Pdmestar 178

To reset to default

codeto enter:

175 "

173

176

code, enter 000

VCR codes:

VCR brand codeto enter:

If your

Mitsubishi 001,002 VCR

Hitachi 020, 043, 065 code is not

JVC 030, 054,059 listed here,

Philips/Magnavox 043,044, 051 please see

Panasonic 041,042, 043 page 64

RCA 020, 053, 065 for a

Sony 048,049, 050 complete

Toshiba 021,066 listing.

TO reset to default code, enter 000

If your

satellite

code is not

listed here

)lease see

page 63

for a

complete

listing,

VCR

CABLE/DBS OVD

VCR

CABLE/DeS

I M PO RTA NT

When set to TV, the PLAY, STOP, REW/

REV and the FF/FWD keys will operate

theVCR after theVCR codes have been

chosen.

17

Remote Control of Other Audio and Video Prod-

uct, continued

DVD Player codes:

DVD/LDP brand

Mitsubishi (DVD)

Mitsubishi (LDP)

Panasonic

Pioneer DVD (LDP)

Sony

Toshiba

codeto enter:

003

016, 017

250

252 (016,017)

254

253

To reset to default code, enter 000

If your

DVD code

is not

listed here,

please see

page 63

for a

complete

listing.

VCR

CABLE/DaS

TV

AV Receiver codes:

Audio brand

Mitsubishi AV receiver

Mitsubishi CD player

Kenwood

Onkyo

Pioneer

Sony

Yamaha

code_ en_r:

010,011,012

013,014,015

200,208

209,214

205,207

222

201,202

To reset to default code, enter 000

If your

Audio

code isnot

listed here,

please see

page 63

for a

complete

listing.

VCR

CABLE/DBS DVD

TV

IMPORTANT

If the slide switch isset toTV when you

enter an AV receiver code,VOLUME and

MUTE will be controlled by theAV receiver.

18

Additional slide switch feature:-for multiple AJV component systems

Your Mitsubishi remote control was designed for flexibility in both large and smallA/V systems.

For example, you can use the slide switch in the following way:

If you have twoVCR's, but no DVD player, move the slide switch to the DVD position and enter

the secondVCR code. Then when the slide switch is moved to DVD you can control the second

VCR.

The following chart shows which device can be entered for each position. Only one device is

allowed for each slide switch position.

TV position:

• TV

• any A/V receiver

(volume, mute only)

Cable/DBS position:

• cable box

• satellite receiver

VCR position: Audio position:

• any VCR • anyAV receiver

• Mitsubishi DVD • Mitsubishi CD player

player • cable box

DVD position:

• any DVD

• any VCR

• cable box

I[ IM PORTANT

/ Some manufacturers may change their products, or they may

J use more than one remote control system. If this isthe case,

your remote_maY -not be able to operate yourVCR, Cable Box,

.................................

Remote Control Functions

Select switch

Selects which AN

wilt be controlled by the

remote

Numbers

To individually select

channels or enter

information into TV

SQV (SuperQuickView TM)

Scan through a memorized list of

favorite channels

Power

power on and off for theTV

or otherAN products

QV (QuickView)

-- Switchesto last channelviewed

INPUT

Selectsthe signalyou will watch (Ant

A; Ant B;Input I, 2 or 3; DVD)

CHANNEL

View channelsin increasingor

decreasingnumerical order

VOLUME

Increasesordecreasessound

©0

SLEEP

Sets theTV to turn off

within 2 hours

VIDEO

Individually adjuststheVideo

settings

AUDIO

Adualtyadjusts

the Audio settings

MUTE

rurnsonoroffthesound

19

Remote Control Functions, continued

ENTER

Use after selecting a

channel number or

menu item

LIGHT

For VS-50705,VS-55705,VS-60705

and VS-70705, press to light up

the remote control

CANCEL

Clear SQV and some

menu entries

PIP or PIP/POP

Useto display,move,

resize or changea PIP

channel.ForVS-50705,

VS-55705,VS-60705and

VS-70705 useto display,

resize or changea POP

channel

ooo 0

OOO

GO0 _

J

ADJUST

Selects menu items.

Moves the PIP

on-screen location

GUIDEFor VS-S0705,VS-SS705,

VS-60705 andVS-70705.

satellite systems program

guides

MENU

Displays on-screen menu

choices

HOME

Exit on-screen menusand

return to TV viewing

INFO

Displays an on-screen

summary of currentTV

settings

REC

Manually record

programs on your VCP_,_

REW/REV

Rewind and reverse search for

theVCR. Skip reverse for CD.

Reverse scan for DVD

PLAY

PlaysaVCR,

N

OOOo

000

000 _

JJJ

STOP

Tostop aVCR, DVD or

PAUSE

_Temporarity stops a

VCR, DVD or CD or

freezes the PIP/POP

FF/FWD

ast forward or forward search

for aVCR. Skip forward for a CD.

Fast play for a DVD

20

Page is loading ...

Mitsubishi VS-55705 Owner's manual

This manual is also suitable for

Mitsubishi VS-55705 Owner's manual

Related papers

Other documents