Philips DVDR3430V/05 User manual

DVD Recorder / VCR

DVDR3430V

DVDR3432V

User Manual

2

Important notes for users in U.K.

Mains plug

This apparatus is  tted with an approved 13

Amp plug. To change a fuse in this type of plug

proceed as follows:

1 Remove fuse cover and fuse.

2 Fix new fuse which should be a BS1362

5 Amp, A.S.T.A. or BSI approved type.

3 Re t the fuse cover.

If the  tted plug is not suitable for your socket

outlets, it should be cut off and an appropriate

plug  tted in its place.

If the mains plug contains a fuse, this should

have a value of 5 Amp. If a plug without a fuse

is used, the fuse at the distribution board

should not be greater than 5 Amp.

Note: The severed plug must be disposed off to

avoid a possible shock hazard should it be

inserted into a 13 Amp socket elsewhere.

How to connect a plug

The wires in the mains lead are coloured with

the following code: blue = neutral (N),

brown = live (L).

z

As these colours may not correspond with the

colour markings identifying the terminals in your

plug, proceed as follows:

– Connect the blue wire to the terminal

marked N or coloured black.

– Connect the brown wire to the terminal

marked L or coloured red.

– Do not connect either wire to the earth

terminal in the plug, marked E (or e) or

coloured green (or green and yellow).

Before replacing the plug cover, make certain

that the cord grip is clamped over the sheath of

the lead - not simply over the two wires.

Copyright in the U.K.

Recording and playback of material may require

consent. See Copyright Act 1956 and The

Performer’s Protection Acts 1958 to 1972.

For Customer Use:

Read carefully the information located at the

bottom or rear of your DVD Recorder and

enter below the Serial No. Retain this

information for future reference.

Model No. DVD/VCR RECORDER

DVDR3430V, DVDR3432V

Serial No. _______________

Norge

Typeskilt  nnes på apparatens underside.

Observer: Nettbryteren er sekundert

innkoplet. Den innebygde netdelen er

derfor ikke frakoplet nettet så lenge

apparatet er tilsluttet nettkontakten.

For å redusere faren for brann eller elektrisk

støt, skal apparatet ikke utsettes for regn eller

fuktighet.

Italia

DICHIARAZIONE DI CONFORMITA’

Si dichiara che l’apparecchio DVDR3430V,

DVDR3432V, Philips risponde alle prescrizioni

dell’art. 2 comma 1 del D.M. 28 Agosto 1995 n.

548.

Fatto a Eindhoven

Philips Consumer Electronics

Philips, Glaslaan 2

5616 JB Eindhoven, The Netherlands

English

3

CAUTION

VISIBLE AND INVISIBLE LASER

RADIATION WHEN OPEN. AVOID

EXPOSURE TO BEAM

ADVARSEL

SYNLIG OG USYNLIG LASERSTRÅLING

VED ÅBNING UNDGÅ UDSÆTTELSE

FOR STRÅLING

VARNING

SYNLIG OCH OSYNLIG

LASERSTRÅLNING NÄR DENNA DEL ÄR

ÖPPNAD BETRAKTA EJ STRÅLEN

VARO!

AVATTAESSA OLET ALTTIINA

NÄKYVÄLLE JA NÄKYMÄTTÖMÄLLE

LASER SÄTEILYLLE. ÄLÄ KATSO

SÄTEESEEN

VORSICHT

SICHTBARE UND UNSICHTBARE

LASERSTRAHLUNG WENN

ABDECKUNG GEÖFFNET NICHT DEM

STRAHL AUSSETZEN

ATTENTION

RAYONNEMENT LASER VISIBLE ET

INVISIBLE EN CAS D’OUVERTURE

EXPOSITION DANGEREUSE AU

FAISCEAU

DK

Advarsel: Usynlig laserstråling ved åbning

når sikkerhedsafbrydere er ude af funktion.

Undgå utsættelse for stråling.

Bemærk: Netafbryderen er sekundært

indkoblet og ofbryder ikke strømmen fra

nettet. Den indbyggede netdel er derfor

tilsluttet til lysnettet så længe netstikket

sidder i stikkontakten.

S

Klass 1 laseraparat

Varning! Om apparaten används på annat

sätt än i denna bruksanvisning speci cerats,

kan användaren utsättas för osynlig

laserstrålning, som överskrider gränsen för

laserklass 1.

Observera! Stömbrytaren är sekundärt

kopplad och bryter inte strömmen från

nätet. Den inbyggda nätdelen är därför

ansluten till elnätet så länge stickproppen

sitter i vägguttaget.

SF

Luokan 1 laserlaite

Varoitus! Laitteen käyttäminen muulla kuin

tässä käyttöohjeessa mainitulla tavalla

saattaa altistaa käyttäjän

turvallisuusluokan 1 ylittävälle

näkymättömälle lasersäteilylle.

Oikeus muutoksiin varataan. Laite ei saa

olla alttiina tippu-ja roiskevedelle.

Huom. Toiminnanvalitsin on kytketty

toisiopuolelle, eikä se kytke laitetta irti

sähköverkosta. Sisäänrakennettu verkko-osa

on kytkettynä sähköverkkoon aina silloin,

kun pistoke on pistorasiassa.

Disposal of your old product

Your product is designed and manufactured with high quality materials

and components, which can be recycled and reused.

When this crossed-out wheeled bin symbol is attached to a product it

means the product is covered by the European Directive 2002/96/EC.

Please inform yourself about the local separate collection system for

electrical and electronic products.

Please act according to your local rules and do not dispose of your old products with

your normal household waste. The correct disposal of your old product will help

prevent potential negative consequences for the environment and human health.

4

English

5

This product incorporates copyright protec-

tion technology that is protected by US

patents. Use of this copyright protection

technology must be authorised by Macrovi-

sion, and is intended for home and other

limited viewing uses only unless otherwise

authorised by Macrovision. Reverse

engineering or disassembly is prohibited.

U.S. Patent Number 4,631,603; 4,819,098;

4,907,093; 5,315,448; and 6,516,132

Manufactured under license from Dolby

Laboratories. “Dolby” and the double-D

symbol are trademarks of Dolby Laboratories.

S

HOWVIEW

®

, VIDEO Plus+ are registered

trademark of Gemstar Development

Corporation. SHOWVIEW

®

is manufactured

under license from Gemstar Development

Corporation.

LASER

Type Semiconductor laser

InGaAlP (DVD)

AIGaAs (CD)

Wave length 658 nm (DVD)

90 nm (CD)

Output Power 30 mW (DVD+RW write)

1.0 mW (DVD read)

1.0 mW (CD read)

Beam divergence 84 degrees (DVD)

61 degrees (CD)

This product complies with the radio

interference requirements of the

European Community.

This product complies with

the requirements of the

following directives and

guidelines: 73/23/EEC +

89/336/EEC + 93/68/EEC

DivX

®

, DivX Certi ed, and associated

logos are trademarks of DivX, Inc. and

are used under license.

English

6

Table of Contents

General

Care and Safety Information ..........................................................................................8

Setup precautions .................................................................................................................................................8

Cleaning discs ........................................................................................................................................................8

About recycling .....................................................................................................................................................8

Product Information ...................................................................................................9-10

In troduc tion ...........................................................................................................................................................9

Accessories supplied ...........................................................................................................................................9

Region codes ..........................................................................................................................................................9

Copyright notice ...................................................................................................................................................9

Product features .................................................................................................................................................10

Possible simultaneous operations .................................................................................................................10

Product Overview

Main Unit ......................................................................................................................... 11

Remote Control ........................................................................................................12-14

Using the remote control ................................................................................................................................14

Connections

Step 1: Basic Recorder Connections .......................................................................15-17

Connecting the antenna cables ......................................................................................................................15

Connecting the video cables ...........................................................................................................................16

Connecting the audio cables ...........................................................................................................................17

Step 2: Optional Connections ..................................................................................18-19

Connecting to a Cable Box or Satellite Receiver .....................................................................................18

Connecting a DV camcorder ..........................................................................................................................19

Connecting another video device ..................................................................................................................19

Step 3: Installation and Setup ................................................................................. 20-22

Finding the correct viewing channel ............................................................................................................ 20

Setting the OSD language ............................................................................................................................... 20

Select the country of your residence ...........................................................................................................21

Setting the TV channel programmes ............................................................................................................21

Setting the date & time .................................................................................................................................... 22

Recording

Recording ................................................................................................................... 23-28

Recording media ................................................................................................................................................ 23

Recording settings ............................................................................................................................................24

RECORD settings ............................................................................................................................................. 25

Recording from various sources ............................................................................................................. 26-27

Instant time-off recording ............................................................................................................................... 28

Watching disc playback during VCR recording ......................................................................................... 28

Watching another source during recording .............................................................................................. 28

Timer Recording ....................................................................................................... 29-32

About timer recording ......................................................................................................................................29

Timer recording (SHOWVIEW

®

/ VIDEO Plus+ System) ..................................................................... 29-30

Timer recording (manually) ......................................................................................................................30-32

Changing/ Deleting a timer recording ..........................................................................................................32

English

7

Table of Contents

Dubbing

Direct Dubbing (Disc î Tape) .....................................................................................33

Dubbing from VCR to DVD ............................................................................................................................33

Dubbing from DVD to VCR ............................................................................................................................33

Playback

DVD Playback ............................................................................................................ 34-38

Playable discs ...................................................................................................................................................... 34

Starting disc playback .................................................................................................................................35-38

Additional Playback Features ................................................................................. 39-42

Changing to another title/chapter/track .....................................................................................................39

Pausing playback .................................................................................................................................................39

Searching forward/backward ..........................................................................................................................39

Using the TOOLS options ........................................................................................................................40-42

VCR Playback ..................................................................................................................43

Starting VCR playback ...................................................................................................................................... 43

Edit Recordings

Edit Recording - Recordable DVD .......................................................................... 44-51

About disc editing ............................................................................................................................................. 44

Accessing disc editing menu .....................................................................................................................44-46

Playing your recordings (DVD±R) on other DVD players .................................................................... 46

About title editing ..............................................................................................................................................47

Accessing title editing menu ..................................................................................................................... 47-48

About video editing ......................................................................................................................................... 49

Accessing video editing menu .................................................................................................................. 49-51

Others

DVD Setup Menu Options ....................................................................................... 52-59

Accessing the Setup Menu ...............................................................................................................................52

GENERAL settings .............................................................................................................................................53

PLAYBACK settings ...................................................................................................................................54-55

DVD settings ................................................................................................................................................55-56

CHANNEL SETUP settings ..................................................................................................................... 57-58

CLOCK settings .................................................................................................................................................59

Other Information ..........................................................................................................60

Installing the latest software .......................................................................................................................... 60

Speci cations .................................................................................................................. 61

Troubleshooting ........................................................................................................ 62- 65

Frequently Asked Questions ................................................................................... 66-67

Glossary ..................................................................................................................... 68-69

Display panel symbols/ messages .................................................................................70

TV System Guide .......................................................................................................71-72

English

8

Care and Safety Information

CAUTION!

High voltage! Do not open the

device. You run the risk of getting

an electric shock.

The machine does not contain any

user-serviceable parts. Please leave

all maintenance work to quali ed

personnel.

Setup precautions

Finding a suitable location

– Place the set on a  at, hard and stable

surface. Do not place the set on a carpet.

– Do not place the set on top of other

equipment that might heat it up (e.g.,

receiver or ampli er).

– Do not put anything above or under

the set (e.g., CDs, magazines).

– Install this unit near the AC outlet and

where the AC power plug can be

reached easily.

Space for ventilation

– Keep the distances 20 cm around

apparatus of ventilation openings. Do

not place the device on an unsteady base.

– The mains plug shall remain readily

operable.

10cm (4.5")

5cm (2.3")

Avoid high temperature, moisture,

water and dust

– Apparatus should not be exposed to

dripping or splashing.

– Do not place any object or items that

can damage the apparatus (e.g., liquid

 lled objects, lighted candles).

Cleaning discs

Some problems occur (frozen picture,

sound disruptions, picture distortions)

because the disc in the apparatus is dirty.

To avoid these problems, discs should be

cleaned on a regular basis.

To clean a disc, use a micro  bre cleaning

cloth and wipe the disc from centre to

the edge in straight line movement.

CAUTION!

Do not use solvents such as benzene,

thinner, commercially available cleaners,

or anti-static sprays for discs.

Since the optical unit (laser) of the

recorder operates at a higher power than

regular DVD or CD players, Cleaning CD

intended for DVD or CD players may

damage the optical unit (laser).

Therefore, refrain from using a Cleaning

CD.

About recycling

These operating instructions have been

printed on non-polluting paper. This

electronic equipment contains a large

number of materials that can be recycled.

If you are disposing off an old equipment,

please take it to a recycling centre. Please

observe the local regulations regarding

disposal of packaging materials, exhausted

batteries and old equipment.

English

9

Introduction

Your Philips DVD recorder comes with a

built-in VCR deck. It allows recording to

DVD±RW, DVD±R, DVD+R DL and

VHS tape. In addition, you can enjoy

playback of DVD discs and VHS tapes.

The DVD±R discs have to be  nalised

before they can be played on other DVD

players.

Before you can start using this recorder,

complete the basic connections and

set-up in three simple steps.

Step 1: Basic recorder connections

Step 2: Optional connections for

other devices

Step 3: Basic installation and

set-up

Please take time to read this user manual

before using your recorder. It contains

important information and notes

regarding operations of the recorder.

Helpful Hints:

– If you have questions or problems occur

during operation, see chapter

‘Troubleshooting’.

– If you need further assistance, please call

the customer support service for your

country. The corresponding telephone

numbers and e-mail addresses are given in

the guarantee booklet.

– Refer to the type plate on the rear or

bottom of the product for identi cation and

supply ratings.

Accessories supplied

– Remote control and batteries

– RF coaxial cable

– Quick Start Guide

Region codes

DVD movies are usually not released at

the same time in all regions of the world,

thus all DVD players are programmed to

a speci c region code.

This device will only play

Region 2 DVDs or DVDs

manufactured to be played in

all regions (‘ALL’). DVDs from

other regions cannot be

played on this recorder.

Copyright notice

The making of unauthorised copies of

copy-protected material, including

computer programmes,  les, broadcasts

and sound recordings, may be an

infringement of copyrights and constitute

a criminal offence. This equipment should

not be used for such purposes.

Product Information

ALL

2

English

10

Product features

This is a simple programming system for

recorders. To use it, enter the

programming number associated with

your television programme. You can  nd

this number in your favourite listings

magazine.

Note: In the UK and Ireland the

ShowView system is called VIDEO Plus+

system and ShowView Programming

Number is called PlusCode Programming

Number.

i.Link is also known as ‘FireWire’ and

‘IEEE1394’. This connection is used for

transferring of high bandwidth digital

signals used by digital video (DV)

camcorders. It carries all audio and video

signals via a single cable.

Philips DVD recorders support ‘dual

media’ recording – the ability to create

recordings on + and - discs

(DVD+R/+RW, DVD+R DL, DVD-R/

-RW).

Direct Dubbing

The built-in VCR deck makes it simple to

copy your recordings from VHS tape to

DVD or from DVD to VHS tape with a

single press of a button.

Product Information (continued)

Possible simultaneous

operations

-

– When you play a DVD disc, only dubbing

from DVD disc to VCR is possible to

operate simultaneously.

– When you record to a DVD recordable

disc, no other operations can be carried

out simultaneously.

– When you play a VHS tape, only dubbing

from VCR to DVD is possible to operate

simultaneously.

– When you record to a VHS tape, only

DVD playback is possible to operate

simultaneously.

Play Record Play Record

DVD VCR

Current

Operation

Play DVD

Record on

DVD

Play VCR

Record on

VCR

English

11

Main Unit

a

STANDBY-ON 1

– Turns on the recorder or to standby

mode.

b

Tape deck

c

EJECT Z

– Ejects the VHS tape.

d

OPEN/CLOSE Z

– Opens/closes the disc tray.

e

Disc tray

f

CHANNEL V v

– While in tuner, selects the next or

previous TV channel.

g

SOURCE

– Selects the recorder’s input source

(EXT1, EXT2, TUNER, CAM1, DV).

h

VCR indicator

– Lights up while in VCR mode.

i

DVD indicator

– Lights up while in DVD mode.

j

DIRECT DUBBING

– Copies from a VHS tape to a recordable

DVD or vice-versa.

k

System display panel

– Shows information about the current

status of the recorder.

l

PLAY/PAUSE u

– Starts playback.

– Pauses the playback/recording/dubbing.

STOP x

– Stops playback/recording.

REW m /

F.FWD M (PREV / NEXT)

– Skips to the previous or next title/

chapter/track.

– Press and hold this button for fast

forward and backward search.

m

REC z

– Start recording the current TV channel

or the current video input source.

– Press repeatedly to set up a One Touch

Recording at 30, 60 or 90 minutes interval.

Sockets behind the  ap

Flip down the door as indicated by the

OPEN B label at the right hand corner.

n

DV IN

– Input for digital camcorder or other

suitable devices using this connector.

o

VIDEO

– Video input for camcorder or video

recorder.

p

AUDIO L/R

– Audio input for camcorder or video

recorder.

English

12

Remote Control

a

2

– Turns on the recorder or to standby

mode.

b

TV/VIDEO

– Switch between playback from additional

devices (connected via EXT2 AUX I/O

socket) and playback from the recorder.

DVD

– Switch to DVD mode.

VCR

– Switch to VCR mode.

c

SOURCE

– Selects the recorder’s input source

(EXT1, EXT2, TUNER, CAM1, DV).

1

2

3

4

5

6

7

8

9

10

11

12

13

14

d

CLEAR

– Clears a track/chapter/ le in the selection

playlist/copylist.

– Clears a timer entry.

– Resets tape counter to zero.

e

SETUP

– Enters/exits the system setup menu.

f

W X : Cursor buttons for moving to the

left or right, do a forward/reverse search.

ST : Cursor buttons for moving

up/down or changing the recorder’s TV

tuner channel.

g

OK

– Stores/con rms an entry.

h

DISPLAY

– Displays/removes the status bar.

i

PREV í/ NEXTë

– Skips to previous or next chapter/track/

index.

j

P +/-

– While in tuner, select the next or

previous TV channel.

– While in VCR mode, adjust the picture

quality (tracking).

k

DIRECT DUBBING

– Copies from a VHS tape to a recordable

DVD or vice-versa.

l

AUDIO

– Selects an audio language (DVD, VCD) or

an audio channel (CD, VHS).

m

SHOWVIEW

– Enters/exits the S

HOWVIEW menu.

VIDEO Plus+ (for UK only)

– Enters/exits the V

IDEO PLUS+ menu.

n

EDIT

– Enters/exits the video editing menu.

English

13

Remote Control (continued)

o

REPEAT

– Selects to repeat playback of title,

chapter, track or disc in DVD mode.

p

TOOLS

– Enters/exits the tools or disc/title editing

menu.

q

SELECT

– Selects a track/chapter/ le in the

programme menu.

r

DISC-MENU

– Accesses DVD disc menu or Index

Picture screen of a DVD±R/±RW.

– Accesses VCD disc menu when PBC is

turned on.

s

BACK2

– Returns to the previous menu of a video

CD (VCD).

t

REW m / FFW M

– Fast reverse or fast forward search.

u

PLAY/PAUSE u

– Starts playback.

– Pauses the playback/recording/dubbing.

REC z

– Start recording the current TV channel

or the current video input source.

– Press repeatedly to set up a One Touch

Recording at 30, 60 or 90 minutes

interval.

STOP



– Stops playback/recording/dubbing.

– Press and hold the button to open/ close

the disc tray.

v

TV VOL +/ -

– Adjusts the volume of the TV (Philips TV

only).

w

Numeric keypad

– Selects a chapter/track number to play.

– Selects the recorder’s preset TV tuner

channel.

x

SUBTITLE

– Selects a DVD subtitle language.

y

REC MODE

– Toggles between recording modes:

HQ, SP, SPP, LP, EP or SLP.

VCR: SP & LP

This determines the quality of recording

and the amount/length of time you can

record on a DVD±R/±RW.

z

TIMER

– Enters/exits the timer recording menu.

16

17

18

24

25

26

23

19

20

21

22

15

English

14

Remote Control (continued)

Using the remote control

A

Open the battery compartment.

B

Insert two batteries type R03 or AAA,

following the indications (+-) inside

the compartment.

C

Close the cover.

D

Point the remote control directly at the

remote sensor (iR) on the front panel.

E

Select the source you wish to control by

pressing the DVD, VCR or SOURCE

button on the remote control.

F

Then select the desired function (for

example m, M).

CAUTION!

– Remove batteries if they are

exhausted or if when the remote

control is not to be used for a long

time.

– Do not mix batteries (old and new

or carbon and alkaline, etc.).

– Batteries contain chemical

substances, so they should be

disposed of properly.

A

C

B

English

15

Step 1: Basic Recorder Connections

Connecting the antenna

cables

These connections enable you to watch

and record TV programmes using the

recorder. If the antenna signal is

connected via Cable Box or Satellite

Receiver, ensure that these devices are

turned on in order to watch or record

the cable programmes.



If you want to connect to a Cable

Box/Satellite Receiver, see the

chapter “Step 2 : Optional Connections

– Connecting to a Cable Box or Satellite

Receiver” for the complete connections

to your TV.

A

Connect the existing Antenna/Satellite

Receiver/Cable TV signal (labelled as RF

OUT or TO TV) to the ANTENNA-IN

socket on the recorder.

B

Use the supplied RF coaxial cable to

connect the TV-OUT socket on the

recorder to the antenna input socket (or

labelled as VHF/UHF RF IN) on your TV.

Helpful Hint:

– Depending on how you have currently

connected your TV channel (directly from an

off-air antenna or Cable box or VCR), you

may have to disconnect some of the cables

before you make the antenna connection.

TIPS: Before making or changing any connections, make sure that all the devices are disconnected

from the power outlet.

~

MAINS

TO TV - I

/

O

EXT1

AUX - I

/

O

EXT2

S-VIDEO

(Y/C)

AUDIO

COMPONENT

VIDEO

R

L

P

R

P

B

Y

AUDIO / VIDEO OUT

AUDIO / VIDEO OUT 1

VIDEO

(

CVBS

)

COAXIAL

DIGITAL AUDIO OUT

ANTENNA

TV

A

B

cable satellite antenna

English

16

TIPS: Before making or changing any connections, make sure that all the devices are disconnected

from the power outlet.

Step 1: Basic Recorder Connections (continued)

Connecting the video cables

This connection enables you to view the

disc playback from the recorder. You

only need to choose one of the options

below to make your video connection.

Option 1: Using a SCART cable



Use a SCART cable (not supplied) to

connect the EXT1 TO TV-I/O socket

on the recorder to the corresponding

SCART input socket on the TV.

Helpful Hints:

– If your TV has several SCART sockets,

select the SCART socket that is suitable for

both video output and video input.

– If your TV displays a selection for the

SCART socket, select ‘VCR’ as the source for

the SCART socket.

– The EXT2 AUX-I/O socket is intended

only for additional devices.

Option 2: Using an S-Video cable



Use an S-video cable (not supplied) to

connect the S-VIDEO OUTPUT

socket on the recorder to the S-Video

input socket (or labelled as Y/C or

S-VHS) on the TV.

 Audio connection is required in order

to hear the sound, see next section

“Connecting the audio cables”.

Option 3: Using a Video (CVBS)

cable



Use a composite video cable (yellow end

- not supplied) to connect the

VIDEO(CVBS) OUTPUT socket on

the recorder to the video input socket

(or labelled as A/V In, Video In,

Composite or Baseband) on the TV.

 Audio connection is required in order

to hear the sound, see next section

“Connecting the audio cables”.

~

MAINS

TO TV - I

/

O

EXT1

AUX - I

/

O

EXT2

S-VIDEO

(Y/C)

AUDIO

COMPONENT

VIDEO

R

L

P

R

P

B

Y

AUDIO / VIDEO OUT

AUDIO / VIDEO OUT 1

VIDEO

(

CVBS

)

COAXIAL

DIGITAL AUDIO OUT

ANTENNA

TV

Option 1

Option 2

Option 3

OR

English

17

Step 1: Basic Recorder Connections (continued)

TIPS: Before making or changing any connections, make sure that all the devices are disconnected

from the power outlet.

Connecting the audio cables

This connection enables you to listen to

the playback from the recorder.

However, this connection is not required

if the recorder is connected to the TV

using the SCART cable.

Option 1: Using an audio cable

You can connect the recorder to a two

channel stereo system (mini system, TV)

or receiver in order to enjoy the stereo

sound system.



Use an audio cable (red/white ends - not

supplied) to connect the AUDIO L/R

OUTPUT sockets to the audio input

sockets of the connected device.

~

MAINS

TO TV - I

/

O

EXT1

AUX - I

/

O

EXT2

S-VIDEO

(Y/C)

AUDIO

COMPONENT

VIDEO

R

L

P

R

P

B

Y

AUDIO / VIDEO OUT

AUDIO / VIDEO OUT 1

VIDEO

(

CVBS

)

COAXIAL

DIGITAL AUDIO OUT

ANTENNA

TV

Option 1

AV ampli er/

receiver

Option 2: Using a coaxial cable

You can connect the recorder to an AV

ampli er/receiver with a digital multi-

channel sound decoder in order to enjoy

multi-channel surround sound.



Use a coaxial cable to connect the

COAXIAL (DIGITAL AUDIO)

socket on the recorder to the digital

input socket on the ampli er/receiver.

Before you start operating, set the digital

audio output settings accordingly (see the

section “DVD Setup Menu Options –

PLAYBACK settings – Digital Audio

Output”).

If the setting does not match your

stereo’s capabilities, the stereo may

produce a strong, distorted sound or no

sound at all.

Option 2

English

18

Step 2: Optional Connections

Connecting to a Cable Box or

Satellite Receiver

Option 1

If your Cable Box/Satellite Receiver

has only an antenna output socket

(RF OUT or TO TV),

see “Step 1: Basic Recorder Connections

– Connecting the antenna cables” for the

complete connections to your TV.

Option 2

If your Cable Box/Satellite Receiver

has a SCART output socket

A

Keep the existing antenna connection

from the Cable Box/Satellite Receiver to

your TV.

B

Use the SCART cable to connect the

EXT1 TO TV-I/O socket on the

recorder to the corresponding SCART

input socket on the TV.

C

Use another SCART cable to connect the

EXT2 AUX-I/O socket on the recorder

to the SCART output socket (or labelled

as TV OUT or TO TV) on the Cable

Box/Satellite Receiver.

To start playback, select the TV channel

directly on the Cable Box/Satellite

Receiver. To view picture from a

connected external device, press the

TV/VIDEO button on the remote

control.

TIPS: Refer to the respective connected device’s user manual for other possible connections.

B

C

~

MAINS

TO TV - I

/

O

EXT1

AUX - I

/

O

EXT2

S-VIDEO

(Y/C)

AUDIO

COMPONENT

VIDEO

R

L

P

R

P

B

Y

AUDIO / VIDEO OUT

AUDIO / VIDEO OUT 1

VIDEO

(

CVBS

)

COAXIAL

DIGITAL AUDIO OUT

ANTENNA

TV

Rear of a Cable Box

or Satellite Receiver

(Example only)

cable

satellite

antenna

A

English

19

TIPS: Refer to the respective connected device’s user manual for other possible connections.

Step 2: Optional Connections (continued)

Connecting a DV camcorder

Use this if you have a Digital Video or

Digital 8 camcorder. The DV socket

conforms to the i.LINK standard.



Use an i.LINK 4-pin cable (not supplied)

to connect the DV IN socket at the

front panel of the recorder to the

appropriate DV OUT socket on the

camcorder.

Before you start operating, press

SOURCE on the remote control

repeatedly to select ‘DV’ as the input

channel.

Helpful hints:

– The DV IN socket does not support

connection to a Personal Computer.

– It is NOT possible to record from the

recorder to your camcorder via the DV IN

socket on your recorder.

Connecting another video

device

You can use the front sockets connection

to copy the playback from another video

device (for example, camcorder, VCR or

DVD player).

A

Use a video cable (not supplied) to

connect the VIDEO socket from the

front panel of the recorder to the Video

output socket of the connected video

device.

B

Use an audio cable (not supplied) to

connect the AUDIO L/R sockets to the

audio output sockets of the connected

video device.

Before you start operating, press

SOURCE on the remote control

repeatedly to select ‘CAM 1’ as the input

channel.

A

B

English

20

Step 3: Installation and Setup

Before you start...

When you completed the

connections and turn on the

recorder for the  rst time, it is

advisable that you perform several

basic settings.

Please see the following pages on using

the system setup menu features to

programme TV channels, menu language

and system clock settings. This will

optimise the performance of this

recorder.

Finding the correct viewing

channel

A

Press STANDBY-ON on the recorder

to turn it on.

B

Turn on the TV and set it to the correct

video-in channel. You should see the blue

DVD background screen.

 You may go to Channel 1 of your TV,

then press the Channel Down button on

your TV’s remote control until you see

the Video In channel.

 You may press ° button repeatedly

on your TV’s remote control.

 Usually this channel is between the

lowest and highest channels and may be

called FRONT, A/V IN, VIDEO. See your

TV manual for more details.

Setting the OSD language

Select the menu language for this

recorder’s on-screen display. The

language options are different depending

on your country or region. It may not

correspond to the illustrations shown on

the user manual.

Language settings can only be

changed when the disc stops playing

or there is no disc in the disc tray.

SETUP

OK

A

Press SETUP.

 The system setup menu appears on

the TV.

B

Use ST keys to highlight

{ Setup Menu - General } and press X

to access the menu.

Countr

y

On Screen Dis

p

la

y

Lan

g

ua

ge

Screen Save

r

Reset Menu Settin

g

s

Setu

p

Menu - Genera

l

German

y

En

g

lis

h

On

OK

C

Use ST keys to highlight { On Screen

Display Language } and press OK to

access its options.

D

Use ST keys to highlight the desired

language and press OK to con rm.

TIPS: Press X to access the options of an item in the menu.

Press SETUP to exit the menu.

Page is loading ...

Philips DVDR3430V/05 User manual

This manual is also suitable for

Philips DVDR3430V/05 User manual

Related papers

Other documents