Chief PAC253 Installation guide

PAC253
Chief
Brand
Chief
Model
PAC253
Category
Wall & ceiling mounts accessories
Type
Installation guide

Chief PAC253 is a CPU holder designed to mount a CPU to a display or interface bracket. It can support a CPU weighing up to 17 lbs (7.7 kg) and allows for easy access to the CPU's ports and controls. The PAC253 comes with mounting buttons, a locking flag, and cable ties for easy installation and cable management. It is compatible with Chief mounts and can be used in various applications, including offices, classrooms, and home entertainment setups.

Chief PAC253 is a CPU holder designed to mount a CPU to a display or interface bracket. It can support a CPU weighing up to 17 lbs (7.7 kg) and allows for easy access to the CPU's ports and controls. The PAC253 comes with mounting buttons, a locking flag, and cable ties for easy installation and cable management. It is compatible with Chief mounts and can be used in various applications, including offices, classrooms, and home entertainment setups.

INSTALLATION INSTRUCTIONS
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
CPU Holder
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
PAC253
PAC253 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT WARNINGS AND
CAUTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component. The wall to which the mount is being attached
may have a maximum drywall thickness of 5/8" (1.6cm).
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located between the CPU Accessory and the
display does not exceed the weight limits for the specific wall
mount being used. The CPU Accessory weighs 17 lbs
(7.7 kg) which needs to be included in this combined weight
total.
DIMENSIONS
MEASUREMENTS: [MILLIMETERS]
INCHES
Installation Instructions PAC253
3
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
PAC253 Installation Instructions
4
TOOLS REQUIRED FOR INSTALLATION
PARTS
#2
1/8"
(included)
1/4"
G (1)
1/8"
A (1)
[CPU Holder]
B (1)
[Faceplate]
C (1)
[Locking Flag]
D (4)
[Mounting Button]
E (4)
[Cable Tie]
F (6)
[Hook and Loop]
H (1)
10-24 x 1/2"
J (4)
10-24 x 1/2"
K (6)
10-24 x 3/8"
L (1)
10-24
M (1)
.194x.375x.032
Installation Instructions PAC253
5
ASSEMBLY
Assembling CPU Accessory
Attaching Locking Flag
1. Attach locking flag (C) to faceplate (B) using one
10-24 x 1/2" Phillips undercut machine screw (H), one
spacer (M), and one 10-24 Nylock lock nut (L).
(See Figure 1)
NOTE: The locking flag may be installed in one of two
locations, dependent upon the display mounting
pattern. (See Figure 1)
Figure 1
Attaching Mounting Buttons
1. Attach four mounting buttons (D) to CPU holder (A) using
four 10-24 x 1/2" flat head cap screws (J). (See Figure 2)
Figure 2
Placing CPU in CPU Holder
1. Put hook and loop tabs (F) together so there are 3 squares
of hook and loop.
2. Remove paper from one side of each of the three hook and
loop squares.
3. Attach hook and loop squares to the CPU. (See Figure 3)
Figure 3
4. Remove paper from hook and loop squares, and press the
CPU against the CPU holder (A).
Locking flag may be
installed in either
location noted.
1
(H) x 1
(C)
(M)
(L)
(B)
1
(J) x 4
(D) x 4
(A)
3
(F) x 3
4
CPU
(A)
PAC253 Installation Instructions
6
Attaching Faceplate to CPU Box
1. Attach faceplate (B) to CPU box (A) using six 10-24 x 3/8"
button head cap screws (K). (See Figure 4)
Figure 4
INSTALLATION
Installing CPU Holder with CPU to Mount
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located between the CPU Accessory and the
display does not exceed the weight limits for the specific wall
mount being used. The CPU Accessory weighs 17 lbs
(7.7 kg) which needs to be included in this combined weight
total.
Install the CPU holder, with CPU, onto mount and route wires
and cables following the instructions provided with the mount.
Cable ties (E) are provided for cable management.
WARNING: IMPROPER INSTALLATION CAN LEAD TO
CPU HOLDER FALLING! Make certain mounting buttons on
CPU holder are fully engaged in teardrop holes in mount and
latching flag on mount is fully closed before installing the
display.
Installing Display
WARNING: DISPLAY MAY WEIGH IN EXCESS OF 40
LBS. ALWAYS use two people when lifting and follow proper
lifting techniques when installing!
IMPORTANT ! : The following procedure assumes that
the proper interface bracket for display being mounted
has already been installed on display. If no interface
bracket is present on display, install bracket to display
using instructions included with interface bracket before
proceeding.
To install the display:
1. Ensure that locking flag is in open position. (See Figure 5)
2. While supporting each side of display, align four mounting
buttons on display or interface bracket with four teardrop
slots in CPU holder (See Figure 5).
3. Lower display firmly into place. (See Figure 5)
Figure 5
4. Ensure mounting buttons are fully seated in teardrop slots.
5. Close locking flag.
6. Connect cables to display.
(K) x 6
1
Mounting Button
(On interface bracket or display)
3
(A)
1
2
Installation Instructions PAC253
7
PAC253 Installation Instructions
USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378
P 800.582.6480 / 952.894.6280
F 877.894.6918 / 952.894.6918
Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
P +31 (0)40 2668620
F +31 (0)40 2668615
Asia Pacific A Room 24F, Block D, Lily YinDu International Building
LuoGang, BuJi Town, Shenzhen, CHINA.
P +86-755-8996 9226
F +86-755-8996 9217
Chief Manufacturing, a products division
of Milestone AV Technologies
8832-002017 Rev00
2009 Milestone AV Technologies, a
Duchossois Group Company
www.chiefmfg.com
07/09
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Chief PAC253 Installation guide

PAC253
Chief
Brand
Chief
Model
PAC253
Category
Wall & ceiling mounts accessories
Type
Installation guide

Chief PAC253 is a CPU holder designed to mount a CPU to a display or interface bracket. It can support a CPU weighing up to 17 lbs (7.7 kg) and allows for easy access to the CPU's ports and controls. The PAC253 comes with mounting buttons, a locking flag, and cable ties for easy installation and cable management. It is compatible with Chief mounts and can be used in various applications, including offices, classrooms, and home entertainment setups.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents