Chauvet EZrail RGBA Reference guide

Quick Reference Guide

EZrail™ RGBA QRG EN

2

About This

Guide

The EZrail™ RGBA

Quick Reference Guide (QRG) has basic product

information such as mounting, menu options, and DMX values. Download

the User Manual from www.chauvetlighting.com for more details.

Disclaimer

The information and specifications contained in this QRG are subject to

change without notice.

Safety Notes

These Safety Notes include important information about installation, use,

and maintenance.

• This product is not intended for permanent installation.

• ONLY connect this product to a grounded and protected circuit.

• Always disconnect from power before cleaning or replacing the fuse.

• DO NOT look at the light source when the product is on.

• Make sure the power cord is not crimped or damaged.

• Never disconnect this product from power by pulling on the cord.

• When mounting this product overhead, use a safety cable.

•

DO NOT allow flammable materials close to the unit while operating.

• DO NOT touch this product when it is operating because it may be hot.

• The voltage of the outlet to which you are connecting this product must

be within the range stated on the decal or rear panel of the product.

• This product is for indoor use only! (IP20) To prevent risk of fire or

shock, do not expose this product to rain or moisture.

• Always mount this product in a location with adequate ventilation, at

least 20 in (50 cm) from adjacent surfaces.

• Be sure that no ventilation slots on the unit’s housing are blocked.

• Never connect this product to a dimmer or rheostat.

• Replace the fuse with one of the same type and rating.

• ONLY use the hanging/mounting bracket to carry this product.

• The maximum ambient temperature is 104° F (40° C). Do not operate

this product at higher temperatures.

• In the event of a serious operating problem, stop using immediately.

•

DO NOT open this product. It contains no user-serviceable parts.

Contact

Outside the U.S., United Kingdom, or Ireland, contact your distributor to

request support or return a product. Visit www.chauvetlighting.com

for

contact information.

What Is

Included

• EZrail™ RGBA

• Infrared Remote Control (IRC)

• Hanging Bracket and Mounting

Hardware

• Power Cord

• Warranty Card

• Quick Reference Guide

To Begin

Unpack your EZrail™ RGBA and make sure you have received all parts in

good condition. If the box or contents appear damaged, notify the carrier

immediately, not CHAUVET®.

EN EZrail™ RGBA QRG

3

Description

The EZrail™ RGBA is a

linear RGBA fixture with a rechargeable lithium

battery. Control options include Sound-Active mode, automa

tic programs,

Master/Slave mode, DMX, and included Infrared Remote Control (IRC). Six

personality choices are available through 2-, 4-, 5-, 8-, 10- and 18-

channel DMX

modes.

Overview

AC Power

This product has an auto-ranging power supply that can work with an input

voltage range of 100~240 VAC, 50/60 Hz.

Power Linking

You can link up to 32 EZrail™ RGBA products at 120 VAC and 64 units at

230 VAC.

Fuse

Replacement

1. Disconnect the product from power.

2. Wedge the tip of a flat-head screwdriver into the slot of the fuse holder.

3. Pry the safety cap out of the housing.

4. Remove the blown fuse from the clip on the front of the safety cap and

replace with a fuse of the exact same type and rating.

5. Re-insert the fuse holder and reconnect power.

Charging the

Battery

The EZrail™ RGBA comes with a rechargeable lithium battery for cable-free

operation. To charge the battery, simply plug in the power cord at any time

before, during, or after operation. To charge the battery before or after operation

with all the LEDs off, leave the power switch in the Off postion.

The red

indicator light for the battery turns on while the battery is charging.

The green

indicator light turns on when the battery is done charging.

Battery Life

Indicator

The battery life indicator shows the remaining a

mount of internal battery life

when the the menu buttons are inactive.

100%

75%

50%

25%

Infrared Remote

Control (IRC)

The EZrail™

RGBA is fully compatible with the Infrared Remote Control

(IRC) from CHAUVET®. For more information on the IRC or to download

instructions, go to www.chauvetlighting.com.

Back Panel View

Power Out

Power In

Fuse Holder

Display

DMX Out

DMX In

Safety Loop

Control Buttons

Power

Switch

Microphone

Battery Charged

Green Indicator Light

Battery Charging

Red Indicator Light

EZrail™ RGBA QRG EN

4

Mounting

Before mounting this product, read the Safety Notes.

Mounting

Diagram

Control Panel

Description

Button

Function

<MENU>

Exits from the current menu or function

<UP>

Navigates upwards through the menu list and increases

the numeric value when in a function

<DOWN>

Navigates downwards through the menu list and

decreases the numeric value when in a function

<ENTER>

Enables the currently displayed menu or sets the currently

selected value into the selected function

Bracket AdjustmentKnobs

Mounting Clamp

Safety Cable

Hanging/Mounting

Bracket

Floor Mount

(2x)

EN EZrail™ RGBA QRG

5

Menu Options

Mode

Programming Steps

Description

2-CH

d 1–d512

(Starting Address)

2-channel DMX mode

4-CH

4-channel DMX mode

5-CH

5-channel DMX mode

8-CH

8-channel DMX mode

10CH

10-channel DMX mode

18CH

18-channel DMX mode

SLAv

Slave mode

SU_ _

SU 0–SU31

Sound sensitivity control

Colr

r 0–r255

Red (0–100%)

g 0–g255

Green (0–100%)

b 0–b255

Blue (0–100%)

A 0–A255

Amber (0–100%)

-ir-

IRC functionality

Pr _ _

(Preset Programs)

Pr 1–Pr17

SP 1–SP99, SPFL

Run speed (slow to fast)

Fd 0–Fd99

Dimmer speed (slow to fast)

FS 0–FS99

Strobe speed (slow to fast)

1_ _ _

Background color

(only available in Pr16 and Pr17)

2_ _ _

Front color

(only available in Pr16 and Pr17)

AUTO

(Auto Program)

n 1–n100

Number of loops

SP 1–SP99, SPFL

Run speed (slow to fast)

Fd 0–Fd99

Dimmer speed (slow to fast)

FS 0–FS99

Strobe speed (slow to fast)

EZrail™ RGBA Sections for DMX Control

1

2

3 4

EZrail™ RGBA QRG EN

6

DMX Linking

The EZrail™ RGBA can work with a DMX controller when linked by DMX

serial connections. Instructions for connecting and configuring this product

for DMX operation are in the User Manual. If you are not familiar with

DMX, download the DMX Primer from www.chauvetlighting.com.

Starting Address

To ensure full access to all channels in each DMX mode, the highest

recommended DMX address is 495.

Master/Slave

Connection

The EZrail™ RGBA uses the DMX data connection for its Master/Slave

mode. Instructions for connecting and configuring this product for

Master/Slave operation are in the User Manual.

DMX Values

18-CH

Channel Function Value

Percent/Setting

Section

1

Dimmer

000 ó 255

0–100%

2

Red

000 ó 255

0–100%

1

3

Green

000 ó 255

0–100%

4

Blue

000 ó 255

0–100%

5

Amber

000 ó 255

0–100%

6

Red

000 ó 255

0–100%

2

7

Green

000 ó 255

0–100%

8

Blue

000 ó 255

0–100%

9

Amber

000 ó 255

0–100%

10

Red

000 ó 255

0–100%

3

11

Green

000 ó 255

0–100%

12

Blue

000 ó 255

0–100%

13

Amber

000 ó 255

0–100%

14

Red

000 ó 255

0–100%

4

15

Green

000 ó 255

0–100%

16

Blue

000 ó 255

0–100%

17

Amber

000 ó 255

0–100%

18

Shutter

000 ó 255

0–100%

10-CH

Channel Function Value

Percent/Setting

Section

1

Dimmer

000 ó 255

0–100%

2

Red

000 ó 255

0–100%

1 + 2

3

Green

000 ó 255

0–100%

4

Blue

000 ó 255

0–100%

5

Amber

000 ó 255

0–100%

6

Red

000 ó 255

0–100%

3 + 4

7

Green

000 ó 255

0–100%

8

Blue

000 ó 255

0–100%

9

Amber

000 ó 255

0–100%

10

Shutter

000 ó 255

0–100%

EN EZrail™ RGBA QRG

7

DMX Values (cont.)

8-CH

Channel Function Value Percent/Setting

1

Dimmer

000 ó 255

0–100%

2

Red

000 ó 255

0–100%

3

Green

000 ó 255

0–100%

4

Blue

000 ó 255

0–100%

5

Amber

000 ó 255

0–100%

6 Auto Programs

000 ó 007

No Function

008 ó 015

Red

016 ó 023

Green

024 ó 031

Blue

032 ó 039

Amber

040 ó 047

Cyan

048 ó 055

Magenta

056 ó 063

Yellow

064 ó 071

White (RGB)

072 ó 079

Red + Amber

080 ó 087

Green + Amber

088 ó 095

Blue + Amber

096 ó 103

Red + Green + Amber

104 ó 111

Red + Blue + Amber

112 ó 119

Green + Blue + Amber

120 ó 127

White (RGBA)

128 ó 135

Auto Program 1

136 ó 143

Auto Program 2

144 ó 151

Auto Program 3

152 ó 159

Auto Program 4

160 ó 167

Auto Program 5

168 ó 175

Auto Program 6

176 ó 183

Auto Program 7

184 ó 191

Auto Program 8

192 ó 199

Auto Program 9

200 ó 207

Auto Program 10

208 ó 215

Auto Program 11

216 ó 223

Auto Program 12

224 ó 231

Auto Program 13

232 ó 239

Auto Program 14

240 ó 247

Auto Program 15

248 ó 255

Sound-Active mode

7 Speed/Sensitivity 000 ó 255

Auto programs speed

(when Auto Programs is between 128–247)

Sound sensitivity

(when Auto Programs is between 248–255)

8

Shutter

000 ó 255

0–100%

EZrail™ RGBA QRG EN

8

DMX Values (cont.)

5-CH

Channel Function Value

Percent/Setting

1

Dimmer

000 ó 255

0–100%

2

Red

000 ó 255

0–100%

3

Green

000 ó 255

0–100%

4

Blue

000 ó 255

0–100%

5

Amber

000 ó 255

0–100%

4-CH

Channel Function Value

Percent/Setting

1

Red

000 ó 255

0–100%

2

Green

000 ó 255

0–100%

3

Blue

000 ó 255

0–100%

4

Amber

000 ó 255

0–100%

EN EZrail™ RGBA QRG

9

DMX Values (cont.)

2-CH

Channel Function Value Percent/Setting

1 Auto Programs

000 ó 007

No Function

008 ó 015

Red

016 ó 023

Green

024 ó 031

Blue

032 ó 039

Amber

040 ó 047

Cyan

048 ó 055

Magenta

056 ó 063

Yellow

064 ó 071

White (RGB)

072 ó 079

Red + Amber

080 ó 087

Green + Amber

088 ó 095

Blue + Amber

096 ó 103

Red + Green + Amber

104 ó 111

Red + Blue + Amber

112 ó 119

Green + Blue + Amber

120 ó 127

White (RGBA)

128 ó 135

Auto Program 1

136 ó 143

Auto Program 2

144 ó 151

Auto Program 3

152 ó 159

Auto Program 4

160 ó 167

Auto Program 5

168 ó 175

Auto Program 6

176 ó 183

Auto Program 7

184 ó 191

Auto Program 8

192 ó 199

Auto Program 9

200 ó 207

Auto Program 10

208 ó 215

Auto Program 11

216 ó 223

Auto Program 12

224 ó 231

Auto Program 13

232 ó 239

Auto Program 14

240 ó 247

Auto Program 15

248 ó 255

Sound-Active mode

2 Speed/Sensitivity 000 ó 255

Auto programs speed

(when Auto Programs is between 128–247)

Sound sensitivity

(when Auto Programs is between 248–255)

Page is loading ...

EZrail™ RGBA QRG Multi-Language

68

Значения DMX (прод.)

5-CH

Канал Функция Значение

Процент/уставка

1

Диммер

000 ó 255

0–100%

2

Красный

000 ó 255

0–100%

3

Зеленый

000 ó 255

0–100%

4

Синий

000 ó 255

0–100%

5

Янтарный

000 ó 255

0–100%

4-CH

Канал Функция Значение

Процент/уставка

1

Красный

000 ó 255

0–100%

2

Зеленый

000 ó 255

0–100%

3

Синий

000 ó 255

0–100%

4

Янтарный

000 ó 255

0–100%

Contact Us

World Headquarters

CHAUVET®

General Information

Address: 5200 NW 108th Avenue

Sunrise, FL 33351

Voice: 954-577-4455

Fax: 954-929-5560

Toll free: 800-762-1084

United Kingdom and Ireland

CHAUVET® Europe Ltd.

General Information

Address: Unit 1C

Brookhill Road Industrial Estate

Pinxton, Nottingham, UK

NG16 6NT

Voice: +44 (0)1773 511115

Fax: +44 (0)1773 511110

U.S. Technical Support

Voice: 954-577-4455 (Press 4)

Fax: (954) 756-8015

Email: tech@chauvetlighting.com

U.K. Technical Support

Email: uktech@chauvetlighting.com

World Wide Web

www.chauvetlighting.com

World Wide Web

www.chauvetlighting.co.uk

EZrail™ RGBA

QRG – Rev. 3 ML

Printed in the P. R. C.

Chauvet EZrail RGBA Reference guide

Chauvet EZrail RGBA Reference guide

in other languages

Related papers

Other documents