Chauvet Freedom Strip Mini RGBA User manual

Page is loading ...

Page 2 of 88 Freedom™ Par RGBA and Strip Mini RGBA User Manual Rev. 4

TABLE OF CONTENTS

1. Before You Begin ...........................................................................................................6

What Is Included ......................................................................................................................... 6

Unpacking Instructions ................................................................................................................ 6

Claims ................................................................................................................................................. 6

Text Conventions ........................................................................................................................ 6

Symbols ...................................................................................................................................... 6

Disclaimer ................................................................................................................................... 6

Product at a Glance ..................................................................................................................... 7

Safety Notes ............................................................................................................................... 7

2. Introduction ....................................................................................................................8

Overview (Freedom™ Par RGBA) ............................................................................................... 8

Overview (Freedom™ Par RGBA) ............................................................................................... 9

Overview (Freedom™ Strip Mini RGBA) .................................................................................... 10

Dimensions (Freedom™ Par RGBA) ......................................................................................... 11

Dimensions (Freedom™ Strip Mini RGBA) ................................................................................ 12

3. Setup .............................................................................................................................13

AC Power .................................................................................................................................. 13

Charging the Battery ................................................................................................................. 13

Battery Life Indicator ................................................................................................................. 13

Battery Maintenance .......................................................................................................................... 13

Fuse Replacement ............................................................................................................................. 14

Power Linking .................................................................................................................................... 15

Mounting ................................................................................................................................... 16

Orientation ......................................................................................................................................... 16

Rigging .............................................................................................................................................. 16

4. Operation ......................................................................................................................17

Control Panel Operation ............................................................................................................ 17

Menu Map ................................................................................................................................. 17

Configuration (DMX) .................................................................................................................. 18

Starting Address ................................................................................................................................ 18

DMX Personalities.............................................................................................................................. 18

DMX Channel Modes, Assignments, and Values ....................................................................... 19

5-CH .................................................................................................................................................. 19

4-CH .................................................................................................................................................. 19

Configuration (Standalone) ........................................................................................................ 20

Automatic ACt Mode .......................................................................................................................... 20

ACt Auto Programs ............................................................................................................................ 21

Automatic ACtC Mode ........................................................................................................................ 22

ACtC Auto Programs .......................................................................................................................... 22

IRC (Infrared Remote Control) ............................................................................................................ 23

IRC Operation .................................................................................................................................... 23

IRC Operation (cont.) ......................................................................................................................... 24

D-Fi™ 2.4 GHz (DMX Mode Auto Sync).............................................................................................. 25

D-Fi™ 2.4 GHz (DMX Mode Manual Sync) ......................................................................................... 26

D-Fi™ 2.4 GHz (IR/Standalone Mode Auto Sync) ............................................................................... 27

D-Fi™ 2.4 GHz (IR/Standalone Mode Manual Sync) ........................................................................... 28

Master/Slave Mode ............................................................................................................................ 29

Master/Slave Runway Effect ............................................................................................................... 29

5. Technical Information ..................................................................................................30

Product Maintenance ................................................................................................................ 30

Page is loading ...

Freedom™ Par RGBA and Strip Mini RGBA User Manual Rev. 4 Page 5 of 88

6. Spécificités Techniques ...............................................................................................86

Renvois ..................................................................................................................................... 87

Nous Contacter ......................................................................................................................... 87

Page 6 of 88 Freedom™ Par RGBA and Strip Mini RGBA User Manual Rev. 4

1. BEFORE YOU BEGIN

What Is

Included

• Freedom™ Par RGBA

or

• Freedom™ Strip Mini RGBA

• Power Cord

• Warranty Card

• User Manual

Unpacking

Instructions

Carefully unpack the product immediately and check the box to make sure all the parts

are in the package and are in good condition.

Claims

If the box or the contents (the product and

included accessories) appear damaged from

shipping, or show signs of mishandling, notify the carrier immediately, not CHAUVET®.

Failure to report damage to the carrier immediately may invalidate your claim. In

addition, keep the box and contents for inspection.

For other issues, such as

missing components or parts, damage not related to shipping,

or concealed damage, file a claim with CHAUVET® within 7 days of delivery.

Text

Conventions

Convention

Meaning

1–512

A range of values

50/60

A set of values of which only one can be chosen

Settings

A menu option not to be modified

Menu > Settings

A sequence of menu options to be followed

<ENTER>

A key to be pressed on the product’s control panel

ON

A value to be entered or selected

Symbols

Symbol Meaning

Critical installation, configuration, or operation information. Not

following these instructions may make the product not work, cause

damage to the product, or cause harm to the operator.

Important installation or configuration information. The product

may not function correctly if this information is not used.

Useful information.

Disclaimer

The information and specifications contained in this User Manual

are subject to change

without notice. CHAUVET® assumes no responsibility or liabil

ity for any errors or

omissions, and reserves the right to revise or recreate this manual at any time.

Download the latest version from

www.chauvetlighting.com.

Printed in P.R.C.

Electronically published by CHAUVET® in the United States of America.

Author

Date

Editor

Date

A. Leon 04/11/13 D. Couppe 04/12/13

Freedom™ Par RGBA and Strip Mini RGBA User Manual Rev. 4 Page 7 of 88

Product at a

Glance

Use on Dimmer

x

Auto Programs

P

Outdoor Use

x

Auto-ranging Power Supply

P

Sound-Activated

P

Replaceable Fuse

P

DMX

P

User-Serviceable

x

Master/Slave

P

Duty Cycle

x

Safety Notes

These notes include important information about the mounting, usage, and maintenance

of this product; read before using the product.

• Always connect the product to a grounded circuit to avoid the risk of electrocution.

• Always disconnect the product from the power source before cleaning or replacing

the fuse.

• Avoid direct eye exposure to the light source while the product is on.

• Make sure the power cord is not crimped or damaged.

• Never disconnect the product from power by pulling or tugging on the cord.

• If mounting the product overhead, always secure to a fastening device using a

safety cable.

• Make sure there are no flammable materials close to the product when operating.

• Do not touch the product’s housing when operating because it may be very hot.

• Always make sure that the voltage of the outlet to which you are connecting the

product is within the range stated on the decal or bottom panel of the product.

• The product is for indoor use only! (IP20) To prevent risk of fire or shock, do not

expose the product to rain or moisture.

• Always install the product in a location with adequate ventilation, at least

20 in (50 cm) from adjacent surfaces.

• Be sure that no ventilation slots on the product’s housing are blocked.

• Never connect the product to a dimmer.

• Make sure to replace the fuse with another of the same type and rating.

• Never carry the product from the power cord or any moving part. Always use the

hanging/mounting bracket.

• The maximum ambient temperature (Ta) is 104° F (40° C). Do not operate the

product at higher temperatures.

• In the event of a serious operating problem, stop using the product immediately.

• Never try to repair the product. Repairs carried out by unskilled people can lead to

damage or malfunction. Contact the nearest authorized technical assistance center.

• This product is not intended for permanent installation.

• Keep this User Manual for future use. If you sell the product to another user, be

sure to give this document to the next owner.

The Freedom™ RGBA series products contain rechargeable batteries. These

batteries contain hazardous chemicals that cannot be discarded with household

waste. Contact your local waste management service for recycling information

when disposing of your product.

Page 8 of 88 Freedom™ Par RGBA and Strip Mini RGBA User Manual Rev. 4

2. INTRODUCTION

Overview (Freedom™ Par RGBA)

Front Panel View

On/Off Switch

Battery Life Indicator

Power/Signal

Indicator Lights

Microphone

LED Display/

Control Panel

D-Fi™ AUTO

Sync/Clear Button

Freedom™ Par RGBA and Strip Mini RGBA User Manual Rev. 4 Page 9 of 88

Overview (Freedom™ Par RGBA)

Safety Loop

Master/Slave Link Output

DMX In

DMX Out

Fuse Holder

Power In

Power Out

Back Panel View

Page 10 of 88 Freedom™ Par RGBA and Strip Mini RGBA User Manual Rev. 4

Overview (Freedom™ Strip Mini RGBA)

Back Panel View

Safety Loop

Antenna

Battery Life Indicator

Microphone

On/Off Switch

LED Display

and

Control Panel

D-Fi™ AUTO

Sync/Clear Button

Fuse Holder

Power In

Power Out

Master/Slave Link Output

DMX In

DMX Out

Power/Signal

Indicator Lights

Freedom™ Par RGBA and Strip Mini RGBA User Manual Rev. 4 Page 11 of 88

Dimensions (Freedom™ Par RGBA)

8.5 in

215 mm

9.3 in

236 mm

8.8 in

223 mm

Page 12 of 88 Freedom™ Par RGBA and Strip Mini RGBA User Manual Rev. 4

Dimensions (Freedom™ Strip Mini RGBA)

8.3 in

210 mm

20.0 in

510 mm

3.0 in

78 mm

Freedom™ Par RGBA and Strip Mini RGBA User Manual Rev. 4 Page 13 of 88

3. SETUP

AC Power

The Freedom™ RGBA series has an auto-

ranging power supply and it can work with an

input voltage range of 100~240 VAC, 50/60 Hz.

To determine the product’s power requirements (circuit breaker, power outlet, and

wiring), use the current value listed on the label affixed to the product’s bottom panel, or

refer to the product’s specifications chart. The listed current rating indicates the

product’s average current draw under normal conditions.

Always connect the product to a protected circuit (circuit breaker or fuse). Make

sure the product has an appropriate electrical ground to avoid the risk of

electrocution or fire.

Never connect the product to

a rheostat (variable resistor) or dimmer circuit, even

if the rheostat or dimmer channel serves only as a 0–100% switch.

Charging the

Battery

The Freedom™ RGBA series comes with a non-user-serviceable lithium-

ion battery for

cable-free operation.

To charge the Freedom™ RGBA

series battery, plug in the power cord at any time

before, during, or after operation. To charge the battery before or after operation with all

the LEDs off, leave the power switch in the Off position.

Battery Life

Indicator

The

battery life indicator located on the product displays the remaining amount of

internal battery life. Use the chart below to find out how much battery life remains per

charge cycle. The light to the far right flashes during charging.

The Freedom™ RGBA

series battery should be charged 24 hours prior to initial

use for optimal battery life.

Battery

Maintenance

To keep the battery in optimal operating condition, store the product in a cool, dry place

and charge at least once every 30 days when not in use.

Avoid exposure to extreme temperatures. If the product is exposed to extreme cold or

hot temperatures, warm up/cool down the product before use and before charging.

Run-Time Table

Maximum Run Time Recharge Time

Up to 8 hours 6 hours

Page 14 of 88 Freedom™ Par RGBA and Strip Mini RGBA User Manual Rev. 4

Fuse

Replacement

Disconnect the product from power before replacing the fuse.

1. Disconnect the product from power.

2. Wedge the tip of a flat-head screwdriver into the slot of the fuse holder.

3. Pry the fuse holder out of the housing.

4. Remove the blown fuse from the holder.

5. Replace with a fuse of the exact same type and rating.

6. Insert the fuse holder back in place and reconnect power.

A spare fuse is not included; however, the safety cap has room for a spare.

Always replace a blown fuse with one of the same type and rating.

Installed fuse

(held by plastic clip)

Spare fuse holder

(inside safety cap)

Safety cap

Freedom™ Par RGBA and Strip Mini RGBA User Manual Rev. 4 Page 15 of 88

Power Linking

The product provides power linking via the IEC outlet located in the back of the unit.

Power Linking

Diagram

You can power link up to 16 Freedom™ Par RGBA unit

s on 120 VAC or up

to 25 Freedom™ Par RGBA units on 230 VAC.

You can power link up to 16 Freedom™ Strip Mini RGBA

units on 120 VAC or up

to 25 Freedom™ Strip Mini RGBA units on 230 VAC.

Note: Battery charging speed slows down during power linking.

The power linking diagram shown above corresponds to the North American

version of the product ONLY! If using the product

in other markets, you must

consult with the local CHAUVET® distributor as power linking connectors and

requirements may differ in your country or region.

1

st

Product

2

nd

Product

3

rd

Product

Additional

Products

Page 16 of 88 Freedom™ Par RGBA and Strip Mini RGBA User Manual Rev. 4

Mounting

Before mounting the product, read and follow the safety recommendations of the

Safety

Notes.

Orientation

The Freedom™ RGBA series products may be mounted in any position; however, make

sure adequate ventilation is provided.

Rigging

• Before deciding on a location, always make sure there is easy access to the product

for maintenance and programming.

• Make sure that the structure or surface onto which you are mounting the product

can support the product’s weight (see the Technical Specifications

).

• When mounting the product overhead, always use a safety cable.

Mount the

product securely to a rigging point, such as an elevated platform or a truss.

• When rigging the product onto a truss, you should use a mounting clamp of

appropriate weight capacity.

• When power linking multiple products, you must always consider the length of the

power linking cable and mount the products close enough for the cable to reach.

• The bracket adjustment knobs allow for directional adjustment when aiming the

product to the desired angle. Only loosen or tighten the bracket knobs manually.

Using tools could damage the knobs.

• The mounting brackets on the Freedom™ Strip Mini RGBA also serve as floor

supports/allow for surface mounting. When mounting the product

on the floor, make

sure that the product and cables are away from people and vehicles.

Mounting Diagram

Tilt Angle

Adjustment Knob

Mounting Bracket

Bracket Adjustment Knob

Mounting Brackets

Freedom™ Par RGBA and Strip Mini RGBA User Manual Rev. 4 Page 17 of 88

4. OPERATION

Control Panel

Operation

To access the control panel functions, use the four buttons surrounding the display.

Button Function

<MODE>

Selects an operation mode or backs out of the current menu option

<UP>

Scrolls up the list of options or selects a higher value

<DOWN>

Scrolls down the list of options or selects a lower value

<ENTER>

Activates a menu option or a selected value

Menu Map

Mode Programming Steps Description

SYS

SdAd

001

–

508

Set DMX address

d-CH

4CH

Turn on 4-channel DMX mode

5CH

Turn on 5-channel DMX mode

S-tr

tA.S t-AU

Automatically select transmit

frequency (for IR use)

t.CH

t001–

t016

Manually select transmit frequency

(for IR use)

drA.S dr.AU

Automatically select receive

frequency (for DMX use)

dr.CH

dr.01–

dr.16

Manually select receive frequency

(for DMX use)

dtA.S dt.AU

Automatically select transmit

frequency (for DMX use)

dt.CH

dt.01–

dt.16

Manually select transmit frequency

(for DMX use)

d-SL SL.00–SL.32

Set sound sensitivity (DMX mode)

SAAd

Reset software

ACt

(extra levels not

available in all

programs)

A001–A022

A024–A026

P.000–P.100

Run speed (slow to fast)

F.000–F.100

Flash speed (slow to fast)

SL.00–SL.32

Sound sensitivity (Automatic mode)

A023 Only

P.000–P.100

Red (only available in A023)

F.000–F.100

Green (only available in A023)

C.000–C.100

Blue (only available in A023)

Y.000–Y.100

Amber (only available in A023)

SL.00–SL.32

Sound sensitivity (Automatic mode)

ACtC

(extra levels not

available in all

programs)

AC01–AC12

AC14

P.000–P.100

Run speed (slow to fast)

F.000–F.100

Flash speed (slow to fast)

SL.00–SL.32

Sound sensitivity (Automatic mode)

AC13 Only

P.000–P.100

Red (only available in AC13)

F.000–F.100

Green (only available in AC13)

C.000–C.100

Blue (only available in AC13)

SL.00–SL.32

Sound sensitivity (Automatic mode)

SLAv

rA.S r-AU

Automatically select receive

frequency (for IR use)

r-St r001–r016

Manually select receive frequency

(for IR use)

S-Ir

Infrared connection with IRC

(Infrared Remote Control) only

Page 18 of 88 Freedom™ Par RGBA and Strip Mini RGBA User Manual Rev. 4

Configuration

(DMX)

Set the product in DMX mode to control with a DMX controller.

1. Connect the product to a suitable power outlet.

2. Turn the product on.

3. Connect a DMX cable from the DMX output of the DMX controller to the DMX input

socket on the product.

Starting Address

When selecting a starting DMX address, always consider the

number of DMX channels

the selected DMX mode uses. If you

choose a starting address that is too high, you could

restrict access to some of the product’s channels.

The Freedom™ RGBA series uses up to 5 DMX channels in its 5-CH

DMX mode, which

defines the highest configurable address to 508.

If unfamiliar with DMX, download the DMX Primer from www.chauvetlighting.com.

To select the starting address, do the following:

1. Press <MODE> repeatedly until SYS, ACt, ACtC, SLAv, or S-Ir shows on the

display.

2. Use <UP> or <DOWN> to select SYS.

3. Press <ENTER>.

4. Use <UP> or <DOWN> to select SdAd.

5. Press <ENTER>.

6. Use <UP> or <DOWN> to select the starting address.

7. Press <ENTER>.

DMX

Personalities

The Freedom™ RGBA series has 2 DMX personalities. One is a basic 4-channel

personality, and the other is a more advanced 5-channel personality.

To select either the 4- or 5-channel personality, do the following:

1. Press <MODE> repeatedly until SYS, ACt, ACtC, SLAv, or S-Ir shows on the

display.

2. Use <UP> or <DOWN> to select SYS.

3. Press <ENTER>.

4. Use <UP> or <DOWN> to select d-CH.

5. Press <ENTER>.

6. Use <UP> or <DOWN> to select either 4CH (4-channel mode) or

5CH (5-channel mode).

7. Press <ENTER>.

Freedom™ Par RGBA and Strip Mini RGBA User Manual Rev. 4 Page 19 of 88

DMX Channel Modes, Assignments, and Values

5-CH

Channel Function Value CH.2 CH.3 CH.4 CH.5

1

Blackout

000 ó 008

Flash speed

000 ó 249

Sound-Active

250 ó 255

Red

009 ó 017

Green

018

ó

026

Blue

027 ó 035

Amber

036 ó 044

Red + Green

045 ó 053

Red + Blue

054 ó 062

Red + Amber

063 ó 071

Green + Blue

072 ó 080

Blue + Amber

081 ó 089

Red + Green +

Blue

090 ó 098

Green + Amber

099 ó 107

Red + Green +

Amber

108 ó 116

Red + Blue +

Amber

117 ó 125

Green + Blue +

Amber

126 ó 134

Red + Green +

Blue + Amber

135 ó 143

Color Change 1

144 ó 152

Run speed

Automatic

000 ó 127

Sound-Active

128 ó 255

Color Change 2

153 ó 161

Color Chase 1

162 ó 170

Color Chase 2

171 ó 179

Color Chase 3

180 ó 188

Color Chase 4

189 ó 197

Color Change 3

198

ó

206

RGBA Mode 207 ó 215

Red

(0–100%)

000

ó

255

Green

(0–100%)

000

ó

255

Blue

(0–100%)

000

ó

255

Amber

(0–100%)

000

ó

255

Color Snap 216 ó 224

Snap speed

000 ó 255

Color Fade 225 ó 233

Fade speed

000 ó 255

Auto Run

(Sound-Active

only)

234 ó 255

Run speed

Automatic

000 ó 127

Sound-Active

128 ó 255

Note: The sound sensitivity settings in ACt and ACtC modes have an effect on the sound sensitivity span in

DMX mode. For optimal sound sensitivity in DMX mode, first be sure to adjust both ACt and ACtC sound

sensitivity settings according to your environment.

• CH.2 must be within operating values for Auto Run to function.

• If the Freedom™ RGBA series product is in Sound-Active mode and there is no

sound for 6 seconds, the product will default back to an automatic program. Turn

the sound sensitivity down to 128 to avoid this.

4-CH

Channel Function Value Percent

1

Red

000 ó 255

0–100%

2

Green

000 ó 255

0–100%

3

Blue

000 ó 255

0–100%

4

Amber

000 ó 255

0–100%

Page 20 of 88 Freedom™ Par RGBA and Strip Mini RGBA User Manual Rev. 4

Configuration

(Standalone)

Set the product in one of the standalone modes to control without a DMX controller.

1. Connect the product to a suitable power outlet.

2. Turn the product on.

Never connect a product that is operating in any standalone mode

(Static, Automatic, or Sound)

to a DMX string connected to a DMX controller.

Product

s in standalone mode may transmit DMX signals that could interfere with

the DMX signals from the controller.

Automatic ACt

Mode

To enable the Automatic ACt mode, do the following:

1. Press <MODE> repeatedly until SYS, ACt, ACtC, SLAv, or S-Ir shows on the

display.

2. Use <UP> or <DOWN> to select ACt.

3. Press <ENTER>.

4. Use <UP> or <DOWN> to choose your desired program (A001–A026).

5. Press <ENTER>.

Certain programs will have additional functionality. To find these options, press

<ENTER> after selecting an auto program. Then press <UP> or <DOWN> to choose the

desired setting. Not every program will feature additional functions.

Function Description

F.000–F.100 Flash speed (slow to fast)

SL.00–SL.32 Sound sensitivity (Automatic mode)

P.000–P.100 Run speed (slow to fast)

C.000–C.100 Blue

Y.000–Y.100 Amber

Freedom™ Par RGBA and Strip Mini RGBA User Manual Rev. 4 Page 21 of 88

ACt Auto

Programs

Program Function

A000 No function

A001 Red

A002

Green

A003 Blue

A004 Amber

A005

Red + Green

A006 Red + Blue

A007 Red + Amber

A008 Green + Blue

A009 Blue + Amber

A010 Red + Green + Blue

A011 Green + Amber

A012

Red + Green + Amber

A013 Red + Blue + Amber

A014 Green + Blue + Amber

A015

Red + Green + Blue + Amber

A016 Color change 1

A017 Color change 2

A018

Color chase 1

A019

Color chase 2

A020 Color chase 3

A021

Color chase 4

A022 Color change 3

A023 RGB full on

In this channel:

P is Red (P.000–P.100)

F is Green (F.000–F.100)

C is Blue (C.000–C.100)

Y is Amber (Y.000–Y.100)

A024 Color snap

A025

Color fade

A026 Sound-Active

Page 22 of 88 Freedom™ Par RGBA and Strip Mini RGBA User Manual Rev. 4

Automatic ACtC

Mode

The Automatic ACtC (Compatibility) mode allows the Freedom™ RGBA

series products

to operate in conjunction with previous models in the Freedom™ series.

To enable the Automatic ACtC mode, do the following:

1. Press <MODE> repeatedly until SYS, ACt, ACtC, SLAv, or S-Ir shows on the

display.

2. Use <UP> or <DOWN> to select ACtC.

3. Press <ENTER>.

4. Use <UP> or <DOWN> to choose your desired program (AC00–AC23).

5. Press <ENTER>.

Certain programs will have additional functionality. To find these options, press

<ENTER> after selecting an auto program. Then press <UP> or <DOWN> to select the

desired setting. Not every program will feature all the added functionality.

Function Description

F.000–F.100 Flash speed (slow to fast)

SL.00–SL.32 Sound sensitivity (Automatic mode)

P.000–P.100 Run speed (slow to fast)

C.000–C.100 Blue

ACtC Auto

Programs

Program Function

AC00 No function

AC01 Red

AC02 Green

AC03

Blue

AC04 Yellow

AC05 Purple

AC06

Cyan

AC07

White

AC08 Color change 1

AC09

Color change 2

AC10 Color change 3

AC11 Color change 4

AC12

Color change 5

AC13 RGB full on

In this channel:

P is Red (P.000–P.100)

F is Green (F.000–F.100)

C is Blue (C.000–C.100)

AC14 Color fade

Freedom™ Par RGBA and Strip Mini RGBA User Manual Rev. 4 Page 23 of 88

IRC (Infrared

Remote Control)

The Freedom™ RGBA series is fully compatible with the Infrared Remote Control (IRC)

from CHAUVET® (sold separately).

To set up a Freedom™ RGBA series product to operate with the IRC, do the following:

1. Press <MODE> repeatedly until SYS, ACt, ACtC, SLAv, or S-Ir shows on the

display.

2. Use <UP> or <DOWN> to select S-Ir.

3. Press <ENTER>.

4. Begin using the IRC.

IRC Operation

Automatic Mode

Automatic mode will enable you to run the automatic programs on the product.

To turn on Automatic mode:

1. Press <AUTO> on the IRC.

2. Press <+> or <–> to choose between the different auto programs.

To adjust the speed of the automatic program:

1. Press <SPEED> on the IRC.

2. Press <+> or <–> to either increase or decrease the speed of the program.

Sound-Active Mode

Sound-Active mode will enable the product to respond to the music.

To turn on Sound-Active mode:

1. Press <SOUND> on the IRC.

2. Press <+> or <-> to either increase or decrease reacting sensitivity.

To adjust sound sensitivity in Sound-Active mode:

1. Press <SENSITIVITY> on the IRC.

2. Press <+> or <–> to either increase or decrease sound sensitivity.

Page is loading ...

Chauvet Freedom Strip Mini RGBA User manual

Chauvet Freedom Strip Mini RGBA User manual

in other languages

Related papers

Other documents