Front Runner KSFF002T Installation guide

ENG

FORD F150 SUPER CREW (2009-CURRENT)

SLIMSPORT ROOF RACK KIT

KSFF001_REV_A05

1

Don’t be a hero and muscle through this installation without reading these ﬁtting instructions ﬁrst! Improper installation of this gear may void certain

aspects of your warranty.

Before you begin, take a moment and open all your Front Runner rack kit boxes and gather the assembly instructions for the various components.

A complete kit will contain:

1. A Front Runner Slimsport kit

This document will guide you through the assembly of the mounting system and assist you in ﬁtting the roof rack tray or load bars to your speciﬁc

vehicle.

Please refer to the next page for a list of all the components, quantities and tools required.

KSFF001

READ ME FIRST

START HERE!

front runner

IMPORTANT WARNING!

IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD

RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT

RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND

DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO

INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY

FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.

NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.

Please call us if you have any questions about the installation of this product.

2

KSFF001_REV_A05

FIGURE 1.1

IN THE BOX

1 2 X Foot Rail 1LH + 1RH

2 6 X Stiffener plates

3 8 X Standard Slimsport Slat

4 12 X 6mm Spacer

5 12 X M6x16 Button Head Flange

6 12 X M6x19x1 Flat Washer

7 12 X M6 Spring Washer

8 12 X M6x50 Hex Bolt

9 24 X M6 Nut Cap

10 12 X Jack Nut

11 12 X M6 Nyloc Nut

12 32 X M6x25 Thread Forming Screw

13 1 X Installer Wrench

14 2 X M6x30 Button Head

1GET ORGANIZED

TOOLS NEEDED

4

10

4

5

11

9

2

6

7

8

9

12 13

14

Torx

T30

10mm

13mm

5mm

Anti

Rust

Masking

Tape

Cordless

Driver Silicone

CHECK ONLINE FOR LATEST FITMENT GUIDE WWW.FRONTRUNNEROUTFITTERS.COM

Oil

1

3

Secure the support plates (Item 3) to the

Foot Rails (Item 1) using M6x16 Button Head

Flange Bolt , M6 Nyloc Nut & M6 Nut Cap

(Items 12, 16 & 18).

Secure the Side Wind Fairing Supports

(Item 2) to the Foot Rails (Item 1) using

M6x16 Button Head Flange Bolt , M6 Nyloc

Nut & M6 Nut Cap (Items 12, 16 & 18)

3

KSFF001_REV_A05

FIT AND SECURE

2

2.1

2.2

Assemble the Stiffener Pates (Item 2) to

the foot rails (Item 1) using M6x16 ﬂange

button heads, M6 nyloc nut & M6 nut cap

(Items 5, 9 & 11).

Do this to both LH & RH foot rails.

Fully tighten.

Fit seven Slimsport Slats (Item 3) to foot rails

assemblies using M6x25 thread forming

screws (Item 12).

.

12

3

1

2

11

9

5

1

Note do not ﬁt the Front Slat.

Use a little oil on screw threads before

inserting. Note these are Thread

Forming Screws.

10mm

Torx

T30

Torx

T30

Cordless

Driver

Cordless

Driver

Tightening Torque 8-10Nm /

5.9 ft lb - 7.38 ft lb. Take care when

using a cordless driver.

4

KSFF001_REV_A05

FIT AND SECURE

3

3.1

3.2

Refer to ﬁtment guide RRAC233

Refer to ﬁtment guide RRAC194

10mm

STANDARD WIND FAIRING ASSEMBLY

LIGHT BAR WIND FAIRING ASSEMBLY

10

14

13

5

KSFF001_REV_A05

FIT AND SECURE

4

4.1

4.2

4.3

Apply masking tape along the length of the

ditch. Locate the rivet on the ditch molding at

the rear of the cab.

Measure 200mm toward the front of the

vehicle from the center of the rivet. And make

a mark in the center of the ditch. This will be

the rear hole for the Foot Rail.

Do not fully Thighten.

Torx

T30

13mm

Torx

T30

Cordless

Driver

200mm

Position the assembled Rack onto the

vehicle. Align the rear mount hole in the Foot

Rail with the rear mark you made earlier in

4.1 and mark the remaining ﬁve hole centers.

Check Antenna clearance before drilling.

Please contact help center if you are unsure.

Remove the Rack from the vehicle.

Drill a 5mm Pilot hole in the center of the

markings. Open the holes using a 12mm drill

bit.

Clean any excess debris around the

holes. Do not apply exesive force let

the drill do the work. There is an airbag

curtain below. Use a blade to remove

+/-2mm of the mastic around the hole

to ensure jack nut will seat ﬁrmly on

metal. Apply anti rust.

Make sure that the Jack Nut has pulled

up all the way to the inside skin of the

roof panel.

Insert an M6 button head bolt (Item 14) into

the side of the installer wrench (Item 13).

Loosely ﬁt a jack nut (Item 10) to the button

head bolt as shown.

Using the installer wrench and a M6x30

button head bolt, insert the M6 jack nuts into

all 12 holes.

Using a cordless driver and a 4mm allen

cordless bit, set the jack nut into the hole

while holding onto the handle of the installer

wrench.

6

KSFF001_REV_A05

FIT AND SECURE

4

4.4

COMPLETION

5

5.1

Congratulations! You did it. Take a step back and admire your work!

INSTALL OTHER VEHICLE AND RACK ACCESSORIES

6

Now's the time to visit your favorite Front Runner Dealer in person or online.

IMPORTANT!

Be sure to tag us. We love to see our gear in action! #FrontRunnerOutﬁtters #BornToRoam

Share your adventures on:

FRONT RUNNER RACK KITS OFTEN HAVE A HIGHER LOAD RATING THAN THE VEHICLES THEY ARE MOUNTED TO. PLEASE REFER TO YOUR SPECIFIC VEHICLE MANUFACTURER

FOR A RECOMMENDED ROOF RATING. FRONT RUNNER CANNOT BE RESPONSIBLE FOR IMPROPER LOADING BEYOND THE VEHICLE MANUFACTURER'S STATED LOAD CAPACITY.

9

8

7

6

4

10

Place silicone over each of the jack nut

openings.

Stack 2 Spacers (Item 4) over the jack nuts

inserted in 2.8.

Position the rack over the cab placing it on

spacers inserted earlier.

Place a bead of silicone along the threads

of the M6x50 Hex Bolts and secure the rack

using M6x50 Hex Bolts, M6 Spring Washers &

M6x19x1 Flat Washers (Items 6, 7 & 8). Fully

tighten.

Place M6 Nut Caps (Item 9) over all Hex

Bolts.

Front Runner KSFF002T Installation guide

This manual is also suitable for

Front Runner KSFF002T Installation guide

Related papers

Other documents