Heat & Glo LCOR/RCOR/PIER/ST-HVB-CE Install Manual

Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev. o • 3/13 1

Models:

PIER-HVB-CE

ST-HVB-CE

LCOR-HVB-CE

RCOR-HVB-CE

Installers Guide

READ THIS MANUAL BEFORE INSTALLING OR OPERAT-

ING THIS APPLIANCE. THIS INSTALLERS GUIDE MUST

BE LEFT WITH APPLIANCE FOR FUTURE REFERENCE.

Please contact your Heat & Glo dealer with any questions or

concerns. For the number of your nearest Heat & Glo dealer,

please visit www.heatnglo.com.

Heat & Glo, a brand of Hearth & Home Technologies

7571 215th Street West, Lakeville, MN 55044, USA

0086

This is a room sealed appliance and no other ventilation is

required than what is provided.

These instructions are only valid if the following country symbol is

on the appliance. If this symbol is not present on the appliance,

it is necessary to refer to the technical instructions which will

provide the necessary information concerning the modication

of the appliance to the conditions of use for the country.

These instructions are valid for the following countries: GB, IE

WARNING

This appliance has been supplied with an integral barrier





HOT SURFACES!

Glass and other surfaces are hot during

operation AND cool down.

Hot glass will cause burns.

• DO NOT touch glass until it is cooled

• NEVER allow children to touch glass

• Keep children away

• CAREFULLY SUPERVISE children in same room as

replace.

• Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other ammable

materials.

• Keep clothing, furniture, draperies and other ammable

materials away.

• Do not store or use gasoline or other am-

mable vapors and liquids in the vicinity of

this or any other appliance.

• What to do if you smell gas

- Do not try to light any appliance

- Do not touch any electrical switch. Do not

use any phone in your building.

- Immediately call your gas supplier from a

neighbor’s phone. Follow the gas suppli-

er’s instructions.

- If you cannot reach your gas supplier, call

the re department.

• Installation and service must be performed

by a qualied installer, service agency, or the

gas supplier.

WARNING: If the information in these

instructions is not followed exactly, a re

or explosion may result causing property

damage, personal injury, or death.

This product is covered by one or more of the following patents: (United States) 5601073, 5613487, 5647340, 5890485, 5941237, 6006743, 6019099, 6053165,

6145502, 6374822, 6484712, 6601579, 6769426, 6863064, 7077122, 7098269, 7258116, 7470729, 8147240 or other U.S. and foreign patents pending.

2000-945B



Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev. o • 3/13

2

!

!!

!

Safety and Warning Information

!

This appliance is intended for use on a gas installation

with a governed meter.

DO NOT place furniture or any other combustible

household objects within 36 inches of the replace

front.

Any safety screen or guard removed for servicing must

be replaced before operating this appliance.

Turn off the gas before servicing this appliance. It

is recommended that a qualied service technician

perform an appliance check-up at the beginning of

each heating season.

   abrasive cleaners on the glass door

assembly. to clean the glass door

when it is hot.

The glass door assembly be replaced

as a complete unit, as supplied by the gas replace

manufacturer.   material may be

used.

   this appliance with the glass

door removed, cracked, or broken. Replacement of

the glass door should be performed by a licensed or

qualied service person. strike or slam the

glass door.

The glass door assembly  be in place and

sealed, and the trim door assembly be in place

on the replace before the unit can be placed into safe

operation.

 the external ue cap on a regular basis to

make sure that no debris is interfering with the air ow.

This gas replace and ue assembly ue directly

to the outside and   be attached to a

chimney serving a separate solid fuel burning appliance.

Each gas appliance a separate ue system.

Common ue systems are .

These units  use one of the flue systems

described in the Installing the Fireplace section of

the Installers Guide.   flue systems or

components .

Children and adults should be ALERTED to the hazards

of high surface temperature and should STAY AWAY to

avoid burns or clothing ignition. Young children should

be CAREFULLY SUPERVISED when they are in the

same room as the appliance.

Due to the high temperature, the appliance should be

out of trafc areas and away from furniture

and draperies. Clothing or ammable material 

on or near the appliance.

  the flow of combustion and

ventilation air. Keep the front of the appliance 

of all obstacles and materials for servicing and proper

operations.

Always  the appliance clear and free from

combustible materials, petrol, and other ammable

vapors and liquids.

Installation and repair should be by a

qualied service person. The appliance and ueing

system should be before initial use and at

least annually by a professional service person. More

frequent cleaning may be required due to excessive lint

from carpeting, bedding material, etc. It is 

that the unit’s control compartment, burners, and

circulating air passageways    to

provide for adequate combustion and ventilation air.



   this appliance if any part has been

under water. Immediately  a qualied service

technician to inspect the unit and to replace any part

of the control system and any gas control which has

been under water.

Prior to the rst ring of the replace, READ the Using

Your Fireplace section of the Owners Guide.

READ and UNDERSTAND all instructions carefully

before starting the installation. 

these installation instructions may result in a possible

re hazard and will void the warranty.

Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev. o • 3/13 3

Table of Contents

Safety and Warning Information ..................................................2

Service Parts List ..........................................................................4

Appliance Certication ................................................................................. 10

Introducing the Heat & Glo Gas Fireplaces ................................................. 10

Pre-install Preparation ................................................................................. 10

Approvals and Regulations ........................................................10

Getting Started .............................................................................10

Installation Regulations ..............................................................10

Step 1. Locating the Fireplace .................................................................... 14

Installing the Fireplace................................................................14

Step 2. Framing the Fireplace ..................................................................... 14

Step 3. Installing the Flue System .............................................................. 17

A. Flue System Approvals .......................................................... 17

B. Installing Flue Components ................................................... 24

C. Flue Termination .................................................................... 26

Step 4. Positioning, Leveling, and Securing the Fireplace .......................... 29

Step 5. The Gas Control System ................................................................ 29

Step 6. The Gas Supply Line ...................................................................... 30

Step 7. Gas Pressure Requirements .......................................................... 30

Step 8. Wiring the Fireplace ........................................................................ 31

Optional Accessories ................................................................................... 31

Wall Switch .................................................................................................. 31

Step 9. Finishing ......................................................................................... 31

Step 10. Installing Trim, Logs & Ember Material .......................................... 32

Installing the Trim ........................................................................ 32

Attachment of Lower Door Assembly .......................................... 32

Placing the Ember Material ......................................................... 37

Step 11. Before Lighting the Fireplace ....................................................... 38

Step 12. Lighting the Fireplace ................................................................... 38

After the Installation ..................................................................................... 38

Maintaining and Servicing Your Fireplace ................................39

 = Contains updated information



Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev. o • 3/13

4

Service Parts

Beginning Manufacturing Date: June 2004

Ending Manufacturing Date: Active

Log Set Assembly

36” Left Corner Gas Fireplace - DV

IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement parts for your appliance please

provide model number and serial number. All parts listed in this manual may be ordered from an authorized dealer.

ITEM DESCRIPTION COMMENTS PART NUMBER

Log Set Assembly LOGS-ST-CE

1 Glass Assembly (End) GLA-MS

2 End Panel Assembly 2069-042

3 Grate Assembly 2068-020

4 Glass Assembly (Side) GLA-6TROC

5 Dress Guard Assembly 2068-040

6 Lower Door 2068-041

7Burner N 2068-011

Burner P & B 2068-013

Hood, Side, Black SRV2005-190

Hood, End, Black SRV2006-194

Mesh Assembly (End) 561-330A

Mesh Assembly (Side) 537-300

Non-combustible Board (Side) 2006-136

Non-combustible Board (Back) 2006-137

Refractory (Side) SRV2005-730

Refractory (End) SRV2005-731

Additional service part numbers appear on following page. 3/13

1

2

3

4

5

67

LCOR-HVB-CE

Service Parts List

Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev. o • 3/13 5

Service Parts

Beginning Manufacturing Date: June 2004

Ending Manufacturing Date: Active

Log Set Assembly

3-Sided Gas Fireplace - DV

IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement parts for your appliance please

provide model number and serial number. All parts listed in this manual may be ordered from an authorized dealer.

ITEM DESCRIPTION COMMENTS PART NUMBER

Log Set Assembly LOGS-ST-CE

1 Grate Assembly 2068-020

2 Glass Assembly (Side) GLA-6TROC

3 Dress Guard Assembly 2068-040

4 Lower Door 2068-041

5Burner N 2068-011

Burner P & B 2068-013

6 Glass Assembly (End) GLA-MS

7 End Panel Assembly 2069-042

Hood, Side, Black SRV2005-190

Hood, End, Black SRV2006-194

Mesh Assembly (End) 561-330A

Mesh Assembly (Side) 537-300

Non-combustible Board (Side) 2006-136

Non-combustible Board (Back) 2006-137

Refractory (Side) SRV2005-730

Additional service part numbers appear on following page. 3/13

1

2

3

456

7

PIER-HVB-CE

Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev. o • 3/13

6

Service Parts

Beginning Manufacturing Date: June 2004

Ending Manufacturing Date: Active

Log Set Assembly

36” Right Corner Gas Fireplace - DV

IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement parts for your appliance please

provide model number and serial number. All parts listed in this manual may be ordered from an authorized dealer.

ITEM DESCRIPTION COMMENTS PART NUMBER

Log Set Assembly LOGS-ST-CE

1 Grate Assembly 2068-020

2 Glass Assembly (Side) GLA-6TROC

3 Dress Guard Assembly 2068-040

4 Lower Door 2068-041

5Burner N 2068-011

Burner P & B 2068-013

6 Glass Assembly (End) GLA-MS

7 End Panel Assembly 2069-042

Hood, Side, Black SRV2005-190

Hood, End, Black SRV2006-194

Mesh Assembly (End) 561-330A

Mesh Assembly (Side) 537-300

Non-combustible Board (Side) 2006-136

Non-combustible Board (Back) 2006-137

Refractory (End) SRV2005-731

Refractory (Side) SRV2005-730

Additional service part numbers appear on following page. 3/13

1

2

3

456

7

RCOR-HVB-CE

Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev. o • 3/13 7

Service Parts

Beginning Manufacturing Date: June 2004

Ending Manufacturing Date: Active

Log Set Assembly

1

2

3

4

56

See-Thru Gas Fireplace - DV

IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement parts for your appliance please

provide model number and serial number. All parts listed in this manual may be ordered from an authorized dealer.

ITEM DESCRIPTION COMMENTS PART NUMBER

Log Set Assembly LOGS-ST-CE

1 Refractory SRV2005-730

2 Grate Assembly 2068-020

3 Glass Assembly (Side) GLA-6TROC

4 Dress Guard Assembly 2068-040

5 Lower Door 2068-041

6Burner N 2068-011

Burner P & B 2068-013

Hood, End, Black SRV2006-194

Mesh Assembly 537-300

Non-combustible Board 2006-136

Additional service part numbers appear on following page. 3/13

ST-HVB-CE

Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev. o • 3/13

8

Service Parts

Beginning Manufacturing Date: June 2004

Ending Manufacturing Date: Active

#8 Valve Assembly 8.1

8.2

8.3

8.4

8.5

8.6

8.7

8.8

8.9

8.10

8.11

IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement parts for your appliance please

provide model number and serial number. All parts listed in this manual may be ordered from an authorized dealer.

ITEM DESCRIPTION COMMENTS PART NUMBER

8.1 Pilot Assembly N 529-550A

Pilot Assembly P 529-551A

8.2 Pilot Bracket 2068-114

8.3 Flexible Gas Connector 530-302A

8.4 Burner Leg, Pilot Support 2068-112

8.5 Universal Bracket 2068-111

8.6 Valve Bracket 2068-115

8.7 Piezo Ignitor 291-513

8.8 Flex Ball Valve Assembly 302-330A

8.9 Valve N 060-524

Valve P 060-526

8.10 On/ Off Wire Assembly 060-521A

8.11 Burner Leg 2068-113

20" Wire Harness 107-559A

Ori ce N (#33DMS) 582-833

Ori ce P (#51DMS) 582-851

Ori ce B (#53DMS) 582-853

Additional service part numbers appear on following page.

LCOR, PIER, RCOR, & ST-HVB-CE

Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev. o • 3/13 9

Service Parts

Beginning Manufacturing Date: June 2004

Ending Manufacturing Date: Active

IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement parts for your appliance please

provide model number and serial number. All parts listed in this manual may be ordered from an authorized dealer.

ITEM DESCRIPTION COMMENTS PART NUMBER

Bracket Junction Box 2068-106

Door Stop 2068-144

Fan Kit GFK-240V

Fiber Glass Rope 060-455

Glass Latch Assembly Pkg of 2 33858/2

Junction Box 546-250A

Lava Rock 2005-790

Mineral Wool 050-721

Touch Up Paint TUP-GBK-12

Wall Thermostat Kit MV-STAT

Wall Switch kit, Off White WSK-21

Wall Switch Kit, White WSK-21-W

Conversion Kit N NGK-ST-CE

Conversion Kit P LPK-ST-CE

Conversion Kit B BGK-ST-CE

Pilot Ori ce N 529-512

Pilot Ori ce P 200-2630

Regulator N 230-1570

Regulator P & B 230-1520

LCOR, PIER, RCOR, & ST-HVB-CE

Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev. o • 3/13 10

Appliance Certication

The Heat & Glo replace models discussed in this Installers

Guide have been tested to certication standards and listed

by the applicable laboratories.

1Approvals and Regulations

2Getting Started

Introducing the Heat & Glo Gas Fireplaces

Heat & Glo direct ue gas replaces are designed to oper-

ate with all combustion air siphoned from outside of the

building and all exhaust gases expelled to the outside.

The information contained in this Installers Guide, unless

noted otherwise, applies to all models and gas control

systems. Gas replace diagrams, including the dimensions,

are shown in this section.

Pre-install Preparation

This gas replace and its components are tested and safe

when installed in accordance with this Installers Guide.

Report to your dealer any parts damaged in shipment,

particularly the condition of the glass. Do not install any

unit with damaged, incomplete, or substitute parts.

The ue system components are shipped in separate pack-

ages. The gas logs are packaged separately and must be

eld installed.

Read all of the instructions before starting the instal-

lation. Follow these instructions carefully during the

installation to ensure maximum safety and benet. Fail-

ure to follow these instructions will void the owner’s

warranty and may present a re hazard.

The Heat & Glo Warranty will be voided by, and Heat & Glo

disclaims any responsibility for, the following actions:

• Installation of any damaged replace or ue system

component.

• Modication of the replace or direct ue system.

• Installation other than as instructed by Heat & Glo.

• Improper positioning of the gas logs or the glass door.

• Installation and/or use of any component part not manu-

factured and approved by Heat & Glo, not withstanding

any independent testing laboratory or other party ap-

proval of such component part or accessory.

ANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE

HAZARD.

When planning a replace installation, it’s necessary

to determine:

• Where the unit is to be installed.

• The ue system conguration to be used.

• Gas supply piping.

• Electrical wiring.

• Framing and nishing details.

• Whether optional accessories—devices such as a fan,

wall switch, or remote control—are desired.

If the replace is to be installed on carpeting, tile or

any combustible material other than wood ooring,

it should be installed on a metal or wood panel that

extends the full width and depth of the replace.

Installation Regulations

Before installation check that local distribution conditions,

nature of gas and pressure, and adjustment of the

appliance are compatible.

This appliance must be installed with the rules in force,

and used only in a sufciently ventilated space. Consult

instructions before installation and use of this appliance.

Certication

MODELS: PIER-HVB-CE, ST-HVB-CE,

LCOR-HVB-CE, RCOR-HVB-CE

LABORATORY: BSI

TYPE: Gas Fireplace

STANDARD: BS EN 613:2001 (Amd 1)

DIRECTIVE: GAD2009/142/EC

Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev. o • 3/13

11

Figure 1. Diagram of the PIER-HVB-CE

TOP FLUE

COLLARS

REAR FLUE

COLLARS

ELECTRICAL

ACCESS

GAS LINE

ACCESS

GAS CONTROLS

AND LABELS

TOP STANDOFFS

133 mm

306 mm

13 mm

1082 mm

1067 mm

456 mm

816 mm

58 mm

121 mm

102 mm

114 mm

ELECTRICAL

ACCESS

GAS LINE

ACCESS

305 mm

451 mm

245 mm

610 mm

245 mm

882 mm

Ø 204 mm

950 mm

451 mm

Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev. o • 3/13 12

Figure 2. Diagram of the ST-HVB-CE

133 mm

306 mm

13 mm

1183 mm

1067 mm 820 mm

533 mm

919 mm

58 mm

121 mm

102 mm

114 mm

ELECTRICAL

ACCESS GAS LINE

ACCESS

305 mm

114 mm

64 mm

610 mm

216 mm

882 mm

Ø 204 mm

TOP FLUE

COLLARS

REAR FLUE

COLLARS

ELECTRICAL

ACCESS

GAS LINE

ACCESS

GAS CONTROLS

AND LABELS

TOP STANDOFFS

Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev. o • 3/13

13

Figure 3. Diagram of the LCOR-HVB-CE and RCOR-HVB-CE

133 mm

306 mm

13 mm

1082 mm

1067 mm

456 mm

816 mm

743 mm

245 mm

612 mm

245 mm

Ø 204 mm

950 mm

451 mm

456 mm

58 mm

184 mm

254 mm

121 mm

305 mm

882 mm

Ø 204 mm

64 mm

TOP FLUE

COLLARS REAR FLUE

COLLARS

ELECTRICAL

ACCESS

ELECTRICAL

ACCESS

GAS LINE

ACCESS

GAS LINE

ACCESS

GAS CONTROLS

AND LABELS

TOP STANDOFFS

Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev. o • 3/13 14

3Installing the Fireplace

Step 1. Locating the Fireplace

The diagram below shows space and clearance require-

ments for locating a replace within a room.

Minimum Clearances

from the Fireplace to Combustible Materials

Figure 4. Fireplace Dimensions and Locations

For minimum clearances, see the direct ue termination

clearance diagrams on pages 30 and 31 in this manual.

Step 2. Framing the Fireplace

Fireplace framing can be built before or after the replace is

set in place. Framing should be positioned to accommodate

wall coverings and replace facing material. The diagram

below shows framing reference dimensions.







Minimum Clearances

from the Flue Pipe to Combustible Materials

* The clearance to the ceiling is measured from the top of

the unit, excluding the standoffs (see Figures 37 & 38).

The distance from the unit to combustible construction is

to be measured from the unit outer wrap surface to the

combustible construction, NOT from the screw heads that

secure the unit together.

!

WARNING: FRAMING DIMENSIONS ASSUME

USE OF 1/2 INCH THICK WALL COVERING

MATERIALS ON EXTERIOR OF FRAMING

ONLY AND NO SHEETROCK ON INTERIOR

OF FRAMING.

mm inches

Glass Sides or Ends ..........914 ..................... 36

Floor ....................................0 ........................ 0

Rear Flue ............................13 ......................1/2

Metal Sides or Ends ...........13 ......................1/2

Top ......................................64 .................... 2 1/2

Ceiling* ..............................787 ..................... 31

mm Inches

. ............. 25 .................1

Horizontal Sections

Top .....................................75 .................3

Bottom ...............................25 ................. 1

Sides..................................25 .................1



Top ................................... 63.7 .............2 1/2

Bottom ...............................13 ............... 1/2

Sides..................................25 .................1

Clearance Requirements

The top, back, and sides of the replace are dened by

stand-offs. The minimum clearance to a perpendicular wall

extending past the face of the replace is 25 mm (1 in.).

The metal ends of the replace may NOT be recessed into

combustible construction.

914 mm

GLASS

914 mm

GLASS

914 mm

GLASS

914 mm

GLASS

914 mm

ST-HVB-CE

TOP VIEW

LCOR-HVB-CE

TOP VIEW

RCOR-HVB-CE

TOP VIEW

PIER-HVB-CE

TOP VIEW

Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev. o • 3/13

15

PIER-HVB-CE

ST-HVB-CE L & R-COR-HVB-CE

D

A

C

B

E

B

CC

AA

Framing should be constructed

of 51 mm x 102 mm (2 in. x 4 in.)

lumber or heavier.

Model A B C D E

PIER-HVB-CE 107 (42-1/8) 108 (42-1/2) 58 (23) 91 (35-3/4) 122 (48)

ST-HVB-CE 121 (47-5/8) 108 (42-1/2) 58 (23) 91 (35-3/4) 122 (48)

L&RCOR-HVB-CE 107 (42-1/8) 108 (42-1/2) 73 (28-3/4) 91 (35-3/4) 122 (48)

Figure 5. Framing Dimensions

NOTE: DIMENSIONS SHOWN IN CENTIMETERS AND (INCHES).

Shows center of 254mm x 305mm (10”x12”) ue framing holes for top and rear ueing.

The center of the hole is 25.4mm (one inch) above the center of the horizontal ue pipe.

Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev. o • 3/13 16

NOTE: PIPES OVERLAP 32 mm (1-1/4 in.) AT EACH JOINT.

Figure 6. DVP-Series Direct Flue Component Specications (127 mm (5 in.) inner pipe / 203 mm (8 in.) outer pipe)

DVP90ST

320 mm

286 mm

185 mm

32 mm

18 mm

218 mm

DVP36

DVP48

1219 mm

610 mm

914 mm

102 mm

152 mm

DVP4

DVP6

305 mm

DVP12

51 mm MIN.

DVP12A

310 mm MAX.

DVP24

251 mm

45

261 mm

DVP45

362 mm

º

Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev. o • 3/13

17

Figure 7. Flue System Components and Termination Kits

Step 3. Installing the Flue System

A. Flue System Approvals

These models are approved to use DVP series direct ue

pipe components and terminations (see Figures 6 and 7).

Approved ue system components are labeled for identi-

cation. This pipe is tested and listed as an approved com-

ponent of the replace. The pipe is tested to be run inside

an enclosed wall. There is no requirement for inspection

openings at each joint within the wall. There is no required

pitch for horizontal ue runs. NO OTHER FLUEING SYS-

TEMS OR COMPONENTS MAY BE USED.

Detailed installation instructions are included with each

ue termination kit and should be used in conjunction with

this Installers Guide.

The ame and ember appearance may vary based on the

type of fuel burned and the ueing conguration used.

Identifying Flue Components

The ue systems installed on this gas replace may include

one, two, or three 90° elbow assemblies. The relationships

of vertical rise to horizontal run in ue congurations using

90° elbows MUST BE strictly adhered to. The rise to run

relationships are shown in the ueing drawings and tables.

Refer to the diagrams on the next several pages.

NOTE: Two 45° elbows may be used in place of one

90° elbow. Rise to run ratios in the ue system must

be followed if 45° elbows are used.

This model has a 450 elbow built into it. It may be posi-

tioned to ue either horizontal or vertical. Depending on

the installation, decide which direction the elbow should be

facing. Remove the 8 screws from the corner cover plate.

Position the 450 elbow as desired and replace the corner

cover plate with the 8 screws.

HORIZONTAL TERMINATION

WALL FIRESTOPS

90º ELBOW

VERTICAL

TERMINATION

STORM COLLAR

ROOF FLASHING

PIPE LENGTH

CEILING FIRESTOP

TERMINATION KITS

DVP-TRAP DVP-TVHW

Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev. o • 3/13 18

Figure 8

STRAIGHT OUT

HORIZONTAL FLUEING

H

Max. Run

610 mm (24 in.)

Figure 9.

V

TERMINATION CAP

H

STRAIGHT UP

VERTICAL FLUEING

V (FT.)

12.2M MAX. (40 FT.)

Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev. o • 3/13

19

Figure 11. Flueing with One 90° Elbow

Figure 10. Flueing with One 90° Elbow

V

H

V

NATURAL GAS - FLUEING WITH ONE 90° ELBOW

V (FT.) H (FT.)

1’ MIN. (305 mm) 3’ MAX. (914 mm)

2’ MIN. (610 mm) 6’ MAX. (1.83 m)

3’ MIN. (914 mm) 9’ MAX. (2.7 m)

4’ MIN. (1.22 m) 12’ MAX. (3.6 m)

5’ MIN. (1.5 m) 15’ MAX. (4.5 m)

6’ MIN. (1.83 m) 18’ MAX. (5.5 m)

V + H = 40’ MAX. (12.2 m)

PROPANE / BUTANE - FLUEING WITH ONE 90° ELBOW

V (FT.) H (FT.)

1’ MIN. (305 mm) 2’ MAX. (610 mm)

2’ MIN. (610 mm) 4’ MAX. (1.22 m)

3’ MIN. (914 mm) 6’ MAX. (1.83 m)

4’ MIN. (1.22 m) 8’ MAX. (2.4 m)

5’ MIN. (1.5 m) 10’ MAX. (3.0 m)

6’ MIN. (1.83 m) 12’ MAX. (3.6 m)

V + H = 40’ MAX. (12.2 m)

NATURAL GAS

FLUEING WITH ONE 90° ELBOW

V (FT.) H (FT.)

1’ MIN. (305 mm) 3’ MAX. (914 mm)

2’ MIN. (610 mm) 6’ MAX. (1.83 m)

3’ MIN. (914 mm) 9’ MAX. (2.7 m)

4’ MIN. (1.22 m) 12’ MAX. (3.6 m)

5’ MIN. (1.5 m) 15’ MAX. (4.5 m)

V + H = 40’ MAX. (12.2 m)

PROPANE / BUTANE

FLUEING WITH ONE 90° ELBOW

V (FT.) H (FT.)

1’ MIN. (305 mm) 2’ MAX. (610 mm)

2’ MIN. (610 mm) 4’ MAX. (1.22 m)

3’ MIN. (914 mm) 6’ MAX. (1.83 m)

4’ MIN. (1.22 m) 8’ MAX. (2.4 m)

5’ MIN. (1.5 m) 10’ MAX. (3.0 m)

V + H = 40’ MAX. (12.2 m)

Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev. o • 3/13 20

Figure 12. Flueing with Two 90° Elbows

H

1

H

V

1

H

NATURAL GAS

FLUEING WITH TWO 90° ELBOWS

V (FT.) H + H1 (FT.)

1’ MIN. (305 mm) 3’ MAX. (914 mm)

2’ MIN. (610 mm) 6’ MAX. (1.83 m)

3’ MIN. (914 mm) 9’ MAX. (2.7 m)

4’ MIN. (1.22 m) 12’ MAX. (3.6 m)

5’ MIN. (1.5 m) 15’ MAX. (4.5 m)

V + H + h1 = 40’ MAX. (12.2 m)

H + h1 = 15’ MAX. (4.5 m)

PROPANE / BUTANE

FLUEING WITH TWO 90° ELBOWS

V (FT.) H + H1 (FT.)

1’ MIN. (305 mm) 2’ MAX. (610 mm)

2’ MIN. (610 mm) 4’ MAX. (1.22 m)

3’ MIN. (914 mm) 6’ MAX. (1.83 m)

4’ MIN. (1.22 m) 8’ MAX. (2.4 m)

5’ MIN. (1.5 m) 10’ MAX. (3.0 m)

V + H + h1 = 40’ MAX. (12.2 m)

H + h1 = 10’ MAX. (3.0 m)

NATURAL GAS

FLUEING WITH TWO 90° ELBOWS

V + V1 (FT.) H (FT.)

1’ MIN. (305 mm) 3’ MAX. (914 mm)

2’ MIN. (610 mm) 6’ MAX. (1.83 m)

3’ MIN. (914 mm) 9’ MAX. (2.7 m)

4’ MIN. (1.22 m) 12’ MAX. (3.6 m)

5’ MIN. (1.5 m) 15’ MAX. (4.5 m)

V + V1 + H = 40’ MAX. (12.2 m)

PROPANE / BUTANE

FLUEING WITH TWO 90° ELBOWS

V + V1 (FT.) H (FT.)

1’ MIN. (305 mm) 2’ MAX. (610 mm)

2’ MIN. (610 mm) 4’ MAX. (1.22 m)

3’ MIN. (914 mm) 6’ MAX. (1.83 m)

4’ MIN. (1.22 m) 8’ MAX. (2.4 m)

5’ MIN. (1.5 m) 10’ MAX. (3.0 m)

V + V1 + H = 40’ MAX. (12.2 m)

Page is loading ...

Heat & Glo LCOR/RCOR/PIER/ST-HVB-CE Install Manual

Heat & Glo LCOR/RCOR/PIER/ST-HVB-CE Install Manual

Related papers

Other documents