Canarm LED-SL12BK-C Owner's manual

Canarm
Brand
Canarm
Model
LED-SL12BK-C
Type
Owner's manual
Imported By: CANARM LTD., 2157 Parkedale Ave., Brockville, Ontario, K6V 5V6, Tel: (613) 342-5424, Fax: (613) 342-8437
LED-SL12BK-C
SAFETY PRECAUTIONS:
FLOOD LIGHT
OUTDOOR SECURITY LIGHT
1. TURN OFF ELECTRICAL POWER BEFORE STARTING INSTALLATION OF LIGHT FIXTURE.
2. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A
PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
3. THIS FIXTURE CAN ONLY BE MOUNTED ON A WEATHERPROOF OUTLET BOX AND IS PROVIDED WITH
A GASKET.
4. ENSURE THAT THE OUTLET BOX IS MARKED "FOR USE IN WET LOCATIONS."
5. CONNECT THE GROUND WIRE (BARE COPPER OR GREEN) FROM YOUR FIXTURE TO THE GROUND
WIRE (BARE COPPER OR GREEN) OR GROUND SCREW IN THE ELECTRICAL OUTLET BOX.
NOTE: PRODUCT MAY NOT LOOK EXACTLY AS SHOWN IN FIGURES.
TOOLS AND MATERIALS REQUIRED:
Pliers Phillips
Screwdriver
Wire Cutters
Wiring supplies
as required by
electrical code
L
I
G
H
T
I
N
G
&
F
A
N
S
E
C
L
A
I
R
A
G
E
S
&
V
E
N
T
I
L
A
T
E
U
R
S
QUESTIONS OR CONCERNS, CONTACT CANARM AT:
1-800-265-1833 (English)
1-800-567-2513 (French)
Monday through Friday 8:00 AM to 5:00 PM E.S.T.
!
“INSTRUCTIONS PERTAINING TO RISK OF FIRE OR INJURY TO PERSONS”
“READ ALL INSTRUCTIONS”
“IMPORTANT SAFETY
INSTRUCTIONS”
“SAVE THESE INSTRUCTIONS”
6. Apply caulking
around the fixture and it’s
mounting surface to
ensure a water tight seal.
1.
Assemble fixture.
Secure the lens onto fixture
using 4 screws prodivided.
Twist the fixture onto the
mounting bracket and
secure with lock nut
provided.
2.
Mount the mounting
bracket to outlet box using
outlet box screws (not
included). Make sure the
studs on the mounting
bracket are facing out from
the outlet box.
3.
Position mounting
bracket so that the fixture
will sit level once it is
mounted to the wall.
Tighten screws “A” and “B”
to hold in place.
INSTALLATION:
Mounting
Canopy
Lens
Fixture Lock
Nut
Electrical Box Screws
(not Included)
Electrical
Box
Stud
Electrical
Box
“A” “B”
Studs
House Supply
Ground Wire
Fixture
Ground
Wire
Ground
Screw
Black Wire
White Wire
4. Firmly attach the fixture
ground wire (bare copper) to
the mounting bracket with
the ground screw (by
wrapping around the
ground screw) and then
connect it to the house
supply ground wire with a
wire nut. Connect black
wire from fixture to black
wire in outlet box and
connect the white wire from
fixture to white wire in outlet
box.
Fixture is approved to -25ºC
5.
Attach mounting
canopy to electrical box
with decorative nuts.
Decorative
Nuts
Mounting
Canopy
  • Page 1 1

Canarm LED-SL12BK-C Owner's manual

Canarm
Brand
Canarm
Model
LED-SL12BK-C
Type
Owner's manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents