Playcraft Monaco Pool Table Owner's manual

Type
Owner's manual
ASSEMB
LY INSTRUCTIONS
DP03S
WARNING: DO NOT ATTEMPT TO ASSEMBLE IF PARTS ARE MISSING OR
DAMAGED. IMPROPER ASSEMBLY MAY RESULT IN DAMAGE OR SERIOUS INJURY
Please read the following instructions carefully prior to assembly.Check the parts list to
make sure you have all the parts needed for proper assembly.
assistance.
1) Your table is designed for use indoors in a climate controled environment only.
Damage can occur if the table is exposed to water, dampness, high humidity,
freezing temperatures, etc.
2) Professional assembly is strongly recommended. This assembly manual is intended to
guide an experienced slate pool table installer with the assembly process of this
for which the process is the same regardless of the cabinet type.
2) The pool table cabinet and slate are extremely heavy. Two or more people are
required for assembly.
or serious injury.
5) Only use the table for its intended purpose.
6) Damaged or worn parts may be dangerous for users and the integrity of the table.
will void the warranty.
8) Check all screws, bolts, etc. on a regular basis to ensure that they are in good working
as required with owning a slate pool table
Rio Grande
PARTS LIST
1
DESCRIPTION
PICTURE
QTY
SIZE
LEG 4 750*130*130
LONG APRON 2 2365*110*55
SHORT APRON 2 1250*110*60
LONG BEAM 2 2454*100*50
SHORT BEAM 2 1334*100*40
SLATE
1 804*1295*40
1 804*1295*40
1 804*1295*40
CLOTH 1
SHORT RAIL 2 1258*176*43
CORNER 4 106*106*43
LONG RAIL 2 2373*176*43
PARTS LIST2
PART
PICTURE
QTY
SIZE
H1 DOUBLE HEAD BOLT 8 ø10*120
H2 FLAT WAHER 8 ø10*30*2
H3 BOLT NUT 8 M10
H4 BARREL NUT 4 M10*25
H5 ANGLE IRON 8 /
H6 HEX BOLT 16 ø8*15
H7 BOLT NUT 8 M8
H8 FLAT WAHER 16 M12
H9 HEX BOLT 4 ø8*60
H10 HEX BOLT 4 ø8*40
H11 FLAT HEAD SCREW 8 4.2*40
H12
ADJUSTABLE SCREW
12 ø10*55
H13 4 ø10*75
H14 RUBBER SHIM 4 2mm*2pcs
3mm*2pcs
H15 WOODEN SCREW 12 6*70
H16 HEX BOLT 8 ø8*70
H17 FLAT WAHER 8 ø8*20
H18 SEMICIRCLE WASHER 8 M8
H19 BARREL NUT 8 M8*20
H20 HEX BOLT 18 ø10*60
H21 DOME WASHER 18 ø10*35*5
H22 LEATHER POCKET 4 /
H23 LEATHER POCKET 2 /
H24 FLAT HEAD SCREW 12 4.2*16
H25 TOUCH-UP MARKER PEN 1
Steps 1
Note: It is recommended that two or more people install this step. During the installation,
protect the parts from scratching the paint.
Steps 2
Steps 3
Note: The direction of screw head is installed as shown in the picture.
Steps 4
Note: The direction of the screw head is installed as shown in the picture. After installation,
it is necessary to measure the diagonal dimensions and adjust the two diagonal dimensions
to keep the whole frame as a standard rectangle.
Steps 5
Note: The top face of the adjusting screw is on the same level as the beam.
Steps 6
Note: If the floor is not flat, the table will be easily shacking after installation. If in this case,please use
the rubber pad H142mm or 3mm to put under the table leg and adjust it until the table frame is
in level status . This rubber pad is only used when the ground is not level enough. It is not required
for normal use.
Steps 7
Note: After put the slate above the table frame,you could adjust the slate levelers (H1213) to
adjust the level of the slate,then lock the slate levelers by nuts when the slate in good level, finally
tighten the wooden screwsH15.
Steps 8
Note: Clean the debris on the slate surface, and fill with putty and sanding if the slate
surface has uneven or any gap between the piece of slate.7.2) After cleaning the slate again,
lay the table cloth on the slate and staple it under the slate backer.
Steps 9
Note: During installation, pay attention to protect the top rail from scraping, and make sure
that the side of the top rail is in the same plance .
Steps10
Note: there must be at least 2 people working at the same time to turn the table rail by 180
degrees, and put it above the slate.
Steps11
Note: The leather pocket can only be installed from the bottom to the top, so as not to
scratch the top of leather surface.
Complete
Customer Service
Global Merchants, Inc.
12 Lunar Drive
Woodbridge, CT 06525
*Back-up Accessories 1Touch-up Marker PenH25 Usage: covers scratches in order not to see the
inner material color under painting color.Repairs light scratches beyond the finish layer.
Directions:
1):Clean the scratching with clean dry soft cloth before applying.
2):Shake the marker pen well before using.
3):Test it on paper before use.
4):Apply marker with smooth strokes in the direction of the scratching or wood grains,you can only
paint in one direction of the first time. If the color is too dark at the first time,please quickly wipe it with a
clean dry soft cloth or kitchen paper in order to lighten the color a little; If the color is too light, quickly
repaint it until the color is closer to the original color.
5):Please cover the marker pen with it’s cap after use and keep it for future.
CAUTION:
1.Keep out of reach of Children.
2.The color of this marker pen is only similar to the original product color, but not same,please consider
whether you would like to apply it really after you test it’s color on a paper before use.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Playcraft Monaco Pool Table Owner's manual

Type
Owner's manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI