Vemer RX1-8A User manual

Brand: Vemer

Model: RX1-8A

Type: User manual

Mod. RX1-8A

Dimensions

Connection diagram

35.6

87.8

5 6 87

8A / 250V CA

Out

Connection examples

Out

LOAD

Circulation pumps,

burners, solenoid valves.

Motor-operated valves.

User Manual

REMOTE ACTUATOR MODEL RX1-8A

Read all the instructions carefully

Theremoteactuator

RX1-8A

isanindependentlymountedautomaticcontrolfor

heatingandairconditioningapplications,designedforradiocomunicationswith

Athena

programmable thermostat and

Klio

digital thermostat

Itprovidesatype1Bactionsanditisdesignedforhouseholdandsimilarusewith

overvoltage category III (EN 61010-1) and normal pollution level (EN 60730-1).

SAFETY WARNINGS

During product installation and operation, the following safety instructions

should be respected:

1) The appliance should only be installed by technical person support

2) Take out power supply during product installation

3) Do not power or connect the instrument if any part of it is damaged

4) Follow the connection diagrams descripted on this manual and over the

product

Code Model Description

VE015400 RX1-8A Remote actuator

CARACTÉRISTIQUES TECHNIQUES

• Powersupply:230VAC(-15%/+10%)50/60Hz

• Outputs:

 -1relay8A250VAC(resistiveload)

- external antenna (on request)

• Operatingtemperature:0°C÷50°C

• Storagetemperature:-10°C÷65°C

• DIN-railmounting

• Protectiondegree:IP40

USE

DISPLAY AND CONTROLS

1–GreenLEDoperationfunction

2–RedLEDrelayfunction

3–ResetandprogrammationSETBUTTON

OPERATION

• Instartingphase,theredLEDashesestwicefor

someseconds(switchingon-sequence).

• Attheendoftheswitchingon-sequence,the

greenLEDsignalnormaldeviceoperationand

theredLEDrelaystatus(lighton=relayON).

• Theremotecontrol(relaycommutationON/

OFF)requestfromKlio digital thermostat and

Athena programmable thermostat take place

onlyafterchannelsetting-up.

• Theradioconnectionbreakdownformorethan

15minutesbetweenthetransmitterandthe

receiverdisconnectstherelayandtheredLED

lightened.Restoreofoperationsisautomatic.

Channel setting-up

° Duringnormaloperation,presstheSETkey-buttonforalmostthreesecondstoenter

inmodality-conguration.GreenLEDswitch-off,redLEDash.

° Theappliancekeeponmodality-congurationforamaximumof60secondswithin

theactuatorshouldreceiveastringconguration(seeAthenaand/orKlioinstructions

forstringstart-upmodality).

° Onreceiptofstring,channelissetted-upandtheactuatorisonstandardfunctioning.

° Forre-settingup,repeatingtheprocedure.

• Toresetchannelsetting-up,plugintocongurationmodalitywithSETbutton,thenpush

thesameoneforthreesecondsandwaitforgreenledswitchingon.Anewchannelsetting

up cancels the previous conﬁguration.

STANDARDS REFERENCE

ConformitywithEUDirectives:

2006/95/EC (LowVoltage)

2004/108/EC (E.M.C.)

isdeclaredwithreferencetothefollowingstandards:

Safety: EN 60730-1

Electromagnetic compatibility: EN301489-1/3andEN300220-3

OPEN

V3IS00378-010-102009

Vemer RX1-8A User manual

Vemer RX1-8A User manual

Related papers

Other documents