Anova L1446 is a 6-Seat Latitude Table with Contour Seats. It is a versatile piece of furniture that can be used for a variety of purposes, both indoors and outdoors. The table is made of durable materials and is easy to assemble. It features a sturdy steel frame and a tabletop made of high-pressure laminate. The contour seats are comfortable and supportive, and they are made of a durable plastic material. The table is also easy to clean and maintain. It can be used for dining, entertaining, or simply relaxing.
Anova L1446 is a 6-Seat Latitude Table with Contour Seats. It is a versatile piece of furniture that can be used for a variety of purposes, both indoors and outdoors. The table is made of durable materials and is easy to assemble. It features a sturdy steel frame and a tabletop made of high-pressure laminate. The contour seats are comfortable and supportive, and they are made of a durable plastic material. The table is also easy to clean and maintain. It can be used for dining, entertaining, or simply relaxing.
anovafurnishings.com
888.535.5005 tel
OR
ASSEMBLY INSTRUCTIONS
L1390 6-Seat Rendezvous Table with Flat Seats
L1392 6-Seat Rendezvous Table with Contour Seats
L1444 6-Seat Latitude Table with Flat Seats
L1446 6-Seat Latitude Table with Contour Seats
TOOLS NEEDED:
Ratchet with 1/2” Socket•
1/2” Open End or Box End Wrench•
5/32” Allen Wrench•
Rubber Mallet•
6 x
Plug
60 x
5/16 X 1.0”
Hex Head Bolt
ASSEMBLY:
The assembly is a two-person operation.
Inspect the shipping container contents for damage and to determine that all components and hardware are present.1.
Assemble the Table over the shipping packaging or padded work area to avoid scratching the product.2.
NOTE: Before assembling the Nuts to the Bolts, it is recommended that a light oil or petroleum jelly be applied to the screw threads.
Open the Hardware package and nd the six black plastic Plugs. Insert a Plug in the hole on the bottom of each of the Seat 3.
Supports. Use the Rubber Mallet to seat the Plugs.
TABLE COMPONENTS:
6 x Seat Support1 x Lower Leg
Bracket
60 x
5/16” Flanged Nut
OR
1 x Table Top
ASSEMBLY HARDWARE:
120 x
5/16” Flat
Washer
6 x Seat Mount
14 x
1/4” Flat Washer
1 x Table Top Pan
Plug
Seat Support
14 x
1/4 x 1.5” Button
Head Allen Screw
6 x Flat or
Contour Seat
Rendezvous models shown
seat shape and pattern may vary
2 of 4
Locate the Lower Leg Bracket. Install a 5/16” 4.
Flat Washer on one of the 5/16” Hex Head
Bolts and insert the Bolt through one of the
mounting holes in the Lower Leg Bracket and
into the lower mounting hole in one of the
Seat Supports. Place a 5/16” Flat Washer and
Flanged Nut on the end of the Bolt and tighten
nger tight.
Table Top Pan
5/16” Hex Head Bolt
Seat Support
5/16” Flat Washer
Seat Support
Flanged Nut
5/16” Flat Washer
Seat Support
Lower Leg Bracket
5/16” Bolt
5/16” Flat
Washer
Flanged Nut
5/16” Flat Washer
Packing cardboard or
other so work surface
Repeat Step 4 for the remaining 5.
Seat Supports using 5/16” Bolts with a
5/16” Flat Washer on the top and bottom
and Flanged Nuts to secure. Leave the
hardware nger tight until aer the Table
Top Pan is secured (Step 7).
Locate the Table Top Pan and place it on top of the platform created by the raised ends of the Seat Supports. Adjust the 6.
placement of the Table Top Pan until one set of mounting holes in the Pan align with the corresponding set of mounting holes in
one of the Seat Supports.
Place a 5/16” Flat Washer on the end of one of the 5/16” Hex Head Bolts and insert the Bolt through the Pan mounting hole in
the inner bolt circle and through hole in the Support. Fasten the Bolt using a 5/16” Flat Washer and Flanged Nut on the bottom
of the Bolt. Leave the Bolt and Nut nger tight. Repeat this for the remaining ve 5/16” Hex Head Bolts. You may have to adjust
the Seat Supports or the Table Top Pan in order to get the mounting holes to align.
3 of 4
Place a 1/4” Flat Washer on the end of one of the Button Head Allen Screws and insert the screw through one of the Pan 7.
mounting holes in the outer bolt circle and into the corresponding threaded hole in the Seat Support. Leave the Screw nger
tight. Repeat this for the remaining ve 1/4” Button Head Allen Screw locations in the top of the Table Top Pan. You may have to
adjust the Seat Supports or the Table Top Pan in order to get the mounting holes to align.
Aer all the Button Head Allen Screws are installed, tighten all of the hardware in the Lower Leg Bracket and in the Table Top
Pan. Be careful not to over tighten the Button Head Allen Screws; the inserts they thread into could unseat and begin to spin
with the Screw.
Seat Mount
Seat Support
Mounting Plate
Table Top Pan
5/16” Hex Head Bolt
Button Head
Allen Screw
1/4” Flat Washer
Button Head
Allen Screw
1/4” Flat Washer
Seat Mount
5/16” Flat Washer
Flanged Nut
5/16”Flat Washer
Seat Support
Mounting Plate
Locate one of the Seat Mounts. Position the Seat Mount on the lower end of one of the Seat Supports so that the mounting 8.
holes in the Seat Mount align with the mounting holes in the Seat Support Mounting Plate. Install four 5/16” Hex Head Bolts
with 5/16” Flat Washers (top and bottom) and Flanged Nuts.
Install the remaining Seat Mounts in the same manner.
Do not drag the assembled unit across any surface.•
This product requires only periodic cleaning with a sponge and a solution of mild detergent and water to •
remove surface dirt. Do not clean with a solvent or petroleum based products.
Furniture must not be used other than for its intended purpose and should be inspected regularly for loose, •
missing, or broken hardware, and general instability.
Furniture that is damaged or appears to be unstable must be removed from service and be repaired or replaced. •
Repairs must be made using only factory authorized parts and methods.•
WARNING
CARE AND
MAINTENANCE
211 North Lindbergh Blvd.
St. Louis, MO 63141
tel: 888.535.5005
web: anovafurnishings.com
11/2012
Li the Table Top and move it over the top of the Table Top Pan. Rotate the Table Top until the square frame on the bottom of the 9.
Table Top matches the orientation of the Table Top Pan. Carefully lower the Table Top down onto the Table Top Pan.
Secure the Table Top to the Table Top Pan using the remaining eight Button Head Allen Screws (2 screws on each side) with a
1/4” Washer on each of the Screws. You may have to li the Table Top slightly to get the holes to align.
Leave the Screws nger tight until all the Screws are started, then use the 5/32” Allen Wrench to tighten the Screws. Be careful
not to over tighten the Screws; the inserts they thread into could unseat and begin to spin with the Screw.
5/16” Flat
Washer
5/16” Hex
Head Bolt
5/16” Flat
Washer
Flanged Nut
5/16” Flat Washer
5/16” Hex Head Bolt
5/16” Flat Washer
Flanged Nut
Contour Seat
OR
Flat Seat
Table Top
Table Top Pan
1/4” Button
Head Allen Screw
1/4” Flat Washer
1/4” Button
Head Allen Screw
1/4” Flat Washer
Place one of the Seats (Flat or Contour) over one of the Seat Mounts. Use four 5/16” Hex Head Bolt with 5/16” Flat Washers 10.
(inside and outside) and Flanged Nuts.
Install the remaining Seats in the same manner.
Move the Table to the location where it will be used.11.
Aer two weeks, retighten all hardware.12.
-
1
-
2
-
3
-
4
Anova L1446 Assembly Instruction
- Type
- Assembly Instruction
Anova L1446 is a 6-Seat Latitude Table with Contour Seats. It is a versatile piece of furniture that can be used for a variety of purposes, both indoors and outdoors. The table is made of durable materials and is easy to assemble. It features a sturdy steel frame and a tabletop made of high-pressure laminate. The contour seats are comfortable and supportive, and they are made of a durable plastic material. The table is also easy to clean and maintain. It can be used for dining, entertaining, or simply relaxing.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Anova L1447 Assembly Instruction
-
-
-
-
-
-
-
-
-
Other documents
-
Invacare ASBA User manual
-
Ezgo RXV SHUTTLE 2+2 Service & Repair Manual
-
Toro Center Trencher, RT1200 Traction Unit User manual
-
Woods Equipment BW15LH User manual
-
Gorilla Playsets 01-0004-AP Operating instructions
-
Gorilla Playsets 01-0006-AP Operating instructions
-
-
Woods PRD6000 User manual
-
Royal Enfield Himalayan User manual
-
