Robotouch RBT03 User manual

Brand: Robotouch

Model: RBT03

Category: Treadmills

Type: User manual

Robotouch RBT03 is a high-quality motorized treadmill with a variety of features to help you get the most out of your workouts. With a powerful 1500W motor, it can reach speeds of up to 14 km/h, making it ideal for both walking and running. The large running belt (122 x 42 cm) provides plenty of space to move, and the multi-layer anti-vibration device ensures a smooth and comfortable ride.

The Robotouch RBT03 also features a range of built-in programs to help you stay motivated. There are six preset programs, each with a different time, speed, and incline setting. You can also create your own custom programs or use the manual mode to set your own speed and incline.

robotouch.

RBTO3

Foldable Motorized Treadmill

illli5 _t16 rj5

. Rated voltage: 8.3A

. Motorpower:1500W

. Scope of operating speed: 1 - 1 4 (km/h)

. Scopeoftimedisplay:0:00-99:59 (min: s)

o Scope of distance display: 0.00-99.9 (km)

. Scopeofheartrate:50-200 (bpm)

. Scopeof caloriedisplay: 0-999 (calories)

. Floorarea: 165X74x132cm

. Effective usable floor area: 122x 42 cm

Features

X Oversized blue-backlight LCD information display window

X 6 running procedures.

X Fat measuring function.

X Six speed direct election function

X Manual gradient adjustment

X Speed regulating through handle and StarUStop functions

X High power and tone quality sound, audio input function

X Hydraulic pole folding attached with newly set hydraulic pole casing hook protection device

X MultiJayeranti-vibrationdevice

X Over current and overload protection device

II. Product introduction

Electronic meter

Upright

pole-connecting pipe

Running

belt Edge Rear regulatlng box

Under frame \lManual qradlont adjustment

Ill. Product explosion diagram

@./

L.@ P

Yq/

lV. Particular sheet of explosion diagram

S/N Part name Qtv. S/N Part name Qtv.

Electronic meter I29 Running frame 1

2 Handle-type hear rate meter 230 Bulkhead (30x15) 2

3Tear-proof armrest 231 Air spring casing 1

4Armrest bulkhead 232 Running belt lower cover 1

5Edge 233 Treadle housing 1

6 Running belt 134 Anti-loosing clip 1

7Motor cover 135 Air pressure bar I

8Motor belt I36 Rectangular 40 x 80 inner

bulkhead 2

IElectronic control board 137 54 roller 2

10 Fore drum 138 MB (O16 x 1 .2) small flat washer 24

11 MB x '1 00 hexagon socket pan

head screws 339 Foot pad 4

12 M6X40 cross countersunk head

screws 640 M8 X 50 hexagon socket pan

head screw 2

13 Running board 141 Under frame 1

14 Edge spacer buckle 642 Black gasket 2

15 Fuse base 143 M'|2X80 hexagon socket Pan

head screw 2

16 Line clip 144 MBX 16 hexagon socket pan

head screws 4

17 Switch 145 M8 (O24x2.0) curved small

washer 4

18 M8 x 45 hexagon socket head

cap screw 146 Upright pole 1

19 Rear drum 147 Motor base (Zhongyang) 1

20 M8 x 75 hexagon socket head

cap screw 348 M8 x 30 hexagon socket pan

head screw 1

21 Right rear regulating box 149 MBX30 hexagon socket head

cao screw 4

22 G25 bulkhead 250 DC motor 1

23 Anti-vibration pad 651 Upright pole-connecting pipe I

24 Left rear regulating box 152 Decorative cover of upright pole

horizontal oioe 4

25 Manual gradient adjustment ,| 53 M5 x 20 big flat head cross

tapDinq screw 4

26 Bulkhead of gradient adjustment

nine 254 M6 (O18 x 1 .0) curved big

washer 4

27 M8 stop nut 755 M8 X 55 hexagon socket head

cap screw 4

28 M8x45 flat head cross screw 2

-4- -5-

V. Assembly step

All parts of elechic treadmill have been strictly assembled and debugged before the exworks. An

elechic treadmill can be easily assembled into if the installation is carried out by observing following

steps.

Step l: Open the packing box, take out the

treadmill, insert the left upright pole (there is no

connector lug in the bottom of the upright pole)

into the under frame, and use a pan hexagon

socket head cap screw (M8x16, with curved

washer) for fixation, and two pan hexagon

socket head cap screws (M8 x 55, with flat

washer) for locking. Next, couple the line of the

right upright pole (there is connector lug in the

bottom of the upright pole) with the line of

under frame, then insert the under frame. Use

a pan hexagon socket head cap screw (M8X

16, with curved washer) for fixation, and two

pan hexagon socket head cap screws (M8 x 55,

with flat washer) for locking.

Step ll: Apply the decorative cover of the

upright pole horizontal pipe to the upright pole

horizontal pipe. Then, use two pan hexagon

socket head cap screws (M8 X 1 00, with curved

washer) to fix the upright pole horizontal pipe.

Step lV: unscrew the screws (M6x10) which

fixes the anti-loosing clip.

Step lll: Couple the wire in the left and right

handles with the wire in the meter. Use four

tapping screws (M5X20, with curved washer)

to fix the meter, then insert the wire end into

the holes of the long slot of the armrest pipes.

5.3-Under the standby state, press the "Mode" Key to enter the Time countdown Mode and the

Time Window will display "'15:00" and flash. The exercise time can be set by pressing the "Speed-up

and Speed-down" Key and the setting range is 5:00-99:00. Press the 'Start" Key after the setting is

accomplished, and then the treadmill will start to run after 3s. The speed can be adjusted by pressing

the "Speed-up and Speed-down" Key or Speed shortcut Key; Pressing the "Stop" Key will stop the

treadmill. Time countdown will decrease progressively from set value to zero, when the countdown

turns to zero, the treadmill will slow down steadily to stop, and enters into standby state after it

completely stops.

S.4-Under the standby state, continuously press the Mode Key twice to enter the Distance

countdown Mode, the Distance Window will display'1.0" and flash, pressing the'Speed-up" and

"Speed-down" Key can set the exercise distance, and the scope of distance setting is 0.5-99.9. Press

the "Start" Key again after the setting is accomplished, and then the treadmill will start to run after 3s.

The speed can be adjusted by pressing the "Speed-up and Speed-down" Key or Speed shortcut Key.

Pressing the "Stop" Key can stop the treadmill. Distance countdown will decrease progressively from

set value to zero, when the countdown turns to zero, the treadmill will slow down steadily to stop, and

enters into standby state after it completely stops.

S.S-Under the standby state, continuously press the Mode Key three times to enter the Calorie

countdown Mode, the Calorie Window will display "50' and flash, pressing the "Speed-up and

Speed-down" Key can set the calorie, and the setting range of calorie is: 10-999. Press the "Start"

Key again after the setting is accomplished, and then the treadmill will start to run after 3s. The speed

can be adjusted by pressing the "Speed-up and Speed-down" Key or Speed shortcut Key. Pressing

the "Stop" Key can stop the treadmill. Calorie countdown will decrease progressively from set value

to zero, when the countdown turns to zero, the treadmill will slow down steadily to stop, and enters

into standby state after it completely stops.

6. Display scope of the various values:

Parameter setting lnitial Setting initial value Setting range Display range

fime (minute: second) 0:00 15:00 5:00-99:00 0:00-99:59

ipeed (KM/H) 1.0 N/A N/A 1.0-14

)istance ( KM )0 1.0 0.5-99.9 0.00-99.9

leart beat (times/min) P N/A N/A 50-200

lalorie (kilocalorie) 0 50 10-999 0-999

7. Programming Mode

The system is provided with a total of 6 buillin programs (P1-P6), under the standby state,

press the "Programming" Key, the Distance Window will display 'P1-P6', the .TIME' Window

displays the preset time "10:00" and flashes while the favorite program is selected; Press the

"Speed-up and Speed-down" Key to set the required exercise time (setting time is 5-99 minutes),

then press the "Start" Key to start the built-in program. The built-in program is divided into 10 sections.

The operating time in each section=setting time /10. When the program enters into next section, the

system gives a sound of 'Bi-Bi- Bi", and the speed of the system will change along with the program

section. Meantime, the speed can be changed through pressing the "Speed-up", "Speed-down" or

Speed shortcut Key. But when the program enters into next section, it will return to the speed of that

section. When a program is completed, the system gives a sound of "Bi-Bl- Bi". The keadmill

slows down till to stop and enter to standby state.

Table for Built-in Program:

\\ntervar

Program -\-\ Set time/10 = The operating time in each section

I23456 7 8o10

P1 Speed 33 6 5 5 5 4 443

P2 Speed 334455 5 664

P3 Speed 335 6 7 8 6 4 33

P4 Speed 3666777333

P5 Speed 388I876322

P6 Speed 25 6 7777733

8. Fat measuring Mode:

Under the standby state, continuously press "Programming" Key to start the detection function

for physical indexes (FAT), or press "Mode" Key to enter inlo interfaces F-1,F-2 F-3, F-4 and F-5

(F-1-gender, F-2-age, F- 3-body height, F-4-body weight and F-5- physical detection). The

parameters for 01-04 are sei up by pressing "Speed-up (+)'and 'Speed-down O" Key (parameters

are shown in the following table). After the sefting, the "Mode" Key is pressed to enter into F-5

Physical Examination lnterface. At this time, you should hold handle-type heart rate metering plate

with both hands. Your physical indexes will be displayed in 4-5s. Check whether the displayed

values are in accordance with your body weight and height. The physical indexes (FAT) are used to

display the relation between the body weight and body weight rather than body proportion. The FAT

is applicable to any male and female and can provide the weight adjusting basis for people along

with other healthy indexes. ldeal FAT should be in range of 20-25.|t means too thin when the value

is lower than 19, the overweight when the value is in range of 25-29 and the obesity when the

value exceed 30. said for reference and cannot be used as

F-01 Gender Male (01) Female (02)

F-O2 Age 10-----99

F-03 Body height 100----220

F-04 Body weight 20-----150

F-05

Physical index <19 Slightly thin

Physical index =(20---2s\ ldeal

Physical index =(25--29) Overweight

Physical index >30 Obesity

medical data.).

9. Functions of safety switch:

Under any state, removing the safety switch can emergently stop the treadmill. At the emergency

shutdown of the treadmill, all window displays and the buzzer gives an alarming sound of

"BB'. At this time, any operation (excluding shutdown) cannot be carried out for the treadmill. After

the safety lock is correctly reinstalled, the treadmill enters into the standby state again and waits for

input command.

-8- -9-

10. Sleep function

The system is provided with power saving function. Under the standby state, if no key

commands are inputted withln 10 minutes, then the system will enter power save mode, and the

display will be closed automatically. The system can be restarted again by pressing any button.

11. Functions of Heart-beat measurement:

The heart-beat displav is onlv used as the reference value rather than medical data. During the

measurement, hold the heart rate sheet firmly with both hands, and the whole procedure will take

few seconds.

Vll. Use method and safety protection for treadmill

1. Debugging of treadmill

1 .1 After the installation is completed, position the safety switch to the corresponding position of

electronic meter.

't.2 Before the powering, inspect whether the power ground wire is well grounded and pull the

running belt with hands to check whether it can run flexibly without any abnormal sound.

1.3 Plug in the power supply and open the power supply lock. Then, all windows on the

electronic meter show the initial values and the running belt is still.

1.4 Press the "Start" Key and the treadmill starts operating at a low speed (the operating

speed is km/h). Observe whether the treadmill and electronic meter can operate normally.

'1.5 Press the "Speed-up" Key, "Speed-down', "Gradient ascending" and "Gradient descending'

Key to observe whether the regulation is normal.

1.6 Press the "Stop" Key or turn off the safety switch, and the treadmill will stop operating. Turn

off the power switch and unplug the power supply.

2. Operating instructions

After being debugged, the electric treadmill can be put into use:

2.1 Plug the power supply in the household 220V outlet. The outlet must be orovided with

appropriate qroundinq wire.

2.2 Emplace the safety lock and press "Start" Key, and then the running belt will operate slowly

(the speed is about 1 km/h). The speed per hour is displayed on the meter.

2.3 lf the treadmill needs to be accelerated, feet, loosen the air spring casing, and

press the "Speed-up' Key and the then slowly set the ireaimill level in

buzzer's "tick" indicates one level up. order, as sirown in the following figure:

The maximum speed per hour is

14kmlh^

2.4 lf you cannot wait for the deceleration

while running on the treadmill at a high speed,

you can pull out the safety switch and the

treadmill will immediately stop.

2.4. When the exercise is ovel press the

"Stop" Key after the speed is slowed down, and

the treadmill will slowly stop.

2.5 Folding operation: During the folding

operation, restore and stop the

treadmill firstly, and switch off the

power supply. Unplug the power

supply in the front of treadmill, please

be sure that the air spring casing is

firmly stuck, then remove or leave the

treadmill. When the treadmill is placed

down, stamp the air spring casing with

3. Safety protection for treadmill

3.1. ln any emergency, as long as the exerciser turns off the safety switch, the treadmill will be

power off. Therefore, when you are exercising, please be sure to clip the safety switch on

the appropriate position the on your clothes to ensure the safety.

3.2. When the treadmill belt skids or the running belt is stuck, the motor will stop in about 5s.

Vlll. Precautions

1. Circuit

1.1 Avoid using other electric appliances in the same power supply circuit. The power supply

circuit must be able to supply over 8.3A electricity current.

1.2 lt is required that the service voltage should be in the range ol 220v!10o/o. The voltage

beyond this range may lead to the abnormal operation.

'1.3 After being used, the treadmill should be immediately unplugged.

1.4 ln Winter, certain humidity should be kept indoors to avoid strong static electricity.

1.5 lf the power wire is damaoed after use. please qo to specified products distributor for

replacement or purchase.

2. Placing environment

2.'1 lt is only proper for the treadmill to be placed indoors for protection against humidity. lt is

forbidden to splash water on the treadmill. lt is forbidden to place any foreign materials on

or inserted them in the treadmill.

2.2 During the operation of the treadmill, the motor will generate a small number of sparks, so

the treadmill should be placed at a drafty place and kept away from explosives.

2.3 When the treadmill is used, ensure its fore and rear feet reliably contact the ground. lf the

ground surface is uneven, it should be stably padded with carpet or rubber plate.

2.4 Pay attention to the interior hygiene usually to reduce indoor dust because its sensibility

may be influenced by the dust adhered on the electronic components.

3. Precautions before or during exercise

3.1 For your safety, wear sports clothes and select suitable sports shoes when using the

treadmill. lt is strictly forbidden to exercise on the treadmill with bare feet.

3.2 lt is not allowed for two or more persons to do exercises on the treadmill at the same time.

3.3 Prepare a towel before running to prevent sweat from dropping on the running belt and

being thrown into the enclosure to damage the electric appliance.

3.4 The beginner can get on the treadmill only after he stands on the edge to test several times

with one foot and feels capable of keeping up with the speed of the running belt.

3,5 The treadmill has enough motor power. ln principle, the zero start can be realized, but to

extend the service life of the treadmill, it is suggested that you should stand on both edges

of the treadmill and get on it for exercise after the normal start.

3.6 lt is strictly forbidden to get on and off from the rear end as it is very easy for people to

tumble in such way.

3.7 The strength should be equal when the hands are on the armrests and run on it straightly

to avoid belt deflection.

3.8 When people run in a normal state, the two hands should be moved from the armrests. The

arms can be swung boldly so that the exercise result will be better.

3.9 The stop lock should be pressed when get off the treadmill. Don't get off the treadmitl until

the running belt stops completely.

3.10 Keep the child away from the running treadmill for fear that the hand or the clothes may

clamped by the running belt to cause serious injury.

3.11 It is strictly forbidden to touch the working running belt by hands.

4. Additional precautions

4.1 The cardiac should not use the electric treadmill alone.

4.2 Determine the running speed according to your physical conditions; and the sick should not

use the treadmill or use it under the instruction of a doctor.

4.3 The heart rate sensor is not a medical facility and the detection results are for reference

only.

-10- -11-

lX. Daily servicing and maintenance of electric treadmill

During the daily use of the treadmill, the following should be noted for the maintenance.

1. Keep the treadmill clean

1.1 The service life of the treadmill can be significantly extended by keeping clean. Often wipe

the running board and footboard exposed on the two sides of the running belt. Reduce

long-term accumulation of the dust and dirt under the running belt.

'1.2 The running belt can be wiped with soft cloth dipped with soapsuds. Don't let the water flow to

the bottom of the running belt and into the shield.

'1.3 Regularly check each bolt and nut. Please tighten and fix them immediately with tools if

they are loose.

'1.4 Regularly check whether the groove of the motor belt is clean. lf there are residual, they

must be cleaned off to avoid unnecessary vibration when it is used.

1.5 Regularly clean the electric control system and the dust surrounding the motor to ensure

normal operation of the treadmill.

2. Lubrication

2.1 A bottle of special lubricating oil for running board is attached. Running board surface

should be evenly lubricated with special lubrication regularly to avoid the damage of running

belt and running board caused by the temperature rise due to the friction between them, and

to reduce the load of the motor. (Note: the child should not play with it in fear of eating by

mistake)

2.2 After the treadmill has been used for a while, the running belt and running board should be

lubricated with the special lubricant. The lubricating time interval is different according to the

references are shown

are shown below:

Usaoe time of treadmill Lubricatinq time interval

Less than 3 hours usaoe time per week Once for three months

3-6 hours usaqe time oer week Once for one month

More than 6 hours usage time per week Once for ten davs

:read )ricating method: Loosen the right and left

nill with sneciel t6nlc lift thc n rnnind hall adjustment bolts at the rear

special tools, right and left adjustment bolts at the rear end of the

running belt about 10-15cm, pour a good amount of

special lubricating oil on the top surface of the running board, and smear it evenly and

tighten the running belt. (For adjustment method, see the "Adjusting method for the tightness

of running belt") The over lubrication should be avoided. As for the lubrication, it is by no

means "the more the bette/'. Please remember: reasonable lubrication is an important factor

to extend the service life of the treadmill!

3. Judgment for friction:

The frictional force of the running board and running belt can be increased by uncleanness or

reduction of lubricant, which may damage the motor and control panel. The excessive frictional

force is characterized with followings:

3.1 Under the power off condition, it is arduous to drive the belt by feet, or even the belt

cannot be driven;

3.2 The treadmill runs at an intermediate speed. The running belt completely stops as soon

as the safety switch is turned off;

3.3 The increment of frictional force may cause the damage of motor or control panel, short

circuit, tripping, fuse burn-out, etc.

4, Adjustment for the tightness of running belt:

4.1 Although all treadmills have been adjusted at exworks, the running belt may become loose

after the treadmill is used for some time. The maintenance is mainly carried out by the user.

lf the running belt is too loose, the skidding phenomenon of running belt and drum will

occur when you step on the running belt. But excessive tightness is not good either

because it may damage the motor, running belt and drum, increase the running noise of the

treadmill, etc. ln general condition, it is better to lift the two sides of running belt 5-6cm

away from the running board.

4.2 Judgment method for tightness of running belti

Adjust the treadmill speed to 1.5 km/h,grasp the armrest forcefully with both hands and

prevent the operating of running belt with feet. At this time, if-the-runnjng-b€ltstgp€-nrming,

thejtonl^drumcontinues"runnin$ but the running belt continues running after being released,

indicating that the running belt is excessively loose. Meanwhile, the user may feel the halt at

sometimes, and the long-term use under the loose state may shorten the service life of

running belt. Therefore, adjustment should be done timely.

4.3 Adjusting method for the tightness of running belt: After the treadmill is used for some time,

the halt may be felt while you are running on it, which is caused by the excessive loose

running belt. The tightening adjustable bolt of the right and left rear regulating box is used to

ad,ust the tightness and deflection. lt is the core component of the adjustment of the

complete treadmill.

Adjusting method (note: the clockwise means tightening and the anticlockwise means

loosening. All the tightening and loosening as shown below stand for clockwise and

anticlockwise respectively.) After the treadmill is used for some time, the running belt will get

extended slightly. lf you feel the skidding running bet, it shows the running belt is too loose.

Thus, tighten the adjustable bolts of rear cover at both sides at the same time by 1/4 circle

until no skidding or halt is felt while you are running on the treadmill.

Special attention: As for the running belt, it is not the tighter the better. The tightness should

be adjusted as required. The service life of the running belt may be shortened if it is too tight.

5. Adjustment for deflection of running belt:

As for all treadmills, although the running belt has been adjusted at exworks, the running belt

may suffer the deflection after the treadmill is used for some time. This is attributed to following

reasons:

5.1 The treadmill body is placed unevenly.

5.2 While exercising on the treadmill, the user fails to run on the central position of the running

belt.

5.3 The strength of user's feet is uneven.

5.4 Adjustment for deflection: lt only takes a few minutes to recover artificial deflection by

no-load operation. As for the non-recoverable deflection, the running belt adjusting bolts

should be adjusted with the auxiliary special tools by half a circle. For example, if the

deflection is leftward, clockwise adjust the left adjusting bolts or anticlockwise adjust the

right adjusting bolts, and if the deflection is rightward, clockwise adjust the right adjusting

bolts or anticlockwise adjust the left adjusting bolts. The defleclions of running belt are

mainly maintained and repaired by the user. As the deflection may seriously damage the

running belt, the deflection should be timely corrected if any.

6. Adjustment for motor belt:

6,1 As for all treadmills, although the motor belt has been adjusted at exworks, the running belt

may suffer the halt after the treadmill is used for some time, because the motor belt gets loose.

6.2 Method for judging the tightness of motor belt: Adjust the headmill speed to 1.5 km/h, grasp

the armrest forcefully with both hands and prevent the operating of running belt with feet. At

this time, if-the"funning-hejt"and-frant-drum-sJop-runoing-simuttaneousjy^ but the running belt

continues running after being released, indicating that the motor belt is excessively loose.

Meanwhile, the user may feel the halt at sometimes, and the long-term use under the loose

state may shorten the service life of motor belt. Therefore, adjustment should be done timely.

6.3 Solution: Use special tools to clockwise adjust the motor belt adjusting bolts for several circles

until the user cannot feel the halt. This adjustment is mainly carried out the by user.

Adjusting method for motor belt: Clockwise adjust the motor belt adjusting bolts by half a circle

with auxiliary tools.

Special attention: As for the motor belt, it is not the tighter the better. The tightness should be

adjusted as required. The service life of the running belt may be shortened if it is too tight.

-12- -13-

Phenomena

(abnormal Po6sible reasons Examlnation m6thod Fault elimination

Pryer fallure

The electronic

meter does not

1. The plug or droPout 1. lnspecl whether the plug and drop-out

line ln each section are firmly lnsened. l. Fimly insert the plug and drop{ul

line.

2. The power switch is not 2. Inspect whether the power switch is

tumed on. 2. Restart the power supply.

The motor does

not work.

1. lhe related line of

control motor is out of

order. 1. lnspect whether the line of @ntrol

moto. is @rectly and lirmly inserted 1. Re-insert the control line of the

motor,

2 The START KEY b rct 2. lnspect whether the key is out ol order

or without stadlho swilch 2 Press the START KEY agaln to test

3. t he sarety switch is not 3. lnspect whether the safety switch is 3, Reset safety swltch.

4. The plug ofthe motor is

l@se or the motor is out 4, lmplement the exchange test to

inspect the fault of motor 4, Repla@ the motor

5, Ihe power supply or

the specification of the

control (AC (l'10/230) V) 5. lnspect and confirm lhe specification. 5, Select correct specifi€tion ahd

crry out the test again.

No speed

response SENSOR induction is

bad.

1 lnspect the distance and th€ position 'l Adiust the distance within sm/m.

2lnsrect whether the wire rod ls short Replace the wire rod or SENSOR.

3 lnspect whether the connectors oI the

wire rod are flrmlv connecled 3. Rensert the connectors of the wiae

Shokes are

imperf@t and the

shadow exists.

The screre of PA carcuit

boards are not tightened

up or the Connector is

in.dredlv hh.ad

Dismount the shell and press PA circuil

board to check short circuit or failing. Replace the connector and tighten up

the screws.

1 SENSOR induclion is 1. lnspec{ whether the wire rod is short

circuit or falls off, 1 . Re-inshll the wie rrl

Do not dlsplay the

heart beat. bad. 2 lnspect whether the connectoE are

n6.dv .6nnp.Jcd 2. Reinsefr the wire rod.

2 The body induclion ls 3 Both hands are sljghtly wet or rub

-^ai6.r 6-^h ^rha. 3 Cary out the measurement aoaln.

E01

1. The motor €n opeGte

atter being started. The

motor Slgnal @nnot be

detected for @ntinuous

4s, and the treadmill

1. lnspect whether lhe photoelectric

sensor and the wire rod is open chcuit or 1. Replace the photoelectric sensor

rnd raJnc.d tha .^hhart^6

2. lnspecl whether the connectors are

correctly inserted, and lhe magnetlc

<cn.^r i< hr k6n ^. d,m.daa 2. Replace the photoelectric sensor,

The molor does not rcrk

after being started, and

displays E01 ln 4s.

3. lnspect whether moto. belt is out of 3. lnstall the belt.

4 lf no foresaid phenomena occur, the

electrcnic control mav be brokcn 4 Rcnlecc ihe alpdronl. ..ontr6l

EO2

1. lnspecl whether it exceeds the rated 1. Replace the motor orihe control

and cafl out lhe test aoain

2. lnspecl whether there is lhe over

currenl noise or chared odor at the

ooehtion ofthe motor 2. Replace the motor

3, lnspect Mether there ls a chaffed

odor at the control. 3. ReDlace the control.

4. lnspect whether ihe power voltage

sDecification does not confirm or l@ low. 4 Carry out the test again by using

correct volboe sDecif imtion

E03 Explosion-proof

orotection

1. lnspect whether the power vottage is l. Carry out the test again by using

2. lnspect r

@nnected. r the motor ls @rectly 2. Reconnecl the motor interfa@ to

3. lnspect whethsr there is an abnormal

6d6r in rhc .^ntr61 3, Roplace the @ntrol.

E06 Runnlng @rent of the

motor b l@ lM.

1. lnspect whether lh€ motor lano

1 . Connecl the trEtor line teminals limlu

2 Runnim drent of the mtor is lm lM

E08 24Cr2 ts bfoken d not !.Reda@ d 6Mlv in*d lhe24CO2

E10 lnstant peak current oflhe

molor is abnormal.

'1. hspect whether the toreion of the

drlver is nomal, and the mtor is short

ci@it or strf,-k

X. Elimination methods for common faults: Xl. Precautions for exercise

Warm-up: Before each exercise, it is necessary to take 5-'10 min to do the warming up, including

the warm-up (including the stepping machine, treadmill, rowing machine and exercise bike)

and stretching (stretch the muscles in the training part and bend the joints) to prevent the

sport injury.

Breath: During the exercise, it is not allowed to hold the breath. Generally, inhale from noise

when doing the preparing or homing actions and exhale from mouth when putting forth the

strength. The breath should be coordinating with the actions. ln case of short breath, stop

exercising immediately.

Frequency: The training for the same muscle should be carried out at the interval of 48h, that is

to say, the training for the same muscle should be carried out every other day.

Load: Everyone should determine the training intensity according to his or her physical

conditions. The load exercise should be done progressively. ln the initial exercise, you may

get muscular ache. As only as you keep exercising in the aforesaid frequency, the ache will

be relleved.

Relax: After each exercise, you should do s-minute homing actions, especially the stretchlng and

relaxing for muscles of trained legs to prevent the muscle from getting long{erm spasm

and maintain the elasticity of muscle.

Diet: ln order to protect the digestive system, the exercise can be carried out t hour after the

meal and have meals at least half an hour after the exercise. During the exercise, drink

water as little as possible. lt is forbidden to swallow much water for fear of burdening the

heart and kidney.

-t4-

- l5 -

Robotouch RBT03 User manual

Brand: Robotouch

Model: RBT03

Category: Treadmills

Type: User manual

Download PDF

report

Robotouch RBT03 User manual

Robotouch RBT03 User manual

Other documents