Hoval TopTronic RS-30 User Instruction

User Instructions

For TopTronic® RS-30

430294ENG-Jun02

Hoval Ltd

Northgate

Newark

Nottinghamshire NG24 1JN

Phone 01636 672711

Fax 01636 673532

2 Index 430294ENG-Jun02

Introduction

Introduction ....................................................................................................................................... 3

Controls............................................................................................................................................. 3

Display .............................................................................................................................................. 3

User instructions

Key function table.............................................................................................................................. 4

Switching on the room station ........................................................................................................... 4

Additional information........................................................................................................................ 5

Automatic program selection ............................................................................................................. 5

Room temperature ............................................................................................................................ 6

Heating program ............................................................................................................................... 7

Calorifier charging ............................................................................................................................. 9

Advanced user instructions

Language .......................................................................................................................................... 10

Clock setting...................................................................................................................................... 10

Time clock level................................................................................................................................. 10

Time clock programming ................................................................................................................... 11

Block programming ........................................................................................................................... 14

Table program 1 settings................................................................................................................... 17

Table program 2 settings................................................................................................................... 18

Table program 3 settings................................................................................................................... 19

Room level ........................................................................................................................................ 20

Parameter tables

Room level parameters table............................................................................................................. 23

Advanced parameter table ............................................................................................................... 24

Installation / technical

Installation......................................................................................................................................... 25

Technical data................................................................................................................................... 25

430294ENG-Jun02 Introduction 3

The RS-30 has the most modern technology and serves as a weather / room temperature regulator with

integrated hot water control and remote operating functions for the UltraGas or Topgas boilers.

With the most up to date micro electronics exclusive functions can be activated which guarantee the

highest level of comfort with the minimum energy usage. This is achieved with adaption and optimization

functions which match heating energy to the exact building requirements.

As well as these room temperature related functions a variety of equipment specific information is

available which can be read within the living room and when necessary adapted to individual

circumstances. This encompasses dates, on/off switching of the heating cycle with differently regulated

room temperatures, actual values and diagnostic fault messages of the boiler.

Operation of the unit is easy to understand and is limited to a minimum of operating elements which are

separated for user and advanced user levels. The instructions are separated into two parts.

Part 1 (user instructions) delivers all immediately important operating stages which are necessary for

use and are selected with directly accessible operating keys.

Part 2 (advanced instructions) these should only be used by the advanced user or service engineer

and relate to specific settings / heating parameters and are accessible by the covered operating keys.

Controls

1

4 2

5 3

6

7 10

12 11

13

8 9

1 – LCD Display

2 – Key (increase value)

3 – Key (decrease value)

4 – Key for heating program

5 – Key for reduced (night time) program

6 – Information

7 – Program key (time/date)

8 – Program key (automatic programs)

9 – Program key (house level)

10 – Program key (service level)

11 – Forward key

12 – Backward key

13 – Cover

Symbol Display

Heating Night setback

Room temperature

4 User Instructions 430293ENG-Dec01

Key Function table (User Level)

Function Enter with keys

Adjust with keys /

range Page No.

Room temperature

correction

or

5…30oC

??

Heating (day)

room temperature

or with

or

5…30oC

??

Reduced (night) room

temperature

or with

or

5…30oC

??

Information

??

Party function

press and hold

or

0.5…10h

??

Continuous

heating

press and hold

or

5…30oC

??

Absent function

press and hold

or

0.5…10h

??

Continuous reduced

press and hold

or

5…30oC

??

Heating Off

(manual summer operation)

press and hold

or

On, Off

??

Automatic

or ??

Calorifier

charging

and

simultaneously

ON

or

OFF

??

Automatic programs 1-3

and

simultaneously

or

1, 2, 3

??

Switching on the Room station

When the room station is first switched on the

following display will show for 5 seconds:

Room Station Software version

Control type

The default display will then appear. The

symbol indicates that the room station is in

heating operation and the symbol indicates

the room station is in reduced (night time)

operation.

Information:

Monday 10th March

1997 Time 20.15

Room temperature

20.5oC Clock

synchronisation

i

430294ENG-Jun02 User Instructions 5

Attention:

· During summer switch off the following

symbols are not shown and .

· Blinking symbols or indicate that

the unit is not operating under a normal

program eg. party.

Additional Information

The following additional information can be

obtained by pressing the button (only if the

relevant sensors are fitted):

Default display.

External sensor

temperature.

Flow temperature.

Boiler return

temperature.

Domestic hot water

temperature.

If the calorifier is fitted with a thermostat instead

of a sensor the following will be displayed:

Calorifier on/off.

Default display.

Fault Indications

The RS-30 room station has a comprehensive

fault indication system which has priority over all

other indications and remain active until the fault

is rectified.

Faults concerning the firing unit must be rectified

in accordance with operating manual

instructions.

If any of the following fault displays are shown

(Fault – System Off, Fault – Hot water

temperature, Fault – Boiler temperature, Fault –

Room temperature ) you must notify the heating

engineer.

Automatic Program Selection

In automatic there are three different time

programs to switch between for the heating. As a

general rule these can be used without the need

for adjustment but if individual programs are

required customised cycles can be entered (see

the advanced user section ).

Program 1

Day Heating on time

Mo – Fr

Sa, Su

6.00 - 8.00

16.00 - 22.00

7.00 - 23.00

2 – Program 2

Day Heating on time

Mo – Su 6.00 - 22.00

Program 3

Day Heating on time

Mo – Su 6.00 - 23.00

i

6 User Instructions 430294ENG-Jun02

Changing between Automatic Programs

By using the and keys and following

procedure it is possible to change between the

automatic programs heating.

Press Simultaneously

The following will be displayed for the default

setting of program 2:

Use the and keys to change between

programs 1, 2 or 3.

After 4 secs the default display will be restored.

Room Temperature

By using the program keys and the

increase / decrease value keys the room

temperature can be changed for heating and

reduced (night time).

A – Heating (day room temperature)

If in heating operation as indicated by on the

display follow the procedure below:

press or

Display for heating

operation.

Works setting: 20oC

Adjustment range: 5oC…30oC

press to increase

to decrease

Default screen

automatically returns

after 4 seconds.

If in reduced operation as indicated by on the

display follow the procedure below:

press or

Display for reduced

operation.

press

Display for heating

temperature.

Works setting: 20oC

Adjustment range: 5oC…30oC

press to increase

to decrease

Default screen

automatically returns

after 4 seconds.

B – Reduced (night room temperature)

If in reduced operation as indicated by on the

display follow the procedure below:

press or

Display for reduced

operation.

Works setting: 16oC

Adjustment range: 5oC…30 oC

press to increase

to decrease

Default screen

automatically returns

after 4 seconds.

If in heating operation as indicated by on the

display follow the procedure below:

430294ENG-Jun02 User Instructions 7

press or

Display for heating

operation.

press

Display for reduced

operation.

Works setting: 16oC

Adjustment range: 5oC…30oC

press to increase

to decrease

Default screen

automatically returns

after 4 seconds.

Heating Program

With the two program keys and the

following changes can be made to the programs:

A - Party

B - Heating

C - Absent

D - Reduced

E - Heating off

A – Party

This program is used to switch on or extend the

heating automatic program to a certain time for a

one off event

press and hold

Display for party

program.

For example:

At 20.15 the heating needs to be extended by 3

hours (to 23.15).

press to increase

to decrease

Adjustment range 0.5…10h

It should be noted that the adjustment is from the

time of alteration and not an extension of the

automatic program 1, 2 or 3.

The default display will return after 4 seconds.

To cancel party program

The party program can be cancelled and put

back into automatic by the following procedure:

press and hold

The default display returns after 4 seconds.

B - Heating

This program is used to switch on the heating

continuously.

press and hold

The default display returns after 4 seconds.

8 User Instructions 430294ENG-Jun02

To cancel heating program

The continuous heating program can be

cancelled using the following procedure:

press and hold

The default display will return after 4 seconds.

C – Absent

This program is used to switch to reduced or

extend the reduced automatic program to a

certain time for a one off event

press and hold

Display for absent

program.

For example:

At 13.00 the heating is switched to reduced for

the next 6 hours (to 19.00).

press to increase

to decrease

Adjustment range 0.5…10h

It should be noted that the adjustment is from the

time of alteration and not an extension of the

automatic program 1, 2 or 3.

The default display will return after 4 seconds.

To cancel absent program

The absent program can be cancelled and put

back into automatic by the following procedure:

press and hold

The default display will return after 4 seconds.

D - Reduced

This program is used to switch to reduced

continuously.

press and hold

The default display returns after 4 seconds.

To cancel reduced program

The continuous reduced program can be

cancelled using the following procedure:

press and hold

The default display will return after 4 seconds.

430294ENG-Jun02 User Instructions 9

E – Heating Off

This program enables the heating operation

to be switched off without any danger of

frost. With outside temperature below the set

frost protection limit the heating cycle is

regulated according to the minimum room

temperature. The hot water generation

remains in operation.

Application: Manual summer operation

(heating off, hot water on)

press and hold

The default display will return after 4 seconds.

During this operation method the will blink

To cancel heating off program

The heating off program can be cancelled using

the following procedure:

press and hold

The default display will return after 4 seconds.

Calorifier Charging

With this program it is possible to switch the

calorifier on for a fixed three hour period.

press simultaneously

The default display will return after 4 seconds.

To Cancel program:

press simultaneously

The default display will return after 4 seconds.

10 Advanced User Instructions 430294ENG-Jun02

Language

The room station is programmed in three

languages English, German and French. To

change the language press or key

for 5 seconds. Once the language appears the

keys can be used to change languages.

or

Works setting: ENGLISH

The previous display will return in a few

seconds.

1 - Clock setting

The following functions can be set:

- Time (minutes, hours)

- Day

- Month

- Year

The clock can be set to automatically change

over from summer to winter time by a parameter

in the service level of the central unit.

Changing clock settings

The clock can be changed by using key

and then the and keys to increase or

decrease the values.

- Time

Change with:

to increase

to decrease

Setting Range:

00:00 … 23:59

- Date

Change with:

to increase

to decrease

Setting Range:

1 … 31

- Month

Change with:

to increase

to decrease

Setting Range:

1 … 12

- Year

Change with:

to increase

to decrease

Setting Range:

1995 … 2030

- Return to default display

If the key is not pressed the default display

will return after 2 minutes. It is possible to return

to the default display at any time using the

information key.

2 - Time clock level

In the time clock level the individual program

times can be customized. Standard heating

programs 1, 2 and 3 can be called up as desired

and overwritten with different switch times and

temperatures. Each standard program can thus

be configured individually and stored under the

same program number so that three different

programs are available on demand. These can

then simply be called up in the user operating

level see page 6 for setting of the automatic

program.

Note: Programming of room temperatures is only

possible if the relevant parameter has

been enabled in the service level by an

engineer.

If this has not been done it is only possible

to change the on / off times. In this case

the room temperature will be the works

setting of 20ºC or the corrected value

which has been set in the user level.

The standard programs are lost when

overwritten by customized programs.

These are cancelled after a reset and

replaced by the standard programs and

therefore have to be recreated if needed.

430294ENG-Jun02 Advanced User Instructions 11

Room temperature correction for PARTY and

HEATING with variable temperature

parameter enabled.

For operating types:

- PARTY

- HEATING

The room temperature is set to automatic works

setting of 20ºC or the corrected value which has

been set in the user level.

The actual room temperature values for each of

these two operating types can be set

independently to the automatic program if the

relevant parameter has been enabled in the

service level by an engineer.

The value is set separately when calling up the

operating type PARTY or HEATING by using

the and keys. These values remain

stored for each further call of this operating

type.

Time Clock Programming

It is possible to program up to three cycles /

periods for each desired weekday.

1 – Heating Cycle

For heating each of these cycles has an on / off

as well as a temperature indication for this time

span. The temperature can only be adjusted if

the relevant parameter is enabled in the service

level. Between heating cycles the room

temperature is regulated according to the

night temperature.

2 – Hot Water Cycle

For hot water each of these cycles has an on /

off time. Between hot water cycles hot water

heating is switch off. The temperature is set in

the room level and cannot be changed for each

cycle.

Entering the time clock level

Entering this level is achieved by simply pressing

the key. The program 1, 2 or 3 which is set

in the room level is shown.

Press key

Boiler circuit

Works setting

program 2

or

Boiler circuit

Room level set to

program 1

or

Boiler circuit

Room level set to

program 3

With the and the heating or hot water

circuit can be called up and is available for

programming.

Calling up of heating cycles

With a further pressing of the key the first

heating cycle of the selected program shows

complete with indication of weekday, cycle

number, on time, off time and temperature. Each

value is called up with the key in series

- On time

- Off time

- Temperature

The key can be used to step backwards.

The current value which can be changed with

the and keys is shown blinking. Switch

times can be altered in 5 minute intervals and

temperatures in 0.5K increments in the range of

5-30ºC.

The next heating cycle can be called up by

pressing the key and the process repeated.

Note: The on/off times of not used heating cycles

should be set to 00:00 by simultaneously

pressing the and keys.

The 00:00 value does not refer to a clock

time but only shows an undefined switch

time.

After programming the last heating cycle

(Sunday – cycle 3) the first heating cycle

(Monday – cycle 1) will follow.

12 Advanced User Instructions 430294ENG-Jun02

By pressing the key in quick succession

the programmed cycles can be called up in

series the values noted and corrected if

necessary.

Time clock level can be exited by pressing the

key.

Press to enter

Cycle program

Cycle 1 Monday

ON

Change with

Next setting

OFF

Change with

Next setting

TEMP

(only when set in

service level

parameters)

Change with

Next cycle

Cycle 2 Monday

ON

Change with

Next setting

OFF

Change with

Next setting

TEMP

(only when set in

service level

parameters)

Change with

Next cycle

Cycle 3 Monday

ON

Change with

Next setting

OFF

Change with

Next setting

TEMP

(only when set in

service level

parameters)

Change with

Next cycle

Remaining days in week

Program as Monday

Tuesday ON

cycle 1

Sunday OFF

cycle 3

Automatic Switch off Time Correction

When programming a cycle, if the switch off time

is programmed before the switch on time the

cycle has no function.

Automatic Cycle Sorting

If the heating cycles 1 and 3 are programmed

and the second cycle is not set (indication 00:00)

the second cycle is automatically set to the third

cycle values, the third cycle is then made

available for further programming.

430294ENG-Jun02 Advanced User Instructions 13

Skipping Cycles

If a called up cycle shows 00:00 the next cycle is

skipped.

Heating Cycles which overlap midnight

If a programmed heating time overlaps midnight

e.g. switch on time 6.00pm switch off time

2.00am the cycle must be programmed

separately on both days as shown below.

Day 1 - Swtch on time 6.00pm switch off time

23.55pm and temperature if enabled.

Day 2 - Switch on time 00:00 switch off time

2:00am and temperature if enabled.

Time clock program

The tables shown on pages 17-19 give an

overview of the works programmed standard

programs together with temperature settings

which cannot be lost. When creating customized

programs note the appropriate values in the

tables.

Canceling of individual heating cycles

If necessary individually created cycles can be

cancelled. After selecting the required cycle by

pressing the key several times the cycle

can be cancelled by pressing the and

keys simultaneously.

Enter the

time program

Boiler circuit Hot water circuit

Press several times until

the desired cycle appears

Press Simultaneously

Cycle cancelled

Restore standard program

To restore a customized program to a works

standard program select the program as

described on page 6 and press the and

keys simultaneously.

Enter the

time program

Boiler circuit or Hot water circuit

Press Simultaneously

Standard program

restored

Boiler circuit or Hot water circuit

Standard program Standard program

Restored restored

Time clock level can be exited by pressing the

key. The default display will then be restored.

i

14 Advanced User Instructions 430294ENG-Jun02

Block programming

In order to simplify the programming of the time clocks it is possible to copy the time clock settings in

various ways.

A – Complete automatic programs

It is possible to copy complete heating or hot water programs to other programs for example heating

program 1 to heating program 3. This can be achieved by using the key to enter the time clock and

then the keys to select the heating or hot water as the source. The key is used to select

the target program to which it is to be copied. The key is used to complete the copy. The procedure

is shown in further detail by the illustration below.

Note: It is not possible to copy heating programs to hot water programs or vice versa.

Use or to

change program no.

use to enter program

to be copied to

Copy will

appear

Press key to

confirm copy

OK appears to confirm

program copied

New source program for

further copying

Program will blink

*

* only if present

Source program

Boiler circuit

program 1

Target program

mixer circuit 2

program 2

Program copied

Target program

=

Source program

Copy program 3 from

program 1

Copy hot water prog. 3

from hot water prog. 2

Press to enter clock program

Program will blink

Heating circuit

430294ENG-Jun02 Advanced User Instructions 15

B – Day to day or week

Time programs can also be copied from day to the whole week or from day to day for example Tuesday

to Wednesday.

Day to week

While in the time clock see page 13 the key followed by the key can be used to copy the current

day to the whole week. The procedure is shown in further detail by the illustration on page 16.

Day to day

While in the time clock see page 13 the current day can be copied to another day by using the key

two or more times to select the target day. The key is used to complete the copy of the current day

to the target day. The procedure is shown in further detail by the illustration below.

Enter from heating cycle program

Day copying

Day to copy (source day)

Week Copying

Press

Target day to

Copy to

Press to copy

Source day copied

To target day

Target day =

Source for next copy

Press again to

select target day

Copy again

Day copied to

whole week

Beginning of

week now

displayed

Press to copy

16 Advanced User Instructions 430294ENG-Jun02

Room temperature corrections with individual temperature cycle programs

When individual temperatures have been entered for each heating cycle, the desired room temperature

can be altered via the correction keys or for one of the cycles. This change will then effect all

other heating cycles as shown in the below example:

Original cycle temperatures

New cycle temperatures

As the temperature was increased by 2K during cycle 2 the desired value has been increased by 2K in

the other cycles.

Cycle 2

20ºC + 2K = 22ºC

Cycle 1

18ºC + 2K = 20ºC

Cycle 3

22ºC + 2K = 24ºC Etc.

Cycle 2

20ºC

Cycle 1

18ºC

Cycle 3

22ºC

New Cycle 2

22ºC

Room temp + 2K

430294ENG-Jun02 Advanced User Instructions 17

Program 1 settings

Standard Program 1 - Heating Standard Program 1 - Calorifier

Calorifier temperature - 55oC

Day Setting 1 Setting 2 Setting 3 Day Setting 1 Setting 2 Setting 3

From To Temp From To Temp From To Temp From To From To From To

Mon 6.00 8.00 20oC 16.00 22.00 20oC - - - Mon 6.00 8.00 16.00 22.00 - -

Tue 6.00 8.00 20oC 16.00 22.00 20oC - - - Tue 6.00 8.00 16.00 22.00 - -

Wed 6.00 8.00 20oC 16.00 22.00 20oC - - - Wed 6.00 8.00 16.00 22.00 - -

Thur 6.00 8.00 20oC 16.00 22.00 20oC - - - Thur 6.00 8.00 16.00 22.00 - -

Fri 6.00 8.00 20oC 16.00 22.00 20oC - - - Fri 6.00 8.00 16.00 22.00 - -

Sat 7.00 23.00 20oC - - - - - - Sat 6.00 22.00 - - - -

Sun 7.00 23.00 20oC - - - - - -

Sun 6.00 22.00 - - - -

Custom Program 1 - Heating Custom Program 1 - Calorifier

Calorifier temperature - __oC

Day Setting 1 Setting 2 Setting 3 Day Setting

1

Setting

2

Setting

3

From To Temp From To Temp From To Temp From To From To From To

Mon Mon

Tue Tue

Wed Wed

Thur Thur

Fri Fri

Sat Sat

Sun

18 Advanced User Instructions 430294ENG-Jun02

Program 2 settings

Standard Program 2 - Heating Standard Program 2 - Calorifier

Calorifier temperature - 55oC

Day Setting 1 Setting 2 Setting 3 Day Setting 1 Setting 2 Setting 3

From To Temp From To Temp From To Temp From To From To From To

Mon 6.00 22.00 20oC - - - - - - Mon 6.00 22.00 - - - -

Tue 6.00 22.00 20oC - - - - - - Tue 6.00 22.00 - - - -

Wed 6.00 22.00 20oC - - - - - - Wed 6.00 22.00 - - - -

Thur 6.00 22.00 20oC - - - - - - Thur 6.00 22.00 - - - -

Fri 6.00 22.00 20oC - - - - - - Fri 6.00 22.00 - - - -

Sat 6.00 22.00 20oC - - - - - - Sat 6.00 22.00 - - - -

Sun 6.00 22.00 20oC - - - - - -

Sun 6.00 22.00 - - - -

Custom Program 2 - Heating Custom Program 2 - Calorifier

Calorifier temperature - __oC

Day Setting 1 Setting 2 Setting 3 Day Setting

1

Setting

2

Setting

3

From To Temp From To Temp From To Temp From To From To From To

Mon Mon

Tue Tue

Wed Wed

Thur Thur

Fri Fri

Sat Sat

Sun

430294ENG-Jun02 Advanced User Instructions 19

Program 3 settings

Standard Program 3 - Heating Standard Program 3 - Calorifier

Calorifier temperature - 55oC

Day Setting 1 Setting 2 Setting 3 Day Setting 1 Setting 2 Setting 3

From To Temp From To Temp From To Temp From To From To From To

Mon 6.00 23.00 20oC - - - - - - Mon 00.00 23.55 - - - -

Tue 6.00 23.00 20oC - - - - - - Tue 00.00 23.55 - - - -

Wed 6.00 23.00 20oC - - - - - - Wed 00.00 23.55 - - - -

Thur 6.00 23.00 20oC - - - - - - Thur 00.00 23.55 - - - -

Fri 6.00 23.00 20oC - - - - - - Fri 00.00 23.55 - - - -

Sat 6.00 23.00 20oC - - - - - - Sat 00.00 23.55 - - - -

Sun 6.00 22.00 20oC - - - - - -

Sun 00.00 23.55 - - - -

Custom Program 3 - Heating Custom Program 3 - Calorifier

Calorifier temperature - __oC

Day Setting 1 Setting 2 Setting 3 Day Setting

1

Setting

2

Setting

3

From To Temp From To Temp From To Temp From To From To From To

Mon Mon

Tue Tue

Wed Wed

Thur Thur

Fri Fri

Sat Sat

Sun

20 Advanced User Instructions 430294ENG-Jun02

3 - Room Level

At this level, the parameters relevant to the

heating requirements of the building and its

characteristics can be displayed and changed.

- Hot water temperature

- Hot water operation

- Burner hours run

- Burner starts

- Holiday program

- Clock programs

- Heating curves

- Room temperature correction

- Reset function

Entering the Room Level

Room level can be entered by using the

key. Changes can be made using the ,

and keys.

To exit the room level press the key at any

time.

Press and hold for 3 secs

Hot water

temperature

Works setting: 55ºC

Adjustment range 10ºC … Hot water maximum

temperature

press to increase

to decrease

The maximum temperature is set in the technical

parameter level.

Hot water operation

Works setting: On

Adjustment range: On or Off

Change with keys or

On – Hot water control possible

Off – No Hot water control

Burner hours run

Works setting:

000000.00h

Range: 0 … 99999999

Number of burner

starts

Works setting:

00000000

Range: 0 … 99999999

Holiday program start

Adjust with to increase and to decrease

Change between day and month with and

This function is used to switch the heating to

frost protection only while the building is

unoccupied for example a holiday. The default

display will be today’s date.

Holiday program

finish

Adjust with to increase and to decrease

Change between day and month with and

This function is used to switch the heating back

on when the building becomes occupied.

Example of holiday program

The heating will be

switched to frost

protection only on the

29.3 at 24.00 hrs

The heating will

remain off from 30.3

00.00 hrs to 14.4

00.00 hrs. This will be

the default display until the heating is started

again on 14.4.

i

Page is loading ...

Hoval TopTronic RS-30 User Instruction

Hoval TopTronic RS-30 User Instruction

Related papers

Other documents