HanoverOutdoorFurniture
IMPORTANT
Ifyouhaveanyproblemswiththisproduct(missingordamagedparts,assemblyissues,etc.),
PLEASEDONOTRETURNTOTHERETAILER/STORE
fromwhereyoupurchasedtheproduct.
PleasecallourToll‐FreeCustomerServiceHotlineat:1‐800‐416‐3511
Between9:00AMand5:00PMEasternTime,MondaythroughFriday
Orvisitourwebsiteat:www.hanover‐products.com
Toexpediteanyfuturewarrantyclaims,pleaseretaintheInstructionSheet,Warranty
Cardandreceiptforfutureuse.
For additionalon‐linesupportonassembly,troubleshootingandcare&maintenanceofyouroutdoor
furniture,pleasevisitourwebsiteat:www.hanover‐products.com.
6/1/2015(a)
A
BCS01819
Fig. 1
Fig. 2
B
C
FRONT FOOT CAP
FACTORY ASSEMBLY
8
8
HEX BOLT DRIVER
BOLT COVER
Ø6.5 X 1.0 MM
WASHER
1/4" X 30 MM BOLT
HW0004
8
1
* NOTE: PARTS SHOWN ON PARTS LIST ARE NOT TO SCALE
PARTS LIST QTY
1
1
1
DESCRIPTION ORDER PART #
LEFT ARM
A
B
C
D
E
F
RIGHT ARM
CONNECTOR BAR
1
SEAT FRAME
1
BACK FRAME
Step 1:
IMPORTANT NOTE: Damage to welds or frames resulting from over tightened bolts or improper assembly is not covered
under our warranty.Please read all instructions carefully before assembly. If you have any questions regarding your
assembly,
Remove all protective materials and set parts on a flat, non-abrasive surface. Identify parts packed in carton against the
parts list. If you are missing any parts or are unsure how to proceed with assembly, please call our Product Specialists
immediately at 800 416 3511.
call our Product Specialists at
800 416 3511.
Do not attempt to assemble the chair if any parts are damaged or missing.
call our Product Specialists at .
1---
Insert connector bar into left arm as shown in . Repeat for other side for right arm.
Attach seat frame to base using bolts and washers as shown in . Guide bolt through hole in seat frame, into pre-
drilled hole in the left arm. Hand tighten three to four turns only. . Repeat for opposite side.
Attach back frame to base using bolts and washers as shown in . Guide bolt through hole in back frame, into pre-
drilled hole in the left arm. Hand tighten three to four turns only. . Some adjustments may
be necessary to ensure proper alignment of the table legs. Repeat for opposite side.
Tighten all bolts. Each bolt must be tightened a 3-4 revolutions only at a time. Begin with top left bolts. Move to
bottom right bolts then to top right bolts, followed by bottom left bolts. Repeat this "X" pattern until all bolts are tight.
. Over tightening may strip bolts, damaging the entire chair.
Examine the chair from the front. If the sling seat does not appear tight or straight in the seat base, repeat steps3&4.
If you do not feel your chair is assembled properly, or you have any questions,
1---
Step 2: Fig. 1
Step 3:
Do not tighten completely
Do not tighten completely
Step 4:
DO NOT OVER TIGHTEN BOLTS
Step 5:
1-800-491-4958
Fig.2
Fig.2
PARTS LIST QTY
DESCRIPTION ORDER PART #
G
H
IHW0006
BACK FOOT CAP
FACTORY ASSEMBLY HW0078
FC0307
GFH
GFH
H
F
G
E
D
HW0038
IMPORTANT!! PLEASE READ ENTIRE INSTRUCTION SHEET BEFORE ASSEMBLY!!
TO EXPEDITE ANY FUTURE WARRANTY CLAIMS, PLEASE KEEP INSTRUCTION SHEET, WARRANTY CARD AND RECEIPT
FRONT
FOOT CAP
BACK
FOOT CAP
HW0105
BPS03723
Step 1:
Step 2:
Fig. 1
Fig. 2
.
Identify all parts packed in the carton against the parts list. Remove all protective materials. If you are missing any parts or
are unsure as how to proceed with the assembly,
With the help of another person, place table top upside down on a non-abrasive surface to avoid scratching the top of the rim.
Identify the upper leg and lower leg. Insert the upper leg into lower leg as shown in .
s
sides
IMPORTANT NOTE: Damage to welds or frames resulting from over tightened bolts or improper assembly is not covered
under our warranty. Please read all instructions carefully before assembly. If you have any questions regarding your
assembly,
please call our Product Specialists immediately at 16 3511. Do
not attempt to assemble the chair if any parts are damaged or missing.
call our Product Specialists at 16 3511.
1-800-4 -
Attach table leg to table top using a bolt and washer as shown in . Guide bolt through hole in table leg, into pre-drilled
hole in the table top. Some adjustments may be necessary to ensure proper alignment of the table legs.
Repeat for other three . Your table is now ready for use.
Step 3:
Do not over tighten
1-800-4 -
PARTS LIST QTY
1
1
1
DESCRIPTION ORDER PART #
* NOTE: PARTS SHOWN ON PARTS LIST ARE NOT TO SCALE
FOOT CAP
FACTORY ASSEMBLY
4
4
HEX BOLT DRIVER
UPPER LEG
Ø6.5 X 1.0 MM
WASHER
TABLE TOP
LOWER LEG
1/4" X 42 MM BOLT
Fig. 1 Fig. 2
A
B
C
D
E
F
B
C
E
D
A
HW0004
1
HW0039
HW0006
SZ5450
FOOT CAP
IMPORTANT!! PLEASE READ ENTIRE INSTRUCTION SHEET BEFORE ASSEMBLY!!
TO EXPEDITE WARRANTY CLAIMS PLEASE KEEP INSTRUCTION SHEET, WARRANTY CARD AND COPY OF RECEIPT
-
1
-
2
-
3
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Hanover ORLEANS4PCSW-B-TAN Installation guide
-
Envelor TRADITIONS4PC-BRY Operating instructions
-
-
-
-
-
-
-
Hanover TRADDN7PCSW-B-SU Installation guide
-
