Aiphone WB-CE, WB-CA Install Manual

Category
Security camera accessories
Type
Install Manual
WB-CA, WB-CE
Stainless Steel Wall Mount Box with Assistance
or Emergency Signage and a Light Cage
-INSTRUCTIONS-
Pg. 1 of 2
The WB-CA wall box comes with “ASSISTANCE” in reective blue lettering on both sides of the box. A blue
beacon / strobe light is mounted on top enclosed in a vandal resistant cage.
The WB-CE wall box comes with “EMERGENCY” in reective red lettering on both sides of the box.
A blue beacon / strobe light is mounted on top enclosed in a vandal resistant cage.
The WB-CA and WB-CE are made of 12-Gauge stainless steel and are weather / vandal resistant. The narrow
4" depth of the wall box allows it to meet all ADA mounting requirements. The blue beacon / strobe light
requires a 24V DC power source, not included. Each box includes a UL Listed electrical box for installing an
AC outlet, and a bracket to install a power supply internally. Compatible emergency / assistance sub stations
include the
IX-DVF-2RA*, IX-DVF-RA*, IX-SSA-2RA*, IX-SSA-RA*, IS-DVF-2RA*, IS-SS-2RA-R, and IS-SS-RA-R.
* Stations available with French signage option. Please visit our website for more information (www.aiphone.com/home).
WB-CA
Wall Box with
Caged Light and Blue
Assistance Lettering
WB-CE
Wall Box with
Cage Light and Red
Emergency Lettering
Pg. 2 of 2
WB-CA, WB-CE
0919JD
Aiphone Corporation
www.aiphone.com
(800) 692-0200
MOUNTING / WIRING:
The WB-CA / WB-CE wall box comes pre-assembled with the beacon / strobe light and the cage attached.
Mount the box to the wall, then wire the beacon / strobe light, power, and intercom sub station. Two screws
are provided for mounting the power supply bracket to the internal bracket. Complete the installation by
mounting the intercom sub station to the wall box. See below for additional information.
12"
4-¼"
Back View Front View
Secure the wall box to any at surface
using mounting hardware suitable for
the surface you are mounting to. Top
mounting holes are 4-¼" apart and top
to bottom mounting holes are 12" apart.
There are 3 knockouts on the back and
2 underneath for routing wire.
Connect the red and black wires from the
beacon / strobe light to a 24V DC power source. Red
to positive and black to negative. Connect the white
trigger wire to the N/O side of relay 1 or 2 on the sub
station. Connect the common of relay 1 or 2 to the
positive of the 24V DC power source. See the sub
station’s installation manual for its complete wiring
and dip switch setting options.
Relay 1 connection is shown in example above.
Relay 1 must be enabled during the station
programming process.
SPECIFICATIONS:
Surface box:
Mounting: Surface mount directly to wall
Mounting Height: 48" AFF for camera to be at 60"
44" AFF for call button to be at 48"
Material: 12-Gauge Stainless Steel
Color: Polished Stainless Steel
Dimensions:
Box only 20" H x 10-
9
16
" W x 3-⅞" D
Including cage 26" H x 10-
9
16
" W x 3-⅞" D
Beacon / strobe light:
Voltage: 24V DC
Current: 200mA
Wiring: Black: Ground
Red: +24V DC
White: Trigger
Operating Temp: -40°F to 149°F
+
-
IX-RA (back view)
24V DC
Power Source
Cat-5e / Cat-6
To Network
  • Page 1 1
  • Page 2 2

Aiphone WB-CE, WB-CA Install Manual

Category
Security camera accessories
Type
Install Manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI