TOA BS-680F User manual

TOA
Brand
TOA
Model
BS-680F
Type
User manual

This manual is also suitable for

TOA BS-680FC is a professional Wall Mount Speaker with a rugged metal cabinet, making it ideal for use in areas that require durability and reliability. Suitable for surface or flush mounting, this speaker supports both concealed and exposed wiring, providing flexibility in installation. The speaker's direct wall-mounting structure, with sturdy screws, prevents it from falling easily, even under force. The speaker boasts a 16 cm (6") double cone speaker unit, delivering high-quality sound. It features two steatite screw terminal blocks for easy bridge connection. For added convenience, the push-in type input connector simplifies cable connections and allows bridging.

TOA BS-680FC is a professional Wall Mount Speaker with a rugged metal cabinet, making it ideal for use in areas that require durability and reliability. Suitable for surface or flush mounting, this speaker supports both concealed and exposed wiring, providing flexibility in installation. The speaker's direct wall-mounting structure, with sturdy screws, prevents it from falling easily, even under force. The speaker boasts a 16 cm (6") double cone speaker unit, delivering high-quality sound. It features two steatite screw terminal blocks for easy bridge connection. For added convenience, the push-in type input connector simplifies cable connections and allows bridging.

INSTALLATION MANUAL
WALL MOUNT SPEAKER
Thank you for purchasing TOA’s TOA’s Wall Mount Speaker.
Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.
1. SAFETY PRECAUTIONS
• Beforeinstallationoruse,besuretocarefullyread
all the instructions in this section for correct and
safe operation.
• Besuretofollowalltheprecautionaryinstructions
in this section, which contain important warnings
and/orcautionsregardingsafety.
• After reading, keep this manual handy for future
reference.
• Installtheunitonlyinalocationthatcanstructurally
support the weight of the unit and the mounting
bracket. Doing otherwise may result in the unit
falling down and causing personal injury and/or
propertydamage.
• Donotuseothermethodsthanspeciedtomount
thebracket.Extremeforceisappliedtotheunitand
theunitcouldfalloff,possiblyresultinginpersonal
injuries.
• Tightenallscrewssecurely.Ifanyislooselyxed,
thismaycausethespeakercabinetorbafetofall,
resultinginpersonalinjury.
• Toavoidelectricshocks,besuretoswitchoffthe
amplier'spowerwhenconnectingspeakers.
• Donot operatetheunit for an extended periodof
timewiththesounddistorting.Thisisanindication
of a malfunction, which in turn can cause heat to
generateandresultinare.
• Donotstandorsiton,norhangdownfromtheunit
asthismaycauseittofalldownordrop,resultingin
personalinjuryand/orpropertydamage.
2. FEATURES
• Constructed with metal cabinet, the speakers are
idealforuseinavoiceevacuationsystem.
• Canbesurface-orush-mountedtothewall.
• Either concealed in-wall wiring or exposed wiring
canbeusedforspeakercableconnection.
• Thespeakerstructureofdirectwall-mountingwith
screws prevents the speaker from falling easily
evenifanoutwardforceisappliedto.
• The input impedance can be easily changed by
changing the tap position of the transformer.
• A16cm(6")doubleconespeakerunitensureshigh
qualitysound.
• Two steatite screw terminal blocks (1 cable to 1
connection type) make bridge connection easier.
(BS-680FC)
• The push-in type input connector makes cable
connections easy and allows bridge wiring. (BS-
680F)
• The BS-680FC complies with British Standard
5839part8.
Indicatesapotentiallyhazardoussituationwhich,
if mishandled, could result in death or serious
personalinjury.
WARNING
Indicatesapotentiallyhazardoussituationwhich,
ifmishandled,couldresultinmoderateorminor
personalinjury,and/orpropertydamage.
CAUTION
Traceability Information for Europe
Manufacturer:
TOACorporation
7-2-1,Minatojima-Nakamachi,Chuo-ku,Kobe,Hyogo,Japan
Authorizedrepresentative:
TOAElectronicsEuropeGmbH
Suederstrasse282,20537Hamburg,Germany
CAUTION
WARNING
BS-680F
BS-680FC
3. INSTALLATION
Step 1. Loosen one each of the screws on both
sides of the speaker, then remove the
bafe.
Youcanremovethebafebyloosening
the screw without taking it out.
Step 2. Installthecabinetonthewall.
Thecabinethasknockoutholes(ø20.5mmorø0.81")forcablerouting.
Removethedesiredknockoutholedependingonthewiringmethod,androutecables.
2-1. When installing the cabinet on the wall using the hanging holes:
(1) Fix2suppliedscrews(tappingscrews4x16)
tothewallleavingabout 5mm (0.2")space
from the wall surface.
(2)Removethecabinet'sknockout,thenrunthe
cablesroutedfromthewallthroughthishole.
Inthecaseofexposedwiring,fitthesupplied
rubber grommet into the knockout hole.
Note:Cut a hole in the grommet's thin
membranetomatchthecablesize.
(3) Hook the cabinet onto the stick-out screws,
then tighten the screws.
Tip:The shape ofcabinet's hanging hole is
sodesignedtopreventthecabinetfrom
fallingeasilyevenifanoutwardforceis
appliedto.
2-2. When installing the cabinet on the wall using other holes:
(1) Remove the cabinet's knockout, then run
thecablesroutedfromthewallthroughthis
hole.
Inthecaseofexposedwiring,tthesupplied
rubber grommet into the knockout hole.
Note:Cut a hole in the grommet's thin
membranetomatchthecablesize.
(2)Install the cabinet on the wall using the
mounting holes [a], [b] or [c] shown at right.
Note:Sincenomountingscrewsaresupplied
with the speaker, separately prepare
them appropriate for the construction
ofwallanditsthickness.
2-3. When mounting the cabinet into the wall:
(1) Make a mounting hole of 260 x 175 mm
(10.24"x6.89")inthewall.
(2)Remove the cabinet's knockout hole, run
the cables through this hole, then install
the cabinet using 4 supplied screws
(tappingscrew4x16).
Fit the supplied rubber grommet into the
knockout hole.
Note: Cut a hole in the grommet's thin
membranetomatchthecablesize.
Loosen
Tighten
Baffle
Cabinet
Note: To remove, pull in the arrow
direction after loosening screws.
Cabinet
83.5 mm (3.29")
About 5 mm (0.2")
Hanging hole
Wall
Tapping screw 4 x 16
(accessory)
Knockout hole (ø20.5mm or ø0.81")
Cabinet
Knockout hole: ø20.5 (0.81)
Sides: 4 holes
Bottom: 2 holes
wall
286 (11.26)
260±3
(10.24±0.12)
175±3
(6.89±0.12)
150
(5.91)
Speaker
cable
Tapping screw 4 x 16 (accessory)
Unit: mm (in)
Cabinet
Knockout hole: ø20.5 (0.81)
36 (1.42)
36
(1.42)
60 (2.36)
60 (2.36)
115 (4.53)
4-3.5 x 6.5 (0.14 x 0.26) [a]
2-5.5 x 10
(0.22 x 0.39) [c]
4-ø4.5 (0.18) [b]
Unit: mm (in)
The figure shows BS-680F.
Step 3. Perform wiring.
3-1. Connectboththelead-inandlead-outcablestotheterminalblockattachedtothecabinet.
[Applicable cable]
Step 4. Replacethebafetothecabinet,thentighten2screwslooselyattachedonbothsidesofthecabinet.
3-2. InsertthefastenterminalsttedattheendsoftheHOT,COM,andEarth(BS-680FConly)cablesfrom
the input connector on the cabinet into the taps of the matching transformer on the speaker unit.
Connect the COM cable to the transformer's COMtap,the HOTcabletothedesired transformer's
inputtap,andtheEarthcable(BS-680FConly)tothelugterminalatthetransformerbase.(Referto
thegurebelow.)
Thetablebelowshowstherelationshipbetweenimpedanceandinputpower.
Impedance 1.7kΩ 3.3kΩ 6.7kΩ 13kΩ
100Vline 6W 3W 1.5W 0.8W
70Vline 3W 1.5W 0.8W 0.4W
BS-680F Solidwire:
7-coretwistedwire:
ø0.8–ø1.6mm(AWG20–14)
0.75–1.25mm
2
(AWG18–16)
BS-680FC Solidwire: ø1.0–ø3.0mm(AWG18–9)
3.3kΩ
1.7kΩ
COM
6.7kΩ
13kΩ
3.3kΩ
1.7kΩ
COM
6.7kΩ
13kΩ
Cabinet
Input connector
Input connector
Thermal fuse
From the amplifier
To the next speaker
From the amplifier
Cabinet
Input connector
To the next speaker
From the amplifier
From
the amplifier
To the next speaker
To the next speaker
COM
HOT
5 mm (0.2”)
COM
HOT
[Connection of the BS-680FC]
[Connection of the BS-680F]
COM (white)
HOT (black)
Matching transformer
(on the speaker unit)
Matching transformer
(on the speaker unit)
Input connector
HOT (+)
COM (
-
)
9 mm (0.35”)
URL:http://www.toa.jp/
133-01-00063-02
5. SPECIFICATIONS
Notes
•Thedesignandspecicationsaresubjecttochangewithoutnoticeforimprovement.
•TheSpecicationsdatawasmeasuredinananechoicchamber.
•Referenceaxis: Axisisonthecenterofgrillsurfaceandperpendiculartothegrillsurface.
•Referenceplane: Planeisonthegrillsurfaceandperpendiculartothereferenceaxis.
•Horizontalplane: Planeiscontainingthereferenceaxisandperpendiculartothereferenceplane.
•Othertechnicaldata:SeethespecicationsheetBS-680F/FC.
ModelNo. BS-680F BS-680FC
RatedInput 6W(100Vline),3W(70Vline)
RatedImpedance 100Vline: 1.7kΩ(6W),3.3kΩ(3W),6.7kΩ(1.5W),13kΩ(0.8W)
70Vline: 1.7kΩ(3W),3.3kΩ(1.5W),6.7kΩ(0.8W),13kΩ(0.4W)
Sensitivity 94dBat1W,1m(500Hz–5kHz,pinknoise)
77dBat1W,4m(100Hz–10kHz,pinknoise)accordingtoEN54-24
89dBat1W,1m(100Hz–10kHz,pinknoise)convertedbasedonEN54-24
Maximum
SoundPressureLevel
89.7dBat6W,4m(100Hz–10kHz,pinknoise)accordingtoEN54-24
101.7dBat6W,1m(100Hz–10kHz,pinknoise)convertedbasedonEN54-24
FrequencyResponse 150Hz–20kHz(at20dBbelowpeak)
CoverageAngle(–6dB)
500Hz:180°(HorizontalandVertical);1kHz:140°(HorizontalandVertical);
2kHz:120°(Horizontal),110°(Vertical);4kHz:100°(Horizontal),
80°(Vertical);accordingtoEN54-24
SpeakerComponent 16cm(6")doubleconetype
Standard TraceabilityInformationfor
Europe
(EMCdirective2004/108/EC)
TheEuropeanStandardEN54-24:2008Loudspeakerforvoicealarmsystems
forfiredetectionandfirealarmsystems
Certificationnumber:1438/CPD/0178,Certifiedyear:10
Environmentaltype:A(Indoorapplications)
IncompliancewiththeBritishStandard
BS5839-8:2008
ApplicableCable Solidwire:ø0.8–ø1.6mm
(AWG20–14)
7-coretwistedwire:
0.75–1.25mm
2
(AWG18–16)
Solidwire:ø1.0–ø3.0mm(AWG18–9)
Connection Push-in connector
(Bridgingterminal)
Screw connector
(Steatiteterminalx2)bridging
Finish Baffle,Cabinet:Steelplate,offwhite(RAL9010orequivalentcolor),paint
Grille: Surface-treatedsteelplatenet,offwhite(RAL9010orequivalentcolor),paint
Dimensions 310(w)x190(h)x90(d)mm(12.2"x7.48"x3.54")
Weight 2.6kg(5.73lb)
4. WIRING DIAGRAMS
4.1. BS-680F
8 Ω
13 kΩ
6.7 kΩ
3.3 kΩ
1.7 kΩ
0
COM (white)
COM
HOT (black)
HOT
Matching
transformer
Input
connector
COM
4.2. BS-680FC
8 Ω
13 kΩ
6.7 kΩ
3.3 kΩ
1.7 kΩ
0
Incombustible cablesThermal fuse
(72°C or 161.6°F)
COM
HOT
Earth
COM
HOT
Earth
Matching
transformer
Input
connectors
COM
• Accessories
Rubber grommet ............................................... 2 Tappingscrew(4x16) ......................................4
1438
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

TOA BS-680F User manual

TOA
Brand
TOA
Model
BS-680F
Type
User manual
This manual is also suitable for

TOA BS-680FC is a professional Wall Mount Speaker with a rugged metal cabinet, making it ideal for use in areas that require durability and reliability. Suitable for surface or flush mounting, this speaker supports both concealed and exposed wiring, providing flexibility in installation. The speaker's direct wall-mounting structure, with sturdy screws, prevents it from falling easily, even under force. The speaker boasts a 16 cm (6") double cone speaker unit, delivering high-quality sound. It features two steatite screw terminal blocks for easy bridge connection. For added convenience, the push-in type input connector simplifies cable connections and allows bridging.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents