ADJ 15 HEX BAR IP User manual

User Instructions

15 HEX BAR IP

Europe Energy Saving Notice

Energy Saving Matters (EuP 2009/125/EC)

Saving electric energy is a key to help protecting the enviroment. Please turn o all electrical prod-

ucts when they are not in use. To avoid power consumption in idle mode, disconnect all electrical

equipment from power when not in use. Thank you!

instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying

product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection

claimed includes all forms and matters of copyrightable materials and information now allowed by

statutory or judicial law or hereinafter granted. Product names used in this document may be

trademarks or registered trademarks of their respective companies and are hereby acknowledged.

All non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of

their respective companies.

ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property,

equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic

loss associated with the use or reliance of any information contained within this document, and/or as

a result of the improper, unsafe, unsucient and negligent assembly, installation, rigging, and operation

of this product.

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

FCC RADIO FREQUENCY INTERFERENCE WARNINGS & INSTRUCTIONS

This product has been tested and found to comply with the limits as per Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference in a residential installa

-

tion. This device uses and can radiate radio frequency energy and, if not installed and used in accordance

with the included instructions, may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this device does cause harmful

interference to radio or television reception, which can be determined by turning the device off and on, the

user is encouraged to try to correct the interference by one or more of the following methods:

· Reorient or relocate the device.

· Increase the separation between the device and the receiver.

· Connect the device to an electrical outlet on a circuit different from which the radio receiver is

connected.

· Consult the dealer or an experienced radio/TV technician for help.

DOCUMENT VERSION

Due to additional product features and/or enhancements, an updated version of this document

may be available online.

Please check www.adj.com for the latest revision/update of this manual before beginning

installation and/or programming.

06/10/19

1 1.02

6/9/12/14/17/

30/33/38/41/60

Initial Version

Date

Document

Version

Software

Version >

DMX Channel

Modes

Notes

ADJ Products, LLC - www.adj.com - 15 Hex Bar IP User Manual Page 2

15 Hex Bar IP Table of Contents

Introduction

Features I Warranty Registration I Installation

Safety Precautions

IP65 Notice

Overview I Installation

Manual Tilt Adjustment I Connections

DMX Set Up

DMX Addressing

DMX Modes & Values

Color Macro Chart

System Menu

Master-Slave Set Up

Pixel Zones

Dimmer Curve Chart

Glare Shield Installation I Filter Installation

Dimensional Drawings

Power Linking I Trouble Shooting I Cleaning

Limited Warranty (USA Only)

Specications

3

4

5

7

8

10

11

12

13

17

18

22

23

24

25

26

27

28

29

ADJ Products, LLC - www.adj.com - 15 Hex Bar IP User Manual Page 3

15 Hex Bar IP Introduction

Unpacking: Thank you for purchasing the 15 Hex Bar IP by ADJ Products, LLC. Every unit has been

thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping

carton for damage that may have occurred during shipping. If the carton appears to be damaged,

carefully inspect your xture for any damage and be sure all accessories necessary to operate the unit

has arrived intact. In the case damage has been found or parts are missing, please contact our toll free

customer support number for further instructions. Do not return this unit to your dealer without rst

contacting customer support.

Introduction: The 15 Hex Bar IP is a DMX intelligent, IP rated LED wash fixture. This xture can be

used in a stand alone mode or connected in a Master/Slave conguration.

This product is intended to be used by professionally trained personnel only and is not suitable for

private use.

Customer Support: Contact ADJ Service for any product related service and support needs. Also visit

forums.adj.com with questions, comments or suggestions.

Parts: To purchase parts online visit http://parts.americandj.com

ADJ SERVICE USA - Monday - Friday 8:00am to 4:30pm PST

Voice: 800-322-6337 | Fax: 323-582-2941 | [email protected]

ADJ SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET

Voice: +31 45 546 85 60 | Fax: +31 45 546 85 96 | [email protected]

ADJ PRODUCTS LLC USA

6122 S. Eastern Ave. Los Angeles, CA. 90040

323-582-2650 | Fax 323-532-2941 | www.adj.com | info@adj.com

ADJ SUPPLY Europe B.V

Junostraat 2 6468 EW Kerkrade, The Netherlands

+31 (0)45 546 85 00 | Fax +31 45 546 85 99

www.adj.eu | [email protected]

ADJ PRODUCTS GROUP Mexico

AV Santa Ana 30 Parque Industrial Lerma, Lerma, Mexico 52000

+52 (728) 282-7070

Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself,

doing so will void your manufactures warranty. In the unlikely event your unit may require service

please contact ADJ Products, LLC.

PLEASE recycle the shipping carton when ever possible.

15 Hex Bar IP Features

15 Hex Bar IP Warranty Registration

The 15 Hex Bar IP carries a 2 year limited warranty. Please fill out the enclosed warranty card to

validate your purchase. All returned service items whether under warranty or not, must be freight pre-

paid and accompany a return authorization (R.A.) number. The R.A. number must be clearly written on

the outside of the return package. A brief description of the problem as well as the R.A. number must

also be written down on a piece of paper included in the shipping carton. If the unit is under warranty,

you must provide a copy of your proof of purchase invoice. You may obtain a R.A. number by con-

tacting our customer support team on our customer support number. All packages returned to the

service department not displaying a R.A. number on the outside of the package will be returned to the

shipper.

ADJ Products, LLC - www.adj.com - 15 Hex Bar IP User Manual Page 4

• Multi-Colors

• Five Operating Modes

• Electronic Dimming 0-100%

• DMX-512 protocol

• IP65 Locking 5-Pin XLR Connections In/Out

• 10 DMX Channel Modes: 6 / 9 / 12 / 14 / 17 / 30 / 33 / 38 / 41 / 60

• Multiple Unit Power Linking (See page 27)

Included:

1 x IP65 Locking Power Cable

1 x Removable Frost/Diffuser Filter

1 x Removable Glare Shield

2 x Omega Brackets

ADJ Products, LLC - www.adj.com - 15 Hex Bar IP User Manual Page 5

15 Hex Bar IP Safety Precautions

• Do not attempt to operate this unit if the power cord has been frayed or broken. Do not attempt to

remove or break o the ground prong from the electrical cord. This prong is used to reduce the risk

of electrical shock and re in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Never plug this unit in to a dimmer pack

• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6”

(15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to be walked on or pinched by

items placed upon or against them, paying particular attention to the point they exit from the unit.

• Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 27

for cleaning details.

• Heat -The appliance should be situated away from heat sources such as radiators, heat registers,

stoves, or other appliances (including amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the fixture.

C. The fixture does not appear to operate normally or exhibits a marked change in performance.

D. The fixture has fallen and/or subjected to extreme handling.

15 Hex Bar IP Safety Precautions

RISK GROUP 3 - RISK OF EXPOSURE TO ULTRAVIOLET (UV) RADIATION!

FIXTURE EMITS HIGH INTENSITY ULTRAVIOLET (UV) LIGHT FROM THE UV LED.

WEAR PROPER EYE AND SKIN PROTECTION.

AVOID PROLONGED PERIODS OF EXPOSURE TO THE UV LED.

AVOID WEARING WHITE COLOR CLOTHING AND/OR USING (UV) PAINTS ON SKIN.

AVOID DIRECT EYE AND/OR SKIN EXPOSURE AT DISTANCES SHORTER THAN 11 feet (3.3m).

DO NOT OPERATE FIXTURE WITH DAMAGED OR MISSING EXTERNAL COVER.

DO NOT LOOK DIRECTLY INTO THE (UV) LIGHT AND/OR VIEW (UV) LIGHT DIRECTLY WITH

OPTICAL INSTRUMENTS THAT MAY CONCENTRATE THE LIGHT/RADIATION OUTPUT.

INDIVIDUALS SUFFERING FROM A RANGE OF EYE CONDITIONS, SUNLIGHT EXPOSURE

DISORDERS, OR INDIVIDUALS USING PHOTOSENSITIVE MEDICATION, MAY RECEIVE

DISCOMFORT IF EXPOSED TO THE ULTRAVIOLET (UV) LIGHT EMITTED FROM THIS FIXTURE.

ADJ Products, LLC - www.adj.com - 15 Hex Bar IP User Manual Page 6

ADJ Products, LLC - www.adj.com - 15 Hex Bar IP User Manual Page 7

15 Hex Bar IP IP65 Notice

IP65 RATED

An IP rated lighting xture is one, which is commonly installed in outdoor environments

and has been designed with an enclosure that eectively protects the ingress (entry)

of external foreign objects such as dust and water. The International Protection (IP)

rating system is commonly expressed as "IP" (Ingress Protection) followed by two

numbers (i.e. IP65) where the numbers dene the degree of protection. The rst digit

(Foreign Bodies Protection) indicates the extent of protection against particles entering

the xture and the second digit (Water Protection) indicates the extent of protection

against water entering the xture. An IP65 rated lighting xture is one, which has been

designed and tested to protect against the ingress of dust (6) and low-pressure water

jets from any direction (5).

MARINE/COASTAL ENVIRONMENT INSTALLATIONS

NOT suitable for marine and/or coastal environment installations. Installing

this xture in a marine and/or coastal environment may cause corrosion and/

or excessive wear to the interior and/or exterior components of the xture.

Damages and/or performance issues resulting from installation in a marine

and/or coastal environment will void the manufactures warranty and will NOT be subJect

to any warranty claims and/or repairs.

ADJ Products, LLC - www.adj.com - 15 Hex Bar IP User Manual Page 8

15 Hex Bar IP Installation

Always ensure that the unit is rmly xed to avoid vibration and slipping while operating. Always

ensure that the structure to which you are attaching the unit is secure and is able to support a weight

of 10 times the unit’s weight. ALWAYS use safety cables that can hold 12 times the weight of the

unit when installing the xture.

This equipment must be installed by a professional, and it must be installed in a place where it is out

of the reach of people’s grasp. Overhead mounting requires extensive experience, including calculat-

ing working load limits, installation material being used, and perodic safety inspection of all installa-

tion material and unit. If you lack these qualications, do not attempt the installation yourself. These

installaiton should be checked by a skilled person once a year.

Ensure ALL connections and end caps are properly sealed with a non-conductive dielectric

grease (available at most electrical suppliers) to prevent water ingress/condensation and/or

corrosion.

The 15 Hex Bar IP is fully operational in three dierent mounting positions; hanging upside-down,

mounted sideways on trussing, or set on a at level surface. Be sure this xture is kept at least 12m

(40ft) away from any ammable materials (decoration etc.). ALWAYS use and install the supplied

safety cable as a safety measure to prevent accidental damage and/or injury in the event the clamp

fails.

Screw one clamp via a M12 screw and nut into the Omega holder. Insert the quick-lock fasteners of

the Omega holder into the respective holes of the adjustable mounting bracket. Tighten the quick-

lock fasteners fully clockwise. Pull the safety-cable through the attachment openings and over the

trussing system or a safe xation spot. Insert the end in the carabine and tighten the safety screw.

PLEASE SEE THE NEXT PAGE FOR CLAMP AND SAFETY CABLE INSTALL.

15 Hex Bar IP Overview

LCD Screen

Mode Button

Up Button

Down Button

Enter Button

IP65 5-Pin XLR Connection In

IP65 5-Pin XLR Connection Out

IP65 Locking Power

Connection In

IP65 Locking Power

Connection Out

ADJ Products, LLC - www.adj.com - 15 Hex Bar IP User Manual Page 9

15 Hex Bar IP Installation

1. Attach a clamp (not included)

to each omega bracket.

2. Attach the omega brackets

to the bracket mounts located on

the 15 Hex Bar IP brackets.

3. Turn the quick-lock

fastners fully clockwise to lock

the Omega brackets into place.

4. Attach safety cables (not included)

to both safety cable attachment points.

NOTE: Safety cable attachment points are located

at both ends. Its recommended to use safety

cables on both ends.

ALWAYS ATTACH A SAFETY CABLE WHENEVER

INSTALLING THIS DEVICE IN A SUSPENEDED

ENVIRONMENT TO ENSURE THE FIXTURE WILL

NOT DROP IF THE CLAMP FAILS.

ADJ Products, LLC - www.adj.com - 15 Hex Bar IP User Manual Page 10

15 Hex Bar IP Connections

ENSURE ALL CONNECTIONS AND END CAPS ARE PROPERLY SEALED WITH A DIELECTRIC

GREASE (AVAILABLE AT MOST ELECTRICAL SUPPLIERS) TO PREVENT WATER CORROSION

AND/OR ELECTRICAL SHORT CIRCUIT.

TO MAINTAIN IP65 RATING INTEGRITY AND PREVENT WATER FROM ENTERING THE FIXTURE,

ALL UNUSED CONNECTION RUBBER CAPS MUST BE SEALED.

15 Hex Bar IP Manual Tilt Adjustment

The bar angle is adjustable manually using the brackets located on each side

of the unit. Simply loosen the tilt adjustment knobs attached to each mounting

bracket and adjust the bracket accordingly. After making your desired set up,

securely tighten the tilt adjustment knobs. See picture below for a 90 degree set

up.

90 Degree Setting

ADJ Products, LLC - www.adj.com - 15 Hex Bar IP User Manual Page 11

15 Hex Bar IP DMX Set Up

DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used as a form of communication

between intelligent fixtures and controllers. A DMX controller sends DMX data instructions from

the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the

DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have a

DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of dierent manufactures to be

linked together and operate from a single controller, as long as all xtures and the controller are DMX

compliant. To ensure proper DMX data transmission, when using several DMX fixtures try to use

the shortest cable path possible. The order in which fixtures are connected in a DMX line does not

influence the DMX addressing. For example; a fixture assigned a DMX address of 1 may be placed

anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a fixture is

assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that

unit, no matter where it is located in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX Operation): The 15 Hex Bar IP can be controlled

via DMX-512 protocol. The 15 Hex Bar IP has 10 DMX channel modes. The DMX address is set on the

back panel of the 15 Hex Bar IP. Your unit and your DMX controller require a standard 5-pin XLR connec-

tor for data input and data output. We recommend Accu-Cable DMX cables. If you are making your own

cables, be sure to use standard 110-120 Ohm shielded cable (This cable may be purchased at almost all

pro lighting stores). Your cables should be made with a male and female XLR connector on either end

of the cable. Also remember that DMX cable must be daisy chained and cannot be split.

Special Note: Line Termination.

When longer runs of cable are used, you may need to use a terminator

on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is connected

between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is inserted in the female

XLR connector of the last unit in your daisy chain to terminate the line. Using a cable terminator (ADJ

part number Z-DMX/T) will decrease the possibilities of erratic behavior.

ADJ Products, LLC - www.adj.com - 15 Hex Bar IP User Manual Page 12

All xtures should be given a DMX starting address when using a DMX controller, so the correct xture

responds to the correct control signal. This digital starting address is the channel number from which

the xture starts to “listen” to the digital control signal sent out from the DMX controller. The assignment

of this starting DMX address is achieved by setting the correct DMX address on the digital control

display on the xture.

You can set the same starting address for all xtures or a group of xtures, or set dierent addresses

for each individual xture. Setting all xtures to the same DMX address will cause all xtures to react

in the same way, in other words, changing the settings of one channel will aect all the xtures

simultaneously.

If you set each xture to a dierent DMX address, each unit will start to “listen” to the channel number

you have set, based on the quantity of DMX channels of each xture. That means changing the settings

of one channel will only aect the selected xture.

In the case of the 15 Hex Bar IP, when in 6 channel mode you should set the starting DMX address of

the rst unit to 1, the second unit to 7 (6 + 1), the third unit to 13 (7 + 6), and so on. (See chart below

for more details.)

15 Hex Bar IP DMX Addressing

Channel Mode

Unit1

Address

Unit2

Address

Unit3

Address

Unit4

Address

6 Channels 1 7 13 19

9 Channels 1 10 19 28

12 Channels 1 13 25 37

14 Channels 1

15 29

43

17 Channels 1

18 35

52

33 Channels 1

34 67

100

30 Channels 1

31 61

91

41 Channels 1

42 83

124

38 Channels 1

39 77

115

60 Channels 1

61 121

181

ADJ Products, LLC - www.adj.com - 15 Hex Bar IP User Manual Page 13

15 Hex Bar IP DMX Modes & Values

VALUES FUNCTIONS

RED FINE (ZONE #1)

GREEN FINE (ZONE #1)

BLUE FINE (ZONE #1)

WHITE FINE (ZONE #1)

AMBER FINE (ZONE #1)

UV FINE (ZONE #1)

RED FINE (ZONE #2)

GREEN FINE (ZONE #2)

BLUE FINE (ZONE #2)

1

2

3

4

5

6

6 Ch 9 Ch 12 Ch 14 Ch 17 Ch 33 Ch

000-255

RED (ALL LEDS)

0-100%

000-255

GREEN (ALL LEDS)

0-100%

000-255

BLUE (ALL LEDS)

0-100%

000-255

WHITE (ALL LEDS)

0-100%

000-255

AMBER (ALL LEDS)

0-100%

000-255

UV (ALL LEDS)

0-100%

000-255

RED (ZONE #1)

0-100%

000-255

GREEN (ZONE #1)

0-100%

000-255

BLUE (ZONE #1)

0-100%

000-255

WHITE (ZONE #1)

0-100%

000-255

AMBER (ZONE #1)

0-100%

000-255

UV (ZONE #1)

0-100%

000-255

RED (ZONE #2)

0-100%

000-255

GREEN (ZONE #2)

0-100%

000-255

BLUE (ZONE #2)

0-100%

30 Ch

38 Ch 60 Ch41 Ch

RED FINE (ALL LEDS)000-255

GREEN FINE (ALL LEDS)000-255

BLUE FINE (ALL LEDS)000-255

WHITE FINE (ALL LEDS)000-255

AMBER FINE (ALL LEDS)000-255

UV FINE (ALL LEDS)000-255

000-255

1

2

3

4

5

6

1

2

3

4

5

6

1

2

3

4

5

6

1

3

5

7

9

11

2

4

6

8

10

12

1

2

3

4

5

6

1

2

3

4

5

6

1

2

3

4

5

6

1

2

3

4

5

6

7

8

9

7

8

9

7

8

9

7

8

9

1

3

5

7

9

11

13

15

17

2

4

6

8

10

12

14

16

18

ADJ Products, LLC - www.adj.com - 15 Hex Bar IP User Manual Page 14

15 Hex Bar IP DMX Modes & Values

VALUES FUNCTIONS

WHITE FINE (ZONE #3)

AMBER FINE (ZONE #3)

UV FINE (ZONE #3)

RED FINE (ZONE #4)

GREEN FINE (ZONE #4)

BLUE FINE (ZONE #4)

WHITE FINE (ZONE #4)

AMBER FINE (ZONE #4)

UV FINE (ZONE #4)

6 Ch 9 Ch 12 Ch 14 Ch 17 Ch 33 Ch

000-255

WHITE (ZONE #2)

0-100%

000-255

AMBER (ZONE #2)

0-100%

000-255

UV (ZONE #2)

0-100%

000-255

RED (ZONE #3)

0-100%

000-255

GREEN (ZONE #3)

0-100%

000-255

BLUE (ZONE #3)

0-100%

000-255

WHITE (ZONE #3)

0-100%

000-255

AMBER (ZONE #3)

0-100%

000-255

UV (ZONE #3)

0-100%

000-255

RED (ZONE #4)

0-100%

000-255

GREEN (ZONE #4)

0-100%

000-255

BLUE (ZONE #4)

0-100%

000-255

WHITE (ZONE #4)

0-100%

000-255

AMBER (ZONE #4)

0-100%

000-255

UV (ZONE #4)

0-100%

30 Ch

38 Ch 60 Ch41 Ch

WHITE FINE (ZONE #2)000-255

AMBER FINE (ZONE #2)000-255

UV FINE (ZONE #2)000-255

RED FINE (ZONE #3)000-255

GREEN FINE (ZONE #3)000-255

BLUE FINE (ZONE #3)000-255

000-255

31

33

35

37

39

41

43

45

47

32

34

36

38

40

42

44

46

48

19

20

21

22

23

24

25

26

27

28

29

30

16

17

18

19

20

21

22

23

24

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

10

11

12

13

14

15

ADJ Products, LLC - www.adj.com - 15 Hex Bar IP User Manual Page 15

15 Hex Bar IP DMX Modes & Values

VALUES FUNCTIONS6 Ch 9 Ch 12 Ch 14 Ch 17 Ch 33 Ch

000-255

RED (ZONE #5)

0-100%

000-255

GREEN (ZONE #5)

0-100%

000-255

BLUE (ZONE #5)

0-100%

000-255

WHITE (ZONE #5)

0-100%

000-255

AMBER (ZONE #5)

0-100%

000-255

UV (ZONE #5)

0-100%

30 Ch

38 Ch 60 Ch41 Ch

RED FINE (ZONE #5)000-255

GREEN FINE (ZONE #5)000-255

BLUE FINE (ZONE #5)000-255

WHITE FINE (ZONE #5)000-255

AMBER FINE (ZONE #5)000-255

UV FINE (ZONE #5)000-255

000-031

032-063

064-095

096-127

128-159

160-191

192-223

224-255

49

50

51

52

53

54

55

56

57

58

59

60

25

26

27

28

29

30

25

26

27

28

29

30

25

26

27

28

29

30

25

26

27

28

29

30

COLOR MACROS

See Color Macro Chart on page 16

000-255

COLOR TEMPERATURES

2700-7000K

000-255

SHUTTER & STROBE

LEDs Off

LEDs On

Strobing Slow - Fast

LEDs On

Pulse Strobing in Sequences

LEDs On

Random Strobing Slow - Fast

LEDs On

MASTER DIMMER

0% - 100%

000-255

DIMMER FINE

0% - 100%

000-255

7 7 3131

8 8 3232

9 9 3333317

10 10 3434328

11 11 3535339

000-010

011-026

027-043

044-060

061-076

077-093

094-110

111-126

127-143

144-160

161-176

177-193

194-210

211-226

227-255

AUTO PROGRAMS

Off

Auto Program 1

Auto Program 2

Auto Program 3

Auto Program 4

Auto Program 5

Auto Program 6

Auto Program 7

Auto Program 8

Auto Program 9

Auto Program 10

Auto Program 11

Auto Program 12

Auto Program 13

No Function

12 36

ADJ Products, LLC - www.adj.com - 15 Hex Bar IP User Manual Page 16

15 Hex Bar IP DMX Modes & Values

VALUES FUNCTIONS6 Ch 9 Ch 12 Ch 14 Ch 17 Ch 33 Ch30 Ch

38 Ch 60 Ch41 Ch

000-255

AUTO PROGRAM SPEED

Slow - Fast

000-255

AUTO PROGRAM FADE

Slow - Fast

13 37

14 38

DIMMER MODES

Standard

Stage

TV

Architectural

Theatre

Stage 2

DIMMER DELAY TIME

0.1Sec.

0.2Sec.

0.3Sec.

0.4Sec.

0.5Sec.

0.6Sec.

0.7Sec.

0.8Sec.

0.9Sec.

1.0Sec.

1.5Sec.

2.0Sec.

3.0Sec.

4.0Sec.

5.0Sec.

6.0Sec.

7.0Sec.

8.0Sec.

9.0Sec.

10Sec.

Default to Unit Setting

000-020

021-040

041-060

061-080

081-100

101-120

121

122

123

124

125

126

127

128

129

130

131

132

133

134

135

136

137

138

139

140

141-255

REFRESH RATES

Default to Unit Setting

900Hz

1000Hz

1100Hz

1200Hz

1300Hz

1400Hz

1500Hz

2500Hz

4000Hz

5000Hz

10000Hz

15000Hz

20000Hz

25000Hz

No Function

000-015

016-030

031-045

046-060

061-075

076-090

091-105

106-120

121-135

136-150

151-165

166-180

181-195

196-210

211-225

226-255

GAMMA

Default to Unit Setting

2.0

2.2

2.4

2.6

2.8

No Function

000-020

021-040

041-060

061-080

081-100

101-120

121-255

15 3912 36

16 4013 37

17 4114 38

ADJ Products, LLC - www.adj.com - 15 Hex Bar IP User Manual Page 17

15 Hex Bar IP Color Macro Chart

0-3=Off 64-67=B+W 128-131=G+B+W 192-195=R+B+W+A

4-7=Red 68-71=B+A 132-135=G+B+A 196-199=R+B+W+UV

8-11=Green 72-75=B+UV 136-139=G+B+UV 200-203=R+B+A+UV

12-15=Blue 76-79=W+A 140-143=G+W+A 204-207=R+W+A+UV

16-19=White 80-83=W+UV 144-147=G+W+UV 208-211=G+B+W+A

20-23=Amber 84-87=A+UV 148-151=G+A+UV 212-215=G+B+W+UV

24-27=UV 88-91=R+G+B 152-155=B+W+A 216-219=G+B+A+UV

28-31=R+G 92-95=R+G+W 156-159=B+W+UV 220-223=G+W+A+UV

32-35=R+B 96-99=R+G+A 160-163=B+A+UV 224-227=B+W+A+UV

36-39=R+W 100-103=R+G+UV 164-167=W+A+UV 228-231=R+G+B+W+A

40-43=R+A 104-107=R+B+W 168-171=R+G+B+W 232-235=R+G+B+W+UV

44-47=R+UV 108-111=R+B+A 172-175=R+G+B+A 236-239=R+G+B+A+UV

48-51

=G+B 112-115=R+B+UV 176-179=R+G+B+UV 240-243=R+G+W+A+UV

52-55=G+W 116-119=R+W+A 180-183=R+G+W+A 244-247=R+B+W+A=UV

56-59=G+A 120-123=R+W+UV 184-187=R+G+W+UV 248-251=G+B+W+A+UV

60-63=G+UV 124-127=R+A+UV 188-191=R+G+A+UV 252-255=R+G+B+W+A+UV

ADJ Products, LLC - www.adj.com - 15 Hex Bar IP User Manual Page 18

15 Hex Bar IP System Menu

SYSTEM MENU

The xture includes an easy to navigate system menu control panel display where all necessary

settings and adjustments are made. (See image below) During normal operation, pressing the MENU

button once will access the xture’s main menu. Once in the main menu, you can navigate through

the dierent functions and access the sub-menus with the UP and DOWN buttons. When you reach

a eld that requires adjusting, press the ENTER button to access that eld and use the UP and

DOWN buttons to adjust the eld. Pressing the ENTER button once more will conrm your setting.

You may exit the main menu at any time without making any adjustments by pressing the MENU

button.

ADJ Products, LLC - www.adj.com - 15 Hex Bar IP User Manual Page 19

15 Hex Bar IP System Menu

DMX SET

001-512

DMX Lost Status

DMX Channel Mode

Selection

DMX Addressing

6CH / 9CH / 12CH / 14 CH / 17CH / 30CH /

33CH / 38CH / 41CH / 60CH

MENU OPTIONS DESCRIPTIONSUBMENU

Slave Setting

Address

Ch. Mode

No DMX Hold / Blackout / Int. Prog

Persnlty

(Personality)

Manual

On / Off

Manual Control Settings

Master Setting

Dim Mode

Dimming Curve Modes

Dimming Speed

Standard / Stage / TV / Archi (Architectural) /

Theatre / Stage 2

DimSpeed: 0.1-0.9s ~ 1-10s

LEDRfrsh

(LED Refresh Rate)

900 / 1000 / 1100 / 1200 / 1300 / 1400 / 1500 /

2500 / 4000 / 5000 / 10000 / 15000 / 20000 /

25000 (Hz)

LED Refresh Setting

Gamma

2.0 / 2.2 / 2.4 / 2.6 / 2.8 Gamma Brightness

Display

SaveDlay: 1~10M Display Shutoff Time

Service

Restore: YES / NO

(Pass Code = 011)

Calibration Adjustment

Restore Factory Settings

Red

Green

Blue

White

Amber

UV

Strobe

MastrDim

ClrMacro

ClrTemp

Lock: OFF / 1M~10M Display Control Lock

Pass Code = 50

Calibrat (Calibration)

(Pass Code = 050)

000-255

000-063

000-255

Master

Slave

IntProgs

(Internal Programs)

Prog 1

Prog 2

Prog 3

Prog 4

Prog 5

Program 6

Program 7

Program 8

Program 9

Program 10

Program 11

Program 12

Program 13

Program 1 with Adjustments

Program 2 with Adjustments

Program 3 with Adjustments

Program 4 with Adjustments

Program 5 with Adjustments

Program 6 with Adjustments

Program 7 with Adjustments

Program 8 with Adjustments

Program 9 with Adjustments

Program 10 with Adjustments

Program 11 with Adjustments

Program 12 with Adjustments

Program 13 with Adjustments

Speed: 000-255 Fade: 000-255

Page is loading ...

ADJ 15 HEX BAR IP User manual

ADJ 15 HEX BAR IP User manual

Related papers

Other documents