Wohler AMP1-2SDA+ – 2 Channel Audio Monitoring Owner's manual

Brand: Wohler

Model: AMP1-2SDA+ – 2 Channel Audio Monitoring

Category: Musical Equipment

Type: Owner's manual

This manual is also suitable for

AMP1-2SDA

1RU, 2-Channel, 3G/HD/SD-SDI / AES / Analog

Audio Monitor

User Guide

Software Release: V1.xx

Part Number 821817, Revision E

Page 2

This publication is protected by federal copyright law. No part of this publication may be copied or

distributed, stored in a retrieval system, or translated into any human or computer language in any

form or by any means electronic, mechanical, manual, magnetic, or otherwise, or disclosed to third

parties without the express written permission of Wohler Technologies, Inc.

Reproduction

Licensed users and authorized distributors of Wohler Technologies, Inc. products may copy this

document for use with Wohler Technologies., Inc. products provided that the copyright notice above

is included in all reproductions.

Customer Support

Wohler Technologies, Inc.

1280 San Luis Obispo Ave.

Hayward, CA 94544 www.wohler.com

Phone: 510-870-0810

FAX: 510-870-0811

US Toll Free: 1-888-596-4537 (1-888-5-WOHLER)

Web: www.wohler.com Sales: sales@wohler.com

Support: support@wohler.com

Disclaimers

Even though Wohler Technologies, Inc. has tested its equipment and software, and reviewed the

documentation, Wohler Technologies, Inc. makes no warranty or representation, either express or

implied, with respect to software, documentation, their quality, performance, merchantability, or

fitness for a particular purpose.

In no event will Wohler Technologies, Inc. be liable for direct, indirect, special, incidental, or

consequential damages resulting from any defect in the hardware, software, or its documentation,

even if advised of the possibility of such damages.

Some states do not allow the exclusion or limitation for incidental or consequential damages, so the

above exclusion or limitation may not apply to you.

Printing

This document looks best when printed on a color printer since some images may be indistinct when

printed on a black and white printer.

PDF

All text strings appearing in this shade of blue are hyperlinks.

Other Technologies and Products

Google Chrome is a registered trademark of Alphabet Inc. Microsoft Windows and Internet Explorer

are registered trademarks of Microsoft Corporation.

Last Update

February 21, 2020

Page 3

TABLE OF CONTENTS

Contents

User Guide..........................................................................................1

TABLE OF CONTENTS............................................................................3

Contents .........................................................................................................3

CHAPTER 1: Quick Start ........................................................................5

Introduction ....................................................................................................5

Overview...............................................................................................5

Safety.............................................................................................................5

Instructions ...........................................................................................5

Safety Symbols......................................................................................6

Mounting...............................................................................................6

Heat Dissipation.....................................................................................7

Sympathetic Vibration.............................................................................7

Mechanical Bracing.................................................................................7

Connections and Cable Recommendations .................................................8

Electrical Interference.............................................................................8

Power ...................................................................................................8

Compliance .....................................................................................................9

FCC ......................................................................................................9

ICES-003 ..............................................................................................9

Front Panel....................................................................................................10

Rear Panel.....................................................................................................11

CHAPTER 2: Operation ........................................................................ 15

Introduction ..................................................................................................15

Main Screen ..................................................................................................15

CHAPTER 3: Option Settings ................................................................ 17

CHAPTER 3: Option Settings ................................................................ 18

Introduction ..................................................................................................18

Option Menu Overview....................................................................................18

Option Settings..............................................................................................19

CHAPTER 4: Features & Specifications................................................... 21

Introduction ..................................................................................................21

Features .......................................................................................................21

Compliance ...................................................................................................22

Specifications ................................................................................................22

SDI Audio Formats .........................................................................................23

Technical Functional Overview .........................................................................24

Page 4

APPENDIX A: Firmware Updates ........................................................... 25

Introduction ..................................................................................................25

Upgrading the Firmware Using a USB Flash Drive ...............................................26

Possible Firmware Update Problems..................................................................27

APPENDIX B: Option Card Installation ................................................... 28

Page 5

CHAPTER 1: Quick Start

Introduction

Overview

The AMP1-2SDA is a 1RU, 2-channel, 3G/HD/SD-SDI, AES, and Analog audio

monitor. This unit comes with a powerful audio amplifier to overcome ambient

noise. It also has two 26-segment level meters for audio level metering. You can

visually and audibly monitor any selected audio pair. There is also a 4-digit, 14-

segment display for setup and status display. The AMP1-2SDA is small, low-cost,

reliable and simple to operate.

Note that very little configuration should be necessary. We have already configured

the unit to the most commonly requested settings. However, should you need to

change these settings, you can quickly and easily access the optional settings using

the front panel controls and the Status Display.

Safety

Instructions

1. Read, keep, and follow all of these instructions; heed all warnings.

2. Do not use this equipment near water.

3. Use only a dry cloth to clean the equipment.

4. Do not block any ventilation openings.

5. Do not install near any heat source such as a radiator, heat register, amplifier, or

stove.

6. Do not attempt to plug the unit into a two-blade outlet (with only two prongs of

equal width).

Important:

By design, this monitor will only plug into a three

prong outlet for your safety.

If the plug does not fit into the outlet, contact an electrician to replace the

obsolete outlet.

Page 6

7. Protect the power cord from being walked on or pinched, particularly at plug

connections on the equipment and at the socket.

8. Use only the attachments/accessories specified by the manufacturer.

9. Unplug the equipment during lightning storms or when unused for long periods

of time.

10. Refer all servicing to qualified service personnel. Servicing will be required

under all of the following conditions:

a. The equipment has been damaged in any way, such as when the power-

supply cord or plug is damaged.

b. Liquid had been spilled or objects have fallen onto the equipment.

c. The equipment has been exposed to rain or moisture.

d. The equipment does not operate normally.

e. The equipment has been dropped.

Safety Symbols

Mounting

The unit is designed for a standard 19" rack. Install it at ear/eye level for best high

frequency response and visual observation of the display screens. Please adhere to

the following clearances:

Table 1-1: Clearance Recommendations

Clearance

Surface

24”

Front

3”

Rear

2”

Sides

1.75”

Top and Bottom (if either radiates heat)

0”

Top and Bottom (if no heat)

WARNING:

The symbol to the left warns of electric shock hazard inside the unit.

Disconnect the power cord before removing access panels when installing

upgrades. Only qualified service personnel are to operate the equipment

with covers removed, and are to exercise caution to avoid personal injury.

Page 7

Heat Dissipation

The ambient temperature inside the mounting enclosure should not exceed 40°

Celsius (104° Fahrenheit). Adjacent devices can be rack mounted (or stacked) in

proximity to the unit if this temperature is not exceeded. Otherwise, allow a 1RU

(1.75”/44.45mm) space above and below the unit for air circulation.

Sympathetic Vibration

Sympathetic vibration from other equipment (cables, etc.,) in the rack may be

serious enough to interfere with the sound quality of the unit. If you experience

sympathetic vibrations, use thin card stock, felt, foam, or weather-stripping

between the vibrating surfaces. Tie loose cables securely with cable ties.

Mechanical Bracing

The 1RU chassis is securely attached to the front panel. In addition, the chassis has

mounting tabs through which you attach it to the rack rail. This feature will reduce

or eliminate rear bracing requirements in many mobile/portable applications. The

weight of internal components is distributed fairly evenly around the unit.

Important:

To reduce noise, the monitor does not have any fans. As a result,

the heat

generated by the class D power amplifiers, power supplies, and other

components is vented by slots in the sides and back of the unit. Therefore, as

a safety precaution, you must allow proper ventilation on these surfaces.

Page 8

Connections and Cable Recommendations

We recommend that you limit the length of the cables that you use for feeding

3G/HD/SD-SDI signals sources to the SDI connector and that you use a Belden

1694A cable (or equivalent).

Table 1-2: SDI Cable Length Limit Recommendations

Maximum Length

Signal Type

Meters Feet

300

984

150

492

246

Electrical Interference

Be careful to avoid mismatched cable types and other similar causes of undesired

reflections in digital signal systems. If severe enough, such reflections can result in

corruption of the digital data stream. As with any audio equipment, maximum

immunity from electrical interference requires the use of shielded cable; however,

satisfactory results can sometimes be obtained without it. The internal circuitry

ground is connected to the chassis.

Power

The unit comes with a standard internal power supply and connects an A/C mains

power source (60W, 100 to 240 VAC, ±10%, 50/60Hz) through the IEC connector

provided on the rear panel of the unit.

When the mains plug or appliance coupler is used as the disconnect device, the

disconnect device should remain operable.

Note

The connections of all DB

connectors are compatible with

Tascam DB

25 to XLR cable assemblies. Consult the factory for availability. All rear-

panel connectors are female except the XLR output connectors.

Page 9

Compliance

FCC

This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful

interference, in which case the user will be required to correct the interference at

their own expense.

ICES-003

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du

Canada.

Page 10

Front Panel

This section provides a description of each control or indicator on the front panel.

Figure 1–1: Front Panel Layout

1. Volume: The Volume knob controls the volume of the internal speakers,

headphones, and optionally of the rear panel balanced analog outputs.

2. Status Screen: Typically the Status Screen displays the selected audio source

and channel pair. In Figure 1-1, the selected source is the 3G/HD/SD-SDI input

and the selected channel pair if pair 2, for example. The Status Screen is also

used to assist in setting up options.

3. Phase Indicator: This LED provides a green indication if the two channels are

in phase, on average. It provides a red indication if the two channels are out of

phase, on average.

4. Balance: The Balance knob adjusts the left/right balance between the

speakers, headphones, and optionally between the rear panel balanced analog

outputs.

5. Headphone Jack: A 1/4" stereo jack for optional headphones is provided on

the front panel.

6. USB 2.0 Port: This USB Type A connector allows you to use a flash drive (not

supplied) to update the unit’s firmware. Refer to Appendix A.

7. Source Selector: This knob allows you to select the input source: analog, AES,

or SDI. To set up the various options in the AMP1-2SDA, press this knob for at

least 3 seconds. Chapter 3 describes reviewing and changing options.

8. Pair Selector: This knob allows you to select the specific channel pair to be

monitored from multi-channel sources. It also has secondary functions when

configuring options. Chapter 3 describes reviewing and changing options.

9. Level Meters: Two 26-segment meters provide left and right channel metering.

These high-resolution LED bar graph displays feature a dynamic range of 66 dB

with PPM dot over VU bar ballistic characteristics.

10.Power Indicator: This green LED indicates that the AMP1-2SDA is receiving AC

power.

11.Speakers: Audio monitoring is achieved through the use of Class D amplifiers

driving two (left/right) wide range speakers.

Page 11

Rear Panel

This section provides a description of each connector on the rear panel, as well as

diagrams for each XLR or DB25 connector.

Figure 1–2: Rear Panel Layout

1. Power Connection: The AMP1-2SDA uses a standard IEC power cord for the

100 to 240 VAC ±10%, 50/60 Hz power connection.

2. Balanced Analog Inputs: These two XLR-F connectors accept left and right

balanced analog line level input signals. Connect to either the Balanced Analog

Inputs or the Unbalanced Analog inputs. If you connect to both, they will mix,

but this is not considered normal operation. Refer to Figure 1-3 for the wiring

connections of each connector.

Figure 1-3: Balanced Analog Input XLR-F Pin Out

Pin 2

High (+)

Pin 1

Gnd

(Shield)

Pin 3

Low (-)

Page 12

3. Optional Additional 8 Balanced Analog Inputs: Each of these two DB-25-F

connectors accept four left and right balanced analog line level input signals.

Refer to Figure 1-4 for the wiring connection of each connector.

Figure 1-4: Balanced Analog Input XLR-F Pin Out

4. Optional Additional 8 Balanced AES Inputs: This DB-25-F connector accepts

eight balanced AES input Channel pairs. Refer to Figure 1-5 for the wiring

connections of this connector.

Figure 1-5: Balanced AES Input XLR-F Pin Out

5. Unbalanced Analog Inputs: These two RCA connectors accept left and right

unbalanced analog component audio level input signals. Use either the Balanced

Analog Inputs or the Unbalanced Analog Inputs. If you use both, they will mix,

but this is not considered normal operation.

Note

The connections of all DB

connectors are compatible with

Tascam DB

to XLR cable assemblies. Consult the factory for availability. All rear-panel

DB-25 connectors are female.

Page 13

6. Gain & AES Termination Switches: These switches perform the following

functions:

a. Operate / Calibrate (Switch 1) is set to Operate (up) by default. This

switch is not implemented and is reserved for possible future use.

b. Analog to Digital Reference Level (Switches 2 & 3) allow you to adjust

the analog level that will correspond to a metered value. The default

setting is +4 dBu analog = -20 dBFS digital (Switch 2 up, 3 down). A +4

dBu analog input level will display as a -20 dBFS reading on the bar graph

meters and also transition from green to amber at that segment. Refer to

the silk-screened chart on the rear panel or to Table 1-3.

Table 1-3: Analog to Digital Reference Level

Switch

Reference Level

2 3 Analog (dBu) Digital (dBFS)

Down

c. AES Termination (Switch 4) allows you to set or remove the termination

on the unbalanced 75Ω AES input. The default is OFF (down). Set the

termination to ON (up) only if this is the last in a series of AES

connections.

7. Unbalanced AES Input: This BNC connector accepts an unbalanced 75Ω AES

input signal to be monitored. If this is the last AES connection in a series, set

the Termination Switch to ON (up). Refer to Item 6c of this chapter. There

should never be two terminations in an AES cable connection.

8. Unbalanced AES Output: This BNC connector produces a 75Ω unbalanced AES

output signal consisting of the audio channel pair selected from any of the

inputs.

9. 3G/HD/SD-SDI Input: This BNC connector accepts a 3G/HD/SD-SDI input

signal to be monitored. Refer to Table 1-2 for considerations regarding cable

length for this input.

10.3G/HD/SD-SDI Output: This BNC connector regenerates the 3G/HD/SD-SDI

input signal.

Page 14

11.Balanced Analog Outputs: These XLR-M connectors provide left and right

balanced analog signals consisting of the selected, metered audio channel pair

from any of the inputs. There are also several options that will affect the signal

level of the Balanced Analog Output. Refer to the Option Settings section of

Chapter 3 for explanations of these options. Refer to Figure 1-6 for the wiring

connections of each connector.

Figure 1-6: Balanced Analog Output XLR-M Pin Out

Page 15

CHAPTER 2: Operation

Introduction

This chapter describes how to operate the AMP1-2SDA. It is a good idea to

connect any or all of the inputs you will be monitoring before proceeding in

this chapter.

Main Screen

When the AMP1-2SDA is powered, it will first test the Status Display by lighting all

of the segments, as shown in Figure 2-1, for one second:

Fig 2–1: Display Test

Then it will display part of the product name, as shown in Figure 2-2, for one

second:

Fig 2–2: Product Name

Following this, it will display the version number of its software in the format shown

in Figure 2-3 for two seconds:

Fig 2–3: Software Version

Page 16

Finally, it will display the input selection, which is the last selected input type and

pair before the power was removed from the unit. The Status Display will appear

as shown in Figure 2-4 below.

Fig 2–4: Status Display

Turn the Source knob to select a different source. The Status Display will change

immediately as you turn the knob. Turning the Pair knob will select a pair within

that source if there is more than one. Table 2-1 shows the possible Source and

Pair selections. Note that if an optional AES or Analog source is not installed, then

it will not be presented as a possible choice as you rotate the Source knob.

Table 2-1: Source and Channel Pair Displays

Input Display

Channel Pair Range

3G/HD/SD-SDI BNC SDI. 1

through

AES Unbalanced BNC AES. B

only

Analog Balanced XLR x 2 or

Analog Unbalanced RCA x 2

ANA. A only

AES Balanced DB25 (Optional) AES. 1

through

Analog Balanced DB25 x 2 (Optional)

ANA. 1

through

After selecting a Source and a Pair, adjust the Volume and Balance controls to

suitable levels. The Level Meters will display the level of the selected channel pair

of the selected input source. If the Phase Avg indicator is green, this indicates that

the two channels of the selected channel pair are, on average, in phase. If the

Phase Avg indicator is red, this indicates that the two channels of the selected

channel pair are, on average, out of phase.

The selected Source/Pair will also be output from the Headphone Jack, from the

Note

Throughout the remainder of this manual, characters in the

Status Display

will

be shown in text in the following format:

SDI.1

Page 17

Analog Output connectors, and from the AES Output connector. The signals in the

Analog Output connectors can optionally be controlled by the Volume and Balance

controls. Refer to Chapter 3.

If the pair selected from a digital source is unlocked or if the source is not

connected, the display will alternate between and Source/Pair selection and

UNLK. If the pair selected from a digital source contains an encoded signal that is

not PCM, the Source/Pair selection will alternate with CMPR. Either of these

indications mean that the audio on the selected pair cannot be monitored audibly or

shown on the level meters.

Note

Anytime the AMP1

2SDA power is cycled, the last source and pair selecte

d will

be recalled from non-volatile memory. The selection is saved 15 seconds after

the last change is made. The periods in the display will flash to indicate this.

If power is removed from the unit before this occurs, the previously saved

source will be recalled.

Page 18

CHAPTER 3: Option Settings

Introduction

This chapter explains the uses for the various option settings provided in the

product, as well as how to adjust them.

Option Menu Overview

You can launch the Option Menu system by pressing and holding the

Source

control for at least three seconds. After the first setting (Analog Out) appears,

rotating the Source control will move from setting to setting. Table 3-1 lists the

option settings in the order in which they will be encountered.

Table 3–1: Option Settings

Option Setting Display

Possible

Settings

Description

TRIM

The Analog Output will be affected by

the Analog Out Trim setting.

FIX

The Analog Output will be fixed at the

same level as the input signal.

V/B

The Analog Output will be affected by

the Volume and Balance controls.

Analog Out

AOUT

MUTE

The Analog Output will be muted.

Analog Out Trim

ATRM

-60

+12

Adjusts from -60 dB to +12 dB in 1 dB

steps, affecting the Analog Output

signals.

NORM

Best for most situations.

LOUD

Use when louder output is needed.

Speaker Adjust

SPKR

MUTE

The internal speakers will be muted.

Treble Adjust

TREB

-12

+12

Adjusts from -12 dB to +12 dB in 1 dB

steps affecting the sound from the

speakers and optional headphones.

Bass Adjust

BASS

-12

+12

Adjusts from -12 dB to +12 dB in 1 dB

steps affecting the sound from the

speakers and optional headphones.

Display Brightness

BRGT HIGH or LOW

Two possible settings affecting the

Status Display, the Level Meters, and

the Phase AVG

indicator.

Factory Reset

FRST NO or YES

Resets all options to factory defaults.

Page 19

Option Settings

The various option settings are discussed in detail in this section. After holding the

Source control for at least 3 seconds and entering the Option Menu system,

rotating the Source control will allow you to review the settings. Each setting is

displayed by alternating the name of the setting with the value of the setting. For

example a Display Brightness setting of High would be shown as:

BRGT HIGH BRGT HIGH

To change a setting, first turn the Source control to the option you want to adjust.

Then turn the Pair control to the setting you want for that option. To accept the

new setting, just turn the Source control to the next option you want to adjust, if

any.

When you are finished making all of the adjustments you want, press either the

Source or Pair control for at least 3 seconds to exit the Option Settings section.

Alternatively, you may just do nothing and wait. The Option Settings section will

automatically exit after 10 seconds of no activity.

1. Analog Out: When AOUT appears, it will alternate with its setting.

Turning the Pair control will change through the possible settings:

a. TRIM sets the Analog Output level to the value you set in the Analog

Out Trim setting.

b. FIX is the default setting. No gain adjustments will be made to the

Analog Output levels.

c. V/B causes the Analog Output level to be controlled by the Volume and

Balance controls. This setting can be useful if the Analog Output

connections will be used to drive external amplifiers and speakers for

listening. The analog outputs are muted when headphones are inserted.

d. MUTE The Analog Outputs will mute regardless of any other setting.

2. Analog Out Trim: The ATRM setting will only appear if the Analog Out

option is set to TRIM. When the ATRM option appears, turning the Pair

control will adjust or trim the level of the Analog Output connections to the

desired level. A full range of adjustment from -60 dB to +12 dB is available.

The default setting is 0 dB. It is helpful to be listening to the Analog Output

through the external piece of equipment that you have connected it to when

making this adjustment.

Page 20

3. Speaker Loudness: The SPKR setting affects the sound out of the

speakers. The NORM option is the factory default and is suitable for most

applications. The LOUD option is designed to be used when the selected

audio source is quiet, or when the ambient noise of the room is loud. The

LOUD option trades a flat frequency response for more gain where you need

it most, and compresses the dynamic range of the audio source. This setting

in combination with the TREB and BASS settings allows you to tailor the

speaker response to your needs. The MUTE option is designed to be used if

external speakers are connected to the Analog Outputs.

4. Treble: The TREB adjustment affects the sound of the internal speakers

and the Headphone Jack. 0 dB is the default setting. Adjust it anywhere

between -12 dB and +12 dB, according to your preference. Lowering Treble

compensates for high frequency pre-emphasis or removes sibilant effects.

Increasing Treble will add “sizzle” to the sound and bring high-pitched

sounds out of the mix.

5. Bass: The BASS adjustment affects the sound of the internal speakers

and the Headphone Jack. 0 dB is the default setting. Adjust it anywhere

between -12 dB and +12 dB, according to your preference. Lowering Bass

will unmask midrange band sounds, while increasing Bass will make the

sound “fatter”.

6. Display Brightness: The BRGT adjustment has two settings. The default

setting is HIGH. It adjusts the brightness of the Status Display, the

Level Meters, and the Phase AVG indicator. Adjust the setting for easy

readability according to the ambient lighting conditions.

7. Factory Reset: When set to YES, the FRST menu item will set all

options to their factory defaults when you exit the menu system. The menu

item automatically returns to NO when the menu system is entered again.

Note

New settings are automatically written to non

volatile memory fifteen seconds

after the last change is made. All of the periods in the display are flashed to

indicate this. Do not remove power from the unit until this happens, or your

changes will not return when power is reapplied to the unit

Page is loading ...

Wohler AMP1-2SDA+ – 2 Channel Audio Monitoring Owner's manual

Brand: Wohler

Model: AMP1-2SDA+ – 2 Channel Audio Monitoring

Category: Musical Equipment

Type: Owner's manual

This manual is also suitable for

Download PDF

report

Wohler AMP1-2SDA+ – 2 Channel Audio Monitoring Owner's manual

This manual is also suitable for

Wohler AMP1-2SDA+ – 2 Channel Audio Monitoring Owner's manual

Related papers

Other documents