Greenheck 483966 Wall Bracket Operating instructions

Greenheck
Brand
Greenheck
Model
483966 Wall Bracket
Type
Operating instructions

Greenheck 483966 Wall Bracket

The Greenheck 483966 Wall Bracket is designed for use with Greenheck Centrifugal Upblast Exhaust Fans in sizes 060-300. It provides a secure and stable mounting platform for the fan, allowing for proper airflow and operation.

Key Features:

  • Pre-punched 5/16 inch holes for easy mounting
  • Compatible with various anchoring methods, including concrete, timber, and steel
  • Durable construction with stainless steel bolts and black phosphate coated steel nuts
  • Accommodates fan sizes up to 300
  • Ensures a watertight seal around the fan perimeter

Installation:

Greenheck 483966 Wall Bracket

The Greenheck 483966 Wall Bracket is designed for use with Greenheck Centrifugal Upblast Exhaust Fans in sizes 060-300. It provides a secure and stable mounting platform for the fan, allowing for proper airflow and operation.

Key Features:

  • Pre-punched 5/16 inch holes for easy mounting
  • Compatible with various anchoring methods, including concrete, timber, and steel
  • Durable construction with stainless steel bolts and black phosphate coated steel nuts
  • Accommodates fan sizes up to 300
  • Ensures a watertight seal around the fan perimeter

Installation:

Wall Bracket 1
Document 483966
Wall Bracket
Centrifugal Upblast Exhaust, Sizes 060-300
Installation, Operation and Maintenance Manual
Please read and save these instructions for future reference. Read carefully before attempting to assemble, install,
operate or maintain the product described. Protect yourself and others by observing all safety information. Failure
to comply with these instructions will result in voiding of the product warranty and may result in personal injury
and/or property damage.
Hardware List
Item
Number
Qty. Fan Size Description
Part
Number
1
8 060-200
1/4 - 20 x 0.75” L Hex Bolt,
Stainless Steel
415573
14 220-300
2
8 060-200
1/4 - 20 U Style Spring Nut,
Black Phosphate Coated Steel
415244
14 220-300
Recommendations for Installation
Wall brackets have pre-punched 5/16 inch holes for mounting the bracket to the wall. Hole diameter may need to be
increased depending on the anchor fasteners chosen by the installer. Quantity of fan-to-wall bracket fasteners vary
by wall bracket size. Refer to ‘Included Hardware’ table above.
Concrete Anchoring
A. Concrete - 4 inch minimum wall
thickness. Minimum of 2,500 psi.
B. Expansion Wedge Anchors
- Min. of 3/8inch diameter
- Min. of 2inch engagement
- Use a washer under each nut
Timber Anchoring
C. Wood Timber - minimum nominal
thickness of 4 inch.
D. Lag Bolt
- Min. of 5/16 inch diameter
- Min. 2 inch of thread engagement
- Use a washer under each bolt head
Steel Anchoring
E. Structural Steel
- 1/8 inch thick or 12 ga min.
F. Self-Drilling Screw
- Min. size of #12
- Min. 1/2 inch of thread hangout
- Use a washer under each screw
head.
A
B
Item #2
Item #1
C
D
F
E
483966 • Wall Bracket, Rev. 3, February 20212
Wall Opening Size
Unit Size
Fan Curb Cap Size
(in.)
Maximum Wall Opening - X
(in.)
060-070 17 12.5
080-130 19 14.5
099-160 22 17.5
140-160 26 21.5
180-200 30 25.5
220-240 34 29.5
300 40 35.5
X
1. Cut an appropriate sized hole in the wall based on
the ‘Wall Opening Size’ table above.
2. Locate the wall bracket in the desired installation
position and check for potential unit clearance
issues.
3. Using the anchoring guidelines on page 1, fasten
the wall bracket to the wall. If mounting a size 240
or 300, ensure the sides of the wall bracket with the
four U-nuts are on the top and bottom.
4. Caulk the perimeter of the wall bracket to ensure a
watertight seal. See Figure 1. Shims or additional
sealant methods may be needed for an uneven wall
surface.
5. If the installation requires a backdraft damper, it
should be installed in the duct at this time.
6. Lift the fan into place and orient the breather tube
and drain/grease trough in a downward position as
shown in Figure 2.
7. Secure fan to the wall bracket using the supplied
1/4 - 20 hex bolts. You may need to use a drift,
small screwdriver, or the supplied bolts to properly
position the U-nuts.
8. Complete fan installation using the instruction
manual provided with the fan.
Caulk entire perimeter
of wall bracket
Figure 1
Figure 2
Breather
Tube
Hoodband
Drain/Grease
Trough
NOTE
Do NOT support the unit by the hoodband during
installation.
Installation
  • Page 1 1
  • Page 2 2

Greenheck 483966 Wall Bracket Operating instructions

Greenheck
Brand
Greenheck
Model
483966 Wall Bracket
Type
Operating instructions

Greenheck 483966 Wall Bracket

The Greenheck 483966 Wall Bracket is designed for use with Greenheck Centrifugal Upblast Exhaust Fans in sizes 060-300. It provides a secure and stable mounting platform for the fan, allowing for proper airflow and operation.

Key Features:

  • Pre-punched 5/16 inch holes for easy mounting
  • Compatible with various anchoring methods, including concrete, timber, and steel
  • Durable construction with stainless steel bolts and black phosphate coated steel nuts
  • Accommodates fan sizes up to 300
  • Ensures a watertight seal around the fan perimeter

Installation:

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents