Dell Latitude E7240 Ultrabook Owner's manual

Category
Notebooks
Type
Owner's manual
Dell Latitude E7240
Owner's Manual
Regulatory Model: P22S
Regulatory Type: P22S001
April 2021
Rev. A05
Notes, cautions, and warnings
NOTE: A NOTE indicates important information that helps you make better use of your computer.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid
the problem.
WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
Copyright © 2015 Dell Inc. All rights reserved. This product is protected by U.S. and international copyright and intellectual property laws.
Dell
and the Dell logo are trademarks of Dell Inc. in the United States and/or other jurisdictions. All other marks and names mentioned herein
may be trademarks of their respective companies.
Chapter 1: Working on Your Computer...........................................................................................5
Before Working Inside Your Computer...........................................................................................................................5
Turning Off Your Computer.............................................................................................................................................. 6
After Working Inside Your Computer..............................................................................................................................6
Chapter 2: Docking Your Computer............................................................................................... 8
Chapter 3: Removing and Installing Components...........................................................................9
Recommended Tools.........................................................................................................................................................10
System Overview............................................................................................................................................................... 10
Removing the SD Card...................................................................................................................................................... 11
Installing the SD Card........................................................................................................................................................ 11
Removing the Battery........................................................................................................................................................11
Installing the Battery......................................................................................................................................................... 12
Removing the Base Cover............................................................................................................................................... 13
Installing the Base Cover..................................................................................................................................................14
Removing the mSATA SSD card.................................................................................................................................... 14
Installing the mSATA SSD card...................................................................................................................................... 14
Removing the Keyboard Trim..........................................................................................................................................14
Installing the Keyboard Trim............................................................................................................................................15
Removing the Keyboard................................................................................................................................................... 15
Installing the Keyboard..................................................................................................................................................... 16
Removing the Palmrest.................................................................................................................................................... 16
Installing the Palmrest.......................................................................................................................................................17
Removing the WiFi Switch Board.................................................................................................................................17
Installing the WiFi Switch Board...................................................................................................................................18
Removing the Memory Module.......................................................................................................................................18
Installing the Memory Module.........................................................................................................................................18
Removing the WLAN Card...............................................................................................................................................18
Installing the WLAN Card.................................................................................................................................................19
Removing the WWAN Card............................................................................................................................................. 19
Installing the WWAN Card............................................................................................................................................... 19
Removing the Display Bezel........................................................................................................................................... 20
Installing the Display Bezel..............................................................................................................................................20
Removing the Display Panel........................................................................................................................................... 20
Installing the Display Panel.............................................................................................................................................. 21
Removing the Coin-Cell Battery.....................................................................................................................................21
Installing the Coin-Cell Battery...................................................................................................................................... 22
Removing the Speakers................................................................................................................................................... 22
Installing the Speakers..................................................................................................................................................... 22
Removing the Display-Hinge Cover.............................................................................................................................. 23
Installing the Display-Hinge Cover................................................................................................................................ 23
Removing the Heatsink.................................................................................................................................................... 23
Installing the Heatsink...................................................................................................................................................... 24
Contents
Contents 3
Removing the Display Assembly.................................................................................................................................... 24
Installing the Display Assembly...................................................................................................................................... 25
Removing the System Fan.............................................................................................................................................. 26
Installing the System Fan................................................................................................................................................ 26
Removing the System Board..........................................................................................................................................26
Installing the System Board............................................................................................................................................ 27
Removing the Power Connector .................................................................................................................................. 28
Installing the Power Connector..................................................................................................................................... 28
Chapter 4: Docking Port Information........................................................................................... 29
Chapter 5: System Setup............................................................................................................ 30
Boot Sequence...................................................................................................................................................................30
Navigation Keys................................................................................................................................................................. 30
System Setup Options...................................................................................................................................................... 31
Updating the BIOS ........................................................................................................................................................... 37
System and Setup Password..........................................................................................................................................38
Assigning a System Password and Setup Password.......................................................................................... 38
Deleting or Changing an Existing System and/or Setup Password................................................................ 39
Chapter 6: Diagnostics................................................................................................................ 40
Enhanced Pre-Boot System Assessment (ePSA) Diagnostics.............................................................................. 40
Device Status Lights........................................................................................................................................................ 40
Battery Status Lights........................................................................................................................................................41
Chapter 7: Specifications............................................................................................................ 42
Chapter 8: Contacting Dell.......................................................................................................... 46
4
Contents
Working on Your Computer
Topics:
Before Working Inside Your Computer
Turning Off Your Computer
After Working Inside Your Computer
Before Working Inside Your Computer
Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your personal
safety. Unless otherwise noted, each procedure included in this document assumes that the following conditions exist:
You have read the safety information that shipped with your computer.
A component can be replaced or--if purchased separately--installed by performing the removal procedure in reverse order.
NOTE: Disconnect all power sources before opening the computer cover or panels. After you finish working inside the
computer, replace all covers, panels, and screws before connecting to the power source.
NOTE: Before working inside your computer, read the safety information that shipped with your computer. For additional
safety best practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance
CAUTION: Many repairs may only be done by a certified service technician. You should only perform
troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or
telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by
your warranty. Read and follow the safety instructions that came with the product.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically
touching an unpainted metal surface, such as a connector on the back of the computer.
CAUTION: Handle components and cards with care. Do not touch the components or contacts on a card. Hold a
card by its edges or by its metal mounting bracket. Hold a component such as a processor by its edges, not by
its pins.
CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable itself. Some
cables have connectors with locking tabs; if you are disconnecting this type of cable, press in on the locking
tabs before you disconnect the cable. As you pull connectors apart, keep them evenly aligned to avoid bending
any connector pins. Also, before you connect a cable, ensure that both connectors are correctly oriented and
aligned.
NOTE: The color of your computer and certain components may appear differently than shown in this document.
To avoid damaging your computer, perform the following steps before you begin working inside the computer.
1. Ensure that your work surface is flat and clean to prevent the computer cover from being scratched.
2. Turn off your computer (see Turning off Your Computer).
3. If the computer is connected to a docking device (docked), undock it.
CAUTION:
To disconnect a network cable, first unplug the cable from your computer and then unplug the
cable from the network device.
4. Disconnect all network cables from the computer.
5. Disconnect your computer and all attached devices from their electrical outlets.
6. Close the display and turn the computer upside-down on a flat work surface.
1
Working on Your Computer 5
NOTE: To avoid damaging the system board, you must remove the main battery before you service the computer.
7. Remove the main battery.
8. Turn the computer top-side up.
9. Open the display.
10. Press the power button to ground the system board.
CAUTION: To guard against electrical shock, always unplug your computer from the electrical outlet before
opening the display.
CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal
surface, such as the metal at the back of the computer. While you work, periodically touch an unpainted
metal surface to dissipate static electricity, which could harm internal components.
11. Remove any installed ExpressCards or Smart Cards from the appropriate slots.
Turning Off Your Computer
CAUTION: To avoid losing data, save and close all open files and exit all open programs before you turn off your
computer.
1. Shut down the operating system:
In Windows 8:
Using a touch-enabled device:
a. Swipe in from the right edge of the screen, opening the Charms menu and select Settings.
b. Select the and then select Shut down
Using a mouse:
a. Point to upper-right corner of the screen and click Settings.
b. Click the
and select Shut down.
In Windows 7:
a. Click Start .
b. Click Shut Down.
or
a. Click Start .
b. Click the arrow in the lower-right corner of the Start menu as shown below, and then click Shut
Down..
2. Ensure that the computer and all attached devices are turned off. If your computer and attached devices did not
automatically turn off when you shut down your operating system, press and hold the power button for about 4 seconds to
turn them off.
After Working Inside Your Computer
After you complete any replacement procedure, ensure you connect any external devices, cards, and cables before turning on
your computer.
CAUTION:
To avoid damage to the computer, use only the battery designed for this particular Dell computer. Do
not use batteries designed for other Dell computers.
1. Connect any external devices, such as a port replicator or media base, and replace any cards, such as an ExpressCard.
2. Connect any telephone or network cables to your computer.
6
Working on Your Computer
CAUTION: To connect a network cable, first plug the cable into the network device and then plug it into the
computer.
3. Replace the battery.
4. Connect your computer and all attached devices to their electrical outlets.
5. Turn on your computer.
Working on Your Computer 7
Docking Your Computer
Follow the steps to dock your computer:
a. Place the docking spacer until the docking spacer clicks on its place in the docking station.
b. Place the computer on the docking spacer to dock your
computer.
NOTE:
This docking spacer can be used to dock only the Latitude E7240 / Latitude E7440 computers. You cannot dock any
other Dell computers using this docking station.
2
8 Docking Your Computer
Removing and Installing Components
This section provides detailed information on how to remove or install the components from your computer.
Topics:
Recommended Tools
System Overview
Removing the SD Card
Installing the SD Card
Removing the Battery
Installing the Battery
Removing the Base Cover
Installing the Base Cover
Removing the mSATA SSD card
Installing the mSATA SSD card
Removing the Keyboard Trim
Installing the Keyboard Trim
Removing the Keyboard
Installing the Keyboard
Removing the Palmrest
Installing the Palmrest
Removing the WiFi Switch Board
Installing the WiFi Switch Board
Removing the Memory Module
Installing the Memory Module
Removing the WLAN Card
Installing the WLAN Card
Removing the WWAN Card
Installing the WWAN Card
Removing the Display Bezel
Installing the Display Bezel
Removing the Display Panel
Installing the Display Panel
Removing the Coin-Cell Battery
Installing the Coin-Cell Battery
Removing the Speakers
Installing the Speakers
Removing the Display-Hinge Cover
Installing the Display-Hinge Cover
Removing the Heatsink
Installing the Heatsink
Removing the Display Assembly
Installing the Display Assembly
Removing the System Fan
Installing the System Fan
Removing the System Board
Installing the System Board
Removing the Power Connector
Installing the Power Connector
3
Removing and Installing Components 9
Recommended Tools
The procedures in this document may require the following tools:
Small flat-blade screwdriver
Phillips screwdriver
Small plastic scribe
System Overview
Figure 1. Inside View Back
1. system fan
2. mSATA card
3. battery bay
4. SD card
5. WLAN card
6. WWAN card
7. memory module
8. heatsink
Figure 2. Inside view Front
10
Removing and Installing Components
1. coin-cell battery 2. SIM card board
3. speaker 4. system board
5. wi-fi switch board 6. system fan
7. display assembly
Removing the SD Card
1. Follow the procedures in Before Working Inside Your Computer.
2. Press in on the SD card to release it from the computer.
3. Slide the SD card out of the computer.
Installing the SD Card
1. Slide the SD card into its slot until it clicks into place.
2. Follow the procedures in After Working Inside Your Computer.
Removing the Battery
1. Follow the procedures in Before Working Inside Your Computer.
2. Slide the release latch to unlock the battery.
Removing and Installing Components
11
3. Lift the battery from the computer.
Installing the Battery
1. Slide the battery into its slot until it clicks into place.
2. Follow the procedures in After Working Inside Your Computer.
12
Removing and Installing Components
Removing the Base Cover
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove battery.
3. Remove the screws that secure the base cover to the computer.
4.
Lift the base cover to remove it from the computer.
Removing and Installing Components
13
Installing the Base Cover
1. Place the base cover to align with the screw holes correctly on the computer.
2. Tighten the screws to secure the base cover to the computer.
3. Install battery.
4. Follow the procedures in After Working Inside Your Computer.
Removing the mSATA SSD card
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a. battery
b. base cover
3. To remove the mSATA SSD card:
a. Remove the screw that secures the mSATA SSD card to the computer.
b. Disconnect the mSATA SSD card from the connector on the system board.
Installing the mSATA SSD card
1. Connect the mSATA SSD card to the connector on the system board.
2. Tighten the screw to secure the mSATA SSD to the computer.
3. Install:
a. base cover
b. battery
4. Follow the procedures in After Working Inside Your computer.
Removing the Keyboard Trim
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove battery.
3. Using a plastic scribe, pry the keyboard trim to release it from the computer. Lift up to remove the keyboard trim from the
computer.
14
Removing and Installing Components
Installing the Keyboard Trim
1. Align the keyboard trim to its slot.
2. Press along the sides of the keyboard trim until it clicks in place.
3. Install battery.
4. Follow the procedures in After Working Inside Your Computer.
Removing the Keyboard
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a. battery
b. base cover
c. keyboard trim
3. Lift the battery bay and remove the screw that secures the keyboard to the computer.
4. Perform the following steps as shown in the illustration:
a. Lift the latch that secure the keyboard cable to the computer [1].
b. Disconnect the keyboard cable the computer [2].
5. Flip the computer and remove the screws that secure the keyboard to the computer.
6. Perform the following steps as shown in the illustration:
a. Slide the keyboard from the computer [1].
b. Lift the keyboard from the computer [2].
Removing and Installing Components
15
Installing the Keyboard
1. Connect the keyboard cable and tighten the screw that secures the keyboard to the computer.
2. Slide the keyboard into its compartment and ensure that it clicks into place.
3. Flip the computer, place the keyboard, and tighten the screws that secure the keyboard to the computer.
4. Install:
a. keyboard trim
b. base cover
c. battery
5. Follow the procedures in After Working Inside Your Computer.
Removing the Palmrest
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a. SD card
b. battery
c. base cover
d. keyboard trim
e. keyboard
3. Remove the screws that secure the palmrest assembly and flip the computer.
4. Perform the following steps as shown in the illustration:
a. Disconnect the cable from the computer.
b. Lift the latch that secures the keyboard cable to the computer [1].
c. Disconnect the keyboard cable [2].
d. Disconnect the touch cable from the computer [3].
e. Unroute the cables from the slot [4].
16
Removing and Installing Components
5. Remove the screws that secure the palmrest assembly to the front of the computer. Pry the edges and lift the palmrest
assembly from the computer.
Installing the Palmrest
1. Align the palm rest assembly to its original position in the computer and snap it into place.
2. Tighten the screws to secure the palmrest assembly to the front of the computer.
3. Route the touch cable and connect to the system board.
4. Tighten the screws that secure the palmrest assembly to the base of the computer.
5. Install:
a. keyboard
b. keyboard trim
c. base cover
d. battery
e. SD card
6. Follow the procedures in After Working Inside Your Computer.
Removing the WiFi Switch Board
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a. SD card
b. battery
c. base cover
d. keyboard trim
e. keyboard
f. palmrest
3. Disconnect the wi-fi switch board cable from the system board and remove the screw that secures the wi-fi swtich board to
the computer. Remove the wi-fi switch board.
Removing and Installing Components
17
Installing the WiFi Switch Board
1. Insert the wi-fi switch board in its slot.
2. Connect the wi-fi switch board to the system board.
3. Tighten the screw that secures the wi-fi switch board to the system board.
4. Install:
a. palmrest
b. keyboard
c. keyboard trim
d. base cover
e. battery
f. SD card
5. Follow the procedures in After Working Inside Your Computer.
Removing the Memory Module
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a. battery
b. base cover
3. Pry the securing clips away from the memory module until it pops up. Remove the memory module from its connector on the
system board.
Installing the Memory Module
1. Insert the memory module into the socket.
2. Press the retention clips to secure the memory module to the system board.
3. Install:
a. base cover
b. battery
4. Follow the procedures in After Working Inside Your Computer.
Removing the WLAN Card
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a. battery
b. base cover
3. Disconnect the antenna cables from the WLAN card and remove the screw that secures the WLAN card to the computer.
Remove the WLAN card from the computer.
18
Removing and Installing Components
Installing the WLAN Card
1. Insert the WLAN card into its connector at a 45degree angle into its slot.
2. Tighten the screw to secure the WLAN card to the computer.
3. Connect the antenna cables to their respective connectors marked on the WLAN card.
4. Install:
a. base cover
b. battery
5. Follow the procedures in After Working Inside Your Computer.
Removing the WWAN Card
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a. battery
b. SD card
c. base cover
3. Disconnect the antenna cables from the WWAN card.
4. Remove the screw that secures the WWAN card to the computer.
5. Disconnect the antenna cables from the WWAN card. Remove the screw that secures the WWAN card to the computer and
remove it.
Installing the WWAN Card
1. Place the WWAN card in its slot in the system board.
2. Press the WWAN card down and tighten the screw to secure the WWAN card to the computer.
3. Connect the antenna cables to their respective connectors marked on the WWAN card.
4. Install:
a. base cover
b. SD card
Removing and Installing Components
19
c. battery
5. Follow the procedures in After Working Inside Your Computer.
Removing the Display Bezel
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove the battery.
3. Pry the edges of the display bezel. Remove the display bezel from the display assembly.
Installing the Display Bezel
1. Align the display bezel in place and snap it in place.
2. Align the hinge covers on display assembly and snap it in place.
3. Install the battery
4. Follow the procedures in After Working Inside Your Computer.
Removing the Display Panel
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a. battery
b. display bezel
3. Remove the screws that secure the display panel to the display assembly. Lift the display panel over.
4. Perform the following steps as shown in the illustration:
a. Peel the LVDS cable connector tape [1].
b. Disconnect the LVDS cable from the display panel [2].
c. Remove the display panel from the display assembly [3].
20
Removing and Installing Components
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46

Dell Latitude E7240 Ultrabook Owner's manual

Category
Notebooks
Type
Owner's manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI