Dell Latitude E7240 Ultrabook Owner's manual

Brand: Dell

Model: Latitude E7240 Ultrabook

Category: Notebooks

Type: Owner's manual

Dell Latitude E7240

Owner's Manual

Regulatory Model: P22S

Regulatory Type: P22S001

April 2021

Rev. A05

Notes, cautions, and warnings

NOTE: A NOTE indicates important information that helps you make better use of your computer.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid

the problem.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

Dell

™

and the Dell logo are trademarks of Dell Inc. in the United States and/or other jurisdictions. All other marks and names mentioned herein

may be trademarks of their respective companies.

Chapter 1: Working on Your Computer...........................................................................................5

Before Working Inside Your Computer...........................................................................................................................5

Turning Off Your Computer.............................................................................................................................................. 6

After Working Inside Your Computer..............................................................................................................................6

Chapter 2: Docking Your Computer............................................................................................... 8

Chapter 3: Removing and Installing Components...........................................................................9

Recommended Tools.........................................................................................................................................................10

System Overview............................................................................................................................................................... 10

Removing the SD Card...................................................................................................................................................... 11

Installing the SD Card........................................................................................................................................................ 11

Removing the Battery........................................................................................................................................................11

Installing the Battery......................................................................................................................................................... 12

Removing the Base Cover............................................................................................................................................... 13

Installing the Base Cover..................................................................................................................................................14

Removing the mSATA SSD card.................................................................................................................................... 14

Installing the mSATA SSD card...................................................................................................................................... 14

Removing the Keyboard Trim..........................................................................................................................................14

Installing the Keyboard Trim............................................................................................................................................15

Removing the Keyboard................................................................................................................................................... 15

Installing the Keyboard..................................................................................................................................................... 16

Removing the Palmrest.................................................................................................................................................... 16

Installing the Palmrest.......................................................................................................................................................17

Removing the Wi‐Fi Switch Board.................................................................................................................................17

Installing the Wi‐Fi Switch Board...................................................................................................................................18

Removing the Memory Module.......................................................................................................................................18

Installing the Memory Module.........................................................................................................................................18

Removing the WLAN Card...............................................................................................................................................18

Installing the WLAN Card.................................................................................................................................................19

Removing the WWAN Card............................................................................................................................................. 19

Installing the WWAN Card............................................................................................................................................... 19

Removing the Display Bezel........................................................................................................................................... 20

Installing the Display Bezel..............................................................................................................................................20

Removing the Display Panel........................................................................................................................................... 20

Installing the Display Panel.............................................................................................................................................. 21

Removing the Coin-Cell Battery.....................................................................................................................................21

Installing the Coin-Cell Battery...................................................................................................................................... 22

Removing the Speakers................................................................................................................................................... 22

Installing the Speakers..................................................................................................................................................... 22

Removing the Display-Hinge Cover.............................................................................................................................. 23

Installing the Display-Hinge Cover................................................................................................................................ 23

Removing the Heatsink.................................................................................................................................................... 23

Installing the Heatsink...................................................................................................................................................... 24

Contents

Contents 3

Removing the Display Assembly.................................................................................................................................... 24

Installing the Display Assembly...................................................................................................................................... 25

Removing the System Fan.............................................................................................................................................. 26

Installing the System Fan................................................................................................................................................ 26

Removing the System Board..........................................................................................................................................26

Installing the System Board............................................................................................................................................ 27

Removing the Power Connector .................................................................................................................................. 28

Installing the Power Connector..................................................................................................................................... 28

Chapter 4: Docking Port Information........................................................................................... 29

Chapter 5: System Setup............................................................................................................ 30

Boot Sequence...................................................................................................................................................................30

Navigation Keys................................................................................................................................................................. 30

System Setup Options...................................................................................................................................................... 31

Updating the BIOS ........................................................................................................................................................... 37

System and Setup Password..........................................................................................................................................38

Assigning a System Password and Setup Password.......................................................................................... 38

Deleting or Changing an Existing System and/or Setup Password................................................................ 39

Chapter 6: Diagnostics................................................................................................................ 40

Enhanced Pre-Boot System Assessment (ePSA) Diagnostics.............................................................................. 40

Device Status Lights........................................................................................................................................................ 40

Battery Status Lights........................................................................................................................................................41

Chapter 7: Specifications............................................................................................................ 42

Chapter 8: Contacting Dell.......................................................................................................... 46

Contents

Working on Your Computer

Topics:

• Before Working Inside Your Computer

•

Turning Off Your Computer

• After Working Inside Your Computer

Before Working Inside Your Computer

Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your personal

safety. Unless otherwise noted, each procedure included in this document assumes that the following conditions exist:

● You have read the safety information that shipped with your computer.

● A component can be replaced or--if purchased separately--installed by performing the removal procedure in reverse order.

NOTE: Disconnect all power sources before opening the computer cover or panels. After you finish working inside the

computer, replace all covers, panels, and screws before connecting to the power source.

NOTE: Before working inside your computer, read the safety information that shipped with your computer. For additional

safety best practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance

CAUTION: Many repairs may only be done by a certified service technician. You should only perform

troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or

telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by

your warranty. Read and follow the safety instructions that came with the product.

CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically

touching an unpainted metal surface, such as a connector on the back of the computer.

CAUTION: Handle components and cards with care. Do not touch the components or contacts on a card. Hold a

card by its edges or by its metal mounting bracket. Hold a component such as a processor by its edges, not by

its pins.

CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable itself. Some

cables have connectors with locking tabs; if you are disconnecting this type of cable, press in on the locking

tabs before you disconnect the cable. As you pull connectors apart, keep them evenly aligned to avoid bending

any connector pins. Also, before you connect a cable, ensure that both connectors are correctly oriented and

aligned.

NOTE: The color of your computer and certain components may appear differently than shown in this document.

To avoid damaging your computer, perform the following steps before you begin working inside the computer.

1. Ensure that your work surface is flat and clean to prevent the computer cover from being scratched.

2. Turn off your computer (see Turning off Your Computer).

3. If the computer is connected to a docking device (docked), undock it.

CAUTION:

To disconnect a network cable, first unplug the cable from your computer and then unplug the

cable from the network device.

4. Disconnect all network cables from the computer.

5. Disconnect your computer and all attached devices from their electrical outlets.

6. Close the display and turn the computer upside-down on a flat work surface.

Working on Your Computer 5

NOTE: To avoid damaging the system board, you must remove the main battery before you service the computer.

7. Remove the main battery.

8. Turn the computer top-side up.

9. Open the display.

10. Press the power button to ground the system board.

CAUTION: To guard against electrical shock, always unplug your computer from the electrical outlet before

opening the display.

CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal

surface, such as the metal at the back of the computer. While you work, periodically touch an unpainted

metal surface to dissipate static electricity, which could harm internal components.

11. Remove any installed ExpressCards or Smart Cards from the appropriate slots.

Turning Off Your Computer

CAUTION: To avoid losing data, save and close all open files and exit all open programs before you turn off your

computer.

1. Shut down the operating system:

● In Windows 8:

○ Using a touch-enabled device:

a. Swipe in from the right edge of the screen, opening the Charms menu and select Settings.

b. Select the and then select Shut down

○ Using a mouse:

a. Point to upper-right corner of the screen and click Settings.

b. Click the

and select Shut down.

● In Windows 7:

a. Click Start .

b. Click Shut Down.

a. Click Start .

b. Click the arrow in the lower-right corner of the Start menu as shown below, and then click Shut

Down..

2. Ensure that the computer and all attached devices are turned off. If your computer and attached devices did not

automatically turn off when you shut down your operating system, press and hold the power button for about 4 seconds to

turn them off.

After Working Inside Your Computer

After you complete any replacement procedure, ensure you connect any external devices, cards, and cables before turning on

your computer.

CAUTION:

To avoid damage to the computer, use only the battery designed for this particular Dell computer. Do

not use batteries designed for other Dell computers.

1. Connect any external devices, such as a port replicator or media base, and replace any cards, such as an ExpressCard.

2. Connect any telephone or network cables to your computer.

Working on Your Computer

CAUTION: To connect a network cable, first plug the cable into the network device and then plug it into the

computer.

3. Replace the battery.

4. Connect your computer and all attached devices to their electrical outlets.

5. Turn on your computer.

Working on Your Computer 7

Docking Your Computer

Follow the steps to dock your computer:

a. Place the docking spacer until the docking spacer clicks on its place in the docking station.

b. Place the computer on the docking spacer to dock your

computer.

NOTE:

This docking spacer can be used to dock only the Latitude E7240 / Latitude E7440 computers. You cannot dock any

other Dell computers using this docking station.

8 Docking Your Computer

Removing and Installing Components

This section provides detailed information on how to remove or install the components from your computer.

Topics:

• Recommended Tools

• System Overview

• Removing the SD Card

• Installing the SD Card

• Removing the Battery

• Installing the Battery

• Removing the Base Cover

• Installing the Base Cover

• Removing the mSATA SSD card

• Installing the mSATA SSD card

• Removing the Keyboard Trim

• Installing the Keyboard Trim

• Removing the Keyboard

• Installing the Keyboard

• Removing the Palmrest

• Installing the Palmrest

• Removing the Wi‐Fi Switch Board

• Installing the Wi‐Fi Switch Board

• Removing the Memory Module

• Installing the Memory Module

• Removing the WLAN Card

• Installing the WLAN Card

• Removing the WWAN Card

• Installing the WWAN Card

• Removing the Display Bezel

• Installing the Display Bezel

• Removing the Display Panel

• Installing the Display Panel

• Removing the Coin-Cell Battery

• Installing the Coin-Cell Battery

• Removing the Speakers

• Installing the Speakers

• Removing the Display-Hinge Cover

• Installing the Display-Hinge Cover

• Removing the Heatsink

• Installing the Heatsink

• Removing the Display Assembly

• Installing the Display Assembly

• Removing the System Fan

• Installing the System Fan

• Removing the System Board

• Installing the System Board

• Removing the Power Connector

• Installing the Power Connector

Removing and Installing Components 9

Recommended Tools

The procedures in this document may require the following tools:

● Small flat-blade screwdriver

● Phillips screwdriver

● Small plastic scribe

System Overview

Figure 1. Inside View — Back

1. system fan

2. mSATA card

3. battery bay

4. SD card

5. WLAN card

6. WWAN card

7. memory module

8. heatsink

Figure 2. Inside view — Front

Removing and Installing Components

1. coin-cell battery 2. SIM card board

3. speaker 4. system board

5. wi-fi switch board 6. system fan

7. display assembly

Removing the SD Card

1. Follow the procedures in Before Working Inside Your Computer.

2. Press in on the SD card to release it from the computer.

3. Slide the SD card out of the computer.

Installing the SD Card

1. Slide the SD card into its slot until it clicks into place.

2. Follow the procedures in After Working Inside Your Computer.

Removing the Battery

1. Follow the procedures in Before Working Inside Your Computer.

2. Slide the release latch to unlock the battery.

Removing and Installing Components

3. Lift the battery from the computer.

Installing the Battery

1. Slide the battery into its slot until it clicks into place.

2. Follow the procedures in After Working Inside Your Computer.

Removing and Installing Components

Removing the Base Cover

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove battery.

3. Remove the screws that secure the base cover to the computer.

Lift the base cover to remove it from the computer.

Removing and Installing Components

Installing the Base Cover

1. Place the base cover to align with the screw holes correctly on the computer.

2. Tighten the screws to secure the base cover to the computer.

3. Install battery.

4. Follow the procedures in After Working Inside Your Computer.

Removing the mSATA SSD card

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. base cover

3. To remove the mSATA SSD card:

a. Remove the screw that secures the mSATA SSD card to the computer.

b. Disconnect the mSATA SSD card from the connector on the system board.

Installing the mSATA SSD card

1. Connect the mSATA SSD card to the connector on the system board.

2. Tighten the screw to secure the mSATA SSD to the computer.

3. Install:

a. base cover

b. battery

4. Follow the procedures in After Working Inside Your computer.

Removing the Keyboard Trim

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove battery.

3. Using a plastic scribe, pry the keyboard trim to release it from the computer. Lift up to remove the keyboard trim from the

computer.

Removing and Installing Components

Installing the Keyboard Trim

1. Align the keyboard trim to its slot.

2. Press along the sides of the keyboard trim until it clicks in place.

3. Install battery.

4. Follow the procedures in After Working Inside Your Computer.

Removing the Keyboard

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. base cover

c. keyboard trim

3. Lift the battery bay and remove the screw that secures the keyboard to the computer.

4. Perform the following steps as shown in the illustration:

a. Lift the latch that secure the keyboard cable to the computer [1].

b. Disconnect the keyboard cable the computer [2].

5. Flip the computer and remove the screws that secure the keyboard to the computer.

6. Perform the following steps as shown in the illustration:

a. Slide the keyboard from the computer [1].

b. Lift the keyboard from the computer [2].

Removing and Installing Components

Installing the Keyboard

1. Connect the keyboard cable and tighten the screw that secures the keyboard to the computer.

2. Slide the keyboard into its compartment and ensure that it clicks into place.

3. Flip the computer, place the keyboard, and tighten the screws that secure the keyboard to the computer.

4. Install:

a. keyboard trim

b. base cover

c. battery

5. Follow the procedures in After Working Inside Your Computer.

Removing the Palmrest

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. SD card

b. battery

c. base cover

d. keyboard trim

e. keyboard

3. Remove the screws that secure the palmrest assembly and flip the computer.

4. Perform the following steps as shown in the illustration:

a. Disconnect the cable from the computer.

b. Lift the latch that secures the keyboard cable to the computer [1].

c. Disconnect the keyboard cable [2].

d. Disconnect the touch cable from the computer [3].

e. Unroute the cables from the slot [4].

Removing and Installing Components

5. Remove the screws that secure the palmrest assembly to the front of the computer. Pry the edges and lift the palmrest

assembly from the computer.

Installing the Palmrest

1. Align the palm rest assembly to its original position in the computer and snap it into place.

2. Tighten the screws to secure the palmrest assembly to the front of the computer.

3. Route the touch cable and connect to the system board.

4. Tighten the screws that secure the palmrest assembly to the base of the computer.

5. Install:

a. keyboard

b. keyboard trim

c. base cover

d. battery

e. SD card

6. Follow the procedures in After Working Inside Your Computer.

Removing the Wi‐Fi Switch Board

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. SD card

b. battery

c. base cover

d. keyboard trim

e. keyboard

f. palmrest

3. Disconnect the wi-fi switch board cable from the system board and remove the screw that secures the wi-fi swtich board to

the computer. Remove the wi-fi switch board.

Removing and Installing Components

Installing the Wi‐Fi Switch Board

1. Insert the wi-fi switch board in its slot.

2. Connect the wi-fi switch board to the system board.

3. Tighten the screw that secures the wi-fi switch board to the system board.

4. Install:

a. palmrest

b. keyboard

c. keyboard trim

d. base cover

e. battery

f. SD card

5. Follow the procedures in After Working Inside Your Computer.

Removing the Memory Module

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. base cover

3. Pry the securing clips away from the memory module until it pops up. Remove the memory module from its connector on the

system board.

Installing the Memory Module

1. Insert the memory module into the socket.

2. Press the retention clips to secure the memory module to the system board.

3. Install:

a. base cover

b. battery

4. Follow the procedures in After Working Inside Your Computer.

Removing the WLAN Card

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. base cover

3. Disconnect the antenna cables from the WLAN card and remove the screw that secures the WLAN card to the computer.

Remove the WLAN card from the computer.

Removing and Installing Components

Installing the WLAN Card

1. Insert the WLAN card into its connector at a 45–degree angle into its slot.

2. Tighten the screw to secure the WLAN card to the computer.

3. Connect the antenna cables to their respective connectors marked on the WLAN card.

4. Install:

a. base cover

b. battery

5. Follow the procedures in After Working Inside Your Computer.

Removing the WWAN Card

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. SD card

c. base cover

3. Disconnect the antenna cables from the WWAN card.

4. Remove the screw that secures the WWAN card to the computer.

5. Disconnect the antenna cables from the WWAN card. Remove the screw that secures the WWAN card to the computer and

remove it.

Installing the WWAN Card

1. Place the WWAN card in its slot in the system board.

2. Press the WWAN card down and tighten the screw to secure the WWAN card to the computer.

3. Connect the antenna cables to their respective connectors marked on the WWAN card.

4. Install:

a. base cover

b. SD card

Removing and Installing Components

c. battery

5. Follow the procedures in After Working Inside Your Computer.

Removing the Display Bezel

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove the battery.

3. Pry the edges of the display bezel. Remove the display bezel from the display assembly.

Installing the Display Bezel

1. Align the display bezel in place and snap it in place.

2. Align the hinge covers on display assembly and snap it in place.

3. Install the battery

4. Follow the procedures in After Working Inside Your Computer.

Removing the Display Panel

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. display bezel

3. Remove the screws that secure the display panel to the display assembly. Lift the display panel over.

4. Perform the following steps as shown in the illustration:

a. Peel the LVDS cable connector tape [1].

b. Disconnect the LVDS cable from the display panel [2].

c. Remove the display panel from the display assembly [3].

Removing and Installing Components

Page is loading ...

Dell Latitude E7240 Ultrabook Owner's manual

Brand: Dell

Model: Latitude E7240 Ultrabook

Category: Notebooks

Type: Owner's manual

Download PDF

report

Dell Latitude E7240 Ultrabook Owner's manual

Dell Latitude E7240 Ultrabook Owner's manual

Related papers

Other documents