Crate V212T User manual

Crate
Brand
Crate
Model
V212T
Type
User manual

Crate V212T

The Crate V212T is a 2x12" guitar speaker enclosure that is loaded with two Tone Tubby speakers. It has a power rating of 160 watts RMS and a peak power handling of 320 watts. The frequency response is 80Hz - 5kHz and the sensitivity is 96.1 dB SPL 1 watt/1 meter. The inputs are two 1/4" jacks. It weighs 67 lbs and the dimensions are 28" x 19-7/8" x 11".

The V212T is a great choice for guitarists who are looking for a powerful and portable speaker enclosure. It is perfect for use in a variety of settings, from small clubs to large arenas. The tilt-back legs allow you to angle the cabinet for better sound projection, and the casters make it easy to transport.

Crate V212T

The Crate V212T is a 2x12" guitar speaker enclosure that is loaded with two Tone Tubby speakers. It has a power rating of 160 watts RMS and a peak power handling of 320 watts. The frequency response is 80Hz - 5kHz and the sensitivity is 96.1 dB SPL 1 watt/1 meter. The inputs are two 1/4" jacks. It weighs 67 lbs and the dimensions are 28" x 19-7/8" x 11".

The V212T is a great choice for guitarists who are looking for a powerful and portable speaker enclosure. It is perfect for use in a variety of settings, from small clubs to large arenas. The tilt-back legs allow you to angle the cabinet for better sound projection, and the casters make it easy to transport.

V212T GUITAR SPEAKER ENCLOSURE
IMPORTANT SAFETY INSTRUCTIONS:
1.Read, follow and keep these instructions. Heed all warnings.
2.This speaker is capable of producing high sound pressure levels that may cause
permanent hearing damage. User caution is advised and ear protection is recom-
mended during use.
3.This speaker is designed for use on a sturdy, level surface. Whenever stacking
speaker cabinets, do not stack more than two high. Only speaker cabinets which
are equipped with caster cups on their top surfaces are to be used underneath a
cabinet which is equipped with casters.
4.Speaker cables are a tripping hazard and must be routed out of traffic areas and
away from any possible accidental contact.
5.Do not expose this speaker to rain or moisture. Do not place liquid filled contain-
ers on this speaker. Clean only with a damp cloth.
6.Repair or service of this speaker should be performed only by qualified personnel.
Your V-Series V212T 2x12 Guitar Speaker Enclosure is built from
the finest materials and components available. This cabinet is
loaded with two Tone Tubby speakers and comes standard with
casters, steel handles, heavy duty metal tilt back legs, Switchcraft
metal jacks on a metal input plate, and hardware for “piggy back”
mounting of the V30H V-Series guitar amplifier head.
The tilt back stands allow the cabinet to slant back at a 40
o
angle
to improve your ability to hear yourself, especially on smaller
stages. Heavy duty fastening posts on the top of the enclosure are
provided for secure locking of the V30H amp head, resulting in a
piggy back combo amp that can actually be used in the tilt back
position.
The V212T also makes an excellent extension cabinet for any
V-Series guitar amplifier with a minimum load of 8 ohms.
V212T GUITAR SPEAKER ENCLOSURE
The tilt back legs lock flat against the cabinet
when not in use - tighten the securing fasteners
completely to eliminate rattling.
Crate’s V30H amp head is designed to “piggy
back” mount onto the V212T enclosure. The V30H
has slide-out mounting hardware which lock onto
the posts on the top of the V212T. Loosen the
knobs on the posts, slide the amp in place and lock
down the knobs.
The piggy-backed amp can be rolled around
on its casters by the amp head’s handle, but do
not try to pick the combo up by the amp head or
its handle.
The casters are to be removed before using the
cabinet in the tilt back mode. Swing each tilt back
leg into position and secure all hardware before
leaning the cabinet back. Do not allow the unit to
fall back on its own, rather, lower it into
position.(The cabinet should not be tilted back on
slick or smooth surfaces.)
V212T GUITAR SPEAKER ENCLOSURE
TECHNICAL SPECIFICATIONS:
IMPEDANCE 8 ohms
RMS POWER RATING 160 watts
PEAK POWER HANDLING 320 watts
FREQUENCY RESPONSE 80Hz - 5kHz
SENSITIVITY 96.1 dB SPL 1 watt/1 meter
MAXIMUM SPL 94 dB
TRANSDUCERS (2) Tone Tubby 12” 16 ohm speakers
INPUTS (2) 1/4” jacks
DIMENSIONS (H x W x D) 28” x 19-7/8” x 11”
WEIGHT 67 lbs
The V212T is covered with a durable Tolex material: wipe it clean with a lint-free cloth.
Never spray cleaning agents onto the cabinet. Avoid abrasive cleansers which would damage the finish.
Specifications and information in this manual are subject to change without notice.
www.v-seriesamps.com
©2004 St. Louis Music, Inc • 1400 Ferguson Avenue • St. Louis, MO 63133
47-953-01 • 122104
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Crate V212T User manual

Crate
Brand
Crate
Model
V212T
Type
User manual

Crate V212T

The Crate V212T is a 2x12" guitar speaker enclosure that is loaded with two Tone Tubby speakers. It has a power rating of 160 watts RMS and a peak power handling of 320 watts. The frequency response is 80Hz - 5kHz and the sensitivity is 96.1 dB SPL 1 watt/1 meter. The inputs are two 1/4" jacks. It weighs 67 lbs and the dimensions are 28" x 19-7/8" x 11".

The V212T is a great choice for guitarists who are looking for a powerful and portable speaker enclosure. It is perfect for use in a variety of settings, from small clubs to large arenas. The tilt-back legs allow you to angle the cabinet for better sound projection, and the casters make it easy to transport.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents