2. Home
  3. Domestic appliances
  4. Climate control
  5. Fireplaces
  6. FMI
  7. SLK

FMI SLK Operating instructions

  • Hello! I am an AI chatbot trained to assist you with the FMI SLK Operating instructions. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
www.fmiproducts.com
FIELD FABRICATED SHROUDS
These shroud designs have been certied and tested for FMI PRODUCTS,LLC replace systems for use with Round Top
Termination Series for 8" (RT/RTT/RTL/RTTL-8DM), 10" (RTL-10DM), 12" (RTL-12D), direct vent and b-vent terminations.
These shroud designs must be constructed from a minimum 26 ga. aluminized steel and may be eld constructed if dimen-
sional requirements specied in Figures 1 through 6 are maintained. Note: All dimensions are minimum.
Figure 1 - Standard Arch Shroud
Figure 2 - Bishops Arch Shroud
Figure 3 - Square Shroud
Figure 4 - Square Shroud (Tapered)
Figure 5 - Square Shroud
Figure 6 - Square Shroud (Tapered)
www.fmiproducts.com
108180-01G
2
SHROUD INSTALLATION
The Round Top Termination should be installed completely
before installing shroud. A 6" minimum clearance must be
maintained between bottom of termination and top of ashing
(see Figure 7). Place shroud over chase top ashing and secure
with sheet metal screws (see Figure 8). IMPORTANT: Refer to
installation instructions supplied with your FMI PRODUCTS,
LLC termination cap model for minimum clearances.
6" Minimum
Round Top
Termination
Chase Top
Flashing
Figure 7 - 6" Minimum Clearance
Figure 8 - Shroud Installation
Square
Shroud Shown
Chase Top
Flashing
Chase
CONSTRUCTING CHASE TOP FLASHING
Fabricate ashing with the required diameter hole centered
over chimney end (see Figure 9).
As Required
“X” Minimum
Collar
Min. 28 GA
Galvanized Steel
Figure 9 - Chase Top Flashing
PIPE SYSTEM X
8" Wood Burning 14"
10" Wood Burning 16
1
/
2
"
12" Wood Burning 16
1
/
2
"
Direct Vent 9
1
/
2
"
INSTALLATION OF FMI PRODUCTS, LLC
FABRICATED SHROUD LEGS (MODEL SLK)
FMI PRODUCTS, LLC fabricated shroud legs can be used to
provide a 3" opening between bottom of shroud and chase
top ashing. The Shroud Leg Kit (SLK) contains 4 shroud legs
and 24 self-drilling screws. Use the following instructions to
install shroud legs.
1. Place chase ashing on top of shroud leg tabs (bent).
2. Secure shroud legs with self-drilling screws as shown in
Figure 10. Note: Both corner edges should be ush.
3. Repeat this procedure for each corner of shroud.
Figure 10 - Shroud Leg Installation
Shroud
Chase Top
Flashing
3" Min.
Height
Shroud Leg
Self-Drilling
Screws (6x)
www.fmiproducts.com
108180-01G
3
_____________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
_____________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
_____________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
NOTES
108180-01
Rev. G
03/10
2701 S. Harbor Blvd.
Santa Ana, CA 92704
1-866-328-4537
www.fmiproducts.com
/