Star Trac 728-0005 User manual

LCD Attachment

Installation and

Service Manual

2

1

Table of Contents

Parts List ................................................................................................2

Hardware Kits ........................................................................................3

Bike, Cross Trainer and Stepper Start ....................................................

4

Steps in Assembling the Bracket ............................................................5

Installation Instructions (Bike, Cross Trainer & Stepper) .......................

6

Installation Instructions (Bike, Cross Trainer & Stepper) Cont’d ............

7

Installation Instructions (Bike, Cross Trainer & Stepper) Cont’d ............

8

Installation Instructions (Bike, Cross Trainer & Stepper) Cont’d ............

9

Final Installation (Bike, Cross Trainer & Stepper) .................................10

Treadmill Start ......................................................................................

11

Steps in Assembling the Bracket ..........................................................12

Treadmill Installation Instructions .......................................................

13

Treadmill Installation Instructions (Cont’d) .........................................

14

Treadmill Installation Instructions (Cont’d) .........................................

15

Treadmill Installation Instructions (Cont’d) .........................................

16

Treadmill Installation Instructions (Cont’d) .........................................

17

Final Installation (Treadmill) .................................................................

18

Maintenance Requirements ..................................................................19

Club Owner Guide ................................................................................20

Club Owner Guide (Cont’d) ..................................................................21

A/V Installer’s Guide .............................................................................

22

A/V Installer’s Guide

(Cont’d) ..............................................................23

A/V Installer’s Guide

(Cont’d) ..............................................................24

A/V Installer’s Guide

(Cont’d) ..............................................................25

A/V Installer’s Guide

(Cont’d) ..............................................................26

A/V Install - Wire Management ............................................................27

2

All Kits include:

Before installing the TV bracket verify that you have the proper kit according to the list above and that all the

parts are included. If any of the items are missing call StarTrac at 800-503-1221 to order a replacement kit.

Parts List (All Machines)

Product Model ................................................................................... Kit Part Number

Pro Tread .......................................................................................................715-3628

Pro Stepper ....................................................................................................711-3178

Pro Bike Upright .............................................................................................718-5079

Pro Bike Recumbent ......................................................................................720-0087

CrossTrainer ...................................................................................................721-1093

Neck Mounting support assembly

(Crossbow)

Mounting braces

(Wings)

Monitor Interface

(Gooseneck)

Clamp top and bottom with pad

Wire management

*Not included in kit 715-3628 (Pro Tread)

3

Hardware Kits

Kit No.728-0005 (Hardware Kit for Bikes, Stepper and CrossTrainer)

Kit No.728-0006 (Hardware Kit for Pro Treadmills)

4

Bike, CrossTrainer and Stepper

5

Steps in Assembling the Bracket

Bike, CrossTrainer and Stepper

This pictorial view shows the assembly of the TV bracket in. The following

pages describe the install process.

(Final assembled bracket)

6

Installation Instructions

Tools required for Bike, CrossTrainer, and Stepper (not supplied):

• 5mm or 3/16” Allen wrench (Crossbow and clamp screws)

• 1/8” or 3mm Allen wrench (Neck screws)

• #2 Phillips Screwdriver (Wing screws)

• 7/16” or 11MM open end wrench (Cross bow screws)

Bike, CrossTrainer and Stepper

1

Remove the four screws from the display.

(Screws are no longer needed)

2

Attach the wings into the back of the display using

the Phillips head screws.

NOTE: The longer screws go in the 2 bottom

holes and the shorter screws in the 2 top holes.

Failure to follow this will result in damage to the

display.

Align the wings on the crossbow so the curved edge

is facing the inside and the smooth edge on the

outside as shown in the diagram.

7

Installation Instructions (Cont’d)

Bike, CrossTrainer and Stepper

3

- Attach the crossbow to the wings.

- Tighten the two nuts with the 7/16” or 11MM open

end wrench as shown.

4

Slide the top mounting plate on the neck and align the

top plate notch with the neck base notch.

Make sure top plate sits ﬂ ush on the notch.

8

Installation Instructions (Cont’d)

Bike, CrossTrainer and Stepper

5

NOTE: Before tightening, make sure

base of bracket neck is ﬂush with

ﬁtness product.

NO

YES

5

- Insert the rubber pad onto the bottom mounting plate

and attach the plate around the neck of the product.

- Using the remaining 4 screws, attach the bottom and

top mounting plates together.

- Check ﬁt and alignment and make any necessary

adjustments, tighten all the screws securely.

Continued

9

Bike, CrossTrainer and Stepper

7

- Slide the top monitor support bracket (Gooseneck)

and lower over neck.

- Secure the gooseneck by inserting the 4 ﬂat head

screws and tighten securely.

-

Use any 4 holes to adjust TV height. See A/V install

section for more info.

Installation Instructions (Cont’d)

Bike, CrossTrainer and Stepper

- Put the crossbow back plate in position and insert

the two socket head cap screws by hand.

- Tighten

the 2 screws into the cross bow using the

9/16” Allen wrench.

6

*Save wire management for A/V install — see A/V section.

10

The ﬁnal installation will look like theses photos.

Final Installation

Bike, CrossTrainer and Stepper

Pro Bikes

Pro StepperCross Trainer

Recumbent

Cross Trainer

Stepper

Upright

Bike, CrossTrainer and Stepper

11

For all Pro Treadmills

12

All Treadmills

Steps in Assembling the Bracket

This pictorial view shows the assembly of the TV bracket in. The following

pages describe the install process.

13

1

Remove the four screws from the tread display

as shown.

(Screws are no longer needed)

Treadmill Installation Instructions

Tools required for treadmill (not supplied):

• 5mm or 3/16 Allen wrench (Crossbow and clamp screws)

• 1/8 “ Allen wrench (Neck screws)

• #2 Phillips Screwdriver (Wings screws)

• 7/16” or 11MM open end wrench (Crossbow screws)

CAUTION: UNPLUG THE TREADMILL BEFORE PROCEEDING.

All Treadmills

14

2

Attach the wings into the back of the display using

the Phillips head screws.

NOTE: The longer screws go in the 2 bottom

holes and the shorter screws in the 2 top holes.

Failure to follow this will result in damage to the

display.

Align the wings on the crossbow so the curved edge

is facing the inside and the smooth edge on the

outside as shown in the diagram.

All Treadmills

Treadmill Installation Instructions (Cont’d)

3

Attach the crossbow to the wings and leave the

nuts slightly loose so you can position them onto

the display, do not attach the back of the crossbow

at this time.

Tighten the two nuts with the 7/16” or 11MM open

end wrench as shown.

15

4

5

All Treadmills

Treadmill Installation Instructions (Cont’d)

Slide the top mounting plate on the neck and align the

top plate notch with the neck base notch.

Make sure top plate sits ﬂ ush on the notch.

- Insert the rubber pad onto the bottom mounting plate

and attach the plate around the neck of the product.

- Using the remaining 4 screws, attach the bottom and

top mounting plates together.

- Check ﬁ t and alignment and make any necessary

adjustments, tighten all the screws securely.

16

All Treadmills

Treadmill Installation Instructions (Cont’d)

7

- Slide the top monitor support bracket (Gooseneck)

and lower it over neck.

- Secure the gooseneck by inserting the 4 ﬂat head

screws and tighten securely.

-

Use any 4 holes to adjust TV height. See A/V install

section for more info.

- Holding the bracket base against the product neck,

put the crossbow back plate in position and insert

the two socket head cap screws by hand.

- Tighten

the 2 screws into the cross bow using the

9/16” Allen wrench.

NOTE: Before tightening, make sure base of neck is ﬂush.

NO

YES

5

Continued

6

17

*Save wire management for A/V install — see A/V section.

Vibration

- Secure the Handrails -

The handrails of the treadmill need to be adjusted. Replacing the existing

washers with thicker ones will make the handrails more secure.

NOTE: Take care not to use power tools on the long handrail

bolt, as this will break the bolt in the handrail.

8

A - Plug in tread

B - Elevate the treadmill

, then unplug

C - Remove the two long bolts that hold the

handrails to the base of the treadmill.

D - Replace the existing washers with the new

thicker washer for added stability.

CAUTION: Do not use power tools. The bolt can

break in the handrail.

All Treadmills

Treadmill Installation Instructions (Cont’d)

18

All Treadmills

The ﬁ nal installation will look like theses photos.

Treadmills

Final Installation

Page is loading ...

Star Trac 728-0005 User manual

Star Trac 728-0005 User manual

Related papers

Other documents