Chromalox DTS-HAZ Installation guide

Chromalox
Brand
Chromalox
Model
DTS-HAZ
Type
Installation guide

This manual is also suitable for

Chromalox DTS-HAZ is a wall mount kit for the industrial-grade DTS-HAZ device, which is compliant with UL/cUL and Class 1, Division 2 safety standards. It is ideal for mounting the DTS-HAZ on a vertical surface, ensuring proper airflow and maintaining compliance with safety regulations. The kit includes two stainless steel mounting brackets and the necessary hardware, making the installation process quick and easy.

The DTS-HAZ is designed to be mounted with the heat sink fins oriented vertically to prevent debris accumulation and maintain optimal cooling. It features a mounting plate kit, available as an optional accessory, to facilitate installation on vertical surfaces.

Chromalox DTS-HAZ is a wall mount kit for the industrial-grade DTS-HAZ device, which is compliant with UL/cUL and Class 1, Division 2 safety standards. It is ideal for mounting the DTS-HAZ on a vertical surface, ensuring proper airflow and maintaining compliance with safety regulations. The kit includes two stainless steel mounting brackets and the necessary hardware, making the installation process quick and easy.

The DTS-HAZ is designed to be mounted with the heat sink fins oriented vertically to prevent debris accumulation and maintain optimal cooling. It features a mounting plate kit, available as an optional accessory, to facilitate installation on vertical surfaces.

1
Installation Instructions
MP-2
Wall Mount Kit for DTS-HAZ
PJ947
0037-75529
March 2013
2
Installation Instructions
General
The Wall Mount Kit provides an alternative mounting
option for the DTS-HAZ.
To maintain UL/cUL and Class 1, Division 2
compliance, the conditions must be met:
1. When not using the Pipe Standoff Mount, the
optional Wall Mounting Bracket Kit: MP-2
DTS-HAZ Mounting Plate Kit must be used.
2. The DTS-HAZ must be mounted on vertical
surface.
3. The Heat Sink Fins on the rear of the DTS
must be oriented vertically and they must be
kept free of debris at all times.
4. We suggest that the installation be done by
qualified personnel or professionals.
Installation
1. The kit comes complete with two stainless steel
mounting brackets and the necessary hardware to
mount the brackets to the DTS-HAZ.
2. Remove the front cover of the DTS-HAZ. Place one
screw into the DTS through hole. Attach bracket
and secure with washer and nut.
3. When installing the DTS on a vertical surface, the
Pipe Standoff is not used and is typically replaced
by rigid 1” NPT conduit. The conduit shall terminate
into the bottom of the Compression Fitting. See
manual PJ944 for the complete instructions.
4. Both the vertical wall material and the fasteners
used to mount the DTS must be of suitable indus-
trial grade quality.
5. Use the above Wall Mount Layout dimensions to lo-
cate the 4 hole locations on the vertical surface to
which the DTS will be mounted.
6. Should the owner use other means to mount the
DTS to a vertical surface, a minimum of 3 inches (76
mm) must be maintained between the rear of the
DTS-HAZ and the mounting surface. This will allow
adequate airflow across the heat sink of the DTS.
The supports must not restrict any airflow from ei-
ther the top or the bottom of the heat sink. Viola-
tion of this voids UL/cUL and suitability for Class I,
Division 2 areas and potentially creates a harmful
condition.
1347 HEIL QUAKER BLVD., LAVERGNE, TN 37086
Phone: (615) 793-3900 www.chromalox.com
Limited Warranty:
Please refer to the Chromalox limited warranty applicable to this product at
http://www.chromalox.com/customer-service/policies/termsofsale.aspx.
.657
[16.69mm]
.875
[22.23mm]
.875
[22.23mm]
Ø.390 [Ø9.91mm]
Ø.218 [Ø5.54mm]
3.000
[76.20mm]
RECOMMENDED - WALL MOUNT LAYOUT
MAXIMUM #10 STUD
Bracket Material:
16 ga Stainless Steel
0.059 " (1.5mm) nominal
7.750 [196.85mm]
4.500
[114.30mm]
  • Page 1 1
  • Page 2 2

Chromalox DTS-HAZ Installation guide

Chromalox
Brand
Chromalox
Model
DTS-HAZ
Type
Installation guide
This manual is also suitable for

Chromalox DTS-HAZ is a wall mount kit for the industrial-grade DTS-HAZ device, which is compliant with UL/cUL and Class 1, Division 2 safety standards. It is ideal for mounting the DTS-HAZ on a vertical surface, ensuring proper airflow and maintaining compliance with safety regulations. The kit includes two stainless steel mounting brackets and the necessary hardware, making the installation process quick and easy.

The DTS-HAZ is designed to be mounted with the heat sink fins oriented vertically to prevent debris accumulation and maintain optimal cooling. It features a mounting plate kit, available as an optional accessory, to facilitate installation on vertical surfaces.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents