KitchenAid KDIX 8810 Installation guide

KDIX 8810
KitchenAid
Brand
KitchenAid
Model
KDIX 8810
Category
Sanitary ware
Type
Installation guide
KDIX 8810
Installation instructions
Dishwasher safety 4
Installation requirements 5
Installation instructions 7
4
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and
obey all safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or
“WARNING.” These words mean:
DANGER You can be killed or seriously injured if you don't immediately follow these
instructions.
WARNING You can be killed or seriously injured if you don't follow these instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury,
and tell you what can happen if these instructions are not followed.
Dishwasher safety
• This dishwasher is manufactured for indoor use only.
• Observe all governing codes and ordinances.
• Install this dishwasher as specified in these instructions.
• Installation should be performed by a qualified service technician. The dishwasher must be installed to
meet all electrical and plumping national and local codes and ordinances.
5
Installation requirements
557 mm
total depth
525 mm
between clamp rails
Location Requirements
Protect the dishwasher and water lines leading to
the dishwasher against freezing. Damage caused by
freezing is not covered by the warranty.
If the dishwasher will be left unused for a period of
time, or in a location where it may be subject to
freezing, we recommend having it ‘winterised’ by
PRODUCT DIMENSIONS
our authorised service personnel. Please contact
our Customer Care Centre.
The dishwasher is shipped ready for installation of
a one hole tap unit. If a two, three, or four hole tap
unit is to be installed, the holes must be cut by a
qualified plumber, according to the Tap unit
manufacturer’s specifications.
3-prong ground type power supply cord - 1045 mm.
CABINET REQUIREMENTS
*NOTE: The coutout must be accurately cut to the dimensions shown within
1,6 mm. Dishwasher top flange overlaps the countertop cutout by 11 mm on
front and back edges and 6,4 mm on sides.
• Cabinetry and countertop must be sturdy enough to support loaded
dishwasher and sink (180 kg).
Radius: 57 mm
Radius: 25 mm
the right back corner must be
cut to this radius
Back right corner: If countertop is
more than 19 mm thick, measure
down 19 mm and cut 45° bevel all the
way around radius.
CRITICAL
RADIUS
11 mm min.
flat surface required
537 mm
(see *NOTE)
For base cabinet
installations, min. 914 mm
width required
864 mm
(see *NOTE)
537 mm
(see *NOTE)
It is recommended that sink
water and drain line
connections be located on
this side of cabinet
It is recommended
that dishwasher
water and drain line
connections be
located on this side
of cabinet
635 mm
deep countertop.
Countertop must
be level
Backsplash
531 mm
561 mm
504 mm
to centre of
check valve
254 mm
dishwasher drain
877 mm
total width
275 mm
to centre
of hole
tap unit
500 mm
maximum
opened
lid height
209 mm
height of sink
166 mm
centre
of
sink drain
856 mm
between
clamp rails
357 mm
centre of
tub drain
Factory
istalled
air gaps
GFCI
(TEST button)
32 mm
19 mm
44 mm
to centre of
hole tap unit
6
Separate drain trap for the sink and dishwasher
must be provided.
Dishwasher drain:
If the dishwasher drain exits through the back wall,
the centreline of the drain pipe must be a minimum
of 15 mm below the drain trap outlet. Drain pipe
must go down on its whole length. This is required
to completely drain the dishwasher tub so that no
standing water remains in tub. Connection
between dishwasher drain and drain pipe must be
done by pipe with diameter minimum ø 50 mm.
WATER SUPPLY REQUIREMENTS
For dishwasher:
Hot water line with 0.3-10 bar water pressure.
49°C (120°F) water at dishwasher.
For sink tap unit:
• Hot and cold water lines.
ELECTRICAL REQUIREMENTS
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instuctions can result in
death, fire, or electrical shock.
• If codes permit and a separate ground wire is
used, it is recommended that a qualified
electrician determine that the ground path is
adequate.
• Do not ground to a gas pipe.
• Check with a qualified electrician if you are not
sure the dishwasher is properly grounded.
• Do not have a fuse in the neutral or ground
circuit.
Garbage Disposer
If you plan to install a garbage disposer, an
additional separate electrical supply is required.
Recommended ground method
For your personal safety, this appliance must be
grounded. This appliance is equipped with a power
supply cord having a 3 prong ground plug. To
minimise possible shock hazard, the cord must be
plugged into a mating 3 prong ground-type outlet,
grounded in accordance with local codes and
ordinances.
If a mating outlet is not available, it is the personal
responsibility and obligation of the customer to
have a properly grounded 3 prong outlet installed
by a qualified electrician.
Installation requirements
water- pipe
network
back
wall
15 mm
561 mm
7
Installation instructions
PREPARE DISHWASHER
1. With a utility knife, cut along the back right
corner of inner carton.
2. Remove inner carton. Leave dishwasher on
bottom pad.
3. Install tap unit (not included). The dishwasher is
shipped ready for installation of a one-hole tap
unit. If a two-, three-, four-hole faucet is to be
installed, the holes must be cut by a qualified
plumber according to the tap unit
manufacturer’s specifications.
INSTALL DISHWASHER
1. Mark countertop and apply a 6÷7 mm bead of
silicone caulk 6÷7 mm away from dishwasher
cutout on sides and 11 mm on front and back.
WARNING
Excessive Weight Hazard
Use two or more people to move and install
dishwasher.
Failure to do so can result in back or other injury.
IMPORTANT:
To prevent damage to right-hand hinge, open
dishwasher lid before setting dishwasher into
countertop cutout.
2. Set the dishwasher into countertop cutout.
Make sure front of dishwasher is parallel to
front edge of countertop.
3. After complete installation dishwasher should be
fully fixed by silicone. For additional support you
can use included clamps and brackets:
• Install two clamps, evenly spaced, on front
(sink) side clamp rail. To install clamps:
- hook upper clamp onto rail; use flat-blade
screwdriver to attach clamp to rail,
- use 11 mm deep-well socket and securely
tighten nut against lower clamp. Do not
overtighten.
• Install two brackets on right bottom side of
dishwasher. To install brackets:
- use screwdriver with torx tip to attach bracket
to bottom of dishwasher,
- use cross-blade screwdriver to attach bracket
to cabinet.
6÷7 mm
bead of silicone
cault
dishwasher
cutout
Cut along
this corner
Back of
inner carton
rail
countertop
upper clamp
lower clamp
sink
8
4. Immediately remove any excess caulking. Read
Instruction for Use of silicone to know time,
which silicone need to full durability. Do not use
dishwasher until silicone has full durability.
MAKE ELECTRICAL CONNECTION
Using a power supply cord.
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in
death, fire, or electrical shock.
Plug into a grounded 3 prong outlet.
CONNECT WATER SUPPLY
1. Connect the dishwasher water fill line.
2. Connect hot and cold water lines to the tap
unit.
3. Connect the sink and dishwashing drain
plumbing.
4. Turn water supply on the both dishwasher and
sink tap unit. Check for leaks.
COMPLETE INSTALLATION
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in
death, fire, or electrical shock.
1. Plug in dishwasher or reconnect power.
IMPORTANT:
The following steps must be done before using the
dishwasher, to test and activate the GFCI.
Water inlet valve
Check valve
Do not remove
check valve!
Water
fill line
connection
Installation instructions
9
Installation instructions
1. Unscrew two bolts (A) and remove GFCI cover
(B) located on the front base of the dishwasher
inside the cabinet.
2. Make sure that indicator (D) is in “1” position.
3. Turn on dishwasher if it is off – press main
switch (C) to “on” position (LED’s are lighting).
4. Press TEST button (E). Indicator should switch
into “0” position. If it does not dishwasher can
not be used – contact service immediately.
5. Switch back indicator into “1” position.
6. Place GFCI cover and screw down two bolts.
Check operation
• Refer to the “Instruction For Use” booklet that
came with this dishwasher and run the
dishwasher through a complete cycle.
• Check for leaks.
5019 102 00395
Printed in Italy
n
06/08
GB
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

KitchenAid KDIX 8810 Installation guide

KDIX 8810
KitchenAid
Brand
KitchenAid
Model
KDIX 8810
Category
Sanitary ware
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents