KitchenAid KIDS36 User manual

Brand: KitchenAid

Model: KIDS36

Type: User manual

This manual is also suitable for

KIDS42

Page is loading ...

DISHWASHER SAFETY

TABLE OF CONTENTS

DISHWASHER SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

INSTALLATION REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . .3

Tools and Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Location Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Drain Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Water SupplyRequirements . . . . . . . . . . . . . . . . . . . . . . . . .6

Electrical Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

INSTALLATION INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . .7

Prepare Dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Install Dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Make Electrical Connection . . . . . . . . . . . . . . . . . . . . . . . . .7

Connect Water Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Complete Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

■ This dishwasher is manufactured for indoor use only.

■ Observe all governing codes and ordinances.

■ Install this dishwasher as specified in these instructions.

■ Installation should be performed by a qualified service

technician. The dishwasher must be installed to meet all

electrical and plumbing national and local codes and

ordinances.

Tools and Parts

Gather the required tools and parts before starting installation.

Read and follow the safety instructions provided with any tools

listed here. Additional tools may be required to cut contertop and

install drain lines.

Tools needed:

■ Utility knife

■ 5/8" open-end wrench

■ 7/16" deep well socket

■ small tubing cutter

■ tape measure

■ flat bladed screwdriver

■ plumber’s putty

■ 10" adjustable wrench that opens to 1-1/8" (2.9 cm)

■ Teflon

tape or pipe joint compound

■ 1 cartridge silicone caulk and caulk gun

■ sink strainer locknut wrench

Parts needed:

■ Copper tubing with compression fitting for water fill line (3/8"

is recommended). Length needed is determined by specific

installation requirements.

■ Copper tubing with compression fittings for faucet connection.

Length and diameter needed are determined by specific

faucet installation requirements.

■ faucet

■ 2, 1-1/2" drain P traps

■ 3-1/2" sink strainer

■ 90° elbow with 3/8" N.P.T. external threads on one end.

(The other end must fit your water supply line.)

In addition, if direct wiring:

■ 1/4" hex nut driver

■ 2, twist-on connectors of proper size to connect house wiring

to 16-gauge dishwasher wiring.

■ CSA-certified, U.L.- or C.-U.L. listed conduit connector to fit

7/8" (2.2 cm) hole

Parts supplied:

■ Undercounter clamp brackets – adjustable for countertops

3/4" (1.9 cm) to 1-1/2" (3.8 cm) thick

■ cutting board

INSTALLATION REQUIREMENTS

Location Requirements

Protect dishwasher and water lines leading to dishwasher against

freezing. Damage from freezing is not covered by the warranty.

If dishwasher will be left unused for a period of time or in a

location where it may be subject to freezing, have it winterized by

authorized service personnel.

The dishwasher is shipped ready for installation of a one-hole

faucet. If a two-, three-, or four-hole faucet is to be installed, the

holes must be added by a qualified plumber, according to the

faucet manufacturer’s specifications.

If the hot water accessory tank, Part No. 4396282 will be used,

the tank should be installed first. It may be difficult to install the

drain line to the T&P valve on the hot water accessory tank, if it is

not installed first.

Back right corner: If countertop is

more than 3/4" (1.9 cm) thick,

measure down 3/4" (1.9 cm) and cut

45° bevel all the way around radius.

19-3/8"

(49.2 cm)

maximum

opened lid

height

20-21/32" (52.5 cm)

9-7/16"

(24.0 cm)

1-3/4" (4.4 cm)

to center of single

hole faucet

factory

installed air

gaps

dishwasher

drain

water inlet

valve

(between clamp rails)

22" (55.9 cm)

(between clamp rails)

5-25/32"

(14.7 cm)

39-11/16" (100.8 cm)

14" (35.6 cm)

18-5/16" (46.5 cm)

22-1/32"

(56.0 cm)

21"

(53.3 cm)

1-1/4"

(3.2 cm)

(20.3 cm)

9-9/16"

(24.3 cm)

center of

sink drain

5-1/2 ft. (1.7 m)

3-prong ground-type

power supply cord

16-7/8" (42.9 cm)

to center of single

hole faucet

*NOTE: The cutout must be accurately cut to the dimensions shown within

1/16" (1.6 mm). Dishwasher top flange overlaps the countertop cutout

by 7/16" (1.1 cm) on front and back edges and 1/4" (6.4 mm) on sides.

• Cabinetry and countertop must be sturdy enough to support loaded

dishwasher and sink (400 lbs. [181.4 kg]).

IMPORTANT: Corner radius dimensions

specified must be used. If they are not,

the dishwasher will not fit the opening.

radius: 2-1/4" (5.7 cm)

3/4"

(1.9 cm)

45°

for base cabinet

installations, min. 42"

(106.7 cm) width required

21-1/8"

(53.7 cm)

(see *NOTE)

40" (101.6 cm)

(see *NOTE)

It is recommended that sink

water and drain line

connections be located on

this side of cabinet.

It is recommended

that dishwasher water

and drain line

connections be

located on this side

of cabinet.

21-1/8"

(53.7 cm)

(see *NOTE)

backsplash

CRITICAL

RADIUS

radius: 1" (2.5 cm) – the

right back corner must be

cut to this radius

GFCI reset

buttons

25" (63.5 cm) deep

countertop

Countertop must be

level.

SIDE FRONT

40-1/2" (102.9 cm)

7/16" (1.1 cm) min.

flat surface required

KIDS42 Product dimensions

KIDS42 Cabinet requirements

Back right corner: If countertop is

more than 3/4" (1.9 cm) thick,

measure down 3/4" (1.9 cm) and cut

45° bevel all the way around radius.

19-3/8"

(49.2 cm)

maximum

opened lid

height

20-21/32" (52.5 cm)

9-7/16"

(24.0 cm)

1-3/4" (4.4 cm)

to center of single

hole faucet

factory

installed air

gaps

dishwasher

drain

water inlet

valve

(between clamp rails)

22" (55.9 cm)

(between clamp rails)

5-25/32"

(14.7 cm)

33-11/16" (85.6 cm)

14" (35.6 cm)

18-5/16" (46.5 cm)

22-1/32"

(56.0 cm)

21"

(53.3 cm)

1-1/4"

(3.2 cm)

(20.3 cm)

6-9/16"

(16.6 cm)

center of

sink drain

5-1/2 ft. (1.7 m)

3-prong ground-type

power supply cord

10-7/8" (27.5 cm)

to center of single

hole faucet

*NOTE: The cutout must be accurately cut to the dimensions shown within

1/16" (1.6 mm). Dishwasher top flange overlaps the countertop cutout

by 7/16" (1.1 cm) on front and back edges and 1/4" (6.4 mm) on sides.

• Cabinetry and countertop must be sturdy enough to support loaded

dishwasher and sink (400 lbs. [181.4 kg]).

IMPORTANT: Corner radius dimensions

specified must be used. If they are not,

the dishwasher will not fit the opening.

radius: 2-1/4" (5.7 cm)

3/4"

(1.9 cm)

45°

for base cabinet

installations, min. 36"

(91.4 cm) width required

21-1/8"

(53.7 cm)

(see *NOTE)

34" (86.4 cm)

(see *NOTE)

It is recommended that sink

water and drain line

connections be located on

this side of cabinet.

It is recommended

that dishwasher water

and drain line

connections be

located on this side

of cabinet.

21-1/8"

(53.7 cm)

(see *NOTE)

backsplash

CRITICAL

RADIUS

radius: 1" (2.5 cm) – the

right back corner must be

cut to this radius

GFCI reset

buttons

25" (63.5 cm) deep

countertop

Countertop must be

level.

SIDE FRONT

34-1/2" (87.6 cm)

7/16" (1.1 cm) min.

flat surface required

KIDS36 Product dimensions

KIDS36 Cabinet requirements

Drain Requirements

Separate drain P-traps for the sink and dishwasher must be

provided.

Dishwasher drain:

If the dishwasher drain exits through the back wall, the centerline

of the drain pipe must be a minimum of 1/2" (1.3 cm) below the

dishwasher drain. This is required to completely drain the

dishwasher tub so that no standing water remains in tub.

Water Supply Requirements

For dishwasher:

■ Hot water line with 20-120 psi (138-827 kPa) water pressure.

120°F (49°C) water at dishwasher.

■ Copper tubing with compression fitting. 3/8" O.D. is

recommended.

■ A 90° elbow with 3/8" N.P.T. external pipe threads on one end.

IMPORTANT: Do not solder within 6" (15.2 cm) from water inlet

valve.

For sink faucet:

■ Hot and cold water line.

■ Copper tubing with compression fittings for specific faucet to

be installed.

Electrical Requirements

■ If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the

ground path is adequate.

■ Do not ground to a gas pipe.

22-1/32"

(56.0 cm)

to bottom of

dishwasher drain

1/2" (1.3 cm)

minimum

back wall

■ Check with a qualified electrician if you are not sure the

dishwasher is properly grounded.

■ Do not have a fuse in the neutral or ground circuit.

■ A 120-volt, 60 Hz, AC-only, 15 or 20 amp fused electrical

supply is required. (Circuit breaker or time-delay fuse is

recommended.) It is recommended that a separate circuit

serving only this appliance be provided.

Hot Water Accessory Tank

If you plan to install the Hot Water Accessory Tank Part

No. 4396282, an additional separate120-volt, 60 Hz, AC-only, 15

or 20 amp fused electrical supply is required.

Garbage Disposer

If you plan to install a garbage disposer, an additional separate

120-volt, 60 Hz, AC-only, 15 or 20 amp fused electrical supply is

required.

Recommended ground method

For your personal safety, this appliance must be grounded. This

appliance is equipped with a power supply cord having a 3 prong

ground plug. To minimize possible shock hazard, the cord must

be plugged into a mating 3 prong ground-type outlet, grounded in

accordance with local codes and ordinances.

If a mating outlet is not available, it is the personal responsibility

and obligation of the customer to have a properly grounded

3 prong outlet installed by a qualified electrician.

If dishwasher must be direct wired

■ Use flexible, armored or non-metallic sheathed, copper wire

with grounding wire that meets the wiring requirements for

your home and local codes and ordinances.

■ Use a CSA-certified, U.L.- or C-U.L.-listed conduit connector

or if using non-metallic sheathed, copper wire, a CSA-

certified, U.L.- or C-U.L.-listed cable clamp connector.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

Electrical Shock Hazard

Electrically ground dishwasher.

Connect ground wire to green ground connector in

terminal box.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

INSTALLATION INSTRUCTIONS

Prepare Dishwasher

IMPORTANT: If hot water accessory tank (accessory Part

No. 4396282) will be used, the tank must be installed first.

1. With a utility knife, cut along the back right corner of inner

carton.

2. Remove inner carton. Leave dishwasher on bottom pad.

3. Install faucet (not included). The dishwasher is shipped ready

for installation of a one-hole faucet. If a two-, three- or four-

hole faucet is to be installed, the holes must be added by a

qualified plumber according to the faucet manufacturer's

specifications.

Install Dishwasher

1. Mark countertop and apply a 1/4" (6.4 mm) bead of silicone

caulk 1/4" (6.4 mm) away from dishwasher cutout on sides

and 7/16" (1.1 cm) on front and back.

2. Set the dishwasher into countertop cutout. Make sure front of

dishwasher is parallel to front edge of countertop.

IMPORTANT: To prevent damage to

right-hand hinge, open dishwasher lid

before setting dishwasher into

countertop cutout.

3. Immediately remove any excess caulking.

back of

inner carton

cut along

this corner

1/4" (6.4 mm)

bead of silicone

caulk

dishwasher

cutout

WARNING

Excessive Weight Hazard

Use two or more people to move and install dishwasher.

Failure to do so can result in back or other injury.

4. Install two clamp brackets, evenly spaced, on front, back and

left (sink) side clamp rails. Optional: If space permits, install

two clamp brackets, evenly spaced, on the right side rail.

To install clamps:

■ Hook upper clamp onto rail. Use flat-blade screwdriver to

attach clamp to rail.

■ Use 7/16" deep-well socket and securely tighten nut

against lower clamp. Do not overtighten.

Make Electrical Connection

If you are:

■ direct wiring, use Option 1

■ using a power supply cord, use Option 2

Option 1, Direct wired method

If dishwasher must be directly wired to meet local codes, the

power supply cord must be removed and dishwasher wired

directly. Electrical connections must be contained within the

terminal box and meet all national and local codes and

ordinances.

Route direct wire so that it does not touch lower part of

dishwasher tub to prevent undue sound and vibration.

If power supply cord is removed, the dishwasher must be

connected with copper wire only.

1. Disconnect power.

rail

upper clamp

lower clamp

countertop

WARNING

Electrical Shock Hazard

Disconnect electrical power at the fuse box or circuit

breaker box before installing dishwasher.

Failure to do so can result in death or electrical shock.

10. Route direct wire through conduit and connect wires as

follows:

■ Form ground wire into a hook and wrap clockwise around

ground screw under washer. Tighten ground screw

securely.

■ Use twist-on connectors of proper size to connect direct

wire to 16-gauge wire dishwasher wiring. Connect black

wires together and white wires together.

11. Reinstall terminal box.

IMPORTANT: The tabs must be under the terminal box as

shown.

2. Remove 5 screws (2 each side and above GFCI) holding the

metal front panel and remove panel.

3. Remove terminal box screw and terminal box.

4. Remove power cord green ground wire from under green

ground screw.

5. Remove twist-on connectors and disconnect black and white

wires. Do not reuse connectors.

6. Use pliers and squeeze locking tab in the power cord strain

relief grommet.

7. Remove power cord and grommet.

8. Install a CSA-certified, U.L.- or C-U.L.-listed conduit

connector in power cord hole.

9. Install conduit.

screws

GFCI

front panel

green ground wire

do not remove this

grommet

power cord

conduit

connector

terminal box

screw

terminal

box

green ground screw

power cord

locking tab

WARNING

Electrical Shock Hazard

Electrically ground dishwasher.

Connect ground wire to green ground connector in

terminal box.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

green ground

screw

ground wire

direct wire

tabs

terminal box

Complete Installation

Power supply cord method

Direct wire method

1. Plug in dishwasher or reconnect power.

IMPORTANT: The following steps must be done before using

the dishwasher, to test and activate the GFCI.

2. Press the reset button on the GFCI. The indicator should be

visible.

3. Press the test button on the GFCI. The indicator should

disappear.

4. Press the reset button. The indicator should reappear.

If the GFCI fails this test, do not use the dishwasher. Call

the KitchenAid Customer Interaction Center toll-free at

1-800-422-1230 or in Canada, 1-800-461-5681, for

assistance.

reset

test

indicator

WARNING

Electrical Shock Hazard

Electrically ground dishwasher.

Connect ground wire to green ground connector in

terminal box.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Option 2, Power supply cord method

1. Plug into a grounded 3 prong outlet.

Connect Water Supply

1. Apply Teflon

tape or pipe joint compound to 90° elbow fitting

and connect fitting to water inlet valve.

2. Use adjustable wrench and tighten elbow until snug and

facing the direction needed for your water fill line installation.

IMPORTANT: If you are installing the Hot Water Accessory

Tank, go back to its Installation Instructions and complete that

installation at this time.

3. Connect the dishwasher water fill line.

a. Slide nut onto copper tubing about 1" (2.5 cm).

b. Slide ferrule onto the tubing. Do not position ferrule on the

end of the tubing.

c. Put the tubing into the elbow as far as it will go.

d. Slide the nut and ferrule forward and start the nut onto the

elbow threads. Be gentle when handling and positioning

the copper tubing, it bends and kinks easily.

e. With copper tubing pushed into elbow as far as it will go,

use a 5/8" open-end wrench and tighten the compression

nut securely.

4. Connect hot and cold water lines to faucet.

5. Connect the sink and dishwasher drain plumbing.

6. Turn water supply on to both dishwasher and sink faucet.

Check for leaks.

water fill line

connection

do not apply Teflon

tape

or pipe joint compound

apply Teflon

tape or

pipe joint compound

water inlet

valve

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

8564766

® Registered Trademark/™ Trademark of KitchenAid, U.S.A.; KitchenAid Canada Licensee in Canada.

® Teflon is a registered trademark of E.I. Du Pont de Nemours and Company.

Printed in U.S.A.

09/2004

Check operation

1. Refer to the Use and Care Guide that came with this

dishwasher and run the dishwasher through a complete cycle.

2. If Hot Water Accessory Tank is installed, wait about 45

minutes before starting the next dishwasher cycle to allow the

hot water tank to finish heating. (Refer to the Installation

Instructions and Use and Care Guide supplied with the Hot

Water Accessory Tank.)

3. When the hot water tank is first heated, it is normal for a small

amount of water to be discharged into the dishwasher.

4. Check for leaks.

Page is loading ...

KitchenAid KIDS36 User manual

Brand: KitchenAid

Model: KIDS36

Type: User manual

This manual is also suitable for

KIDS42

Download PDF

report

in other languages

français: KitchenAid KIDS36 Manuel utilisateur
español: KitchenAid KIDS36 Manual de usuario

KitchenAid KIDS36 User manual

This manual is also suitable for

KitchenAid KIDS36 User manual

in other languages

Related papers

Other documents