1300PSI
Owner’s Manual
Problems?
Questions?
Before taking your unit
back to the store,
call the pressure washer
helpline at
1-800-270-1408
M-F 8-5 CST
GENERAC
The Reliable Ones
This symbol points out important safety instructions, which, if not followed, could
endanger the personal safety and/or property of yourself and others. Read and follow all
instructions in the manual before attempting to operate this unit.
Model No. 12800 (1300 PSI High Pressure Washer) Manual No. B3719 Revision 0 (1/27/99)
Generac 1300PSI High Pressure Washer
GENERAC
The Reliable Ones
2
CAUTION! Read all instructions before using
this product to reduce the risk of injury.
DANGER! Risk of electrocution!
Inspect cord before every use. Do not use if cord is
damaged.
Keep all connections dry and off the ground.
Do not touch plug with wet hands.
Doubleinsulated When servicing, use only
identical replacement parts.
This product shall only be connected to a power
supply receptacle protected by a Ground Fault
Circuit Interrupter (GFCI).
Read instruction manual before using.
WARNING! To reduce the risk of injury, close
supervision is necessary when product is used
near children.
Know how to stop the product and bleed the
pressure quickly. Be thoroughly familiar with
controls.
Stay alert. Watch what you are doing.
Do not operate the product when fatigued or under
the influence of alcohol or drugs.
Keep operating area clear of all persons.
WARNING! Risk of injury or injection to
persons Do not discharge stream at persons
or animals.
High pressure hose can develop leaks from wear,
kinking, abuse, etc. Water spraying from a leak is
capable of injecting material into skin. Do not point
the pressure washer spray at people or animals.
Do not overreach or stand on unstable support.
Keep good footing and balance at all times.
Follow the maintenance instructions specified in the
manual.
This product shall only be connected to a power
supply receptacle protected by a Ground Fault
Circuit Interrupter (GFCI). This is done to comply
with National Electrical Code (NFPA 70) and to
provide additional protection from risk of electrical
shock.
Save these instructions.
Operate this pressure washer only in areas away
from combustible materials, combustible fumes or
dust.
Some chemicals or detergents may be harmful if
inhaled or ingested, causing severe nausea,
fainting or poisoning. The harmful elements may
cause property damage or severe injury.
Do not allow CHILDREN to operate the Pressure
Washer at any time.
Before starting the Pressure Washer in cold
weather, check all parts of the equipment and be
sure ice has not formed.
Units with broken or missing parts, or without
protective housing or covers should NEVER be
operated.
DANGER! Risk of Explosion Do not spray
flammable liquids.
Never aim the gun at people, animals or plants.
For household use. For indoor or outdoor use.
High pressure stream of fluid that this equipment
can produce may pierce skin and its underlying
tissues, leading to serious injury and possible
amputation.
High pressure spray can cause paint chips or other
particles to become airborne and fly at high speeds.
Save these instructions
Important! Safety Instructions Important!
Generac 1300PSI High Pressure Washer
GENERAC
The Reliable Ones
3
Always wear eye protection when you use this
equipment or when you are in vicinity where the
equipment is in use.
Never move the machine by pulling on high
pressure hose. Use the handle provided on the top
of the unit.
Use a respirator or mask whenever there is a
chance that vapors may be inhaled. Read all
instructions with the mask so you are certain the
mask will provide the necessary protection against
inhaling harmful vapors.
High pressure spray may damage fragile items
including glass. Do not point spray gun at glass
when in the high pressure mode.
Keep the hose connected to machine or the spray
gun while the system is pressurized. Disconnecting
the hose while the unit is pressurized is dangerous.
Hold the spray gun firmly in your hand before you
start the unit. Do not leave the pressure washer
unattended while the machine is turned on.
Cleaning area should have adequate slopes and
drainage to reduce possibility of a fall due to
slippery surfaces.
Keep water spray away from electric wiring or fatal
electric shock may result.
Do not bypass any safety device on this machine.
Operate and store this unit on a stable surface.
Inspect hose each time before using it. Check all
hoses for cuts, leaks, abrasions, bulging of cover,
damage or movement of couplings. If any of these
conditions exist, replace hose immediately. Never
repair high pressure hose. Replace it with another
hose that meets minimum pressure rating of your
pressure washer.
Store in a clean, dry area. Ideally, the unit should be
stored in a frostfree room.
Servicing of a Double Insulated Product.
In a doubleinsulated product, two systems of
insulation are provided instead of grounding. No
means of grounding is provided on a
doubleinsulated product, nor should a means for
grounding be added.
Servicing a doubleinsulated product requires
extreme care and knowledge of the system and
should be done only by qualified service personnel.
Replacement parts for a doubleinsulated product
must be identical to the parts they replace. Use only
genuine replacement parts. A doubleinsulated
product is marked with the words DOUBLE
INSULATION or DOUBLE INSULATED.
The symbol may also be marked on the product.
Extension Cords
Use only extension cords that are approved for
outside use. These extension cords are identified by
a marking ACCEPTABLE FOR USE WITH
OUTDOOR APPLIANCES; STORE INDOORS
WHILE NOT IN USE. Use only extension cords
having an electrical rating greater than the rating of
the product. Do not use damaged extension cords.
Examine extension cord before using and replace if
damaged. Do not abuse extension cord and do not
yank on any cord to disconnect it. Keep cord away
from heat and sharp edges. Always disconnect the
extension cord from the receptacle before
disconnecting the pressure washer from the
extension cord.
Save these instructions
Important! Safety Instructions Important!
Generac 1300PSI High Pressure Washer
GENERAC
The Reliable Ones
4
CONGRATULATIONS on your purchase of a
GENERAC electric high pressure washer. It has been
designed, engineered and manufactured to give you
the best possible dependability and performance.
Should you experience any problem you cannot easily
remedy, please contact your nearest GENERAC
Authorized Service facility, or call 18002701408.
We have competent, welltrained technicians and the
proper tools to service or repair this unit.
Please read and retain this manual. The instructions
will enable you to assemble and maintain your high
pressure washer properly. Always observe the
SAFETY INSTRUCTIONS.
CUSTOMER
RESPONSIBILITIES
Read and observe the safety rules.
Follow regular schedule in maintaining, caring for
and using your high pressure washer.
Follow the instructions under Maintenance and
Storage sections of this Owner's Manual.
PRODUCT
SPECIFICATIONS
Pressure Washer Specifications
Pressure 1300 pounds per square inch
(PSI)
Flow Rate 1.5 gallons per minute (GPM)
Detergent Mix Use Undiluted Detergent
Water Supply Inlet water not to exceed
Temperature 104°F
Motor Brush Type (Universal)
Rated Voltage 120 Volts
Current 14 Amperes
Read these instructions and Operators Manual in its
entirety before you attempt to assemble or operate
your new high pressure washer. Your high pressure
washer has, for the most part, been assembled at the
factory. Before you can operate your new high
pressure washer, you must properly connect the high
pressure hose and the water supply.
If you have any problems with the assembly of your
pressure washer, please call the pressure washer
helpline at 18002701408.
Model
Number 12800
Serial
Number_________________________________
Date of
Purchase________________________________
The model and serial numbers will be found on a
decal attached to the pressure washer. Record
both serial number and date of purchase and keep
in a safe place for future reference
KNOW YOUR PRESSURE WASHER
Read this owners manual and safety rules before operating your high pressure washer. Compare the
illustrations with your high pressure washer to familiarize yourself with the locations of various controls and
adjustments. Save this manual for future reference.
Generac 1300PSI High Pressure Washer
GENERAC
The Reliable Ones
5
Foamer Used to apply detergent. Mixes water
and detergent in outlet water flow.
Garden Hose Connector (Not Shown) Allows
rapid connection of your garden hose to the water
inlet.
Goggles Always wear eye protection when
operating your pressure washer.
Grip Start System Pressing and releasing the
spray gun trigger starts and stops the electric motor in
the pressure washer.
High Pressure Hose Connect ends to spray gun
and high pressure outlet.
High Pressure Outlet Connection for high
pressure hose.
Master On/Off Switch This switch ONLY enables
the Grip Start system to function.
Spray Gun Controls the application of water onto
cleaning surface with trigger device. Includes safety
latch.
Turbo Nozzle and Extension Attaches to the
spray gun and allows you to clean or rinse surfaces at
high pressure. You cannot apply detergent using the
turbo nozzle.
Water Inlet Connection for garden hose.
Spray Gun
Master On/Off Switch
High Pressure Outlet
High Pressure
Hose
Turbo Nozzle and
Extension
Water Inlet
Grip Start
System
Foamer
Goggles
Generac 1300PSI High Pressure Washer
GENERAC
The Reliable Ones
6
CARTON CONTENTS
Items in the carton include:
Main Unit
Parts Box (which includes the following):
Goggles
Owners Manual
Spray Gun
Turbo Nozzle and Extension
Foamer
High Pressure Hose
Garden Hose Connector
Refer to the above list for an illustrated listing of all
items included with your pressure washer. Become
familiar with each piece before assembling the
pressure washer. Check all contents against list. If
any parts are missing, call the pressure washer
helpline at 18002701408.
HOW TO SET UP YOUR
PRESSURE WASHER
Unwind the high pressure hose and attach it to
spray gun (Figure 1).
Attach the high pressure hose to the high pressure
outlet and tighten by hand (Figure 2).
Check the screen on the garden hose connector.
Make sure it is clean and check for damage. If you
see any damage in the screen, do not use
(Figure 3).
Attach the garden hose connector to the pressure
washer.
Attach garden hose to the pressure washer.
DANGER! When connecting the unit to a
power supply receptacle, use ONLY a
receptacle protected by a Ground Fault Circuit
Interrupter (GFCI). This will help protect
against electrical shock.
Figure 2 Attach High Pressure Hose to Main
Unit.
Figure 1 Attach High Pressure Hose to Spray
Gun.
Connect high pressure
hose here
Figure 3 Install Garden Hose Connector and
Attach Garden Hose.
Check inlet screen.
Connect garden hose
here.
Generac 1300PSI High Pressure Washer
GENERAC
The Reliable Ones
7
CAUTION! Before starting you should be
sure the electrical supply is rated at 120 volts,
15 amps.
WARNING! To reduce the risk of
electrocution, keep ALL connections dry and
off the ground. DO NOT touch plug with wet
hands.
Note: We do not recommend that you use extension
cords with this pressure washer. If, however, your
application requires that you need an extension cord,
use only extension cords that are approved for
outside use. These extension cords are identified by a
marking ACCEPTABLE FOR USE WITH OUTDOOR
APPLIANCES; STORE INDOORS WHILE NOT IN
USE. Use only extension cords having an electrical
rating not less than the rating of the product. Do not
use damaged extension cords.
DANGER! You must attach the spray gun
and all hoses before you start the motor.
Turn on the water.
NOTE: Inlet water temperature should not exceed
104°F.
DANGER! You must be careful at this point.
Anytime you squeeze the trigger, the motor will
start and water will spray out of the gun.
Squeeze trigger to purge pump of system air and
impurities.
Attach the turbo nozzle extension to spray gun by
aligning the locking tabs on the extension with the
grooves in the gun. Push extension inward and twist
clockwise to lock in place (Figure 4).
Press the master On/Off Switch to the On position
(Figure 5).
WARNING! Before starting the pressure
washer, be sure you are wearing adequate eye
protection. Goggles are included with this unit.
WARNING! Gun kicks back. Use both
hands.
DANGER! Risk of injury or injection to
people and animals. DO NOT discharge
stream at people or animals.
Squeeze trigger to produce spray.
NOTE: Behind the trigger to the gun is a SAFETY
LATCH. You can place this latch as shown (Figure 6)
to keep the washer from accidentally spraying while
you are changing the nozzle head or foamer or
performing other tasks.
Figure 5 Press the Master On/Off Switch to
the On Position.
Figure 4 Connect the Turbo Nozzle Extension
to the Spray Gun.
Figure 6 Apply the Safety Latch.
Generac 1300PSI High Pressure Washer
GENERAC
The Reliable Ones
8
STOPPING YOUR
PRESSURE WASHER
If the pressure washer is running, release the
trigger.
DANGER! Releasing the trigger will shut off
the motor but does not shut off the unit. You
must also place the Master On/Off Switch to
the OFF position.
Place Master On/Off switch in Off position.
Simply shutting OFF motor will not release
pressure in the system. Squeeze the trigger on the
gun to relieve the pressure in the hose.
DANGER: Never leave your pressure
washer unattended even when turned off.
HOW TO USE YOUR
WASHER
You now should know how to START your pressure
washer and how to STOP it. The information in this
section will tell you how to adjust the spray pattern
and apply detergent or any other cleaning chemicals.
How to Use the Turbo Nozzle
The turbo nozzle rotates the high pressure stream in
a rapid circular pattern. The high pressure spray is
most effective when the tip of the wand is held
between 8 to 24 inches from the surface being
cleaned.
Always start the turbo nozzle at a distance, gradually
getting closer to the surface until you get the cleaning
force you want.
CAUTION! The turbo nozzle produces an
extremely high pressure spray which is
capable of removing paint and cutting holes
through surfaces if held too close. Always
make sure the surface you will clean will not
be damaged by the high pressure spray by
testing in a hidden area.
Note: You cannot apply detergent with the turbo
nozzle.
Applying Detergent With Foamer
IMPORTANT: Use soaps designed specifically for
pressure washers. Household detergents could
damage the pump.
NOTE: Never use garden hose inlet to siphon
detergent or wax.
DANGER: You MUST attach all hoses and the spray
gun before you start the motor.
WARNING! Before removing any spray gun
extension, be sure to turn off the pressure
washer and relieve pressure by pressing the
trigger. You could be injured if you try to
remove an extension if the pressure washer is
running and there is pressure in the system.
Pressure washers are useful cleaning tools designed
to clean almost any surface in two easy steps.
First, apply an appropriate detergent/solvent
solution to penetrate and loosen grime. Apply
detergent at low pressure to avoid splashing,
overspraying and waste. Leave the solution on
surface for 3 to 5 minutes to allow solution to work.
Reapply as necessary to keep solution from drying.
The second step involves cleaning the surface you
have prepared with the pressure washer and then
rinsing it clean.
Generac 1300PSI High Pressure Washer
GENERAC
The Reliable Ones
9
To apply detergent follow these steps:
Detach the turbo nozzle extension from the spray
gun.
Remove the bottle from the foamer.
Align the locking tabs on the foamer with the groves
in the gun. Push inward and twist clockwise to lock
in place. (Note: make sure that when you lock the
foamer into place you have the hose that connects
to the foamer bottle hanging downward.)
Prepare your detergent solution as required by the
manufacturer and fill bottle with the solution.
Attach bottle back onto foamer making sure the
bottle hangs down.
Start washer and apply detergent to a dry surface,
starting from the bottom and working up.
To rinse, YOU MUST, stop the pressure washer,
remove the foamer and connect the adjustable
nozzle extension.
Note Detergents are most effective applied to a dry
surface.
To Clean
Start at lower portion of area to be washed and work
upward, using long, even overlapping strokes.
Detergent or degreaser works best when you apply it
to a dry surface first. Let it set for 35 minutes before
washing and rinsing.
Rinse
Start at the top of area to be rinsed, working down
with the same action as for cleaning.
Figure 9 Connecting the Foamer.
Generac 1300PSI High Pressure Washer
GENERAC
The Reliable Ones
10
CUSTOMER
RESPONSIBILITIES AND
MAINTENANCE
The warranty of the high pressure washer does not
cover items that have been subjected to operator
abuse or negligence. To receive full value from the
warranty, operator must maintain high pressure
washer as instructed in this manual.
BEFORE EACH USE
Check and Clean Inlet Screen
Remove garden hose connector and examine the
inlet screen. Clean if clogged or replace the inlet
screen if damaged.
Check High Pressure Hose
DANGER: Water spraying from a leak is
capable of injecting material into skin. Inspect
hose each time before using it. Never repair
high pressure hose. Replace it with another
hose that meets minimum pressure rating of
your pressure washer.
High pressure hose can develop leaks from wear,
kinking, and abuse. Check all hoses for cuts, leaks,
abrasions or bulging of cover, or damage or
movement of couplings. If any of these conditions
exist, replace hose immediately.
Check Gun and Wand
Examine hose connection and make sure it is secure.
Test trigger by pressing it and making sure it springs
back into place when released. Put safety latch in ON
position and test trigger. You should not be able to
press trigger.
PURGE PUMP OF AIR AND
CONTAMINANTS
To remove the air from the pump, follow these
steps:
Set up the pressure washer as described in the
ASSEMBLY section and connect the water supply.
Remove the turbo nozzle extension from the gun.
Pull the trigger on the gun and hold.
To remove the contaminant from the pump, follow
these steps:
Set up the pressure washer as described in the
ASSEMBLY section, connect the water supply and
start the pressure washer according to instructions
in the OPERATION section.
Remove the turbo nozzle extension from the gun.
Pull the trigger on the gun and hold.
When the water supply is steady and constant, you
may refasten the turbo nozzle extension and use
pressure washer normally.
PREPARING THE UNIT FOR
STORAGE
Water should not remain in the unit for long periods of
time. Sediments of minerals can deposit on pump
parts and freeze pump action. If you do not plan to
use the Pressure Washer for more than 30 days,
follow this procedure:
1. Shut off the pressure washer, unplug it and let it
cool, then remove all hoses.
2. Store the pressure washer and its components in
such a way as to protect it from freezing.
5. Store in a clean, dry area. Ideally, the unit should
be stored in a frostfree room.
6. Coil the high pressure hose and inspect it for
damage. Cuts in the hose or fraying of it could result
in leaks and loss of pressure. Should any damage be
found, replace the hose. DO NOT attempt to repair a
damaged hose. Replace the hose with the genuine
Generac part.
7. Drain water from hose and properly store it to
prevent cuts and general wear.
Troubleshooting Points
Generac 1300PSI High Pressure Washer
GENERAC
The Reliable Ones
11
Problem Cause Correction
Pressure washer will not start. 1. No electrical power is available. 1. Check cord, plug power, socket,
electrical supply and circuit
breaker/fuse.
2. Motor overheats. 2. Turn off the unit. Press trigger of
gun to relieve pressure on the
unit. Allow unit to cool for about 2
min. It should run when you turn it
ON again.
3. Low voltage. 3. Contact Generac service facility.
4. Trigger not open. 4. Open trigger.
5. Electrical defect. 5. Contact Generac service facility.
Pressure washer does not 1. Pump is sucking air. 1. Water hose must be 1/2inch
come up to pressure. or greater in diameter.
Be sure water supply is ON.
Be sure water supply is clean.
Check all connections for leaks
or blockage.
Turn OFF the unit, hold trigger in
OPEN position to relieve pressure
and allow air in line to escape.
With trigger still in OPEN position
turn ON the unit. Repeat if
necessary.
2. Water inlet is clogged. 2. Clean water inlet screen.
3. Pump not bled to remove air. 3. Switch OFF washer, press trigger,
switch ON washer while pressing
trigger. Repeat if necessary.
4. Pump is faulty. 4. Contact Generac service facility.
High pressure spray is irregular. 1. Water supply is inadequate. 1. Turn ON water to full position.
12
Generac 1300PSI High Pressure Washer
GENERAC
The Reliable Ones
Drawing No. B3653
Exploded View Pump and Motor
13
Generac 1300PSI High Pressure Washer
GENERAC
The Reliable Ones
Parts List Pump and Motor
Item Part # Qty Description
1 B1514 1 ASSY, Motor Complete
2 40945 3 BOLT, SHCS M6-1.0 x 20mm
3 97835 1 O RING, Hsg Seal, dia. 82.2
x 2.62mm
4 20610 2 WASHER, Brg dia. 35 x 55 x
3mm
5 97822 1 BEARING, Ndle Thrust dia. 35
x 52mm
6 B2663 1 ASSY., Cam/Gear
7 97826 1 WASHER, Brg dia. 40 x 60 x
1mm
8 97824A 1 BEARING, Needle dia. 40 x
60mm
9 97825 1 WASHER, Brg dia. 36 x 60 x
6mm
10 97833 1 SHAFT, Idler Axial Cam
11 97830 3 RETAINER, Piston Spring
12 97832 3 PISTON, dia. 15 x 65mm
13 99503 3 SPRING, Piston Return
14 A1495 2 TAPTITE, M4-0.7x10mm SW
MTG
15 21055 1 GROMMET, Rubber
16 28739A 1 TIE, Wrap
17 20138 1 SWITCH, Auto
18 20928 1 HOUSING, Auto-Switch
19 B3660 1 SPRING, P.A.S.S.
20 B3568 1 PISTON ASSY, P.A.S.S.
21 21126 1 RING, Backup dia. 26.0 ID
22 21125 1 O RING dia. 25.07 ID x 2.62
CS [.103"]
23 20217 1 STOP, Piston Return
Item Part # Qty Description
24 21124 1 RING, Backup dia. 4.34 Id x
1.24
25 20218 1 CAP, Retainer
26 21123 1 O RING dia. 3.68 Id x 1.78
CS [.070"]
27 B1124 1 CAP, Inlet
28 97855 1 O RING, dia. 6.5 x 2.01mm
29 97100 1 CAP, High Pressure
30 B3570 1 HOUSING, Piston
31 93680 3 SEAL, Oil-piston dia. 15 TC4
32 97831 3 SPACER, Pilot
33 97929 1 SPRING, Check Valve
34 B3569 1 VALVE, Shuttle
37 97841 3 CAP, Check Valve
38 97840 3 O RING, Hi-press dia. 15.6 x
1.78mm
39 B1449 6 ASSY., Check Valve
40 97934 7 O RING, Chk Valve dia. 12.4
x .78mm
41 76353A 1 PLUG, Taper dia. 5.4
42 97852 1 BALL, dia. 3/16" Pop-off Valve
43 B2240 1 SCREW, Lock Socket
44 A1130 1 SPRING, Pop-off Valve
45 B1960 1 SEAT, Ball
46 40946 4 BOLT, SHCS M6- 1.0 x 35mm
48 B3571 1 PUMP, Head
49 93667 3 SEAL, Piston U Cup
50 B2020 1 O-RING, 3.68 I.D. x 1.78 CS
ELF
14
Generac 1300PSI High Pressure Washer
GENERAC
The Reliable Ones
Drawing No. B3720
Exploded View Main Unit
15
Generac 1300PSI High Pressure Washer
GENERAC
The Reliable Ones
Parts List Main Unit
Item Part # Qty Description
1 N/A 1 ASSY., Motor and Pump (see pump exploded view)
2 B1415 1 DECAL, Circuit
3 A1252 1 DECAL, Unit
4 B2525 1 DECAL, Instructions
5 20566 1 DECAL, 1-800 #
6 98806 1 FOAM, Air In, Fan-end
7 97893 1 HOUSING, Switch and Cord
8 20984 1 SWITCH, Rocker 16A
9 98801 4 MOUNT, Rubber
10 B1566 1 COVER, Motor
11 20985 1 ENCLOSURE, Rocker Switch Boot
12 20986 1 BOOT, Rocker Switch
13 84543B 2 SCREW, 3.5mm x 12mm Plastite
14 98805 1 CORD, Power
15 84358 4 SCREW, #6-19 x .75 mm Plastite
16 B1866 1 DECAL, Gun Warning
17 B1053 1 DECAL, ETL
18 NSP 1 DECAL, Data
19 NSP 1 OVERLAMINATE
20 21334 1 HOUSING, Inlet
21 21335 1 HOUSING, Outlet
22 21424 1 CONNECTOR, Garden Hose
23 B1236D 1 NOZZLE, 1.15mm dia. (Lilac)
24 A1484 1 NUT, Strain Relief Lock
25 A1485 1 SEAL RING, Strain Relief
26 97835 1 O RING, Hsg Seal, dia. 82.2 x 2.62mm
27 99350 6 SCREW, #6 Plastite
28 21336 1 GUN, Spray
29 21337 1 WAND, Extension
30 B3337 1 HOSE, High Pressure
31 B1300D 1 NOZZLE, Head
32 A1069 1 FOAMER
33 87815 1 GOGGLES
Generac 1300PSI High Pressure Washer
GENERAC
The Reliable Ones
Limited Pressure Washer Warranties
(includes Master Contractor)
Generac Portable Products warrants to the original retail purchaser, the pressure washer manufactured by Generac
Portable Products to be free from defects in material and workmanship for the period(s) set forth below from the date of
original purchase. This warranty is not transferable. The term original purchaser means the person for whom the
pressure washer is originally purchased.
Warranty Schedules
Electric Power Washer 1 year (does not apply to commercial or rental applications)
CONSUMER* COMMERCIAL*
All Other Engine-driven Engine: Warranted solely by Warranted solely by
Engine Manufacturer Engine Manufacturer
Pump: 1 year 90 days
* NOTE: For the purpose of this warranty consumer use means personal residential household use by original
purchaser. Commercial Use means all other uses, including rental, construction, commercial and income producing
purposes. Once a pressure washer has experienced commercial use, it shall thereafter be considered a commercial use
pressure washer for the purposes of this warranty.
During said warranty period, Generac Portable Products will, at its option, repair or replace any part which, upon
examination by Generac Portable Products or Generac Portable Products Authorized Dealers, is found to be defective
under normal use and service**. All transportation costs under warranty, including return to the factory if necessary, are
to be borne by the purchaser and prepaid by the purchaser.
** NORMAL WEAR: As with all mechanical devices, pressure washers need periodic parts service and replacement to
perform well. This warranty will not cover repair when normal use has exhausted the life of a part or pressure washer
pump.
THIS WARRANTY DOES NOT INCLUDE: Used products and demonstration equipment. Parts such as GUNS, HOSES,
WANDS, NOZZLES or other wear items such as quick couplers, oil, gauges, belts, O-rings, filters, pump packing, etc.
Pumps which have been run without water supplied. Damage or malfunctions resulting from: accidents, abuse,
modifications, alterations, or improper servicing. Freezing or chemical deterioration. Normal maintenance such as
adjustments, fuel system cleaning and obstruction (due to chemical, dirt, carbon or lime, etc.).
THIS WARRANTY IS IN PLACE OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, SPECIFICALLY, Generac
Portable Products MAKES NO OTHER WARRANTIES AS TO MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. The duration of any implied warranties which cannot be disclaimed is limited to the time period as specified
in the express warranty. LIABILITY FOR CONSEQUENTIAL, INCIDENTAL, OR SPECIAL DAMAGES UNDER ANY AND
ALL WARRANTIES IS EXCLUDED, EVEN IF SUCH DAMAGES ARE A DIRECT RESULT OF Generac Portable
Products' NEGLIGENCE. Generac also disclaims any responsibility for incidental or consequential damages such as the
loss of time or the use of the power equipment, or any commercial loss due to the failure of the equipment: and any
implied warranties are limited to the duration of this written warranty.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or
consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific
legal rights and you may also have other rights, which vary from state to state.
For service, see your nearest Generac Portable Products authorized warranty service facility or call 1-877-544-0982.
Warranty service can be performed only by a Generac Portable Products authorized service facility. This warranty will
not apply to service at any other facility. At the time of requesting warranty service, evidence of original purchase date
must be presented.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
Generac Power Systems 01280-0 Owner's manual
- Category
- High-pressure cleaners
- Type
- Owner's manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Simplicity 00777-0 Owner's manual
-
-
-
Simplicity 1040-2 Owner's manual
-
-
-
-
-
-