Poulan Pro BV1850 User manual

Brand: Poulan Pro

Model: BV1850

Category: Air blowers/dryers

Type: User manual

IMPORTANT MANUAL -- Do not throw away

MANUAL IMPORTANTE -- No lo descarte

MANUEL IMPORTANT -- À Conserver

Trademark

ENGLISH

ESPAÑOL

FRANÇAIS

Electrolux Home Products, Inc.

104 Warren Road

Augusta, GA 30907

W ARNING:

Read and follow all Safety Rules and Operating Instructions before

using this product. Failure to do so can result in serious injury .

ADVERTENCIA:

Lea el manual de instrucciones y siga todas las advertencias e

instrucciones de seguridad. El no hacerlo puede resultar en lesiones

graves.

AVERTISSEMENT:

Veuillez lire le manuel d’instructions et bien respecter tous les

avertissements et toutes les instructions de sécurité. Tout défaut

de le faire pourrait entraîner des blessures graves.

2004 Electrolux Home Products, Inc.

530163804

2/2/04

Instruction Manual

Manual de Instrucciones

Manuel d’Instructions

BV200 / BV1650 / BV1800

BV1850 / BV2000

-- 2 --

SAFETY RULES

W ARNING:

Failure to follow all

Safety Rules and Precautions can result in

serious injury.

KNOW YOUR UNIT

Readyourinstructionmanualcarefully until

you completely understandand can follow

all warningsandsafetyrules beforeoperat-

ing the unit.

Restrict unit to users who understandand

will follow all warnings and safety rules in

this manual.

W ARNING:

Inspect area before start-

ing unit. Remove all d ebris and hard objects

su ch as rocks, glass , wire , etc. th at can rico-

chet, be thrown, or otherwise cause injury or

damage during operation.

Use your unit as a blower for:

Sweeping debris or grass clippings from

driveways, side w alks, patios, e t c.

Blowing grassclippings, straw ,or leaves into

piles, around jo ints, or betwe en bricks.

Use your unit as a vacuum for:

Picking up dry material such as leaves,

grass, small twigs, and bits of paper .

For best results during vacuum use, operate

your unit at high speed.

Moveslowly back andforthover themate-

rial as you vacuum. Avoidforcing theunit

intoapileofdebrisasthiscanclogtheunit.

Keep the vacuum tube about an inch above

thegroundforbestresults.

PLAN AHEAD

Always wear eye protection when operat-

ing, servicing, or performing maintenance

on unit. Wearingeye protection will helpto

preventrocksordebrisfrombeingblownor

ricocheting into eyes and face which can

result in blindness and/or serious injury.

Eye protection should be marked Z87.

Always wear foot protection. Do not go

barefoot or wear sandals.

Always wear respirator orface mask when

working with unit in dusty environments.

Secure hair aboveshoulderlength.Secure

or remove jewelry, loose clothing, or cloth-

ing with loosely hanging straps, ties, tas-

sels, etc. They can be caught in moving

parts.

Donotoperateunit when yo uaretired, ill, up-

set, or if you are under the influence of alco-

hol, drugs, or medication.

Keep children, bystanders, and animals

away from work area a minimum of 30feet

(10meters)whenstartingor operatingunit.

Do not point the blower nozzle in thedirec-

tion of people or pets.

HANDLEFUEL WITHCAUTION,ITIS

HIGHLY FLAMMABLE

Eliminate all sources of sparks or flame(in-

cluding smoking, open flames, or work that

cancausesparks)intheareaswherefuelis

mixed, poured, or stored.

Mix and pour fuel in an outdoor area;store

fuel in acool, dry, well ventilated place; use

an approved, marked container for all fuel

purposes.

Do not smoke while handling fuel or while

operating the unit.

Make sure the unit is properly assembled

and in goodoperating condition.

Do not fill fuel tank while engine is hot or

running.

Avoid spilling fuel oroil. Wipe upfuelspills

before starting engine.

Moveatleast 10feet (3meters)awayfrom

fuel andfueling site before starting engine.

Always store gasoline in a container ap-

proved for flammable liquids.

OPERATE YOUR UNITSAFELY

W ARNING:

Stop the engine before

opening the vacuum inlet door. The engine

must be stopped and the impeller blades no

longerturningtoavoid serious injury fromthe

rotating blades.

Inspect unit before each use for worn,

loose, missing, or damaged parts. Do not

use until unit is in proper working order.

Keep outside surfaces free of oil and fuel.

Never start or run engine inside a closed

room, building or other unventilated area.

Breathing exhaust fumes can kill.

To avoid static electricity shock, do not

wear rubber gloves or any other insulated

gloves while operating unit.

Do not set unit on any surface except a

clean, hard area while engine is running.

Debris such as gravel, sand, dust, grass,

etc.couldbepickedupby theairintakeand

thrown out through discharge opening,

damagingunit,property,orcausingserious

injury to bystanders or operator.

Avoiddangerousenvironments.Donotuse

in unventilated areas or where explosive

vapors or carbon monoxide build up could

be present.

Do notoverreachor usefrom unstablesur-

faces such as ladders,trees, steep slopes,

rooftops,etc.Keepfirmfootingandbalance

at all times.

Never place objects inside the blower

tubes; always direct the blowing debris

awayfrompeople,animals,glass, andsolid

objects such as trees, automobiles, walls,

etc.Theforceofaircancauserocks, dirt,or

sticks tobethrownor to ricochet whichcan

hurt people or animals, break glass, or

cause other damage.

Never run unit without the proper equip-

ment attached. When using your unit as a

blower, always install blower tubes. When

using your unit as a vacuum, always install

vacuum tubes and vacuum bag assembly.

Make sure vacuum bag assembly is com-

pletely zipped.

Check air intake opening, blower tubes,

vacuum tubes, and elbow tube frequently,

always with enginestoppedandsparkplug

-- 3 --

disconnected. Keep vents and discharge

tubes free of debris which can accumulate

and restrict proper air flow.

Never place any object in the air intake open-

ing as this could restrict proper air flow and

cause damage to the unit.

Never use forspreadingchemicals, fertiliz-

ers,orothersubstanceswhichmaycontain

toxic materials.

Toavoidspreadingfire,donotusenearleaf

or brush fires, fireplaces, barbecue pits,

ashtrays, etc.

Use only for jobs explained in this manual.

MAINTAIN YOUR UNIT PROPERLY

Have all maintenance other than the rec-

ommendedproceduresdescribed in thein-

struction manual performed by an autho-

rized service dealer.

Disconnect spark plug before performing

maintenance except for carburetor adjust-

ments.

Use only recommended Weed Eater

re-

placement parts; use of any other parts

may voidyourwarrantyandcausedamage

to your unit.

Empty fuel tank before storing the unit. Use

upfuelleftincarburetor bystartingengineand

letting it run un til it stops .

Do not use any accessory or attachment

other than those recommended by manufac-

turer for use with your unit.

Donotstore the unit orfuel in a closedarea

where fuel vapors can reach sparks or an

openflame from hot water heaters,electric

motors or switches, furnaces, etc.

Store in adry area out of reach of children.

SPECIAL NOTICE:

Exposure to vibra-

tions throughprolongeduseof gasoline pow-

ered hand tools could cause blood vessel or

nerve damage in the fingers, hands, and

joints ofpeople proneto circulation disorders

or abnormal swelling. Prolonged use in cold

weatherhasbeenlinked tobloodvesseldam-

agein otherwisehealthypeople.If symptoms

occur such as numbness, pain, loss of

strength, change in skin color or texture, or

loss of feeling in the fingers, hands, or joints,

discontinue the use of this tool and seek

medical attention. An antivibration system

does not guarantee the avoidance of these

problems.Users who operatepower tools on

a continual and regular basis must monitor

closely their physical conditionandthecondi-

tion of this tool.

SPECIALNOTICE:

For user s on U.S.Fo r-

est Land and in some states, including Cali-

fornia (Public Resources Codes 4442 and

4443),Idaho,Maine,Minnesota,NewJersey ,

Oregon, and Washington: Certain internal

combustion engines operated on forest,

brush,and/orgrasscoveredlandin theabove

areas are required to be equipped with a

spark arresting screen, maintained in effec-

tiveworkingorder,ortheenginemust becon-

structed, equipped, and maintained for the

preventionoffire. Checkwith yourstateorlo-

cal authorities for regulations pertaining to

these requirements. Failure to follow these

requirementsis aviolationofthelaw .Thisunit

is not factory equippedwith a spark arresting

screen; however, a spark arresting screen is

availableasanoptionalpart.Ifa sparkarrest-

ing screen is required in your area, contact

your authorizedservice dealer for thecorrect

kit. Thespark arrestingscreen, blowertubes,

andnozzles must be assembled to unit to be

in full compliance with regulations .

ASSEMBLY

W ARNING:

Stop engineand be sure

the impeller blades have stopped turning be-

fore opening the vacuum inlet door or at-

tempting to insert or remove the vacuum or

blower tubes. The rotatingblades can cause

serious injury. Always disconnect the spark

plug before performing maintenance or ac-

cessing movable parts.

W ARNING:

If you receive your unit

assembled, check each step to insure your

unit is properly assembled and all fasteners

are secure. Follow all safety information in

the manual and on the unit.

A standardscrewdriver is requiredfor as-

sembly.

BLOWERTUBE ASSEMBLY

1. Align the rib on the blower tube with the

groove in the blower outlet; slide the tube

into place.

NOTE:

Knobmustbelooseenoughtoallow

blower tube to be inserted in blower outlet.

Loosen knob by turning counterclockwise.

Blower

T ube

Blower

Outlet

Rib

Groove

2. Securethetubeby turningtheknobclock-

wise.

3. Toremovethetube,turntheknobcounter-

clockwise to loosen the tube; remove the

tube.

VACUUM BAG ASSEMBLY

1. Open the zipper on the vacuum bag and

insert the elbow tube.

2. Push the small end of the elbow tube

through the small opening in the bag.

-- 4 --

Small

Opening

Zipper

Opening

Elbow

T ube

Rib

NOTE:

Makesureedgeofthesmall opening

is flush against the flared area of the elbow

tube, and the rib on the elbow tube is on the

bottom.

3. Closethezipperonthebag.Makesurethe

zipper is closed completely.

4. Remove blower tube from engine.

Rib

Groove

5. Inserttheelbowtubeintothebloweroutlet.

Make sure elbow tube rib is aligned with

the blower outlet groove.

6. Turnknobclockwise tosecureelbowtube.

VACUUM TUBE ASSEMBLY

W ARNING:

Stop engineand be sure

the impeller blades have stopped turning be-

fore opening the vacuum inlet door or at-

tempting to insert or remove the vacuum or

blower tubes. The rotatingblades can cause

serious injury.

1. Align the lower vacuum tube as shown.

Push lower vacuum tubeinto uppervacu-

um tube.

Lower Vacuum Tube

Upper Vacuum

T ube

2. Insert thetipofa screwdriverintothelatch

area of the vacuum inlet.

Latch Area

Blower

Outlet

Vacuum

Inlet Cover

Latch

Area

3. Gently tilt thehandleof thescrewdriverto-

ward the back of the unit to release the

latch while pulling up on the vacuum inlet

cover with your other hand.

4. Holdthevacuum inlet cover openuntilup-

per vacuum tube is installed.

Vacuum Inlet

Vacuum

Inlet

Cover

Retaining Post

5. Placethehooksof theuppervacuum tube

on the retaining posts of the unit.

6. Pivot the tube until it is secured to the

blower unit by the vacuum inlet latch.

Retaining

Post

Hook

Inlet Cover

Latch

PIVOT

HOW TO CONVERT UNIT FROM

VACUUM USE TO BLOWER USE

1. Remove the vacuum tubes by inserting

the tip of a screwdriver into the latch area

of the vacuum inlet.

2. Gently tilt handle of screwdriver toward

the back of the unit to release the latch

whilepullingupontheuppervacuumtube

with your other hand.

Latch Area

3. Remove the vacuum bag.

4. Close the vacuum inlet cover and make

sure it is latched closed.

5. Reinstall the blower tube (see BLOWER

TUBE ASSEMBLY).

-- 5 --

SHOULDERSTRAP ADJUSTMENT

1 Hold the unit as shown with the muffler side

facing away from your body an d clothes.

2. Pass the shoulder strap over your head

and onto your right shoulder.

3. Extend your left arm towardthe rearofthe

vacuum bag.

4. Adjust shoulder strap until the vacuum

bag/shoulder strap seam lies between

your thumb and index finger.

5. Make sure air flows freely from the elbow

tubeintobag. If bagis kinked, the unit will

not operate properly.

OPERATION

KNOW YOUR B LOWER

READTHISINSTRUCTIONMANUALANDSAFETYRULESBEFORE OPERA TINGYOUR UNIT.

Compare th eillustrations wit h you run it tofamilia rize yo urse lfwit hthelocationoft he var ious con trols

and adjustments. Save this manual for future reference.

Choke Lever

Fuel Mix

Fill Cap

Starter

Rope

Throttle

Lever

Spark Plug

Blower

T ube

Primer Button

Rear

Handle

Lower

Vacuum Tube

Upper

Vacuum Tube

Vacuum Bag

Elbow Tube

THROTTLE LEVER

TheTHROTTLELEVER is usedtoselect the

desiredenginespeedand tostop theengine.

Movethethrottlelevertothe

positionfor

full speed operation. Move the throttle lever

tothe

positionforidlespeed. Tostopthe

engine, move the throttle lever to the STOP

position.

PRIMERBUTTON

The PRIMER BUTTON removes air from the

carburetora nd fu el linesand fills them with fuel.

T his allows you to start the engin e wit h f ewer

pulls on the starter rope. Activate primer button

by pressingit andallowing it to return to its origi-

nal position.

CHOKE LEVER

The CHOKE helps to supply fuel to the engine

to aid in cold starting. Activate the choke by

moving the choke lever to the FULL CHOKE

position.Afterengineattemptstostart, moveth e

choke lever to the HALF CHOKE position.

Once engine starts, move choke lever to the

R U N p osition.

-- 6 --

OPERATING POSITION

Blower

Eye

Protection

Vacuum

OPERATING TIPS

While vacuuming or blowing debris, hold

the unit with the muffler side facing away

from your body and clothes (seeOPERAT-

ING POSITION illustration above).

To reduce the risk of hearing loss

associated with sound level(s), hearing

protection is required.

To reduce the risk of injury associated with

contacting rotating pa rts, stop the engine be-

fore installing or r emo ving a tta chme nts. Do

not op erate without guard(s) in place.

Operate power equipment only a t reasonable

hours--not early in the morning or late at night

whenpeoplemightbe disturbed.Comply with

times listed in local ordinances. Usual recom-

mendations are 9:00 a.m. to 5:00 p.m.,

Monday though Saturday .

To reduce noise levels, limit the number of

pieces of equipmentused at any one time.

To reduce noise levels, operate power

blowers at the lowest possible throttle

speed to do the job.

Use rakes andbrooms toloosen debrisbe-

fore blowing.

In dusty conditions, slightly dampen sur-

faces or use amister attachmentwhenwa-

ter is available.

Con serve wat er by using powe r blower s

instead of hoses for many lawn and garden

applications, including areas such as g utters,

screens, pa tio s, grills, po r ches, andgarden s.

Watchoutforchildren,pets,openwindows,

or freshly washed cars. Blow debris away

safely.

Use the full blower nozzle extension so the

air stream can work close to the ground.

After using blowers and other equipment,

CLEAN UP! Dispose of debris in trash re-

ceptacles.

BEFORE STARTING ENGINE

W ARNING:

Be sure to read the fuel

information in the safety rules before you be-

gin.If you donot understandthe safetyrules,

do not attempt to fuel your unit. Call

1-800-554-6723

FUELING ENGINE

W ARNING:

Remove fuel cap slowly

when refueling.

This engine is certified to operate on

unleaded gasoline. Before operation,

gasoline must be mixed with a good quality

synthetic 2-cycle air-cooled engine oil

designed to be mixed at a ratio of 40:1.

Poulan/Weed Eater brand synthetic oil is

recommended.Mix gasoline and oil at a ratio

of40:1. A40:1ratiois obtainedby mixing3.2

ounces (95 ml) of oil with 1 gallon (4 lit ers) of

unleaded gasoline. DO NOT USE

automotiveoilorboatoil.Theseoils willcause

engine damage. When mixing fuel, follow

instructions printed on container. Once oil is

added to gasoline, shake container

momentarily to assure that the fuel is

thoroughlymixed.Always readandfollow the

safetyrulesrelatingtofuelbeforefuelingyour

unit.

IMPORTANT

Experience indicates that alcohol blended

fuels (called gasohol or using ethanol or

methanol)canattractmoisturewhichleads to

separation and formation of acids during

storage. Acidic gas can damage the fuel

systemofanenginewhileinstorage.Toavoid

engine problems, empty the fuel system

beforestoragefor30daysorlonger.Drainthe

gastank,starttheengineandlet itrununtilthe

fuellines andcarburetorareempty.Usefresh

fuel next season. Never use engine or

carburetorcleanerproductsinthefuel tankor

permanent damage may occur.

NOTE:

Unit must be placed on its side when

a ddin g f uel (se e illustrat ion below).

TO STOP THE ENGINE

To stop the engine, move the throttle lever

to the STOP position.

BEFORE STARTING THE ENGINE

W ARNING:

YouMUSTmakesure

the tubes are secure before using the unit.

Fuel engine. Move at least 10 feet (3 me-

ters) away from the fueling site.

Hold the unit in the starting position as

shown. Make sure the blower end is di-

rected away from people, animals, glass,

and solid objects.

-- 7 --

Blower

Vacuum

STARTING POSITION

W ARNING:

When starting engine,

h oldthe unit asillustrat ed.Donotse tunit onan y

surface except aclean, hardarea when starting

engine or while engine is running. Debris such

as gravel, sand, dust, grass, etc. could be

picked up by the air intake and thrown out

through the discharge open ing, damaging the

unit or prope rty , or causing serious injury to by-

standers or the op erator .

STARTING A COLD ENGINE

1. Move throttle lever to the position.

2. Move choke lever to the FULL CHOKE

position.

3. Slowly press the primer button8 times.

Throttle Lever

Choke Lever

Primer Button

4. Pull starter rope sharply until engine at-

temptstorun,butnomorethan5pulls(be-

low 30

F, 8 pulls).

NOTE:

If engine attempts tostart beforethe

pull, go to next step immediately.

5. Move the choke lever to the HALF

CHOKE position.

6. Pull the starter rope sharply until the en-

gine runs,but no more than 5 pulls (below

F, 10 pulls).

7. After a 5 second warm--up, move the

choke lever to the RUN position.

8. Allow the unit to run for 30 more seconds

at the RUN position before moving the

throttle lever to

position.

If en gine has not started after 5 pulls (at HALF

CHOKE), repeatST ARTING A COLDENGINE

procedure. If engine still doe s not start,proceed

to STAR TING A FLOODED ENGINE.

9. To stop the engine, move thethrottle lever to

the STOP po sition .

STARTING A WARM ENGINE

NOTE:

If fuel tank is empty, add fuel; then,

follow STARTING A COLD ENGINE proce-

dure. Do not fill fuel tank while engine is hot.

1. Move throttle lever to the

position.

2. Pull starter rope sharply until engineruns,

but no more than 5 pulls.

NOTE

If engine has not started, pull starter

rope5more pulls. Ifengine still does notrun,

it is probably flooded.

3. To stop the engine, move thethrottle lever to

the STOP po sition .

STARTING A FLOODED ENGINE

Flooded e ngines can b e started by placing th e

choke lever in the RUN position. Move throttle

le ver to the fa st po sitio n

; then, pull rope

until engine starts. After enginestarts, movethe

throttle lever to the slow position

toallow

e ngin e to idle .

St arting could re quire pulling the sta rter rope

many times depending on how badly the unit is

flooded.

If unit still doesn’t start refer to the TROUBLE-

SHOOTING TABLE or call 1-800-554-672 3

MAINTENANCE

W ARNING:

Avoid touching muffler

unless engine and muffler are cold. A hot

muffler can cause serious burns.

W ARNING:

Stop engineand be sure

the impeller blades have stopped turning be-

fore opening the vacuum inlet door or at-

tempting to insert or remove the vacuum or

blower tubes. The rotatingblades can cause

serious injury. Always disconnect the spark

plug before performing maintenance or ac-

cessing movable parts.

GENERALRECOMMENDATIONS

Thewarrantyonthisunitdoesnotcoveritems

that have been subjected to operator abuse

or negligence. To receive full value from the

warranty, the operator must maintain unit as

instructed in this manual. Various adjust-

ments will need to be made periodically to

properly maintain your unit.

CHECK FOR LOOSE

FASTENERS AND PARTS

Spark Plug Boot

Air Filter

Housing Screws

Muffler

CHECK FOR DAMAGED OR WORN

PARTS

Contact an authorized service dealer for re-

placement of damaged or worn parts.

Fuel Tank -- Do not useunit if fuel tankshows

signs of damage or leaks.

Vacuum Bag -- Do notuse vacuum bag if it

is torn or damaged.

-- 8 --

INSPECTAND CLEAN UNIT AND

DECALS

After each use, inspect complete unit for

looseordamagedparts. Cleantheunitand

decals usingadampcloth withamilddeter-

gent.

Wipe off unit with a clean dry cloth.

CLEAN AIR FILTER

Air Filter

Cover

Air Filter

Screws

Cleaning the air filter:

A dirty air filter decreases engine perform-

ance and increases fuel consumption and

harmful emissions. Always clean or replace

air filter after every 5 hours of operation or

yearly, whichever comes first.

1. Clean the cover and the area around it to

keepdebrisfrom fallingintothecarburetor

chamber when the cover is removed.

2. Remove parts as illustrated.

NOTE:

Do no t cle an filter in g asolin e or oth er

flammable solvent. Doing so can create a fire

hazard or produce harmful e vaporative emis-

sions.

3. Wash the filter in soap and water.

4. Allow filter to dry.

5. Apply a few drops of oil to the filter;

squeeze filter to distribute oil.

6. Replace parts.

REPLACE SPARK PLUG

Replace spark plug each year to ensure the

engine starts easier and runs better. Set

sparkpluggapat0.025inch.Ignition timing is

fixed, nonadjustable.

1. Twist, then pull off spark plug boot.

2. Removespark plug from cylinder and dis-

card.

3. Replace with Champion RCJ-6Y spark

plug and tighten securely with a 3/4 inch

socket wrench.

4. Reinstall the spark plug boot.

REPLACE FUEL FILTER

Toreplacefuelfilter,drainunitbyrunningitdry

of fuel, then remove fuel cap/retainerassem-

bly fromtank. Pull filter from tank andremove

itfromthefuelline. Installnewfuelfilter onfuel

line; reinstall parts.

Fuel Line

Fuel Filter

CHECK MUFFLER MOUNTING

SCREWS

Once each year, ensure muffler mounting

screws are secure and tightened properly to

prevent damage.

Mounting

Screw

Holes

Muffler Cover

Screws

1. Loosenandremovethe2screws fromthe

muffler cover.

2. Remove the muffler cover.

3. Tightenthe 2 muffler mountingscrews se-

curely.

4. Reinstall muf fler cover and 2 screws.

Tighten securely.

CARBURETOR ADJUSTMENT

Thereis no screw for idle adjustment onyour

blower. The throttle lever is used to control

engine speed. The throttle lever can be

placed in one of four positions: STOP, IDLE

, FULL THROTTLE or , and one

intermittentposition. Ifyourenginewill notrun

properly or you require further assistance,

contact an authorized service dealer or call

1--800--554--6723.

STORAGE

W ARNING:

Perform the following

steps after each use:

Allow engine to cool, and secure the unit

before storing or transporting.

Store unit and fuel in a well ventilated area

where fuel vapors cannot reach sparks or

open flames from water heaters, electric

motors or switches, furnaces, etc.

Store unit with all guards in place. Position

unit so that any sharp object cannot acci-

dentally cause injury.

Store unit and fuel well out of the reach of

children.

-- 9 --

SEASONALSTORAGE

Prepareunit forstorageatendof season or if

it will not be used for 30 days or more.

If your unitis tobe storedfor a period of time:

Clean the entire unit before lengthy stor-

age.

Store in a clean dry area.

Lightly oil external metal surfaces.

FUEL SYSTEM

Under FUELING ENGINE in the OPERA-

TIONsectionofthis manual,seemessagela-

beled IMPORTANT regarding the use of ga-

sohol in your engine.

Fuel stabilizer is a n a cceptable alternative in

minimizing the formation of fuel gum deposits

d uringsto rag e. Add stabilizer to g asolin e in fu el

tank or fuel storage container . Follow the mix

in structions f ound on sta bilize r container. Run

e ngin eatleast 5minutes after ad dingstabilizer.

ENGINE

Remove spark plugandpour1teaspoonof

40:1,2-cycleengineoil (aircooled)through

the spark plug opening. Slowly pull the

starter rope 8 to 10 times to distribute oil.

Replacespark plugwith newone ofrecom-

mended type and heat range.

Clean air filter .

Check entire unit for loose screws, nuts,

and bolts. Replace any damaged, broken,

or worn parts.

At the beginning of the next season, use

only freshfuelhavingthepropergasolineto

oil ratio.

OTHER

Do not store gasoline from one season to

another.

Replaceyourgasolinecanifitstarts torust.

TROUBLE

CAUSE REMEDY

Engine will not

start.

1. Engine flooded.

2. Fuel tank empty.

3. Spark plug not firing.

4. Fuel not reaching

carburetor.

5. Compression low.

1. See “Starting a Flooded Engine”

in Operation section.

2. Fill tank with correct fuel mixture.

3. Install new spark plug.

4. Check for dirty fuel filter; replace.

Check for kinked or split fuel line;

repair or replace.

5. Contact an authorized service dealer.

Engine will not

idle properly.

1. Fuel not reaching

carburetor.

2. Carburetor requires

adjustment.

3. Crankshaft seals worn.

4. Compression low.

1. Check for dirty fuel filter; replace.

Check for kinked or split fuel line;

repair or replace.

2. Contact an authorized service dealer.

3. Contact an authorized service dealer

4. Contact an authorized service dealer.

1. Air filter dirty.

2. Fuel not reaching

carburetor.

3. Spark plug fouled.

4. Carburetor requires

adjustment.

5. Carbon build up.

6. Compression low.

Engine will not

accelerate,

lacks power, or

dies under a

load.

1. Clean or replace air filter.

2. Check for dirty fuel filter; replace.

Check for kinked or split fuel line;

repair or replace.

3. Clean or replace spark plug

and re-gap.

4. Contact an authoriz ed ser vice d ealer .

5. Contact an authoriz ed ser vice d ealer .

6. Contact an authoriz ed ser vice d ealer .

Engine smokes

excessively.

1. Choke partially on.

2. Fuel mixture incorrect.

3. Air filter dirty.

4. Carburetor requires

adjustment.

1. Adjust choke.

2. Empty fuel tank and refill with

correct fuel mixture.

3. Clean or replace air filter.

4. Contact an authorized service dealer.

Engine runs hot.

1. Fuel mixture incorrect.

2. Spark plug incorrect.

3. Carburetor requires

adjustment.

4. Carbon build up.

1. See “Fueling Engine” in Operation

section.

2. Replace with correct spark plug.

3. Contact an authorized service dealer.

4. Contact an authorized service dealer.

TROUBLESHOOTINGTABLE

W ARNING:

Always stopunit and disconnectspark plugbefore performingany of the

recommended remedies below other than remedies that require operation of the un it.

-- 10 --

LIMITED WARRANTY

ELECTROLUX HOME PRODUCTS, INC.,

warrants to the original purchaser that each

new

WeedEaterr

brandgasolinetool or at-

tachment is freefrom defects in material and

workmanship andagreesto repair or replace

under this warranty any defective gasoline

product or attachment as follows from the

original date of purchase:

2 YEARS --

Parts and Labor, when used for

household purposes.

90 DA YS --

Parts an d Labor, when used for

commercial, professional, or income producing

purposes.

30 DA YS --

Parts and Labor , if used for rental

purposes.

This warranty is not transferable and does not

cove r da m age or liability cause d by imp r ope r

han dling, improper maintenance, or the use of

accessories and/or attachments not specifically

recommended by

ELECTROLUX HOME

PRODUCTS , INC. ,

for this tool. Additionally,

this warranty does not cover tune-ups, spark

plugs, filters, starter ropes, starter springs, cut-

ting line,orrotating headparts thatwill wearand

require replacement with reasonable useduring

the warranty period. This warranty does not

cover predelivery setup or normal adjustments

explained in the instruction manual.

THIS WARRANTY GIVES YOU SPECIFIC

LE GAL RIGHTS, AND YOU MAY HA VE

OTHER RI GHTS WHICH VAR Y FRO M

STA TE T O STA TE.

NO CLAIMS FOR CONSEQUENTIAL OR

OTHER DAMAGES WILL BE ALLOWED,

AND THERE ARE NO OTHER EXPRESS

WARRANTIES EXCEPT THOSE EX-

PRESSL Y STIPULA TED HEREIN.

SOME ST ATES DO NOT ALLOW LIMIT A-

TIONS ON HOW LONG AN IMPLIED WAR-

RANTY LASTS OR THE EXCLUSION OR

LI MITATIONS OF INCIDEN TAL OR CONSE-

QUENTIAL DAMAGES, SO THE ABOVE

L I MI TA T IONS OR EXC L US ION MAY NOT

APPL Y TO YOU.

T he polic y o f

ELECTROLUX HOME PROD-

UCTS,INC.,

is to continuouslyimprove itsprod-

ucts. The refore,

ELECTROLUX HOME

PRODUCTS , INC.,

reserves the right to

change, modify , or discontinue models, de-

signs, specifications, and accessories of all

products at any time without notice or obligation

to a ny purchaser .

U.S. EPA

EMISSION CONTROL WARRANTY STATEMENT

YOUR WARRA NTY RIGHTS AND OBLIGA-

TIONS:

The U. S. Environmental Protection

Agen cy and ELECTROLUX HOME PROD-

UCTS, INC., are pleased to explain the emis-

sions control system warranty on your year

2002--2004 small off--road engine. ELECTRO-

LUX HOME PRODUCTS, INC., must warrant

t h e emissio n contro l syste m on yo u r small off--

road e ngine for the periods of time listed below

provided there has been no abuse, neglect, or

improper maintenance of your small o ff--road

engine. Y our emission control system includes

parts such as the carburetor and the ignition

syst em. Where a wa r rantable cond ition exist s,

EL ECT ROLUX HOME P RODUCTS , INC.,will

repair your small off--road engine at no cost to

you. Expenses covered underwarranty include

diagnosis, parts and labor .

MANUFACTUR-

ER’S WARRANT Y COVERAGE:

If an y e mis-

sions related part on your engine (as listed un-

der Emissions Control Warranty Parts List) is

d efective or a defect in th e materials o r work-

manshipoftheenginecauses thefailureofsuch

anemissionrelatedpart,thepartwill berepaired

or replaced by ELECTROLUX HOME PROD-

UCTS, INC.

OWNER’S WARR ANT Y RE-

SPONSIBILITIES:

As the small of f--road en-

gine owner , you are responsible for the p erfor-

mance of the required maintena nce listed in

your instructionmanual. ELECTROLUXHOME

PRODU CTS, INC., recomme n ds that you re-

tain all receipts covering maintenance on your

small off--road engine, but ELECTROLUX

HOME PRODUCTS, INC., cannot deny war-

ranty solely for the lack of receipts or for your

failure to ensure the performance of all sched-

uled maintenance. As the small off--road en-

gine owner , you should be aware that ELEC-

TROL UXHOME PRODUCTS ,INC.,mayde n y

you warranty coverage if your small off--road

engineora partof it has failed due to abuse, ne-

glect, impropermaintenance, unapprovedmod-

ifications, or the use of parts not made or ap-

proved by the original eq uipment manufa cturer.

You are responsible for presenting your small

of f--road engine to an ELECTROLUX HOME

PRODUCTS, INC., authorized repair center as

soon as a problem exists. Warranty repairs

should be completed in a reasonable amount of

time, not to exceed 30 days. If you have any

questionsregardingyourwarrantyrights andre-

sp onsib ilit ies, you shou ld con tact your ne arest

auth orized service center or call ELECTRO-

LUX HOME PRODUCTS , INC., at

1--800--554--6723.

W ARRAN TY COM-

MENCEMENTDATE:

The warranty period be-

gins on the date the small off--road engine is

purchased.

LENGTH OF COVERAGE:

This

warranty shall be for aperiod oftwo years from

the initial date of purchase.

WH AT IS COV-

ERED: REP AIR OR REPLACEMENT OF

PARTS.

Repair or replacement of any war-

rantedpartwill beperformed at nocharge to the

owner at an approved ELECTROLUX HOME

PRODUCTS, INC., servicing center. If you

have any questions regarding your warranty

rights an d responsibilities, you should contact

your nearest authorized service cente r or call

EL ECTR OLUX HOME PRODUCT S, INC., at

1--800--554--6723.

W ARRANT Y PERI OD:

Any warranted part which is not scheduled for

replacement as required maintenance, or which

-- 11 --

isscheduledonlyforregularinspectionto theef-

fect of “repair or replace as necessary” shall be

warrantedfor2years. Anywarrantedpartwhich

is scheduled for replacement as required main-

tenanceshall be warrantedfortheperiodoftime

up to the first scheduled replacement point for

that part.

DIAGNOSI S:

The owner shall not be

charged for diagnostic labor which leads to the

dete rmination that a warranted part is defective

if the diagnostic work is performed at an ap-

proved ELECTROLUX HOME PRODUCTS,

I N C . , se r vic ing cen t er.

CONSEQUENT IAL

DAMAGES:

ELECTROLUX HOME PROD-

UCTS, INC., may beliablefor damages toother

engine components caused by the failure of a

warranted part still under warranty .

WHAT IS

NOT COVERED:

All failures caused by abuse,

neglect, or improper maintenance are not cov-

ered.

ADD--ON OR MODIFIED P ARTS:

The

use of add--on or modified parts can be grounds

f or disa llowing a warranty claim . ELECTRO-

LUX HOME PRODUCTS , INC., is no t liab le to

cover failures of warranted parts caused by the

useofadd--onormodifiedparts.

HOW TOFILE

ACLAIM:

If you have any questions regarding

yo ur w arranty rights an d res pon sibilities, yo u

should contact your nearest authorized service

center or call ELECTROLUX HOME PROD-

UCTS, INC., at 1--800--554--6723.

WHER ETO

GET W ARRANTY SER V ICE:

Warranty ser-

vices or repairs shall be provided at all ELEC-

TROL UX HOME PRODUCTS, INC., service

centers. Call 1--800--554--6723.

MAINTE-

NANCE, REPLACE MENT AND REP A IR OF

EMISSION RELA TED PART S:

An y ELEC-

TROL UX HOMEPRODUCTS , INC.,ap p ro ved

replacement part used in the performance of

any warranty maintenance or repair on emis-

sion related parts will be provided without

charge to theownerif the partis underwarranty.

EMISSI ON CONTROL WARRANTY P ARTS

LIST:

Carburetor, Ignition System: Spark Plug

(covered up to maintenance schedule), Ignition

Mod ule .

MAINTENANCE ST ATEMENT:

The

owner is responsible for the performance of all

required maintenance as defined in the instruc-

tion manual.

This engine is certified to be emissions compliant for the following use:

Moderate (50 hours)

Intermediate (125 hours)

Extended (300 hours)

Poulan Pro BV1850 User manual

Brand: Poulan Pro

Model: BV1850

Category: Air blowers/dryers

Type: User manual

Download PDF

report

Poulan Pro BV1850 User manual

Poulan Pro BV1850 User manual

Related papers

Other documents