Asus P4B533-X User manual

Motherboard

P4B533-X

User Guide

ii

Checklist

No part of this manual, including the products and software described in it, may be

reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any

language in any form or by any means, except documentation kept by the purchaser for

backup purposes, without the express written permission of ASUSTeK COMPUTER INC.

(“ASUS”).

Product warranty or service will not be extended if: (1) the product is repaired, modified or

altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2)

the serial number of the product is defaced or missing.

ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER

EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES

OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE

LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES

(INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE

OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN

ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR

ERROR IN THIS MANUAL OR PRODUCT.

SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED

FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME

WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS.

ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR

INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS

AND SOFTWARE DESCRIBED IN IT.

Products and corporate names appearing in this manual may or may not be registered

trademarks or copyrights of their respective companies, and are used only for identification or

explanation and to the owners’ benefit, without intent to infringe.

E1458

First Edition

November 2003

iii

Features

Contents

Notices ...........................................................................................vi

Safety information ......................................................................... vii

About this guide............................................................................ viii

Conventions used in this guide ........................................... viii

Where to find more information ........................................... viii

P4B533-X specification summary ..................................................ix

Chapter 1: Product introduction

1.1 Welcome! ........................................................................... 1-2

1.2 Package contents............................................................... 1-2

1.3 Special features.................................................................. 1-3

1.3.1 Product highlights .................................................. 1-3

1.3.2 Unique ASUS features ........................................... 1-4

1.4 Before you proceed ............................................................ 1-5

1.5 Motherboard overview........................................................ 1-6

1.5.1 Motherboard layout ................................................ 1-6

1.5.2 Placement direction ............................................... 1-7

1.5.3 Screw holes ........................................................... 1-7

1.6 Central Processing Unit (CPU)........................................... 1-8

1.6.1 Overview ................................................................ 1-8

1.6.2 Installing the CPU .................................................. 1-9

1.7 System memory ............................................................... 1-10

1.7.1 DIMM sockets location......................................... 1-10

1.7.2 Installing a DIMM ..................................................1-11

1.8 Expansion slots .................................................................1-11

1.8.1 Standard interrupt assignments ........................... 1-12

1.8.2 IRQ assignments for this motherboard ................ 1-12

1.8.3 PCI slots .............................................................. 1-13

1.8.4 AGP slot............................................................... 1-13

1.9 Jumpers............................................................................ 1-14

1.10 Connectors ....................................................................... 1-16

1.10.1 Rear panel connectors......................................... 1-16

1.10.2 Internal connectors .............................................. 1-17

iv

Safeguards

Contents

Chapter 2: BIOS information

2.1 Managing and updating your BIOS .................................... 2-2

2.1.1 Creating a bootable floppy disk ............................. 2-2

2.1.2 Using AFUDOS to copy the current BIOS ............. 2-3

2.1.3 Using AFUDOS to update the BIOS ...................... 2-3

2.1.4 Using ASUS EZ Flash to update the BIOS ............ 2-5

2.1.5 Recovering the BIOS with CrashFree BIOS 2 ....... 2-6

2.2 BIOS Setup program .......................................................... 2-8

2.2.1 BIOS menu screen ................................................ 2-9

2.2.2 Menu bar................................................................ 2-9

2.2.3 Navigation keys ..................................................... 2-9

2.2.4 Menu items .......................................................... 2-10

2.2.5 Sub-menu items................................................... 2-10

2.2.6 Configuration fields .............................................. 2-10

2.2.7 Pop-up window .................................................... 2-10

2.2.8 Scroll bar.............................................................. 2-10

2.2.9 General help ........................................................ 2-10

2.3 Main menu.........................................................................2-11

2.3.1 System Time [xx:xx:xxxx]......................................2-11

2.3.2 System Date [Day xx/xx/xxxx] ..............................2-11

2.3.3 Legacy Diskette A [1.44M, 3.5 in.] ........................2-11

2.3.4 Primary and Secondary IDE Master/Slave .......... 2-12

2.3.5 System Information .............................................. 2-13

2.4 Advanced menu ............................................................... 2-14

2.4.1 JumperFree Configuration ................................... 2-14

2.4.2 CPU Configuration................................................ 2-16

2.4.3 Chipset.................. ............................................... 2-16

2.4.4 Onboard Devices Configuration........................... 2-17

2.4.5 PCI PnP ............................................................... 2-20

2.5 Power menu ..................................................................... 2-22

2.5.1 Suspend Mode [Auto] .......................................... 2-22

2.5.2 Repost Video on S3 Resume [No] ....................... 2-22

2.5.3 ACPI 2.0 Support [No] ......................................... 2-22

2.5.4 ACPI APIC Support [Enabled] ............................. 2-22

2.5.5 APM Configuration............................................... 2-23

2.5.6 Hardware Monitor ................................................ 2-24

v

2.6 Boot menu ........................................................................ 2-25

2.6.1 Boot Device Priority ............................................. 2-25

2.6.2 Removable Drives ............................................... 2-26

2.6.3 Boot Settings Configuration ................................. 2-26

2.6.4 Security ................................................................ 2-28

2.7 Exit menu ......................................................................... 2-30

Chapter 3: Software support

3.1 Install an operating system................................................. 3-2

3.2 Support CD information...................................................... 3-2

3.2.1 Running the support CD ........................................ 3-2

3.2.2 Drivers menu ......................................................... 3-3

3.2.3 Utilities menu ......................................................... 3-4

3.2.4 ASUS Contact Information..................................... 3-5

Contents

vi

Notices

Federal Communications Commission Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to

the following two conditions:

• This device may not cause harmful interference, and

• This device must accept any interference received including interference

that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with

manufacturer’s instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment to an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Canadian Department of Communications Statement

This digital apparatus does not exceed the Class B limits for radio noise

emissions from digital apparatus set out in the Radio Interference

Regulations of the Canadian Department of Communications.

This class B digital apparatus complies with Canadian ICES-003.

The use of shielded cables for connection of the monitor to the

graphics card is required to assure compliance with FCC regulations.

Changes or modifications to this unit not expressly approved by the

party responsible for compliance could void the user’s authority to

operate this equipment.

vii

Safety information

Electrical safety

• To prevent electrical shock hazard, disconnect the power cable from

the electrical outlet before relocating the system.

• When adding or removing devices to or from the system, ensure that

the power cables for the devices are unplugged before the signal

cables are connected. If possible, disconnect all power cables from the

existing system before you add a device.

• Before connecting or removing signal cables from the motherboard,

ensure that all power cables are unplugged.

• Seek professional assistance before using an adpater or extension

cord. These devices could interrupt the grounding circuit.

• Make sure that your power supply is set to the correct voltage in your

area. If you are not sure about the voltage of the electrical outlet you

are using, contact your local power company.

• If the power supply is broken, do not try to fix it by yourself. Contact a

qualified service technician or your retailer.

Operation safety

• Before installing the motherboard and adding devices on it, carefully

read all the manuals that came with the package.

• Before using the product, make sure all cables are correctly connected

and the power cables are not damaged. If you detect any damage,

contact your dealer immediately.

• To avoid short circuits, keep paper clips, screws, and staples away from

connectors, slots, sockets and circuitry.

• Avoid dust, humidity, and temperature extremes. Do not place the

product in any area where it may become wet.

• Place the product on a stable surface.

• If you encounter technical problems with the product, contact a

qualified service technician or your retailer.

viii

About this guide

Conventions used in this guide

To make sure that you perform certain tasks properly, take note of the

following symbols used throughout this manual.

Where to find more information

Refer to the following sources for additional information and for product

and software updates.

1. ASUS Websites

The ASUS websites worldwide provide updated information on ASUS

hardware and software products. The ASUS websites are listed in the

ASUS Contact Information on the inside front cover.

2. Optional Documentation

Your product package may include optional documentation, such as

warranty flyers, that may have been added by your dealer. These

documents are not part of the standard package.

WARNING: Information to prevent injury to yourself when trying

to complete a task.

CAUTION: Information to prevent damage to the components

when trying to complete a task.

IMPORTANT: Information that you MUST follow to complete a

task.

NOTE: Tips and additional information to aid in completing a task.

ix

P4B533-X specification summary

CPU

Chipset

Front Side Bus (FSB)

Memory

Expansion slots

Storage

Audio

LAN

USB

Special features

Extreme Overclocking

Rear panel I/O

(continued on the next page)

Socket 478 for Intel

®

Pentium

®

4 / Celeron processors with

speeds up to 3.06GHz+

Intel

®

Hyper-Threading technology ready

Intel 845E MCH

Intel ICH4

800*/533/400 MHz

* Overclocking mode

2 x 184-pin DDR DIMM sockets for up to 2GB memory

Supports PC3200*/PC2700*/PC2100/PC1600 unbuffered

non-ECC DDR DIMMs

* Overclocking feature support PC3200/PC2700

1 x AGP 4X (1.5V only)

4 x PCI

2 x UltraDMA 100/66/33

ADI AD1888 SoundMAX 6-channel audio CODEC

S/PDIF out interface

Realtek 10/100 Mbps Ethernet LAN controller

Supports 6 USB 2.0 ports

ASUS EZ Flash

ASUS CrashFree BIOS2

ASUS MyLogo

ASUS C.P.R (CPU Parameter Recall)

STR (Suspend-To-RAM)

STD (Suspend-To-Disk)

Wake-On-Ring, Wake-On-LAN

Wake-On-Keyboard, Wake-On-Mouse

Support for S/PDIF-out on back of I/O port

ASUS JumperFree

ASUS C.P.R. (CPU Parameter Recall)

SFS (Stepless Frequency Selection) from 100MHz up to

266MHz at 1MHz increment

Adjustable FSB/DDR ratio

AGP/PCI Asynchronous Mode with FSB

1 x Parallel port

1 x Serial port

1 x PS/2 keyboard port

1 x PS/2 mouse port

1 x S/PDIF out port

1 x RJ-45 port

4 x USB 2.0/1.1 ports

Line In/Line Out/Microphone ports

x

P4B533-X specification summary

* Specifications are subject to change without notice.

CPU/Chassis FAN connectors

20-pin ATX power connector

4-pin ATX 12V power connector

GAME/MIDI connector

CD/AUX audio in

Front panel audio connector

1 x USB 2.0 connector supports additional 2 USB 2.0 ports

20-pin Panel connector

3Mb Flash ROM, AMI BIOS, PnP, DMI2.0, WfM2.0, SM

BIOS 2.3, ACPI, ASUS EZ Flash, ASUS MyLogo, ASUS

CrashFree BIOS2, ASUS C.P.R.

PCI 2.2, USB 2.0/1.1

WfM2.0, DMI2.0, WOR by PME, WOL by PME

ATX form factor: 12 in x 7 in (30.5 cm x 17.8 cm)

Device drivers

ASUS PC Probe

ASUS LiveUpdate

Trend Micro™ PC-cillin 2002 anti-virus software (

OEM version)

Internal I/O

connectors

BIOS features

Industry standard

Manageability

Form Factor

Support CD contents

Chapter 1

This chapter describes the features of the

motherboard. It includes brief descriptions of the

motherboard components, and illustrations of the

layout, jumper settings, and connectors.

Product introduction

1-2

Chapter 1: Product introduction

1.1 Welcome!

Thank you for buying the ASUS

®

P4B533-X motherboard!

The motherboard incorporates the Intel

®

Pentium

®

4 processor in a 478-pin

package coupled with the Intel

®

845E chipset to set a new benchmark for an

effective desktop platform solution.

Before you start installing the motherboard, and hardware devices on it, check the

items in your package with the list below.

1.2 Package contents

Check your motherboard package for the following items.

If any of the above items is damaged or missing, contact your retailer.

ASUS motherboard

ASUS motherboard support CD

80-conductor UltraATA IDE cable

Ribbon cable for a 3.5-inch floppy drive

I/O shield

Bag of extra jumper caps

User Guide

ASUS P4B533-X motherboard user guide

1-3

1.3 Special features

1.3.1 Product highlights

Latest processor technology

The motherboard supports the latest Intel

®

Pentium

®

4 or Celeron processor via a

478-pin surface mount ZIF socket. The Pentium 4 processor with 512KB L2 cache on

0.13 micron processor includes a 800*/533/400 MHz system bus, Intel

®

Hyper-

Threading Technology and the FMB2 power design that allows up to 3.06+ GHz

core frequencies for up to 6.4GB/s data transfer rates. (* Overclocking mode) See

page 1-8.

Integrated 10/100 LAN

The onboard LAN controller is a highly integrated Fast Ethernet controller. It is

enhanced with an ACPI management function to provide efficient power

management for advanced operating systems. See page 1-16.

Extreme Overclocking

The motherboard offers robust overclocking options to maximize your system

performance. Overclocking features include: the SFS (Stepless Frequency

Selection) feature, an adjustable FSB/DDR ratio and the ASUS C.P.R. (CPU

Parameter Recall).

6 USB 2.0 ports

The motherboard implements the new Universal Serial Bus (USB) 2.0

specification, extending the connection speed from 12 Mbps on USB 1.1 to a fast

480 Mbps on USB 2.0. The higher bandwidth of USB 2.0 allows connection of

devices such as high resolution video conferencing cameras, next generation

scanners and printers, and fast storage units. USB 2.0 is backward compatible with

USB 1.1. See page 1-19.

6-channel audio

The ADI AD1888 SoundMAX AC ‘97 audio CODEC is onboard to provide 6-

channel audio playback for 5.1 surround sound, over 90dB dynamic range, and

stereo Mic PREAMP. See pages 1-16, 3-3.

S/PDIF out

The motherboard supports S/PDIF out function turns your computer into a high-

end entertainment system with digital connectivity to powerful sound systems. See

page 1-16, 3-3.

1-4

Chapter 1: Product introduction

1.3.2 Unique ASUS features

CrashFree BIOS 2

This feature allows you to restore the original BIOS data from a floppy disk or

support CD in case when the BIOS codes and data are corrupted. This protection

eliminates the need to buy a replacement ROM chip. Page 2-6.

ASUS MyLogo™

This new feature present in the motherboard allows you to personalize and add

style to your system with customizable boot logos. To use the MyLogo feature,

enable the Quick Boot item in the BIOS. See page 3-4.

C.P.R. (CPU Parameter Recall)

The C.P.R. feature of the motherboard BIOS allows automatic re-setting to the

BIOS default settings in case the system hangs due to overclocking. When the

system hangs due to overclocking, C.P.R. eliminates the need to open the system

chassis and clear the RTC data. Simply shut down and reboot the system, and

BIOS automatically restores the CPU’s previous setting for each parameter. See

page 1-14.

ASUS EZ Flash BIOS

With the ASUS EZ Flash, you can easily update the system BIOS even before

loading the operating system. No need to use a DOS-based utility or boot from a

floppy disk. See page 2-5.

ASUS P4B533-X motherboard user guide

1-5

1.4 Before you proceed

Take note of the following precautions before you install motherboard components

or change any motherboard settings.

1. Unplug the power cord from the wall socket before touching any

component.

2. Use a grounded wrist strap or touch a safely grounded object or to a metal

object, such as the power supply case, before handling components to

avoid damaging them due to static electricity.

3. Hold components by the edges to avoid touching the ICs on them.

4. Whenever you uninstall any component, place it on a grounded antistatic

pad or in the bag that came with the component.

5. Before you install or remove any component, ensure that the ATX

power supply is switched off or the power cord is detached from the

power supply. Failure to do so may cause severe damage to the

motherboard, peripherals, and/or components.

Onboard LED

The motherboad comes with a stand-by power LED. When lit, the green LED

indicates that the system is ON, in sleep mode, or in soft-off mode, a reminder that

you should shut down the system and unplug the power cable before removing or

plugging in any motherboard component. The illustration below shows the location

of the onboard LED.

P4B533-X

®

P4B533-X Onboard LED

SB_PWR1

ON

Standby

Power

OFF

Powere

d

Off

1-6

Chapter 1: Product introduction

1.5 Motherboard overview

1.5.1 Motherboard layout

PCI1

PANEL1

P4B533-X

®

CD1

AUX1

Super

I/O

3Mbit

BIOS

Accelerated Graphics Port (AGP)

CPU_FAN1

FP_AUDIO1

GAME1

FLOPPY1

PRI_IDE

SEC_IDE

ATX Power Connector

DDR DIMM1 (64 bit,184-pin module)

CHA_FAN1

SB_PWR1

USB56

CR2032 3V

Lithium Cell

CMOS Power

USBPW34

CLRTC

USBPW56

DDR DIMM2 (64 bit,184-pin module)

USBPW12

Intel

82845E

MCH

AD1888

PS/2KBMS

T: Mouse

B: Keyboard

USB1

USB2

PARALLEL PORT

SPDIF_O

COM1

Below:Mic In

Center:Line Out

Top:Line In

USB2.0

T: USB4

B: USB3

Top:

RJ-45

PCI2

PCI3

PCI4

Intel

82801DE

ICH4

ATX12V1

Socket 478

RTL

8101L

ASUS P4B533-X motherboard user guide

1-7

Do not overtighten the screws! Doing so may damage the motherboard.

1.5.2 Placement direction

When installing the motherboard, make sure that you place it into the chassis in

the correct orientation. The edge with external ports goes to the rear part of the

chassis as indicated in the image below.

1.5.3 Screw holes

Place seven (7) screws into the holes indicated by circles to secure the

motherboard to the chassis.

Place this side towards

the rear of the chassis

1-8

Chapter 1: Product introduction

1.6 Central Processing Unit (CPU)

1.6.1 Overview

The Intel

®

Pentium

®

4 Northwood/Willamette/Prescott processors has a gold

triangular mark on one corner. This mark indicates the processor Pin 1 that should

match a specific corner of the CPU socket.

Incorrect installation of the CPU into the socket may bend the pins and

severely damage the CPU!

P4B533-X

®

P4B533-X Socket 478

Gold Arrow

Notes on Intel

®

Hyper-Threading Technology

1. This motherboard supports Intel

®

Pentium 4 CPUs with Hyper-Threading

Technology. The motherboard automatically detects an installed Intel

Pentium 4 CPU with Hyper-Threading Technology support.

2. To verify the Hyper-Threading feature, go to the Windows OS System

Properties -> Hardware -> Device Manager -> Processors. The list

should display two existing processors.

3. Hyper-Threading Technology is supported under Windows

®

XP™ and later

versions only.

4. It is recommended that you install Windows

®

XP™ Service Pack 1.

5. For more information on Hyper-Threading Technology, visit

www.intel.com/info/hyperthreading.

ASUS P4B533-X motherboard user guide

1-9

1.6.2 Installing the CPU

Follow these steps to install a CPU.

1. Locate the 478-pin ZIF socket on the motherboard.

2. Unlock the socket by pressing the

lever sideways, then lift it up to a 90°-

100° angle.

Make sure that the socket lever is

lifted up to 90°-100° angle,

otherwise the CPU does not fit in

completely.

3. Position the CPU above the socket

such that its marked corner matches

the base of the socket lever.

4. Carefully insert the CPU into the

socket until it fits in place.

The CPU fits only in one correct

orientation. DO NOT force the

CPU into the socket to prevent

bending the pins and damaging

the CPU!

5. When the CPU is in place, push down

the socket lever to secure the CPU.

The lever clicks on the side tab to

indicate that it is locked.

6. Install a CPU heatsink and fan

following the instructions that came

with the heatsink package.

7. Connect the CPU fan cable to the

CPU_FAN1 connector on the

motherboard.

Socket Lever

90 -10

0

Gold Mark

1-10

Chapter 1: Product introduction

Obtain DDR DIMMs only from ASUS qualified vendors. Visit the ASUS website

(www.asus.com) for the latest QVL.

1.7 System memory

1.7.1 DIMM sockets location

The following figure illustrates the location of the DDR DIMM sockets. You may

install 64MB, 128MB, 256MB, 512MB, and 1GB unbuffered DDR DIMMs into this

motherboard.

P4B533-X

®

P4B533-X 184-Pin DDR DIMM Sockets

80 Pins104 Pins

DIMM1

DIMM2

1. Make sure to unplug the power supply before adding or removing DIMMs or

other system components. Failure to do so may cause severe damage to

both the motherboard and the components.

2. When installing long AGP cards, it is recommended to install the memory

modules first. Long AGP cards, when installed, may interfere with the

memory sockets.

It is recommended to populate only one DIMM slot when using

FSB800/DDR400, FSB800/DDR300 and FSB533/DDR355 overlocking

mode features.

Table 1 Memory frequency/CPU FSB synchronization

This motherboard supports different memory frequencies depending on the CPU

FSB (Front Side Bus) and the type of DDR DIMM.

CPU FSB DDR DIMM Type Memory Frequency

800 MHz* PC3200/PC2700* 400/333* MHz

533 MHz PC3200**/PC2700**/PC2100/PC1600 400**/333**/266/200 MHz

400 MHz PC2100/PC1600 266/200 MHz

* When using 800MHz CPU FSB, PC2700 DDR DIMMs run only at 300MHz (not 333MHz)

** When using 533MHz CPU FSB, PC3200/2700 DDR DIMMs may run only at 355MHz/

266MHz (not 400/333MHz) due to chipset limitation.

Page is loading ...

Asus P4B533-X User manual

This manual is also suitable for

Asus P4B533-X User manual

Related papers

Other documents