MODEL: 900011 900012 900013 900014
IMPORTANT SAFETY INSTRUCTIONS:
•
•
•
Important Notice:
QTY Code Part Name QTY Code
0 A
Disc 1 M
0 B
Hex Nut 6 N
3 C
Washer 6 O
1 D
Cup 1 P
2 E
Arm 6 Q
1 F
Light Bulb 0 R
1 G
Cylinder Nut 12 S
1 H
Light Cluster 1 T
1 I
Ground Wire 1 U
2 J
Chain Locker 2 V
1 K
Wire Nut 5 W
1 L
Allen Wrench 1 X
Collar
Chain
Fixture Wire
Loop
Ring
Wire Nut
Mounting Bracket with Nipple
Mounting Screw
Canopy
Hanging Loop
Parts are NOT included for which is shown as 0 under QTY.
PARTS LIST
Part Name
Junction Box
Leading Wires
Light cluster / Arms / Canopy with mounting parts / Chain/ Mounting bracket Parts included in parts bag
ASSEMBLY & INSTALLATION STEPS:
1. Open the box from top, take out all the components, parts bag and manual from the box carefully.
2. Check all the components against the parts list. Make sure get each parts on list. If any parts missing
or glass damage, please contact manufacturer at: [email protected] to get a replacement.
This is a generic instruction sheet used for various fixtures.
The shape and style of fixture / glass / shade / diffuser may vary.
(Required Supply Circuit: 120V, 60Hz. Watt: 12*E26*60W Max) Compatible Bulb Type (NOT Included)
The mostly suggested bulb type is 9W LED ST58 bulb
COMPONENTS INCLUDED IN THE PACKAGE
California, to cause cancer or birth defects or other reproductive harm. For more information,
please go to www.P65Warnings.ca.gov
Caution: Electrician installation highly recommended. All glass is fragile, use care when handling glass
component(s) and or lamp(s). Read instructions carefully and turn electricity off at the main circuit breaker
panel before beginning installation.
Assembly & Installation Instructions
Warning: If any special control devices are used with this fixture, follow the instructions carefully to assure
full compliance with N.E.C. requirements. If there are any questions, please contact a qualified electric
contractor.
Warning: This product can expose you to chemicals including lead, which is known to the State of
Missing parts? Glass damage? Any questions?
Please email us at : [email protected]om
We are always here to help you fix the problems you are facing.
I
II
III
IV
V
VI
VII
VIII
I. S, Q T
II. N, O, P Q
III. K, L, M P
IV. F, G, H, I K
V. E, D A
VI. B, U, J C
VII. H, G, F D
VIII.
R T
Thread the hanging loop (G) onto the nipple of mounting bracket (D) to hang the fixture. Thread the collar (H)
to fix the canopy (F) onto the junction box.
Screw the bulbs (R) on the socket of the light cluster (T).
Illustration of assembly and wiring:
Place the disc (M) and ring (L) on the top of cup (P) through the short nipple, fix with the loop (K).
Thread to open the chain lockers (V) on the ends of the chain (I). Connect one end with loop (K) and fixture,
connect the other end with canopy (F). Wires (J) go through hanging loop (G) and canopy (F) for later wiring.
Install the mounting bracket with nipple (D) to the junction box (A) by the mounting screws (E).
Connect wires according to the wiring diagram on the right.
3. Refer to the illustration while doing assembly and follow the steps as below:
Assemble six arms (Q) to the light cluster (T) and fix with the cylinder nuts (S). Pull the wires gently through
the arms for later wiring with the fixture wires inside the cup (P).
Slide the cup (P) on the arms (Q), then fix with hex nuts (N) and washers (O) using the Allen wrench (X).
Use wire nuts (W) to connect black wires with black, white with white, or according to the wiring diagram.
L
N
D
E
F
G
H
I
K
L
MN
P
Q
R
S
W
J
T
V
V
U
O
/
