VISUAL COMFORT MF 2200 User manual

Brand: VISUAL COMFORT

Model: MF 2200

Type: User manual

VISUAL COMFORT MF 2200 is a single library wall light designed to provide focused illumination for reading or task areas. It features an adjustable arm and shade to direct light precisely where it's needed. Installation requires basic tools and electrical knowledge, including the ability to connect wires and mount the fixture to a junction box. The fixture comes with a mounting plate, screws, and wire nuts for easy installation. It is compatible with standard light bulbs and can be used with a dimmer switch for adjustable brightness.

VISUAL COMFORT MF 2200 is a single library wall light designed to provide focused illumination for reading or task areas. It features an adjustable arm and shade to direct light precisely where it's needed. Installation requires basic tools and electrical knowledge, including the ability to connect wires and mount the fixture to a junction box. The fixture comes with a mounting plate, screws, and wire nuts for easy installation. It is compatible with standard light bulbs and can be used with a dimmer switch for adjustable brightness.

1. Carefully remove all parts from the box. Place on a clean, soft surface.

2. Remove mounting plate (A) from fixture (D) by removing screws (E).

3. Install mounting plate (A) to the junction box and secure with

mounting screws (B).

4. Wrap fixture ground wire (bare copper) around the green grounding

screw (see diagram 1). Tighten. Continue fixture ground wire and

connect to supply ground wire (usually green or bare copper) using

wire nut (C).

NOTE: It is imperative that the fixture is grounded.

5. Connect fixture neutral wire (white) to the supply neutral wire (usually

white) using wire nut (C).

6. Connect fixture hot wire (black) to the supply hot wire (usually

black) using wire nut (C).

CAUTION: Do not reverse the hot and neutral connections.

7. Make sure all wire connections are tight, then carefully tuck into the

junction box.

8. Install fixture (D) to mounting plate (A) and secure with screws (E).

9. Remove socket ring (H) from socket (F).

10. Remove shade (G) from packaging and install to socket (F) by

securing with socket ring (H).

NOTE: If shade has additional packaging, carefully cut off from

interior of shade to avoid damages.

Wimberley Single Library Wall Light

Item # MF 2200

ASSEMBLY INSTRUCTIONS

This light fixture should be installed in accordance with all applicable,

local installation codes, and by a person familiar with the construction

and operation of it, as well as the hazards involved. Inspect item and

contents carefully. If any damage or defect is found, do not install.

Retain all packaging material until installation is complete and approved.

TOOLS REQUIRED (NOT INCLUDED):

Phillips Screwdriver Slotted Screwdriver Scissors

NOTICE:

A

E

C

B

D

J

J

F

G (Packaged separately)

H

Bulb not included

US

M

L

I

D

S

E

T

Diagram 1

Wimberley Single Library Wall Light

Item # MF 2200

ASSEMBLY INSTRUCTIONS

This light fixture should be installed in accordance with all applicable,

local installation codes, and by a person familiar with the construction

and operation of it, as well as the hazards involved. Inspect item and

contents carefully. If any damage or defect is found, do not install.

Retain all packaging material until installation is complete and approved.

11. Loonsen knobs (J) to adjust fixture to desired position, then tighten

knobs (J).

12. Install light bulb into socket.

Care Instructions: Clean only with a soft dry cloth or feather duster. Do

not use abrasive or chemical agents.

NOTICE:

A

E

C

B

D

J

J

F

G (Packaged separately)

H

Bulb not included

Diagram 1

US

M

L

I

D

S

E

T

1
2

VISUAL COMFORT MF 2200 User manual

Brand: VISUAL COMFORT

Model: MF 2200

Type: User manual

VISUAL COMFORT MF 2200 is a single library wall light designed to provide focused illumination for reading or task areas. It features an adjustable arm and shade to direct light precisely where it's needed. Installation requires basic tools and electrical knowledge, including the ability to connect wires and mount the fixture to a junction box. The fixture comes with a mounting plate, screws, and wire nuts for easy installation. It is compatible with standard light bulbs and can be used with a dimmer switch for adjustable brightness.

Download PDF

Related papers

Other documents