Quick Guide
1. Package contains
WIFI DISPLAY * 1 USB power cable * 1
2. Connect
2.1 Please connect to TV with HDMI cable and USB cable. Use a charger no less
than 5V1A if the USB port of TV does not supply enough power. You can
connect to active speaker or AV Monitor with 3.5mm transfer line.
2.2 Select the right TV mode you can see the UI after the dongle power on.
TV
VGA
HDMI
AV1
AV2
Mode: DLNA
Name: MONTOVIEW-123456
Status: Connected to AP
LAN: 192.168.49.1
SSID: ZHIXINGXIN
WAN: 192.168.1.168
USB POWER
AV OUT(OPTION)
HDMI
Active Speaker
AV Monitor
3. Note
：
3.1 Place the dongle in a suitable position and make sure High-quality Wi-Fi
connections can be built between the dongle, your device, Wi-Fi router.
3.2 Please make sure your Wi-Fi router can provide High-quality wireless
performance when your device and dongle connected to the same Wi-Fi
router as bridge to share your screen.
3.3 If the environment is seriously disturbed, change the Wi-Fi channel of your
router and dongle to improve performance. When the dongle connected to
the Wi-Fi router the hotspot of dongle will work at the same channel of the
router.
3.4 The latest version will push to your device when available, keep the dongle
connected to the Internet.
4. Quick guide for iOS
4.1 Short press the MODE key and switch to DLNA mode. The dongle will start to
this mode next time.
4.2 Connect iOS device to the hotspot of dongle ( SSID: MONTOVIEW-XXXXX,
Password: 12345678 ) or your Wi-Fi hotspot ( First use please refer 4.4 and
connect dongle to Wi-Fi router ).
4.3 Control Center > Airplay Mirroring > Choose dongle, TV will share your screen
immediately. Open Airplay Mirroring switch and choose iOS device the screen
share will stop.
4.4 When the first use please set the dongle connected to Wi-Fi router.
Wi-Fi Setup
XXXX
MONTOVIEW
-123456
XXX
XXXXX
Airplay
iPhone
Montoview-1
2345√
Mirroring
AirDrop
AirPlay
4.4.1 Connect your iOS device to the hotspot of dongle ( SSID:
MONTOVIEW-XXXXX, password: 12345678).
4.4.2 Open web browser > Visit 192.168.49.1 > Choose Wi-Fi setup > Select
your Wi-Fi router > Input password > Connect.
4.4.3 After connected successfully, You can see the dongle automatically
shows SSID and IP address assigned from router.
4.5 You can use screen share in two ways.
5. Quick guide for Android
5.1 Short press the MODE key and switch to Miracast mode. The dongle will start
to this mode next time.
5.2 Open Miracast switch on your Android device and choose
MONTOVIEW-XXXXX, the device will automatically connect.
Mode: DLNA
Name: MONTOVIEW-123456
Status: Connected to AP
LAN: 192.168.49.1
SSID: ZHIXINGXIN
WAN: 192.168.1.188
Mode: DLNA M
Name: MONTOVIEW-123456
Status: Disconnected from AP
LAN: 192.168.49.1
SSID:
WAN:
Wi-Fi router
Wi-Fi router
5.3 After the connection is successful, TV will automatically share your screen.
5.4 Miracast only provide screen share between your Android device and dongle.
Please connect your Android device to Wi-Fi router if need Internet service.
5.5 There are different names of Miracast on different Android devices, such as
WIFI Display、WLAN Display、Wireless Display、Allshare Display、Allshare Cast
etc.
5.6 The way to open Miracast switch on different Android devices is different, you
can find it on WLAN、WIFI Setup、Display and so on in the setting menu of
your Android device.
Wireless screen share
Internet service
Available device
MONOVIEW-123456
Press to connect
Setup
WLAN
Display
Screen share
Mode: Miracast Mode
Name: TIDA-123456
Status: Connection in progress…
Device:
MAC:
PORT:
Mode: Miracast Mode
Name: TIDA-123456
Status: Waiting for connection…
Device:
MAC:
PORT:
WIFI hotspot
/
