Rust-Oleum 215214 User guide

Rust-Oleum
Brand
Rust-Oleum
Model
215214
Type
User guide

Rust-Oleum 215214

Rust-Oleum 215214 is a wood filler that can be used to repair cracks, scratches, gouges, and nail holes in wood. It is suitable for use on bare, stained, or finished wood and can be sanded, stained, topcoated, or painted. It dries hard and will not shrink or crack and when cured, it will accept nails and screws.

Before using Rust-Oleum 215214, the surface should be prepared by sanding in the direction of the grain, and removing all sanding dust. Apply the filler directly to the defect and spread it evenly across the surface, pressing firmly in place.

Rust-Oleum 215214

Rust-Oleum 215214 is a wood filler that can be used to repair cracks, scratches, gouges, and nail holes in wood. It is suitable for use on bare, stained, or finished wood and can be sanded, stained, topcoated, or painted. It dries hard and will not shrink or crack and when cured, it will accept nails and screws.

Before using Rust-Oleum 215214, the surface should be prepared by sanding in the direction of the grain, and removing all sanding dust. Apply the filler directly to the defect and spread it evenly across the surface, pressing firmly in place.

TECHNICAL DATA
VAR-14
VARATHANE
®
WOOD FILLER
Form: GDH-617
Rev.: 010417
1
].DESCRIPTION AND USES .
Varathane
®
Wood Filler can be sanded, stained, top-
coated or painted. Apply to defects in wood, including
cracks, scratches, gouges and nail holes. Dries hard and
will not shrink or crack. When cured, it will accept nails
and screws. It can be used on bare, stained, or finished
wood. It is suitable for repairing furniture, cabinets, trim
and even wood floors.
.PRODUCTS .
3.5 oz. Tube Description
215198 Cherry
215199 Fruitwood
215202 Natural
215210 Colonial Maple
215211 Dark Maple
215212 Red Mahogany
215213 Golden Oak
215214 Dark Walnut
.PRODUCT APPLICATION .
SURFACE PREPARATION
Prepare bare wood for staining by sanding in the direction
of the grain. Begin with #120 grit sandpaper and progress
through #150, #180 and #220 grits. Remove all sanding
dust with a vacuum or clean rag dampened with mineral
spirits.
WARNING! If you scrape, sand or remove old paint, you
may release lead dust. LEAD IS TOXIC. EXPOSURE TO
LEAD DUST CAN CAUSE SERIOUS ILLNESS SUCH AS
BRAIN DAMAGE, ESPECIALLY IN CHILDREN.
PREGNANT WOMEN SHOULD ALSO AVOID
EXPOSURE. Wear a NIOSH-approved respirator to
control lead exposure. Clean up carefully with a HEPA
vacuum and a wet mop. Before you start, find out how to
protect yourself and your family by contacting the National
Lead Information Hotline at 1-800-424-LEAD or log on to
www.epa.gov/lead.
PRODUCT APPLICATION (cont.) .
APPLICATION
Stain Application on Bare Wood - Prior to staining bare
wood, ensure filler is completely dry and has been sanded
to a smooth and even finish. Apply stain following
manufacturer’s directions. Allow stain to dry before top
coating. Sand the filler smooth using #240 to #280 grit
sandpaper before staining or top coating.
Application of Wood Filler - Knead tube well before
using. Squeeze out a liberal amount of wood filler directly
in crack or other defect. Using a plastic putty knife, spread
filler evenly across surface and press firmly in place.
Replace lid tightly after each use.
DRY TIME
Dry time of product depends on depth of scratch or repair.
Most repairs will dry within 2 hours. If more than one filling
is required, allow sufficient dry time between coats.
PROTECTING YOUR PROJECT
Use Varathane Polyurethane to protect your project.
TECHNICAL DATA
VARATHANE
®
WOOD FILLER
Rust-Oleum Corporation Form: GDH-617
11 Hawthorn Parkway Phone: 877-385-8155 Rev.: 010417
Vernon Hills, Illinois 60061 www.rustoleum.com
An RPM Company
].PHYSICAL PROPERTIES P
HYSICAL t
WOOD FILLER
Resin Type
Elastomeric Acrylic Emulsion
Pigment Type
Silica
Solvents
Water
Weight
Per Gallon
14.7-15.5 lbs.
Per Liter
1.79-1.85 kg
Solids
By Weight
77.1-80.4%
By Volume
58.0-65.0%
Volatile Organic Compounds
60 g/l
Recommended Dry Film
Thickness (DFT) Per Coat
NA
Wet Film to Achieve DFT
(unthinned material)
NA
Practical Coverage at Recommended
DFT (assumes 15% material loss)
Varies with wood type and depth of scratch or repair.
Dry Times at 70-80°F
(21-27°C) and 50%
Relative Humidity
Touch
1 hour
Handle
1 hour
Recoat
2 hours
Shelf Life
3 years
Flash Point
>200°F (93°C)
Safety Information
For additional information, see SDS
The technical data and suggestions for use contained herein are correct to the best of our knowledge, and offered in good faith. The
statements of this literature do not constitute a warranty, express, or implied, as to the performance of these products. As conditions and use
of our materials are beyond our control, we can guarantee these products only to conform to our standards of quality, and our liability, if any,
will be limited to replacement of defective materials. All technical information is subject to change without notice.
  • Page 1 1
  • Page 2 2

Rust-Oleum 215214 User guide

Rust-Oleum
Brand
Rust-Oleum
Model
215214
Type
User guide

Rust-Oleum 215214

Rust-Oleum 215214 is a wood filler that can be used to repair cracks, scratches, gouges, and nail holes in wood. It is suitable for use on bare, stained, or finished wood and can be sanded, stained, topcoated, or painted. It dries hard and will not shrink or crack and when cured, it will accept nails and screws.

Before using Rust-Oleum 215214, the surface should be prepared by sanding in the direction of the grain, and removing all sanding dust. Apply the filler directly to the defect and spread it evenly across the surface, pressing firmly in place.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents