2. Golden Lighting
  3. 1208-1W DNI

Golden Lighting 1208-1W DNI Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Golden Lighting 1208-1W DNI Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Assembly Instructions: 1208-1W DNI (Marcellis)
IMPORTANT:
• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.
• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!
• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!
PREPARING FOR INSTALLATION
Remove all of the contents from the carton. See the important notes
above. Shut off the power at the circuit breaker and completely
removetheoldxturefromthewall,includingtheoldmounting
strap.
Mountingstrap(B)containsseveralpairsofthreadedholes.Findthe
pairofholesthatmatchesthespacingoftheholesonthejunction
boxandyourxturebackplate.Twoofmountingscrews(A)should
beattachedtomountingstrap(B).Youmayneedtotightenthe
nutsthatholdthesescrewsinplace.Pullthehousewiresthrough
thecenterofmountingstrap(B).Placemountingstrap(B)over
thejunctionboxsothatmountingscrews(A)arehorizontal,andin
alignmentwiththeholelocationsonthexturebackplate(F).Secure
mountingstrap(B)tothejunctionboxwithmountingscrews(D)and
ascrewdriver.Tightenthescrewssecurely.
CONNECTING THE WIRES
Attachthexture’swirestothepowersupplywiresfromthejunction
box.Connectblacktoblack(orsmooth);whitetowhite(orribbed);
groundtoground(greenorcopper).Twisttheendsofthewirepairs
together,thentwistonawireconnector.Makesurealltwistsarein
thesamedirection.Ifthereisnogroundwire(greenorcopper)from
thejunctionbox,locategroundscrew(E)onmountingstrap(B)and
wrapthexturegroundwirearoundthegreengroundscrew(E).Use
ascrewdrivertosecuregroundscrew(E)ontothemountingbracket.
Tuckallwiresneatlyintothejunctionbox.
FINISHING THE INSTALLATION
Placexturebackplate(F)overmountingscrews(A)sothatthey
protrudethroughtheholesinthefrontofthebackplate.Thread
deconuts(G)ontomountingscrews(A).Twistuntilbackplate(F)of
thextureissnugagainstthewall.
Note: Completetheremainingstepsafterthextureishung.
Tightenthedecorativehammerednials(I)ontothethreadsatthe
bottomofthexturearm.
Carefullyslideglassshade(K)oversocket(H).Candlesleeve(L)
haveretainingringsattached.Theretainingringhastwosmall
holesineachside.Theglassshadeopeningistight.Carefullypush
thecandlesleevedownintotheglassshadeandoverthesocket.
Carefully place the tips of socket tool (J) into the holes in the
retainingring.Usesockettool(J)tothreadtheretainingringsonto
thesocketthreads.Thiswillsecuretheglassinplace.
Installlightbulbsinaccordancewiththexture’sspecications.Do
notexceedthemaximumrecommendedwattage.
Your installation is now complete. Turn on the power and test the
xture.
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.
For Customer Service, contact
the place of purchase to arrange
for replacement parts.
BD
C
G
J
K
L
H
I
A
E
F
BLACK
(Hot)
WHITE
(Neutral)
GREEN
(Ground)
HOUSE WIRES
SMOOTH
(Or Black)
FIXTURE WIRES
RIBBED
(Or White)
BARE COPPER
(Or Green)
/