Toro TimeCutter Z530 Riding Mower User manual

Brand: Toro

Model: TimeCutter Z530 Riding Mower

Category: Lawnmowers

Type: User manual

Form No. 3354-901 Rev A

TimeCutter® Z530 Riding

Mowers

Model No. 74425 —Serial No. 260000001 and Up

T his spark ignition system complies with Canadian

ICES-002

Introduction

R ead this infor mation carefully to lear n ho w to

operate and maintain y our product properly and

to a v oid injur y and product damag e . Y ou are

responsible for operating the product properly

and safely .

Y ou ma y contact T oro directly at www .T oro .com

for product and accessor y infor mation, help

ﬁnding a dealer , or to register y our product.

W henev er y ou need ser vice , g en uine T oro par ts ,

or additional infor mation, contact an A uthorized

Ser vice Dealer or T oro Customer Ser vice and ha v e

the model and serial n umbers of y our product

ready . Figure 1 identiﬁes the location of the model

and serial n umbers on the product. W rite the

n umbers in the space pro vided.

Figure 1

1. Model and serial number plate

W rite the product model and serial n umbers in the

space belo w:

Model No.

Serial No.

T his man ual identiﬁes potential hazards and has

safety messag es identiﬁed b y the safety aler t

symbol ( Figure 2 ), whic h signals a hazard that ma y

cause serious injur y or death if y ou do not follo w

the recommended precautions .

Figure 2

1. Safety alert symbol.

T his man ual uses tw o other w ords to highlight

infor mation. Impor tant calls attention to special

mec hanical infor mation and Note emphasizes

g eneral infor mation w or th y of special attention.

Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Safe Operation Practices for

Ride-on (riding)

R otar y La wnmo w er

Mac hines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Safe Operating Practices . . . . . . . . . . . . . . . . . . . . . . 4

T oro Riding Mo w er Safety . . . . . . . . . . . . . . . . . . . 5

Sound Pressure for

Model 74425 . . . . . . . . . . . . . . . . . . . . . . . 6

Sound P o w er for Model 74425 . . . . . . . . . . . . . 6

Vibration for Model 74425 . . . . . . . . . . . . . . . . . . . 6

Safety and Instr uctional Decals . . . . . . . . . . . . 7

Product Ov er view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

T hink Safety First . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

R ecommended Gasoline . . . . . . . . . . . . . . . . . . . . 12

Chec king the Engine Oil Lev el . . . . . . . . . . . 13

Star ting and Stopping the

Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Operating the Blades . . . . . . . . . . . . . . . . . . . . . . . . . 14

T he Safety Interloc k System . . . . . . . . . . . . . . . 15

Dri ving F orw ard or Bac kw ard . . . . . . . . . . . . 15

Stopping the Mac hine . . . . . . . . . . . . . . . . . . . . . . . . 16

Adjusting the Height of Cut . . . . . . . . . . . . . . . 16

P ositioning the Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Adjusting the Motion Control

Lev ers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Pushing the Mac hine b y Hand . . . . . . . . . . . . 17

Adjusting the F ootrest . . . . . . . . . . . . . . . . . . . . . . . 18

Side Disc harg e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Operating Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

R ecommended Maintenance

Sc hedule(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Premaintenance Procedures . . . . . . . . . . . . . . . . . . . . . . . 21

8111 Lyndale Avenue South

Bloomington, MN 55420

Printed in the USA.

R emo ving and Installing the

Engine Hood . . . . . . . . . . . . . . . . . . . . . 21

Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Greasing the Bearings . . . . . . . . . . . . . . . . . . . . . . . . 21

Engine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Ser vicing the Air Cleaner . . . . . . . . . . . . . . . . . . . 21

Ser vicing the Engine Oil . . . . . . . . . . . . . . . . . . . . 23

Ser vicing the Spark Plug . . . . . . . . . . . . . . . . . . . . 25

Fuel System Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Draining the Fuel T ank . . . . . . . . . . . . . . . . . . . . . . 26

R e placing the Fuel Filter . . . . . . . . . . . . . . . . . . . . 26

Electrical System Maintenance . . . . . . . . . . . . . . . . . . . 27

Ser vicing the Batter y . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Ser vicing the Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Dri v e System Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . 29

Chec king the Tire Pressure . . . . . . . . . . . . . . . . . 29

Mo w er Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Ser vicing the Cutting Blades . . . . . . . . . . . . . . . 30

Lev eling the Mo w er from

Side-to-Side . . . . . . . . . . . . . . . . . . . . . . . 31

Adjusting the F ront-to-R ear Blade

Slope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

R emo ving the Mo w er . . . . . . . . . . . . . . . . . . . . . . . . 33

Mo w er Belt Maintenance . . . . . . . . . . . . . . . . . . . 34

Installing the Mo w er . . . . . . . . . . . . . . . . . . . . . . . . . . 35

R e placing the Grass Deﬂector . . . . . . . . . . . . 35

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

W ashing the Underside of the

Mo w er . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Storag e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Cleaning and Storag e . . . . . . . . . . . . . . . . . . . . . . . . . 37

T roubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Sc hematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Safety

Safe Operation Practices

for Ride-on (riding) Rotary

Lawnmower Machines

T his mac hine meets or ex ceeds European

Standards in effect at the time of production.

Ho w ev er , improper use or maintenance b y the

operator or o wner can result in injur y . T o reduce

the potential for injur y , comply with these safety

instr uctions and alw a ys pa y attention to the

safety aler t symbol, whic h means CA UTION ,

W ARNING , or D ANGER -“personal safety

instr uction. ” F ailure to comply with the instr uction

ma y result in personal injur y or death.

Safe Operating Practices

T he follo wing instr uctions are from the CEN

standard EN 836:1997.

T his product is capable of amputating hands and

feet and thro wing objects . Alw a ys follo w all safety

instr uctions to a v oid serious injur y or death.

Training

• R ead the instr uctions carefully . Be familiar

with the controls and the proper use of the

equipment.

• Nev er allo w c hildren or people unfamiliar with

these instr uctions to use the la wnmo w er . Local

regulations can restrict the ag e of the operator .

• Nev er mo w while people , especially c hildren,

or pets are nearb y .

• K ee p in mind that the operator or user is

responsible for accidents or hazards occur ring

to other people or their proper ty .

• Do not car r y passeng ers .

• All dri v ers should seek and obtain professional

and practical instr uction. Suc h instr uction

should emphasize:

– the need for care and concentration when

w orking with ride-on mac hines;

– control of a ride-on mac hine sliding on a

slope will not be reg ained b y the application

of the brak e . T he main reasons for loss of

control are:

◊ insufﬁcient wheel g rip;

◊ being dri v en too fast;

◊ inadequate braking;

◊ the type of mac hine is unsuitable for its

task;

◊ lac k of a w areness of the effect of

g round conditions , especially slopes;

◊ incor rect hitc hing and load distribution.

Preparation

• W hile mo wing, alw a ys w ear substantial

footw ear and long trousers . Do not operate

the equipment when barefoot or w earing open

sandals .

• T horoughly inspect the area where the

equipment is to be used and remo v e all objects

whic h ma y be thro wn b y the mac hine .

• W ar ning-Fuel is highly ﬂammable .

– Store fuel in containers speciﬁcally designed

for this pur pose .

– R efuel outdoors only and do not smok e

while refuelling .

– Add fuel before star ting the engine . Nev er

remo v e the cap of the fuel tank or add fuel

while the engine is r unning or when the

engine is hot.

– If fuel is spilled, do not attempt to star t the

engine but mo v e the mac hine a w a y from

the area of spillag e and a v oid creating any

source of ignition until fuel v apors ha v e

dissipated.

– R e place all fuel tanks and container caps

securely .

• R e place faulty silencers .

• Before using, alw a ys visually inspect to see that

the blades , blade bolts and cutter assembly

are not w or n or damag ed. R e place w or n or

damag ed blades and bolts in sets to preser v e

balance .

• On m ulti-bladed mac hines , tak e care as rotating

one blade can cause other blades to rotate .

Operation

• Be aler t, slo w do wn and use caution when

making tur ns . Look behind and to the side

before c hanging directions .

• Do not operate the engine in a conﬁned space

where dang erous carbon mono xide fumes can

collect.

• Mo w only in da ylight or in g ood ar tiﬁcial light.

• Before attempting to star t the engine ,

diseng ag e all blade attac hment clutc hes and

shift into neutral.

• Do not use on slopes of more than 12-1/2

deg rees .

• R emember there is no suc h thing as a safe

slope . T ra v el on g rass slopes requires par ticular

care . T o guard ag ainst o v er tur ning:

– do not stop or star t suddenly when g oing

up or do wnhill;

– use lo w speeds on slopes and during tight

tur ns;

– sta y aler t for humps and hollo ws and other

hidden hazards;

• Use care when pulling loads .

– Use only appro v ed dra wbar hitc h points .

– Limit loads to those y ou can safely control.

– Do not tur n shar ply . Use care when

rev ersing .

• W atc h out for trafﬁc when crossing or near

roadw a ys .

• Stop the blades rotating before crossing

surfaces other than g rass .

• W hen using any attac hments , nev er direct

disc harg e of material to w ard b ystanders

nor allo w any one near the mac hine while in

operation.

• Nev er operate the mac hine with damag ed

guards or without safety protecti v e devices in

place .

• Do not c hang e the engine g o v er nor settings or

o v erspeed the engine . Operating the engine

at ex cessi v e speed can increase the hazard of

personal injur y .

• Before lea ving the operator’ s position:

– diseng ag e the po w er tak e-off and lo w er the

attac hments;

– c hang e into neutral and set the parking

brak e;

– stop the engine and remo v e the k ey .

• Diseng ag e dri v e to attac hments , stop the

engine , and disconnect the spark plug wire(s)

or remo v e the ignition k ey

– before clearing bloc kag es or unclog ging

c hute;

– before c hec king, cleaning or w orking on

the la wnmo w er;

– after striking a foreign object. Inspect

the la wnmo w er for damag e and mak e

re pairs before restar ting and operating the

equipment;

– if the mac hine star ts to vibrate abnor mally

(c hec k immediately).

• Diseng ag e dri v e to attac hments when

transpor ting or not in use .

• Stop the engine and diseng ag e dri v e to

attac hment

– before refuelling;

– before remo ving the g rass catc her;

– before making height adjustment unless

adjustment can be made from the operator’ s

position.

• R educe the throttle setting during engine

r un-out and, if the engine is pro vided with

a shut-off v alv e , tur n the fuel off at the

conclusion of mo wing .

Maintenance and Storage

• K ee p all n uts , bolts and screws tight to be sure

the equipment is in safe w orking condition.

• Nev er store the equipment with fuel in the

tank inside a building where fumes can reac h

an open ﬂame or spark.

• Allo w the engine to cool before storing in any

enclosure .

• T o reduce the ﬁre hazard, k ee p the engine ,

silencer , batter y compar tment and fuel storag e

area free of g rass , lea v es , or ex cessi v e g rease .

• Chec k the g rass catc her frequently for w ear or

deterioration.

• R e place w or n or damag ed par ts for safety .

• If the fuel tank has to be drained, this should

be done outdoors .

• W hen mac hine is to be park ed, stored or left

unattended, lo w er the cutting means .

Toro Riding Mower Safety

T he follo wing list contains safety infor mation

speciﬁc to T oro products or other safety

infor mation that y ou m ust kno w that is not

included in the CEN standard.

• Engine exhaust contains carbon mono xide ,

whic h is an odorless , deadly poison that can

kill y ou. Do not r un engine indoors or in an

enclosed area.

• K ee p hands , feet, hair and loose clothing a w a y

from attac hment disc harg e area, underside of

mo w er and any mo ving par ts while engine is

r unning .

• Do not touc h equipment or attac hment par ts

whic h ma y be hot from operation. Allo w to

cool before attempting to maintain, adjust, or

ser vice .

• Batter y acid is poisonous and can cause bur ns .

A v oid contact with skin, eyes and clothing .

Protect y our face , eyes , and clothing when

w orking with a batter y .

• Batter y g ases can explode . K ee p cig arettes ,

sparks , and ﬂames a w a y from batter y .

• Use only g en uine T oro re placement par ts to

ensure that original standards are maintained.

• Use only T oro-appro v ed attac hments .

Slope Operation

• Do not mo w slopes g reater than 12-1/2

deg rees .

• Do not mo w near drop-offs , ditc hes , stee p

banks , or w ater . W heels dropping o v er edg es

can cause rollo v ers , whic h ma y result in serious

injur y , death, or dro wning .

• Do not mo w slopes when g rass is w et. Slipper y

conditions reduce traction and could cause

sliding and loss of control.

• Do not mak e sudden tur ns or rapid speed

c hang es .

• Use a w alk behind mo w er and/or a hand

trimmer near drop-offs , ditc hes , stee p banks ,

or w ater .

• R educe speed and use extreme caution on

slopes .

• R emo v e or mark obstacles suc h as roc ks , tree

limbs , etc . from mo wing area. T all g rass can

hide obstacles .

• W atc h for ditc hes , holes , roc ks dips , and rises

that c hang e the operating angle , as rough

ter rain could o v er tur n the mac hine .

• A v oid sudden star ts when mo wing uphill

because the mo w er ma y tip bac kw ards .

• Be a w are that loss of traction ma y occur g oing

do wnhill. W eight transfer to the front wheels

ma y cause dri v e wheels to slip and cause loss

of braking and steering .

• Alw a ys a v oid sudden star ting or stopping on

a slope . If tires lose traction, diseng ag e the

blades and proceed slo wly off the slope .

• F ollo w the man ufacturer’ s recommendations

for wheel w eights or counterw eights to

impro v e stability .

• Use extreme care with g rass catc hers or other

attac hments . T hese can c hang e the stability of

the mac hine and cause loss of control.

Sound Pressure for

Model 74425

T his unit has a maxim um sound pressure lev el

at the operator’ s ear of 87 dB A, based on

measurements of identical mac hines per Directi v e

98/37/EC .

Sound Power for

Model 74425

T his unit has a guaranteed sound po w er lev el of

100 dB A, based on measurements of identical

mac hines per Directi v e 2000/14/EC .

Vibration for Model 74425

T his unit does not ex ceed a hand/ar m vibration

lev el of 4.66 m/s

, based on measurements of

identical mac hines per Directi v e 98/37/EC .

T his unit does not ex ceed a whole body vibration

lev el of .14 m/s

, based on measurements of

identical mac hines per Directi v e 98/37/EC .

Safety and Instructional

Decals

Safety decals and instr uctions are easily visible to the operator and are located near any

area of potential dang er . R e place any decal that is damag ed or lost.

93-6677

1. Warning—don’t operate the mower with the deector up or

removed; keep the deector in place.

2. Cutting/dismemberment hazard of hand or foot, mower

blade—stay away from moving parts.

93-7009

1. Warning—don’t operate the mower with the deector up or

removed; keep the deector in place.

2. Cutting/dismemberment hazard of hand or foot, mower

blade—stay away from moving parts.

93-7010

1. Thrown object hazard—keep bystanders a safe distance from

the machine.

2. Thrown object hazard, mower—keep the deector in place.

3. Cutting/dismemberment of hand or foot—stay away from

moving parts.

Manufacturer’s Mark

1. Indicates the blade is identied as a part from the original

machine manufacturer.

110-1868

1. Thrown object hazard, mower—keep the deector in place.

2. Thrown object hazard—Keep bystanders a safe distance from

the machine; Do not operate the without grass collection

system in place.

3. Cutting/dismemberment of hand or foot—stay away from

moving parts.

105-7015

106-2223

106-2224

1. Throttle 7. Headlights

2. Choke

8. Engine—stop

3. Fast

9. Engine—run

4. Continuous variable setting

10. Engine—start

5. Slow

11. Ignition

6. Power take-off (PTO), Blade

control switch on some

models

108-6109

1. To push the machine, move tow levers forward and then

out to lock them into position.

106-8717

1. Read the instructions before servicing or performing

maintenance.

2. Check tire pressure every 25 operating hours.

3. Grease every 25 operating hours.

4. Engine

106-8742

1. Parking brake

106-8743

1. Height of cut

Battery Symbols

Some or all of these symbols are on your battery

1. Explosion hazard 6. Keep bystanders a safe

distance from the battery.

2. No re, open ame, or

smoking.

7. Wear eye protection;

explosive gases can cause

blindness and other injuries

3. Caustic liquid/chemical

burn hazard

8. Battery acid can cause

blindness or severe burns.

4. Wear eye protection

9. Flush eyes immediately

with water and get medical

help fast.

5. Read the Operator’s

Manual.

10. Contains lead; do not

discard.

107-2514

1. Warning—read the instructions before servicing or performing maintenance; move the levers out to set the parking brake and

remove the ignition key before leaving the machine.

2. Warning—read the Operator’s Manual .

3. Thrown object hazard, mower—keep the deector in place.

4. Tipping hazard, slopes greater than 12.5 degrees—do not drive the machine on a slope greater than 12.5 degrees.

5. Thrown object hazard—keep bystanders a safe distance from the machine and pick up debris before operating.

6. Crushing/dismemberment hazard of bystanders—do not carry passengers.

7. Cutting/dismemberment hazard of hand or foot, mower blade—stay away from moving parts.

Product Overview

Figure 3

1. Seat

4. Height of cut lever 7. Front caster wheel 10. Anti-scalp roller

2. Control levers 5. Mower deck 8. Rear drive wheel

3. Control panel

6. Footrest

9. Cup holder

Controls

Become familiar with all of the controls Figure 5

and Figure 4 before y ou star t the engine and

operate the mac hine .

Figure 4

1. Motion control lever 3. Gas tank cap

2. Height-of-cut lever

Figure 5

1. Ignition switch 3. Blade control switch

(power take-off)

2. Throttle/Choke

Parking Brake

T he parking brak e is automatically set when the

motion control lev ers are in the brak e position.

Alw a ys position the motion control lev ers into the

brak e position when y ou stop the mac hine or lea v e

it unattended.

Operation

Note: Deter mine the left and right sides of the

mac hine from the nor mal operating position.

Think Safety First

Please carefully read all of the safety instr uctions

and decals in the safety section. Kno wing this

infor mation could help y ou, y our family , pets or

b ystanders a v oid injur y .

Mo wing on w et g rass or steep slopes can

cause sliding and loss of contr ol.

W heels dr opping o v er edges can cause

r ollo v er s, which may r esult in serious injur y ,

death or dr o wning .

T o a v oid loss of contr ol and possibility of

r ollo v er :

• Do not mo w near dr op-of fs or near w ater .

• Do not mo w slopes g r eater than

12.5 deg r ees.

• R educe speed and use extr eme caution

on slopes.

• A v oid sudden tur ns or rapid speed

changes.

Figure 6

1. Safe Zone-use the TimeCutter here

2. Use walk behind mower and/or hand trimmer near drop-offs

and water.

3. Water

Recommended Gasoline

Use UNLEADED R egular Gasoline suitable

for automoti v e use (87 pump octane minim um).

Leaded regular g asoline ma y be used if unleaded

regular is not a v ailable .

Important: Nev er use methanol, gasoline

containing methanol, or gasohol containing

mor e than 10% ethanol because the fuel

system could be dama ged. Do not mix oil

with gasoline.

In cer tain conditions, gasoline is extr emel y

ﬂamma ble and highl y explosi v e. A ﬁr e or

explosion fr om gasoline can bur n y ou and

other s and can dama ge pr oper ty .

• Fill the fuel tank outdoor s, in an open

ar ea, when the engine is cold. W ipe up

an y gasoline that spills.

• Nev er ﬁll the fuel tank inside an enclosed

trailer .

• Do not ﬁll the fuel tank completel y full.

Add gasoline to the fuel tank until the

lev el is 1/4 to 1/2 inch (6 to 13 mm)

belo w the bottom of the ﬁller neck. T his

empty space in the tank allo ws gasoline

to expand.

• Nev er smok e when handling gasoline,

and stay a w ay fr om an open ﬂame or

wher e gasoline fumes may be ignited by

a spar k.

• Stor e gasoline in an appr o v ed container

and k eep it out of the r each of childr en.

Nev er buy mor e than a 30-day suppl y of

gasoline.

• Do not operate without entir e exhaust

system in place and in pr oper w or king

condition.

In cer tain conditions during fueling , static

electricity can be r eleased causing a spar k

which can ignite the gasoline v apor s. A ﬁr e

or explosion fr om gasoline can bur n y ou and

other s and can dama ge pr oper ty .

• Al w ays place gasoline container s on the

g r ound a w ay fr om y our v ehicle bef or e

ﬁlling .

• Do not ﬁll gasoline container s inside

a v ehicle or on a tr uck or trailer bed

because interior car pets or plastic tr uck

bed liner s may insulate the container and

slo w the loss of an y static charge.

• W hen practical, r emo v e gas-po w er ed

equipment fr om the tr uck or trailer and

r efuel the equipment with its wheels on

the g r ound.

• If this is not possible, then r efuel such

equipment on a tr uck or trailer fr om a

por ta ble container , rather than fr om a

gasoline dispenser nozzle.

• If a gasoline dispenser nozzle must be

used, k eep the nozzle in contact with the

rim of the fuel tank or container opening

at all times until fueling is complete.

Gasoline is har mful or f atal if s w allo w ed.

Long-ter m exposur e to v apor s can cause

serious injur y and illness.

• A v oid pr olonged br eathing of v apor s.

• K eep f ace a w ay fr om nozzle and gas tank

or conditioner opening .

• K eep gas a w ay fr om ey es and skin.

Using Stabilizer/Conditioner

Use a fuel stabilizer/conditioner in the mac hine to

pro vide the follo wing beneﬁts:

• K ee ps g asoline fresh during storag e of 90 da ys

or less . F or long er storag e it is recommended

that the fuel tank be drained.

• Cleans the engine while it r uns

• Eliminates gum-lik e v ar nish buildup in the fuel

system, whic h causes hard star ting

Important: Do not use fuel additi v es

containing methanol or ethanol.

Add the cor rect amount of g as

stabilizer/conditioner to the g as .

Note: A fuel stabilizer/conditioner is most

effecti v e when mix ed with fresh g asoline . T o

minimize the c hance of v ar nish de posits in the fuel

system, use fuel stabilizer at all times .

Filling the Fuel Tank

1. Shut the engine off and set the parking brak e .

2. Clean around the fuel tank cap and remo v e

the cap . Add unleaded regular g asoline to the

fuel tank until the lev el is 1/4 to 1/2 inc h

(6 to 13 mm) belo w the bottom of the ﬁller

nec k. T his space in the tank allo ws g asoline to

expand. Do not ﬁll the fuel tank completely

full.

3. Install the fuel tank cap securely . Wipe up any

g asoline that ma y ha v e spilled.

Checking the Engine Oil

Level

Before y ou star t the engine and use the mac hine ,

c hec k the oil lev el in the engine crankcase; refer to

Chec king the Oil Lev el in Engine Maintenance ,

pag e 21 .

Starting and Stopping the

Engine

Starting the Engine

1. Sit do wn on the seat and mo v e the motion

controls to the brak e position.

2. Diseng ag e the blades b y mo ving the blade

control switc h to Off ( Figure 7 ).

Figure 7

1. Blade control switch—On 2. Blade control switch—Off

3. Mo v e the throttle lev er to Chok e before

star ting a cold engine ( Figure 8 ).

Note: A w ar m or hot engine ma y not require

c hoking .

4. T ur n the ignition k ey to Star t to energize the

star ter . W hen the engine star ts , release the k ey .

Important: Do not enga ge the star ter

f or mor e than 10 seconds at a time. If the

engine f ails to star t, allo w a 60 second

cool-do wn period betw een attempts.

F ailur e to f ollo w these instr uctions can

bur n out the star ter motor .

5. After the engine star ts , mo v e the throttle

lev er to F ast ( Figure 8 ). If the engine stalls

or hesitates , mo v e the throttle lev er bac k to

Chok e for a few seconds . T hen mo v e the

throttle lev er to the desired setting . R e peat this

as required.

Figure 8

1. Engine

3. Fast

2. Choke 4. Slow

Figure 9

1. Off

3. Start

2. Run

4. Ignition

Stopping the Engine

1. Mo v e the throttle lev er to F ast ( Figure 8 ).

2. Diseng ag e the blades b y mo ving the blade

control switc h to Off ( Figure 7 ).

3. T ur n the ignition k ey to Off ( Figure 9 ).

4. Pull the wire off of the spark plug(s) to prev ent

the possibility of someone accidentally star ting

the mac hine before transpor ting or storing the

mac hine .

5. Close the fuel shut-off v alv e under the front

of the fuel tank before transpor ting or storing

the mac hine .

Important: Mak e sur e the fuel shut-of f

v alv e is closed bef or e transpor ting or

storing the machine, as fuel leaka ge may

occur .

Operating the Blades

T he blade control switc h, re presented b y a po w er

tak e-off (PTO) symbol, eng ag es and diseng ag es

po w er to the mo w er blades . T his switc h controls

po w er to any attac hments that dra w po w er from

the engine , including the mo w er dec k and cutting

blades .

Engaging the Blades

1. R elease pressure on the traction control lev ers

and place the mac hine in neutral.

2. Mo v e the throttle to the F ast position.

3. Pull out on the blade control switc h to eng ag e

blades ( Figure 10 ).

Figure 10

1. Blade control switch-On 2. Blade control switch-Off

Disengaging the Blades

Push the blade control switc h to Off to diseng ag e

the blades ( Figure 10 ).

The Safety Interlock System

If safety inter lock s witches ar e disconnected

or dama ged the machine could operate

unexpectedl y causing per sonal injur y .

• Do not tamper with the inter lock

s witches.

• Check the operation of the inter lock

s witches dail y and r eplace an y dama ged

s witches bef or e operating the machine.

Understanding the Safety Interlock

System

T he safety interloc k system is designed to prev ent

the engine from star ting unless:

• T he blades are diseng ag ed.

• T he motion control lev ers are in the brak e

position.

T he safety interloc k system also is designed to stop

the engine when the control lev ers are out of the

brak e position and y ou rise from the seat when

the blades are eng ag ed.

Testing the Safety Interlock System

T est the safety interloc k system before y ou use

the mac hine eac h time . If the safety system

does not operate as described belo w , ha v e an

A uthorized Ser vice Dealer re pair the safety system

immediately .

1. W hile sitting on the seat, with the control

lev ers in brak e position, and mo v e the blade

control switc h to On. T r y star ting the engine;

the engine should not crank.

2. W hile sitting on the seat, mo v e the blade

control switc h to Off . Mo v e either motion

control lev er to the center , unloc k ed position.

T r y star ting the engine; the engine should not

crank. R e peat with the other motion control

lev er .

3. W hile sitting on the seat, mo v e the blade

control switc h to Off , and loc k the motion

control lev ers in neutral. Star t the engine .

W hile the engine is r unning, eng ag e the blade

control switc h, and rise slightly from the seat;

the engine should stop .

4. W hile sitting on the seat, mo v e the blade

control switc h to Off , and loc k the motion

control lev ers in neutral. Star t the engine .

W hile the engine is r unning, mo v e the motion

control lev ers to the center , unloc k ed position,

eng ag e the blade control switc h, and rise

slightly from the seat; the engine should stop .

Driving Forward or

Backward

T he throttle control regulates the engine speed as

measured in r pm (rev olutions per min ute). Place

the throttle control in the F ast position for best

perfor mance . Alw a ys operate in the full throttle

position.

T he machine can spin v er y rapidl y . T he

operator may lose contr ol of the machine

and cause per sonal injur y or dama ge to the

machine.

• Use caution when making tur ns.

• Slo w the machine do wn bef or e making

shar p tur ns.

Forward

1. Mo v e the lev ers to the center , unloc k ed

position.

2. T o g o forw ard, slo wly push the motion control

lev ers forw ard ( Figure 11 ).

Figure 11

1. Center unlock position 3. Backward

2. Forward 4. Brake position

T o g o straight, apply equal pressure to both

motion control lev ers ( Figure 11 ).

T o tur n, release pressure on the motion control

lev er to w ard the direction y ou w ant to tur n

( Figure 11 ).

T he far ther y ou mo v e the traction control

lev ers in either direction, the faster the mac hine

will mo v e in that direction.

T o stop , pull the motion control lev ers to

neutral.

Backward

1. Mo v e the lev ers to the center , unloc k ed

position.

2. T o g o bac kw ard, slo wly pull the motion control

lev ers rearw ard ( Figure 11 ).

T o g o straight, apply equal pressure to both

motion control lev ers ( Figure 11 ).

T o tur n, release the pressure on the motion

control lev er to w ard the direction y ou w ant to

tur n ( Figure 11 ).

T o stop , push the motion control lev ers to

neutral.

Stopping the Machine

T o stop the mac hine , mo v e the traction control

lev ers to neutral and se parate to the brak e position,

diseng ag e the blade control switc h, ensure the

throttle is in the fast position, and tur n the ignition

k ey to off . R emember to remo v e the k ey from the

ignition switc h.

Childr en or bystander s may be injur ed if

they mo v e or attempt to operate the mo w er

while it is unattended.

Al w ays r emo v e the ignition k ey and mo v e the

motion contr ol lev er s to the brak e position

when lea ving the machine unattended, ev en

if just f or a few min utes.

Adjusting the Height of Cut

T he height of cut is adjusted from 1-1/2 to

4-1/2 inc h (38 to 114 mm) in 1/2 inc h (13 mm)

increments b y mo ving the height-of-cut lev er in

different locations .

1. Raise the height-of-cut lev er to the transpor t

position (also the 4-1/2 inc h (114 mm) cutting

height position ( Figure 12 ).

2. T o adjust, pull up on the height-of-cut lev er

and mo v e it to the desired position ( Figure 12 ).

Figure 12

1. Height-of-cut lever 2. Height-of-cut positions

Positioning the Seat

T he seat can mo v e forw ard and bac kw ard.

P osition the seat where y ou ha v e the best control

of the mac hine and are most comfor table .

1. Raise the seat and loosen the adjustment knobs

enough to mo v e the seat ( Figure 13 ).

Important: Mak e sur e that the spacer s

stay in place when loosening the knobs

to mo v e the seat. Loss of the spacer s can

r esult in dama ge to the seat.

2. Mo v e the seat to the desired position and

tighten the knobs .

Figure 13

1. Adjustment knobs

Adjusting the Motion

Control Levers

T he motion control lev ers can be adjusted higher

or lo w er for maxim um operator comfor t.

1. R emo v e the 2 bolts holding the control lev er

to the control ar m shaft ( Figure 14 ).

2. Mo v e the control lev er to the next set of holes .

Secure the lev er with the 2 bolts ( Figure 14 ).

Figure 14

1. Control lever 3. Control arm shaft

2. Bolt

3. R e peat the adjustment for the opposite control

lev er .

Pushing the Machine by

Hand

Important: Al w ays push the machine

by hand. Nev er to w the machine because

dama ge may occur .

To Push the Machine

1. P ark the mac hine on a lev el surface and

diseng ag e the blade control switc h.

2. Mo v e the motion control lev ers outw ard to

eng ag e the parking brak e , stop the engine ,

remo v e the k ey , and w ait for all mo ving par ts

to stop before lea ving the operating position.

3. Raise the seat to access the b ypass lev ers

( Figure 15 ).

4. Mo v e the tw o b ypass lev ers forw ard and then

outw ard to loc k them in place as sho wn in

Figure 15 .

5. Mo v e the motion control lev ers inw ard to

diseng ag e the parking brak e .

T he mac hine is no w able to be pushed b y hand.

Figure 15

1. Bypass levers 3. Lever position for operating

the machine

2. Lever position for pushing

the machine

To Operate the Machine

Mo v e the b ypass lev ers to the inside and pull them

rearw ard, to the end the slot ( Figure 15 ).

Note: T he mac hine will not dri v e unless the

b ypass lev ers are diseng ag ed.

Adjusting the Footrest

T he footrest can be adjusted forw ard or bac kw ard

for maxim um operator comfor t.

Lift up the footrest and place the rods in the same

hole positions ( Figure 16 ).

Figure 16

1. Footrest

3. Hole positions

2. Rod

Side Discharge

T he mo w er has a hing ed g rass deﬂector that

disperses clippings to the side and do wn to w ard

the turf .

W ithout the g rass deﬂector , discharge

co v er , or complete g rass catcher assembl y

mounted in place, y ou and other s ar e

exposed to blade contact and thr o wn de bris.

Contact with r otating mo w er blade(s) and

thr o wn de bris will cause injur y or death.

• Nev er r emo v e the g rass deﬂector fr om

the mo w er because the g rass deﬂector

r outes material do wn to w ard the turf.

If the g rass deﬂector is ev er dama ged,

r eplace it immediatel y .

• Nev er put y our hands or feet under the

mo w er .

• Nev er tr y to clear discharge ar ea or

mo w er blades unless y ou mo v e the blade

contr ol s witch to Of f and r otate the

ignition k ey to Of f. Also r emo v e the k ey

and pull the wir e of f the spar k plug(s).

Operating Tips

Fast Throttle Setting

F or best mo wing and maxim um air circulation,

operate the engine at the F ast position. Air is

required to thoroughly cut g rass clippings , so

do not set the height-of-cut so lo w as to totally

sur round the mo w er b y uncut g rass . Alw a ys tr y to

ha v e one side of the mo w er free from uncut g rass ,

whic h allo ws air to be dra wn into the mo w er .

Cutting a Lawn for the First Time

Cut g rass slightly long er than nor mal to ensure

that the cutting height of the mo w er does not

scalp any unev en g round. Ho w ev er , the cutting

height used in the past is g enerally the best one to

use . W hen cutting g rass long er than six inc hes tall,

y ou ma y w ant to cut the la wn twice to ensure an

acce ptable quality of cut.

Cut 1/3 of the Grass Blade

It is best to cut only about 1/3 of the g rass blade .

Cutting more than that is not recommended unless

g rass is sparse , or it is late fall when g rass g ro ws

more slo wly .

Mowing Direction

Alter nate mo wing direction to k ee p the g rass

standing straight. T his also helps disperse clippings

whic h enhances decomposition and fer tilization.

Mow at Correct Intervals

Nor mally , mo w ev er y four da ys . But remember ,

g rass g ro ws at different rates at different times .

So to maintain the same cutting height, whic h is a

g ood practice , mo w more often in early spring . As

the g rass g ro wth rate slo ws in mid summer , mo w

less frequently . If y ou cannot mo w for an extended

period, ﬁrst mo w at a high cutting height; then

mo w ag ain tw o da ys later at a lo w er height setting .

Cutting Speed

T o impro v e cut quality , use a slo w er g round speed.

Avoid Cutting Too Low

If the cutting width of the mo w er is wider than the

mo w er y ou previously used, raise the cutting height

to ensure that unev en turf is not cut too shor t.

Long Grass

If the g rass is ev er allo w ed to g ro w slightly long er

than nor mal, or if it contains a high deg ree of

moisture , raise the cutting height higher than usual

and cut the g rass at this setting . T hen cut the g rass

ag ain using the lo w er , nor mal setting .

When Stopping

If the mac hine’ s forw ard motion m ust be stopped

while mo wing, a clump of g rass clippings ma y

drop onto y our la wn. T o a v oid this , mo v e onto a

previously cut area with the blades eng ag ed.

Keep the Underside of the Mower

Clean

Clean clippings and dir t from the underside of the

mo w er after eac h use . If g rass and dir t build up

inside the mo w er , cutting quality will ev entually

become unsatisfactor y .

Blade Maintenance

Maintain a shar p blade throughout the cutting

season because a shar p blade cuts cleanly without

tearing or shredding the g rass blades . T earing and

shredding tur ns g rass bro wn at the edg es , whic h

slo ws g ro wth and increases the c hance of disease .

Chec k the cutter blades daily for shar pness , and

for any w ear or damag e . File do wn any nic ks

and shar pen the blades as necessar y . If a blade is

damag ed or w or n, re place it immediately with a

g en uine T oro re placement blade .

Safe Towing Practices

T o w only with a mac hine that has a hitc h designed

for to wing . Do not attac h to w ed equipment ex ce pt

at the hitc h point. T his product has a limited

to wing capacity for small attac hments up to 100

lbs (45 kg); suc h as leaf sw ee pers and spreaders .

T o wing of attac hments should be limited to ﬂat

g round. Nev er allo w c hildren or others in or on

to w ed equipment. On slopes , the w eight of to w ed

equipment ma y cause a loss of traction and control.

T o wing on slopes is not r ecommended. T ra v el

slo wly and allo w extra distance to stop .

Maintenance

Note: Deter mine the left and right sides of the mac hine from the nor mal operating position.

Recommended Maintenance Schedule(s)

Maintenance Service

Interval

Maintenance Procedure

After the rst 10

operating hours

• Change the engine oil.

Before each use or daily

• Check the safety interlock system.

• Check the air lter.

• Check the engine oil level.

• Check the cutting blades.

• Clean the mower housing.

Every 25 hours

• Grease all lubrication points.

• Oil the linkage bushings (more often in dirty or dusty conditions).

• Check the battery electrolyte level.

• Check tire pressure.

• Check the belts for wear/cracks.

Every 50 hours

• Clean the air lter (more often in dirty or dusty conditions).

Every 100 hours

• Change the engine oil (more often while operating the engine under heavy

load or in high temperatures).

• Change the oil lter

• Check the spark plug.

Every 300 hours

• Clean the combustion chamber.

Yearly or before storage

• Clean the cooling system (more often in dirty or dusty conditions).

• Change the air lter (more often in dirty or dusty conditions).

• Replace spark plug.

• Clean the fuel tank and lter.

• Check the fuel line (replace if necessary).

• Replace fuel lter.

• Charge the battery and disconnect battery cables.

• Perform all maintenance procedures listed above before storage.

• Paint any chipped surfaces.

Important: R efer to y our engine operator’ s man ual f or additional maintenance pr ocedur es.

If y ou lea v e the k ey in the ignition s witch, someone could accidentl y star t the engine and

seriousl y injur e y ou or other bystander s.

R emo v e the k ey fr om the ignition and disconnect the wir e fr om the spar k plug bef or e y ou do

an y maintenance. Set the wir e aside so that it does not accidentall y contact the spar k plug .

Page is loading ...

Toro TimeCutter Z530 Riding Mower User manual

Brand: Toro

Model: TimeCutter Z530 Riding Mower

Category: Lawnmowers

Type: User manual

Download PDF

report

Toro TimeCutter Z530 Riding Mower User manual

Toro TimeCutter Z530 Riding Mower User manual

Related papers

Other documents