Linksys WAP54GPE User manual

Linksys
Brand
Linksys
Model
WAP54GPE
Category
Routers
Type
User manual
Model No.
Exterior Access Point
Wireless-G
WAP54GPE
User Guide
WIRELESS
GHz
2.4
802.11g
Wireless-G Exterior Access Point
Copyright and Trademarks
Specifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco
Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2006 Cisco Systems, Inc. All
rights reserved. Other brands and product names are trademarks or registered trademarks of their respective
holders.
How to Use this User Guide
The user guide to the Wireless-G Exterior Access Point has been designed to make understanding networking
with the Access Point easier than ever. Look for the following items when reading this User Guide:
In addition to these symbols, there are definitions for technical terms that are presented like this:
Also, each figure (diagram, screenshot, or other image) is provided with a figure number and description, like
this:
Figure numbers and descriptions can also be found in the “List of Figures” section.
This exclamation point means there is a caution or warning and is something that
could damage your property or the Access Point.
word: definition.
This checkmark means there is a note of interest and is something you should pay
special attention to while using the Access Point.
This question mark provides you with a reminder about something you might need to
do while using the Access Point.
Figure 0-1: Sample Figure Description
WAP54GPE-UG-61026 v1.1 DF
WARNING: This product contains chemicals, including lead, known
to the State of California to cause cancer, and birth defects or other
reproductive harm. Wash hands after handling.
Wireless-G Exterior Access Point
Table of Contents
Chapter 1: Introduction 1
Welcome 1
What’s in this User Guide? 2
Chapter 2: Planning Your Wireless Network 4
Network Topology 4
Roaming 4
Network Layout 4
Example of a Simple Wireless Network 5
Chapter 3: Getting to Know the Wireless-G Exterior Access Point 6
The LEDs 6
The Ports 7
The Reset Button and Ground 8
The Antenna Pattern 9
Chapter 4: Connecting the Wireless-G Exterior Access Point 12
Overview 12
Hardware Installation 12
Chapter 5: Setting Up the Wireless-G Exterior Access Point 14
Overview 14
Accessing the Utility 14
Navigating the Utility 15
Chapter 6: Configuring the Wireless-G Exterior Access Point 17
The Setup Tab 17
The Setup - Time Tab 18
The Wireless - Basic Wireless Settings Tab 19
The Wireless - Wireless Security Tab 21
The Wireless - Wireless Connection Control Tab 26
The Wireless - Advanced Wireless Settings Tab 27
The AP Mode Tab 29
The Administration - Management Tab 32
The Administration - Log Tab 34
The Administration - Factory Default Tab 36
The Administration - Firmware Upgrade Tab 36
Wireless-G Exterior Access Point
The Administration - Reboot Tab 37
The Administration - Config Management Tab 38
The Status - Local Network Tab 39
The Status - Wireless Tab 40
The Status - System Performance Tab 41
Appendix A: Troubleshooting 43
Frequently Asked Questions 43
Appendix B: Wireless Security 47
Security Precautions 47
Security Threats Facing Wireless Networks 47
Appendix C: Upgrading Firmware 50
Appendix D: Windows Help 51
Appendix E: Glossary 52
Appendix F: Specifications 57
Appendix G: Warranty Information 59
Appendix H: Regulatory Information 60
Appendix I: Contact Information 66
Wireless-G Exterior Access Point
List of Figures
Figure 2-1: Example of a Simple Wireless Network 5
Figure 3-1: Front Panel 6
Figure 3-2: Bottom Panel 7
Figure 3-3: Top Panel 7
Figure 3-4: Back Panel 8
Figure 3-5: Internal Antenna Pattern (Horizontal Plane) 9
Figure 3-6: Radio Coverage of the Access Point to Client Devices 10
Figure 3-7: Access Point to Access Point (bridging) Radio Coverage 11
Figure 4-1: Mark the Locations of the Two Wall-Mount Slots 12
Figure 4-2: Attach the Mounting Plate 12
Figure 4-3: Ground the Access Point 13
Figure 4-4: Attach the Access Point to the Wall 13
Figure 5-1: Login Screen 14
Figure 6-1: Setup - Static IP Address 17
Figure 6-2: Setup - Automatic Configuration - DHCP 18
Figure 6-3: Setup - Time 18
Figure 6-4: Wireless - Basic Wireless Settings 19
Figure 6-5: Wireless - Wireless Security (Disabled) 21
Figure 6-6: Wireless - Wireless Security (WPA-Personal) 21
Figure 6-7: Wireless - Wireless Security (WPA2-Personal) 22
Figure 6-8: Wireless - Wireless Security (WPA2-Personal Mixed) 22
Figure 6-9: Wireless - Wireless Security (WPA-Enterprise) 23
Figure 6-10: Wireless - Wireless Security (WPA2-Enterprise) 23
Figure 6-11: Wireless - Wireless Security (WPA2 - Enterprise Mixed) 24
Figure 6-12: Wireless Security - RADIUS 25
Figure 6-13: Wireless Settings - WEP 25
Figure 6-14: Wireless - Wireless Connection Control 26
Figure 6-1: Select MAC Address from Client Association Table 26
Wireless-G Exterior Access Point
Figure 6-15: Wireless - Advanced Wireless 27
Figure 6-16: AP Mode 29
Figure 6-17: Wireless Repeater 30
Figure 6-18: Site Survey 31
Figure 6-19: Administration - Management 32
Figure 6-20: The Administration - Log 34
Figure 6-21: Administration - Factory Default 36
Figure 6-22: Administration - Firmware Upgrade 36
Figure 6-23: Administration - Reboot 37
Figure 6-24: Administration - Config Management 38
Figure 6-25: Status - Local Network 39
Figure 6-26: Status - Wireless 40
Figure 6-27: Status - System Performance 41
Figure C-1: Firmware Upgrade 50
1
Chapter 1: Introduction
Welcome
Wireless-G Exterior Access Point
Chapter 1: Introduction
Welcome
Thank you for choosing the Wireless-G Exterior Access Point. This Access Point will allow you to network
wirelessly better than ever.
How does the Access Point do all of this? An access point allows for greater range and mobility within your
wireless network while also allowing you to connect the wireless network to a wired environment. In fact, the
Wireless-G Exterior Access Point can support communications on up to eight wireless networks, using Virtual
Local Area Network (VLAN) technology.
The Wireless-G Exterior Access Point also offers the convenience of Power over Ethernet (PoE) capability, so it
can receive data and power over a single Ethernet network cable. And with the advantage of its weather-proof
housing, you can mount the Access Point outside to extend your wireless networking range and mobility to the
outdoors. You can even connect wired networks in two different buildings, by using two Access Points set to
Wireless Bridge mode.
But what does all of this mean?
Networks are useful tools for sharing computer resources. You can access one printer from different computers
and access data located on another computer's hard drive. Networks are even used for playing multiplayer video
games. So, networks are not only useful in homes and offices, they can also be fun.
PCs on a wired network create a LAN, or Local Area Network. They are connected with Ethernet cables, which is
why the network is called "wired".
PCs equipped with wireless client cards or adapters can communicate without cumbersome cables. By sharing
the same wireless settings, within their transmission radius, they form a wireless network. This is sometimes
called a WLAN, or Wireless Local Area Network. The Access Point bridges wireless networks of both 802.11g and
802.11b standards and wired networks.
Use the instructions in this Guide to help you connect the Access Point, set it up, and configure it to bridge your
different networks. These instructions should be all you need to get the most out of the Access Point.
802.11b: a wireless networking standard that specifies a
maximum data transfer rate of 11Mbps and an operating
frequency of 2.4GHz.
802.11g: a wireless networking standard that specifies a
maximum data transfer rate of 54Mbps, an operating
frequency of 2.4GHz, and backward compatibility with
802.11b devices.
adapter: a device that adds network functionality to your
PC.
ethernet: network protocol defined in IEEE 802.3 standard
that specifies how data is placed on and retrieved from a
common transmission medium.
lan (local area network): the computers and networking
devices that make up your local network.
network: a series of computers or devices connected
together.
poe (power over ethernet): a technology enabling an
Ethernet network cable to deliver both data and power.
access point: a device that allows wireless-equipped
computers and other devices to communicate with each
other and with devices on a wired network. Also used to
expand the range of a wireless network.
2
Chapter 1: Introduction
What’s in this User Guide?
Wireless-G Exterior Access Point
What’s in this User Guide?
This user guide covers the steps for setting up and using the Wireless-G Exterior Access Point.
• Chapter 1: Introduction
This chapter describes the Wireless-G Exterior Access Point’s applications and this User Guide.
• Chapter 2: Planning your Wireless Network
This chapter describes the basics of wireless networking.
• Chapter 3: Getting to Know the Wireless-G Exterior Access Point
This chapter describes the physical features of the Access Point.
• Chapter 4: Connecting the Wireless-G Exterior Access Point
This chapter instructs you on how to connect the Access Point to your network.
• Chapter 5: Setting up the Wireless-G Exterior Access Point
This chapter explains how to perform basic setting changes through the Web-based Utility.
• Chapter 6: Configuring the Wireless-G Exterior Access Point
This chapter provides a reference for the available configuration through the Web-based Utility.
• Appendix A: Troubleshooting
This appendix describes some frequently asked questions regarding installation and use of the Wireless-G
Exterior Access Point.
• Appendix B: Wireless Security
This appendix explains the risks of wireless networking and some solutions to reduce the risks.
• Appendix C: Upgrading Firmware
This appendix instructs you on how to upgrade the Access Point’s firmware.
• Appendix D: Windows Help.
This appendix describes some of the ways Windows can help you with wireless networking.
• Appendix E: Glossary
This appendix gives a brief glossary of terms frequently used in networking.
• Appendix F: Specifications
This appendix provides the Access Point’s technical specifications.
3
Chapter 1: Introduction
What’s in this User Guide?
Wireless-G Exterior Access Point
• Appendix G: Warranty Information
This appendix supplies the Access Point’s warranty information.
• Appendix H: Regulatory Information
This appendix supplies the Access Point’s regulatory information.
• Appendix I: Contact Information
This appendix provides contact information for a variety of Linksys resources, including Technical Support.
4
Chapter 2: Planning Your Wireless Network
Network Topology
Wireless-G Exterior Access Point
Chapter 2: Planning Your Wireless Network
Network Topology
A wireless network is a group of computers, each equipped with one or more wireless adapters. Computers in a
wireless network must be configured to share the same radio channel to talk to each other. Several PCs equipped
with wireless cards or adapters can communicate with each other to form an ad-hoc network without the use of
an access point.
Linksys wireless adapters also provide access to a wired network when using an access point, such as the
Wireless-G Exterior Access Point, or wireless router. An integrated wireless and wired network is called an
infrastructure network. Each wireless PC in an infrastructure network can talk to any computer in a wired or
wireless network via the access point or wireless router.
An infrastructure configuration extends the accessibility of a wireless PC to a wired network, and may double the
effective wireless transmission range for two wireless adapter PCs. Since an access point is able to forward data
within a network, the effective transmission range in an infrastructure network may be doubled (depending on
antenna characteristics).
Roaming
Infrastructure mode also supports roaming capabilities for mobile users. Roaming means that you can move your
wireless PC within your network and the access points will pick up the wireless PC's signal, providing that they
both share the same wireless channel and SSID.
Before you consider roaming, choose a feasible radio channel and optimum access point position. Proper access
point positioning combined with a clear radio signal will greatly enhance performance.
Note that Spanning Tree Protocol should be disabled on the switches connecting to the APs to allow roaming to
work without disruption.
Network Layout
The Wireless-G Exterior Access Point has been designed for use with 802.11g and 802.11b products. The Access
Point is compatible with 802.11g and 802.11b adapters, such as the Notebook Adapters for your laptop
computers, PCI Adapters for your desktop PCs, and USB Adapters for when you want to enjoy USB connectivity.
These wireless products can also communicate with a 802.11g or 802.11b Wireless PrintServer.
infrastructure: a wireless network that is bridged to a wired
network via an access point.
ad-hoc: a group of wireless devices communicating directly
with each other (peer-to-peer) without the use of an access
point.
roaming: the ability to take a wireless device from one
access point's range to another without losing the
connection.
ssid: your wireless network's name
5
Chapter 2: Planning Your Wireless Network
Example of a Simple Wireless Network
Wireless-G Exterior Access Point
To link your wired network with your wireless network, connect the Access Point’s Ethernet network port to any
switch or router with Power over Ethernet (PoE)—or a PoE injector, such as the Linksys WAPPOE or WAPPOE12.
Note that 12 VDC on WAPPOE12 is for the splitter output. Both PoE Injectors provide 48 VDC power output.
With these and many other Linksys products, your networking options are limitless. Go to the Linksys website at
www.linksys.com for more information about wireless products.
Example of a Simple Wireless Network
Figure 2-1: Example of a Simple Wireless Network
The above diagram shows a typical infrastructure wireless network setup. The Wireless Access Points are
connecting to a Linksys switch that provides power to the Access Points. Each Access Point can connect multiple
wireless devices to the network. This network will provide connectivity among wireless network devices and PCs
that have a wired connection to the switch.
The switch then can connect to a router that can connect to an ISP to reach global Internet.
6
Chapter 3: Getting to Know the Wireless-G Exterior Access Point
The LEDs
Wireless-G Exterior Access Point
Chapter 3: Getting to Know the Wireless-G Exterior
Access Point
The LEDs
The Access Point's LEDs, where information about network activity is displayed, are located on the front panel.
Power Green. The power LED lights up when the Access Point is powered on.
Wired Green. The Wired LED lights up when the Access Point is successfully connected to a device
through the Ethernet network port. If the Wired LED is flashing, the Access Point is actively
sending to or receiving data from one of the devices over the Ethernet network port.
Wireless Green. The Wireless LED lights up when the Access Point is successfully connected to a
wireless device. If the Wireless LED is flashing, the Access Point is actively sending to or
receiving data from a wireless device.
Figure 3-1: Front Panel
7
Chapter 3: Getting to Know the Wireless-G Exterior Access Point
The Ports
Wireless-G Exterior Access Point
The Ports
The Access Point's Ethernet network port is located on the bottom panel and the antenna port is located on the
top panel.
Ethernet The Ethernet network port connects to Ethernet network devices, such as a switch or router
that supports Power over Ethernet (PoE).
Antenna The Access Point has a built-in, 9dBi directional antenna. It also has a reverse polarity female
N-type antenna port for an optional, high-gain external antenna such as the HGA9N. The
internal antenna will be disabled automatically when an external antenna is connected.
Figure 3-2: Bottom Panel
Figure 3-3: Top Panel
port: the connection point on a computer or
networking device used for plugging in
cables or adapters
8
Chapter 3: Getting to Know the Wireless-G Exterior Access Point
The Reset Button and Ground
Wireless-G Exterior Access Point
The Reset Button and Ground
The Access Point's Reset button and ground are located on the back panel.
Reset Button There are two ways to Reset the Access Point's factory defaults. Either press the Reset
button, for approximately ten seconds, or restore the defaults using the Access Point's Web-
based Utility.
Ground Before you mount the Access Point, you must ground the Access Point (to a large piece of
metal) as a precaution against electric shock.
Figure 3-4: Back Panel
Reset Button
Ground
IMPORTANT: Resetting the Access Point will
erase all of your settings (including wireless
security, IP address, and power output) and
replace them with the factory defaults. Do not
reset the Access Point if you want to retain
these settings.
9
Chapter 3: Getting to Know the Wireless-G Exterior Access Point
The Antenna Pattern
Wireless-G Exterior Access Point
The Antenna Pattern
The above diagram shows the antenna pattern of the built-in directional antenna on the horizontal plane. The
power of the wireless signal is most strong on the direction perpendicular to the front surface (with Linksys logo)
of the Access Point. The peak gain of this antenna is 9dBi. The 3dB beamwidth is 47 degrees.
Figure 3-5: Internal Antenna Pattern (Horizontal Plane)
10
Chapter 3: Getting to Know the Wireless-G Exterior Access Point
The Antenna Pattern
Wireless-G Exterior Access Point
When using the Access Point to connect client devices, adjust it so the client devices are on the same horizontal
plane as the Access Point and within a 3dB angle of 47 degrees. This will ensure the strongest signal and
maximum reach.
If the Access Point is used inside a building, put it in a corner of the building for maximum coverage.
Figure 3-6: Radio Coverage of the Access Point to Client Devices
11
Chapter 3: Getting to Know the Wireless-G Exterior Access Point
The Antenna Pattern
Wireless-G Exterior Access Point
If the Access Point is used as a bridge or repeater, adjust the Access Points to face each other to ensure the
strongest signal and maximum reach.
Make sure that the orientation of the two Directional Antennas is the same. The radio wave is polarized so a 90
degree rotation will result in no received power.
Due to its directional characteristics, the internal antenna is ideal for point-to-point bridge mode or the spoke
side of point-to-multipoint bridge mode. It is recommended to use an external omni-directional antenna (e.g.
HGA9N) for repeater mode applications.
Figure 3-7: Access Point to Access Point (bridging) Radio Coverage
12
Chapter 4: Connecting the Wireless-G Exterior Access Point
Overview
Wireless-G Exterior Access Point
Chapter 4: Connecting the Wireless-G Exterior Access
Point
Overview
This chapter explains how to mount and connect the Access Point.
Depending on your application, you might want to set up the IP address of the device first before mounting the
device. Refer to "Chapter 5: Setting Up the Wireless-G Exterior Access Point".
Hardware Installation
1. Locate an optimum location on a wall for the Access Point. Refer to the antenna pattern in "Chapter 3: Getting
to Know the Wireless-G Exterior Access Point" to adjust the angle of the Access Point for your application.
2. Using the mounting plate as a template, mark the locations of the two wall-mount slots that are on the bottom
of the mounting plate. Then, install a screw into each location.
3. Use four screws (included with the Access Point) to attach the mounting plate to the back panel of the Access
Point.
4. Connect the included Category 5e Ethernet network cable to the Ethernet network port of the Access Point.
Then, screw the connector cap tightly onto the port, so the Access Point has a water-resistant seal.
5. If you want to connect an optional, high-gain external antenna, unscrew the cap that protects the Type-N
antenna port, then, connect your antenna cable to this port.
hardware: the physical aspect of
computers, telecommunications, and
other information technology devices.
Figure 4-1: Mark the Locations of the Two Wall-Mount Slots
Figure 4-2: Attach the Mounting Plate
13
Chapter 4: Connecting the Wireless-G Exterior Access Point
Hardware Installation
Wireless-G Exterior Access Point
6. Make sure that you properly ground the Access Point.
7. Line up the Access Point’s wall-mount slots with the two screws on the wall. Then, slide the Access Point
down so that the screws fit snugly in the slots.
8. Attach a screw (not included) in each of the two holes on the top of the mounting plate so that the Access
Point is securely mounted to the wall.
9. Connect the other end of the Ethernet network cable to a switch, router, or other device that supports Power
over Ethernet. The Access Point will then be connected to your wired network.
Now that the hardware installation is complete, proceed to "Chapter 5: Setting Up the Wireless-G Exterior Access
Point," for directions on how to configure the Access Point.
Figure 4-4: Attach the Access Point to the Wall
Figure 4-3: Ground the Access Point
14
Chapter 5: Setting Up the Wireless-G Exterior Access Point
Overview
Wireless-G Exterior Access Point
Chapter 5: Setting Up the Wireless-G Exterior Access
Point
Overview
The Access Point has been designed to be functional right out of the box with the default settings. However, if
you'd like to change these settings, the Access Point can be configured through your web browser with the Web-
based Utility. This chapter explains how to use the Utility.
The Utility can be accessed via web browsers, such as Microsoft Internet Explorer or Mozilla Firefox through the
use of a computer that is networked with the Access Point.
For a basic network setup, most users only have to use the following screens of the Utility:
• Setup
On the Setup screen, enter your basic network settings (IP address) here.
• Management
Click the Administration tab and then select the Management screen. The Access Point’s default password
is admin. To secure the Access Point, change the AP Password from its default.
Most users will also customize their wireless settings:
• Wireless
On the Wireless screen, change default SSID under the Basic Wireless Settings Tab. Select the level of
security under the Wireless Security Tab.
Accessing the Utility
There are three ways to connect to your Access Point for the first time.
1. If you have a 48V Power Injector (e.g. Linksys WAPPOE), power up your Access Point first then connect the
cable on your Injector to your PC. Configure your PC to have static IP address on the same subnet as the
Access Point’s default IP address (192.168.1.245).
2. If you have a PoE switch (e.g. Linksys SRW224P), connect your Access Point and your PC to the same LAN.
Configure your PC to have the static IP address on the same subnet as the Access Point’s default IP address
HAVE YOU: Enabled TCP/IP on your PCs? PCs
communicate over the network with this
protocol. Refer to “Appendix D: Windows Help”
for more information on TCP/IP.
browser: an application that provides a way to
look at and interact with all the information on the
World Wide Web.
tcp/ip: a set of protocols PCs use to
communicate over a network.
Figure 5-1: Login Screen
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72

Linksys WAP54GPE User manual

Linksys
Brand
Linksys
Model
WAP54GPE
Category
Routers
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents