Adlink NuPRO-850 User manual

Brand: Adlink

Model: NuPRO-850

Category: Motherboards

Type: User manual

This manual is also suitable for

NuPRO-850 Series

Recycled Paper

NuPRO-850

Full-Size ePCI-X System

Host Board

Intel® Pentium® 4 processor

User’s Manual

Manual Rev. 1.00: June 18, 2004

Part Number: 50-13045-100

The information in this document is subject to change without prior notice in

order to improve reliability, design, and function and does not represent a

commitment on the part of the manufacturer.

In no event will the manufacturer be liable for direct, indirect, special,

incidental, or consequential damages arising out of the use or inability to use

the product or documentation, even if advised of the possibility of such

damages.

This document contains proprietary information protected by copyright. All

rights are reserved. No part of this manual may be reproduced by any

mechanical, electronic, or other means in any form without prior written

permission of the manufacturer.

Trademarks

NuDAQ

, NuIPC

, NuDAM

, NuPRO

are registered trademarks of ADLINK

Technology Inc. Other product names mentioned herein are used for

identification purposes only and may be trademarks and/or registered

trademarks of their respective companies.

Getting Service from ADLINK

Customer Satisfaction is top priority for ADLINK Technology Inc. If you need

any help or service, please contact us.

ADLINK TECHNOLOGY INC.

Web Site http://www.adlinktech.com

Sales & Service [email protected]

TEL +886-2-82265877 FAX +886-2-82265717

Address 9F, No. 166, Jian Yi Road, Chungho City, Taipei, 235 Taiwan

Please email or FAX your detailed information for prompt, satisfactory, and

consistent service.

Detailed Company Information

Company/Organization

Contact Person

E-mail Address

Address

Country

TEL FAX

Web Site

Questions

Product Model

Environment

OS:

Computer Brand:

M/B: CPU:

Chipset: BIOS:

Video Card:

NIC:

Other:

Detail Description

Suggestions for ADLINK

List of Tables and Figures • i

Table of Contents

Chapter 1 Introduction..................................................................1

1.1

Unpacking Checklist........................................................................ 2

1.2

Features .......................................................................................... 3

1.3

Functional Blocks and Main Board.................................................. 4

1.4

Specifications.................................................................................. 8

Chapter 2 Jumpers and Connectors.........................................11

2.1

NuPRO-850 Board Outline and Illustration................................... 12

2.2

NuPRO-850 Connector Pin Assignments...................................... 14

Chapter 3 Getting Started...........................................................25

3.1

CPU Installation ...........................................................................25

3.2

Memory Installation....................................................................... 26

3.3

Connecting IDE Devices to the NuPRO-850................................. 27

3.4

BIOS Configuration Overview .......................................................28

3.5

Operating System Installation ....................................................... 29

Chapter 4 Device Driver Installation..........................................31

4.1

Intel® 875P/6300ESB Chipset...................................................... 31

4.2

Driver Installation .......................................................................... 32

Chapter 5 Watchdog Timer.........................................................35

5.1

Watchdog Timer............................................................................35

Chapter 6 ePCI-X Bus Details.....................................................41

6.1

NuPRO-850 ePCI-X Bus............................................................... 41

6.2

Global Signals............................................................................... 41

6.3

PCI-X Bus Signals......................................................................... 42

Warranty Policy ...........................................................................43

ii • How to Use This Guide

How to Use This Guide

This manual is designed to help users configure the NuPRO-850 Full-Size

ePCI-X System Host Board with Dual Xeon CPU. It is divided into five

chapters.

Chapter 1

Introduction

Gives an overview of the product features, applications, and

specifications.

Chapter 2

Connectors and Jumpers

Outlines all the connectors and its pin definitions.

Chapter 3

Getting Started

Summarization of what is required to setup an operational

system using the NuPRO-850. Hardware installation and BIOS

overview is discussed.

Chapter 4

Driver Installation

Detailed instructions on how to install the software drivers

successfully.

Chapter 5

Utilities

Explains the operation of the WDT, PXE booting, and Hardware

Doctor.

Introduction • 1

Introduction

The NuPRO-850 is a full-size ePCI-X System Host Board (SHB) based on the

Intel® Pentium® 4 processor and 875P Memory Controller Hub / 6300ESB I/O

Controller Hub chipset. It features AGP4X/8X VGA, Serial ATA I/F, Gigabit

Ethernet, and USB v2.0 I/F. It supports two PCI/PCI-X busses via the Intel

6300ESB chipset (one PCI-X 64-bit/66MHz bus and one PCI 32-bit/33MHz

bus). The NuPRO-850 is designed to run under Windows 2000/XP and Linux

operating systems as well as in embedded real time applications.

The NuPRO-850 is a System Host Board with premium computing

performance powered by an Intel® Pentium® 4 processor. The CPU module

supports a front side bus (FSB) of 533/800MHz and a maximum CPU clock

speed of 3.4GHz featuring 64-bit/66MHz PCI/PCI-X bus with up to 4GB high

performance DDR host SDRAM support.

It provides input/output via RS-232, four USB 2.0 ports, Dual IDE Channels

with ATA 100/66/33, Onboard Gigabit Ethernet, and video interfaces for LVDS

Digital LCD Display and dual CRT displays. The NuPRO-850 is designed to

meet the needs of applications which require the highest computing

performance and highest reliability and is designed to run Windows 2000/XP

and Linux operating systems, as well as embedded real-time applications. It is

the ideal solution for telecommunications, internet, and industrial networking

applications.

This chapter is designed to give the user with an overview of the NuPRO-850

SHB. This chapter covers the following topics:

• Unpacking and Checklist

• Features

• Specifications

2 • Introduction

1.1 Unpacking Checklist

Check the shipping carton for any damage. If the shipping carton and contents

are damaged, notify the dealer for a replacement. Retain the shipping carton

and packing materials for inspection by the dealer. Obtain authorization before

returning any product to ADLINK.

Check the following items are included in the package, if there are any items

missing, contact your dealer.

• The NuPRO-850 module (May be equipped with different speed or

capacity CPU, RAM, and HDD).

• This User’s Manual

• ADLINK CD

• Com Cable

• Dual Ports USB Cable with bracket

• 1 set of Cooler kits

• 2 x ATA-100 Cables

• 2 x Serial ATA Cables

Note: The package of the NuPRO-850 OEM version non-standard

configuration may vary in function or contents according to

different configuration requests

CAUTION: This board must be protected from static discharge and

physical shock. Never remove any of the socketed parts except

at a static-free workstation. Use the anti-static bag shipped with

the product to handle the board. Wear a wrist strap grounded

through one of the system's ESD Ground jacks while servicing

system components.

Introduction • 3

1.2 Features

• PICMG 1.2 Rev 1.0 Embedded PCI-X Specification compliant.

• PCI Local Bus Specification, Rev 2.2 compliant.

• Single Intel® Pentium® 4 processor with 1MB L2 cache,

533/800MHz FSB, Hyper-Threading Technology.

• Four 184-pin DIMM sockets, support single/dual channel DDR

DIMM. Up to four DIMMs of DDR 266/333/400 with ECC unbuffered.

Supports a maximum of 4GB of system memory.

• Intel® 82547GI Gigabit Ethernet Controller. Supports 1000Base-TX,

100Base-TX and 10Base-T (IEEE802.3, 802.3u, and 802.3ab).

• ATI Mobility M9/M10 with AGP4X/8X compliant, 64MB memory.

LVDS signal output connector supports LVDS Digital LCD Display

and dual CRT displays.

• AC'97 link Interface, AC’97 2.2 compliant with optional with ADLINK

DB-AC97 board.

• Supports all generic features include VGA, COM port, USB 2.0,

keyboard, mouse, and hardware monitoring.

• Built-in monitoring CPU temperatures, FAN speed, system

temperature, CPU voltage, and DC voltages.

• Supports Intel

Pre-boot Execution Environment (PXE).

• 2 x IDE channels, 2 x SATA ports.

4 • Introduction

1.3 Functional Blocks and Main Board

The following topics provide an overview of the NuPRO-850 main features as

shown in the functional block diagram below and also the main board.

Functional Block Diagram

Figure 1: Functional Block Diagram

Introduction • 5

Main Board Drawing

Figure 2: Main Board Drawing

6 • Introduction

1.3.1 Intel® Pentium® 4 Processor

The Intel® Pentium® 4 processor is based on Intel® NetBurst®

microarchitecture and built with Intel®'s 0.13-micron and 90nm manufacturing

process and featuring Hyper-Threading technology, a 1MB level two-cache

size. The Intel® Pentium® 4 has a maximum clock speed of 3.4GHz and front

side bus frequency of 400/533/800MHz.

The Intel® NetBurst™ micro-architecture and Hyper-Threading Technology is

designed specifically for multi-tasking environments and provides outstanding

performance for multi-threaded applications.

1.3.2 Video

The NuPRO-850 provides standard SVGA CRT analog output on a bracket I/O

panel. The video function is provided via an ATI Mobility M9 (AGP4X) or M10

(AGP8X) VGA chip with 64MB video memory. NuPRO-850 also supports dual

CRT output (via one onboard 14-pin header) and one LVDS interface. The

NuPRO-850 has one jumper to disable the onboard video and BIOS options

are used to select the resolution of the LVDS panel

1.3.3 Ethernet Interfaces

The NuPRO-850 provides one 10/100/1000Mbps Ethernet interface via the

Intel® 82547GI Gigabit Ethernet Controller. The 82547GI is connected to the

CSA (Communicating Streaming Architecture) interface of the 875P MCH. The

Ethernet interface is routed to a RJ-45 w/LED all-in-one connector on bracket.

The LAN chip will be assigned one unique static MAC Address. LED drive

signals for Ethernet link status and activity are routed to the same connector.

1.3.4 Serial I/O

The NuPRO-850 has one RS-232 serial port with a 10-pin connector. The

16550 compatible serial port is provided by the SIU port on the Intel® 6300ESB

ICH.

1.3.5 Universal Serial Bus (USB)

The NuRPRO-850 supports four USB 2.0 ports, with two connectors (USB0 &

USB1) on bracket and the remaining (USB2 & USB3) routed to one onboard

9-pin header. USB allows for the easy addition of peripherals such as mouse,

keyboard, speakers, etc.

1.3.6 IDE and Serial ATA Controller Controller

The NuPRO-850 provides IDE and Serial ATA interfaces from the Intel®

6300ESB ICH. Two IDE connectors can support up to four drives Ultra DMA

100 Mode. Two serial ATA ports support up to two serial ATA devices for data

transfer rates up to 150Mbps.

Introduction • 7

1.3.7 Software

The NuPRO-850 is compatible with all major PC operating systems. ADLINK

provides support, which may include additional drivers for ADLINK peripherals.

Software device drivers for the NuPRO-850 may be found in the ADLINK CD.

1.3.8 AC’97 Link

NuPRO-850 provides one AC’97 link 10-pin header, the AC’97 link is provided

by the 6300ESB ICH.

1.3.9 Serial I/O

NuPRO-850 provides one RS-232 serial port via one 10-pin connector. The

serial port is provided by the 16550 compatible SIU port in the 6300ESB ICH.

1.3.10 MiniPCI slot

NuPRO-850 provides one MiniPCI type III slot. The MiniPCI slot and ePCI-X

bus B share the 6300ESB PCI bus I/F.

8 • Introduction

1.4 Specifications

Compliant Specifications

• PICMG 1.2 Rev 1.0 Embedded PCI-X Specification compliant.

• PCI Local Bus Specification, Rev 2.2 compliant.

Form Factor

• Standard Full-Size ePCI-X System Host Board, 338.6mm x 122mm

(13.33”x4.8”).

CPU/Cache

• Intel® Pentium® 4 processor. The socket supports CPUs manufactured

using Intel's 0.13-micron and 90nm manufacturing processes, FC-mPGA4

package (478-pin).

• The Intel

Pentium® 4 processor runs at a core speed of up to 3.4GHz,

with a Front Side Bus (FSB) speed of 400/533/800MHz, and on-die 512KB

or 1MB Advanced Transfer L2 Cache.

Chipset

• Intel

6300ESB I/O Controller Hub

• Intel® 82875P Memory Controller Hub (MCH)

Host Memory

• Four DDR DIMM sockets

• 266/333/400MHz DDR DIMM modules

• Dual-channel or single-channel DDR interface

• Non-ECC and ECC, un-buffered DIMMs only

• Each socket supports up to 1GB of DDR DIMM

• 128-Mb, 256-Mb, 512Mb technologies implemented as x8, x16 DDR

devices with four banks

• Up to 4GB system memory

• Registered DIMMs are not supported

DDR DIMM speed, type and size can be determined by the BIOS reading the

DIMM presence detect bits on the SMBus (System Management Bus). The

Introduction • 9

DDR DIMM timing register, which provides the DIMM speed control for the

entire array, must be programmed to use the timings of the slowest DIMMs

installed. Note: DIMMs must be populated in identical pairs for dual-channel

operation

BIOS

: Award / Phoenix BIOS advanced by ADLINK

• NuPRO-850 supports BIOS memory size up to 8Mbytes (Firmware Hub

I/F).

• Flash write protection will be implemented under software control. This bit

must be set to 1 before any write will be allowed to the BIOS Flash.

Gigabit Ethernet

• One 10/100/1000Mbps Ethernet interfaces via the Intel® 82547GI Gigabit

Ethernet Controller. The 82547GI is connected to the CSA

(Communicating Streaming Architecture) interface of the 82875P MCH.

• Support 1000Base-T, 100Base-TX and 10Base-T (IEEE 802.3, 802.3u,

and 802.3ab).

• IEEE802.3x compliant flow control, support auto-negotiation and link

setup.

• Ethernet link status and activity LEDs on the RJ-45 connector.

Graphic Display

• ATI Mobility M9 (AGP4X) or M10 (AGP8X) VGA chip with 64MB video

memory.

• Standard SVGA CRT analog output on bracket I/O panel.

• Also supports 2

CRT output (via one onboard 14-pin header) and one

LVDS interface.

USB Interface

• Supports four USB 2.0 ports, two connectors (USB0 & USB1) on bracket

and the others (USB2 & USB3) are routed to one onboard 9-pin header

IDE Ports

• Two IDE connectors support up to four drivers. Up to Ultra DMA 100

Mode.

Super I/O and WDT

• Built-in HanceRapids, support 2-stage WDT, programmable timer 1 - 255

seconds or 1 - 255 minutes.

10 • Introduction

• The NuPRO-850 edge connector uses three standard 32-bit PCI

connectors. These three connectors carry two busses, one PCI-X

64-bit/66MHz bus and one PCI 32-bit/33MHz bus. Both busses are

provided by Intel 6300ESB ICH.

Hardware Monitor

• The W83L784R provides temperature, fans, and voltage monitors. It has

analog to digital converters that allow software to monitor the voltages on

NuPRO-850.

OS Compatibility

• MS-DOS 6.2+, Windows 2000/XP, Red Hat Linux 7.3 or higher

• Other OS support available upon request

Environment

• Operating temperature: 5 to 55 °C

• Storage temperature: -40 to 70 °C

• Humidity: 5% to 95% non-condensed

Safety Certificate and Test

• CE, FCC

• All plastic material used onboard are all UL-94V certified

Jumpers and Connectors • 11

Jumpers and Connectors

This chapter will familiarize the user with the NuPRO-850 with the interfaces and

connections available before getting started. The chapter also contains

information about the board layout, connector definitions and jumper setup as

well as the following information:

• NuPRO-850 board outline and illustration

• NuPRO-850 connectors pin assignments

• NuPRO-850 jumpers setting

12 • Jumpers and Connectors

2.1 NuPRO-850 Board Outline and Illustration

2.1.1 NuPRO-850 Top View

CN16

LAN1

CN13

CN3

CN6

CN4

CN7

CN9

JP1

CN10

JPY1

CN11

CN12

CN14

CN17

CN1

CN2

FN1

PN1

U12

FN2

DIMM1

DIMM2

DIMM3

DIMM4

ePCI-X bus A

ePCI-X bus B

CN18

ure 3: NuPRO-850 To

Vie

Jumpers and Connectors • 13

2.1.2 Front View

Figure 4: View of Face Plate

Position Description

CN1 Case open pin header

CN2 Front panel pin header

CN3 COM1 connector

CN4 Secondary IDE connector

CN6 AC’97 link connector

CN7 Primary IDE connector

CN9 MiniPCI slot

CN10 SATA-1 connector

CN11 SATA-0 connector

CN12 VGA 2

CRT pin header

CN13 VGA CRT connector

CN14 LVDS connector

CN16 USB-0 connector

CN17 USB-1 connector

CN18 USB-2/3 pin header

LAN1 Gigabit Ethernet RJ-45 connector

FN1 VGA Fan power connector

FN2 CPU Fan power connector

DIMM1 DDR DIMM B1 socket

DIMM2 DDR DIMM B2 socket

DIMM3 DDR DIMM A1 socket

DIMM4 DDR DIMM A2 socket

U12 CPU socket

PN1 ATX 12V 4-pin connector

JP1 Clear CMOS jumper

JPY1 VGA disable jumper

CN17 CN16

LAN1

CN13

14 • Jumpers and Connectors

Table 1: Description of Connector Locations

2.2 NuPRO-850 Connector Pin Assignments

A detailed description and pin-out for each connector is given in the following

section.

2.2.1 VGA CRT connector (CN13)

Table 2: VGA Connector Pin Definition

2.2.2 USB 2.0 connector (CN16, CN17)

Pin # Signal Name

1 VCC

2 USB-

3 USB+

4 Ground

Table 3: USB Connectors Pin Definition

PIN SIGNAL FUNCTION

RED Analog RED

GREEN Analog GREEN

BLUE Analog BLUE

NC No Connect

GND Ground

5VCC +5V

GND Ground

NC No connect

DDC_DATA DDC Data for

CRT

HSYNC Horizontal sync

for Monitor

VSYNC Vertical sync for

Monitor

DDC_CLK DDC Clock for

CRT

Page is loading ...

Adlink NuPRO-850 User manual

Brand: Adlink

Model: NuPRO-850

Category: Motherboards

Type: User manual

This manual is also suitable for

NuPRO-850 Series

Download PDF

report

Adlink NuPRO-850 User manual

This manual is also suitable for

Adlink NuPRO-850 User manual

Related papers

Other documents