GROHE 19 822 User manual

Category
Faucets
Type
User manual

This manual is also suitable for

GROHE 19 822 is a thermostat mixer with a variety of features and possible use cases. It has two integrated service stops, a flow pressure of 1-5 bar, and a maximum operating pressure of 8.5 bar. The flow rates at 3 bar are 24 l/min for the bottom outlet and 12 l/min for the top outlet. The temperature range is limited to 43 °C or 110 °F, with a first safety stop at 38 °C or 100 °F. The GROHE 19 822 is suitable for use with the GrohFlexTM universal rough-in valve.

GROHE 19 822 is a thermostat mixer with a variety of features and possible use cases. It has two integrated service stops, a flow pressure of 1-5 bar, and a maximum operating pressure of 8.5 bar. The flow rates at 3 bar are 24 l/min for the bottom outlet and 12 l/min for the top outlet. The temperature range is limited to 43 °C or 110 °F, with a first safety stop at 38 °C or 100 °F. The GROHE 19 822 is suitable for use with the GrohFlexTM universal rough-in valve.

D
.....1
NL
.....6
PL
.....11
P
.....16
BG
.....21
CN
.....26
GB
.....2
S
.....7
UAE
.....12
TR
.....17
EST
.....22
UA
.....27
F
.....3
DK
.....8
GR
.....13
SK
.....18
LV
.....23
RUS
.....28
E
.....4
N
.....9
CZ
.....14
SLO
.....19
LT
.....24
I
.....5
FIN
...10
H
.....15
HR
.....20
RO
.....25
DESIGN + ENGINEERING
GROHE GERMANY
www.grohe.com
19 839
19 822
19 825
99.790.031/ÄM 219326/10.11
English .....1
Français .....8
Español ...15
I
S.v.p remettre cette instruction à l'utilisateur de la robinetterie!
Entregue estas instrucciones al usario final de la grifería!
Please pass these instructions on to the end user of the fitting!
I
Type #1
19 822
Type #2
19 825
Type #3
19 839
II II
Type #1
19 822
Type #2
19 825
Please pass these instructions on to the end user of the faucet!
without bypass use with use of integrated
Thermostat trim type #1 (single use)
bypass
Thermostat trim type #2 (integrated two way diverter)
Installation options with different types of trims
1
separate volume controls required
Thermostat trim type #3 (high flow)
Installation options with different types of trims
2
3
English
General Application
These trims are for use with the GrohFlex
TM
universal rough-in
valve.
Planning of piping is done at the time of the rough installation.
3 different types of thermostat mixers are possible.
Observe the possible combinations, see Pages 1 and 2.
Specification
Integral service stops
Flow pressure:
- min 1 bar or 14.5 psi
- recommended 1-5 bar or 14.5 – 72.5 psi
greater than 5 bar or 72.5 psi, fit pressure reducing valve
Max. operating pressure 8.5 bar or 125 psi
Max. test pressure 34.5 bar or 500 psi
Flow rates at 3 bar or 45 psi
- Type #1 (19 822) and Type #2 (19 825)
bottom outlet 24 l/min or 6,3 gpm
top outlet 12 l/min or 3,2 gpm
- Type #3 (19 839) 51 l/min or 14 gpm
Temperature
- max. (hot water inlet) 80 °C or 180 °F
Water connection: cold - RH
hot - LH
General preparation
1.Cut of the excess blue box material, see Fig. [1].
2.Seal the rough-in valve, see Fig. [2].
3.Close the integrated service stops, see Fig. [3].
4.Remove flush cap, see Fig. [4].
1
2
3
4
4
English
Installation Type #1 and Type #2
Attention for type #1
If both rough-in outlets are used, you have to install a spout
with diverter. If only the lower rough-in outlet is used, you
have to install a spout without diverter.
Installation
1.Install control unit and secure with screws, see Fig. [5].
2.Close water flow by turning the yoke. The mark (A) must be
on top, see Fig. [6].
3.Open the hot and cold integrated service stops, see Fig. [6].
4.While installation observe the right mounting position.
5.For installation of handle parts after adjustment, see Figs. [7]
and [8].
If the thermostat has been installed at too great a depth,
this can be adjusted by 27mm or 1 1/16“ with an extension set
(see Page II, ref. No. 47 822).
Adjustment
Temperature setting, see Fig. [9].
Before the mixer is put into service, if the mixed water
temperature measured at the point of discharge varies from
the specified temperature set on the thermostat handle.
After any maintenance operation on the thermostatic
cartridge.
Valve is closed with lever (B) in vertical position:
Open volume control by turning the lever (B).
1.Measure the temperature of the water emerging with a
thermometer.
2.Turn regulation nut (C) until the water emerging has reached
a temperature of 38 °C or 100 °F.
Reversed union (hot on right - cold on left). Replace
thermostatic cartridge, special cartridge for service is:
Ref. No.: 47 175 (1/2").
6
A
8
9
38 °C
100 °F
C
B
5
English
Installation Type #3
1.Install control unit and secure with screws, see Fig. [5].
2.Open the hot and cold integrated service stops, see Fig. [6].
3.While installation observe the right mounting position.
4.For installation of handle parts after adjustment, see Fig. [7].
Adjustment
Temperature setting, see Fig. [8].
Before the mixer is put into service, if the mixed water
temperature measured at the point of discharge varies from
the specified temperature set on the thermostat handle.
After any maintenance operation on the thermostatic
cartridge.
One or more separate volume controls (D) (not supplied) are
required to control the water flow, see Fig. [8].
Open volume control by turning the lever (D), see Fig. [8].
1.Measure the temperature of the water emerging with a
thermometer.
2.Turn regulation nut (C) until the water emerging has reached
a temperature of 38 °C or 100 °F.
Reversed union (hot on right - cold on left). Replace
thermostatic cartridge, special cartridge for service is:
Ref. No.: 47 186 (3/4”).
6
C
D
38 °C
8
100 °F
6
English
Type #2
19 825
F
E
B
10b
F
B
Temperature limitation
When in proper calibration, the temperature range is limited
to 43 °C or 110 °F. There is a first safety stop at 38 °C
or 100 °F. If a higher temperature is desired, one can
exceed 38 °C or 100 °F by overriding the safety stop. Press
the safety stop button (E).
Operation
Type #1, see Fig. [10a].
Turn lever (F) left or right:
- Select hot or cold water flow.
Turn lever (B) to the right:
- Open water outlet as pipeline installation is prepared.
- If a spout with diverter is installed, outlet to bath and shower
is possible.
Type #2, see Fig. [10b].
Turn lever (F) left or right:
- Select hot or cold water flow.
Turn lever (B) left or right:
Open water outlet as pipeline installation is prepared.
- left open to top outlet
- right open to bottom outlet
Type #3, see Fig. [10c].
Turn lever (F) left or right:
- Select hot or cold water flow
Type #1
19 822
F
E
B
10a
F
B
Type #3
19 839
F
E
10c
7
English
Prevention of frost damage
When the domestic water system is drained, the thermostat
mixers must be drained separately, since non-return valves
are installed in the hot and cold water connections.
The complete thermostat assembly and non-return valves
must be disassembled and removed.
Maintenance
Important note: If the control unit is to be removed from
the rough-in for servicing, first close the inlet stops then
open the flow control to allow any internal pressure to be
released from within the unit.
Inspect and clean all parts, replace if necessary and grease
with special valve grease.
Close the integrated service stops!
I. Non return valves, see Figs. [11] and [12].
Install in reverse order.
Open the integrated service stops!
Replacement parts, see page II (* = special accessories).
Care
Instructions for care of this faucet will be found in the Limited
Warranty supplement.
11
12
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

GROHE 19 822 User manual

Category
Faucets
Type
User manual
This manual is also suitable for

GROHE 19 822 is a thermostat mixer with a variety of features and possible use cases. It has two integrated service stops, a flow pressure of 1-5 bar, and a maximum operating pressure of 8.5 bar. The flow rates at 3 bar are 24 l/min for the bottom outlet and 12 l/min for the top outlet. The temperature range is limited to 43 °C or 110 °F, with a first safety stop at 38 °C or 100 °F. The GROHE 19 822 is suitable for use with the GrohFlexTM universal rough-in valve.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI