Sanyo DP50747 Owner's manual

Brand: Sanyo

Model: DP50747

Category: Plasma TVs

Type: Owner's manual

Model No.:

No. de Modelo:

de modèle :

Printed in U.S.A. SMC, March 2008

Impreso en U.S.A. SMC, marzo 2008

Imprimé aux. É-U SMC, mars 2008

Part No. / No. de Parte / N

de piece : 1JC6P1P0257B-

Plasma HDTV

Owner’s Manual

ENGLISH

Table of Contents . . . . 3

HDTV de Plasma

Manual de Instrucciónes

ESPAÑOL

Contenido . . . . . . . . . 19

TVHD plasma

Manuel d’instructions

FRANÇIAS

Table des matières . . 36

Need assistance?

Visit our Web site at

www.sanyoctv.com

or call toll free

1-800-877-5032

We can Help!

DP50747

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades with

one wider than the other. A grounding-type plug has two

blades and a third grounding prong. The wide blade or the

third prong are provided for your safety. If the provided

plug does not fit fully into your outlet, consult an electri-

cian for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or

pinched particularly at plugs, convenience receptacles,

and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the

manufacturer.

12. Use only with the cart, stand,

tripod, bracket, or table specified

by the manufacturer, or sold with

the apparatus. When a cart is

used, use caution when moving

the cart/apparatus combination to

avoid injury from tip-over.

13.Unplug this apparatus during lightning storms or when

unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing

is required when the apparatus has been damaged in any

way, such as power-supply cord or plug is damaged, liquid

has been spilled or objects have fallen into the apparatus,

the apparatus has been exposed to rain or moisture, does

not operate normally, or has been dropped.

15. If an outside antenna is connected to the television

equipment, be sure the antenna system is grounded so

as to provide some protection against voltage surges

and built up static charges. In the U.S. Selection 810-21

of the National Electrical Code provides information with

respect to proper grounding of the mast and supporting

structure, grounding of the lead-in wire to an antenna

discharge unit, size of grounding conductors, location of

antenna discharge unit, connection to grounding elec-

trodes, and requirements for the grounding electrodes.

16. An outside antenna system should not be located in the

vicinity of overhead power lines or other electrical light

or power circuits, or where it can fall into such power

lines or circuits. When installing an outside antenna

system, extreme care should be taken to keep from

touching such power lines or circuits as contact with

them might be fatal.

17. Wall or Ceiling Mounting—The product should be

mounted to a wall or ceiling only as recommended by

the manufacturer.

18. "Apparatus shall not be exposed to dripping or splashing

and no objects filled with liquids, such as vases, shall be

placed on the apparatus."

19. Where the Mains plug is used as the disconnect device,

the disconnect device shall remain readily operable.

20. A warning that an apparatus with Class1 construction

shall be connected to a Mains socket outlet with a

protective earthing connection.

EXAMPLE OF ANTENNA GROUNDING ACCORDING

TO NATIONAL ELECTRICAL CODE, ANSI/NFPA 70

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR

BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A

RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.

THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND

MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THIS

UNIT.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE

TO RAIN OR MOISTURE.

IMPORTANT SAFETY INSTRUCTIONS

“Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to

Article 820-40 of the NEC that provides guidelines for proper grounding

and, in particular, specifies that the cable ground shall be connected to

the grounding system of the building, as close to the point of cable entry

as practical.”

Need help?

Visit our Web site at www.sanyoctv.com or Call 1-800-877-5032

Need help?

Visit our Web site at www.sanyoctv.com or Call 1-800-877-5032

Welcome to the World of Sanyo

Thank you for purchasing this Sanyo Plasma High-Definition Digital Television. You made an excellent

choice for Performance, Reliability, Features, Value, and Styling. If assistance is needed, please call

1.800.877.5032 or visit our website at www.sanyoctv.com. We can help!

POWER REQUIREMENT:

Source: AC 120V, 60Hz

AC POWER CONSUMPTION: 420 Watts

Trademarks Information:

Manufactured under license from Dolby Labo-

ratories.

“Dolby” is a trademark of Dolby Laboratories.

SPECIFICATIONS

“As an ENERGY STAR

Partner,

Sanyo Manufacturing Corpora-

tion has determined that this

product meets the ENERGY STAR

guidelines for energy efficiency.”

CAUTION: FCC Regulations state that improper

modifications or unauthorized changes

to this unit may void the user’s author-

ity to operate the unit.

CONTENTS

IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . 2

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

HANDLING PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . 4

REMOVING THE STAND

(OPTIONAL) . . . . . . . . . . . . . . . . . 4

WALL MOUNTING

(OPTIONAL) . . . . . . . . . . . . . . . . . . . . . . 4

POSITIONING PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . 4

PROTECTING THE PLASMA SCREEN . . . . . . . . . . . . . . . . 4

GETTING STARTED

(REQUIRED INITIAL SETUP) . . . . . . . . . 5

Battery Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Antenna Connections to off-air or cable . . . . . . . . . 5

Connect AC Power Cord . . . . . . . . . . . . . . . . . . . . . . 5

Perform All Channel Search . . . . . . . . . . . . . . . . . . . 5

HDTV SIDE AND BACK PANELS . . . . . . . . . . . . . . . . . . . . 6

DIGITAL AV CONNECTIONS

HDMI Input Connection . . . . . . . . . . . . . . . . . . . . . . . 7

HD DVD Player / Game System . . . . . . . . . . . . . . . . 7

Set-top Box with DVI Output . . . . . . . . . . . . . . . . . . . 7

VIDEO2/3 COMPONENT JACKS CONNECTION

Digital Device Connection . . . . . . . . . . . . . . . . . . . . . 8

DIGITAL AUDIO OUT CONNECTION

Multichannel Receiver . . . . . . . . . . . . . . . . . . . . . . . . 8

ANALOG AUDIO OUT CONNECTION

Stereo Amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

VIDEO1 ANALOG AV CONNECTIONS . . . . . . . . . . . . . . . . 9

VCR (or other analog device) . . . . . . . . . . . . . . . . . . . 9

REMOTE CONTROL OPERATION . . . . . . . . . . . . . . . . . . . 10

MENU OPERATION—

How to Operate the On-Screen Menu . . . . . . . . . . . . . . 11

Menu Navigation Map . . . . . . . . . . . . . . . . . . . . . . . 11

Menu Options:

Digital Cable Search (Optional) . . . . . . . . . . . . . . . . 12

Digital Add-On Search . . . . . . . . . . . . . . . . . . . . . . . 12

Channel Scan Memory . . . . . . . . . . . . . . . . . . . . . . . 12

Picture/Sound Adjustment . . . . . . . . . . . . . . . . . . . . 13

Digital Caption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

V-Guide (Parental Control)

V-Guide Operation . . . . . . . . . . . . . . . . . . . . . . . . .14

V-Guide Operation

(Advanzed) . . . . . . . . . . . . . . . .15

Picture Rotation (Screen Saver) . . . . . . . . . . . . . . . 16

Energy (Power) Saver . . . . . . . . . . . . . . . . . . . . . . . . 16

White Pattern (Panel Repair) . . . . . . . . . . . . . . . . . . 16

HELPFUL HINTS

(Problems / Solutions) . . . . . . . . . . . . . . . 17

WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

This symbol on the nameplate means the product is Listed by Under-

writers’ Laboratories Inc. It is designed and manufactured to meet rigid

U.L. safety standards against risk of fire, casualty and electrical hazards.

Need help?

Visit our Web site at www.sanyoctv.com or Call 1-800-877-5032

HANDLING PRECAUTIONS

•

Handle the Plasma HDTV carefully when

installing. Do Not Drop.

•

Throughout the installation process, han-

dling by more than two people is

recommended.

•

When removing the stand, use a working

space that’s larger than the screen size. The

work surface must be flat, covered with a soft

cloth or blanket to protect the screen surface.

•

Before placing the Plasma HDTV face down,

make sure there are no objects under the

screen. Leaving any object may cause

damage on the screen surface.

POSITIONING PRECAUTIONS

•

Place this Plasma HDTV as indicated here. Failure

to do so may result in a fire hazard. Allowing the

proper amount of space at the top, sides, and

rear of the Plasma HDTV cabinet is critical for

proper air circulation and cooling of the unit. The

dimensions shown here indicate the minimum

space required. If the Plasma HDTV is to be built

into a compartment or similarly enclosed, these

minimum distances must be maintained.

•

Do not cover the ventilation slots on the Plasma

HDTV. Heat build-up can reduce the life of your

Plasma HDTV, and can also be dangerous.

•

If Plasma HDTV is not to be used for an extended

period of time, unplug it from the power outlet.

PROTECTING THE PLASMA SCREEN

The screen can be damaged if it is not maintained

properly. Do not use hard objects such as hard

cloth or paper. Do not use excessive pressure

when cleaning the screen,

as it can cause permanent

discoloration or dark spots.

NEVER spray liquids on the

screen.

REMOVING THE STAND (Optional)

Tools Needed: Phillips screwdriver

IMPORTANT NOTE:

Place HDTV face down on a

padded or cushioned surface that is larger than

the screen size to protect the screen and

finish. Handling by more than two people is

recommended.

Remove four (4) screws from the metal bracket.

CAUTION: Hold the stand firmly as you

remove the last screw.

Carefully remove the stand.

WALL MOUNTING (Optional)

Use the screws that are threaded into four (4) of

the six (6) inserts on the back of your Plasma

HDTV to secure it to a wall mounting kit.

UNIVERSAL standard interface:

480 x 200 and 480 x 360

Note: Wall Mounting kit is not supplied.

Mounting screws measurements:

M6 Diameter, Length—14mm (min.) 18mm (max.)

Need help?

Visit our Web site at www.sanyoctv.com or Call 1-800-877-5032

GETTING STARTED (REQUIRED INITIAL SETUP)

Connect AC Power Cord (supplied) to the

Plasma HDTV and electrical outlet as

shown here:

The AC outlet must be

near this equipment and

must be easily accessible.

Perform “All Channel Search.” The All

Channel Search will search for off-air digital

and analog channels, and analog cable

channels. The HDTV can receive cable or

off-air channels, but not at the same time.

To 120 V AC outlet.

INITIAL ON-SCREEN

ALL CHANNEL SEARCH

Press the POWER key. (Follow on-screen

instructions).

ANALOG CHANNELS

NOTE: If EXIT is pressed, the HDTV will skip Channel

Search and tune to Video1 without storing any

channels in the Channel Map database.

To POWER CORD

CONNECTOR on

back of Plasma

HDTV.

DIGITAL CHANNELS



Install supplied batteries in the Remote.

”AAA” eneloop Ni-MH rechargeable batteries)

PRECAUTIONS

Do not use rechargeables together with

dry cells, other types, mixed new and old,

or batteries with different charge levels.

Do not expose the Remote or batteries

to moisture or heat.

Match the “+” and “–” signs on the batteries with marks

inside the Remote Control.

For eneloop battery recharging, please refer to your

battery charger’s instructions

(battery charger not included).

Please recycle used up rechargeable batteries.

For more information visit: www.eneloopusa.com

Antenna Connection for off-air signals.

THE TUNER IN THIS HDTV CAN RECEIVE :

a. Digital and Analog off-air signals from an

antenna.

b. Analog or ClearQAM cable channels from a

direct Cable TV connection.

NOTES: You must use the on-screen

Search for ClearQAM Cable channels.

For the best picture, connect your Cable box

or Satellite receiver to HDMI1, 2, 3, or com-

ponent jacks (Video2 or 3).

This HDTV can receive ANY unscrambled RF

signal being broadcast.

ANTENNA

CABLE

ANALOG / DIGITAL

ANTENNA IN

If after two searches

the HDTV still fails to

detect any channels,

the HDTV will tune to

Video1.

Need help?

Visit our Web site at www.sanyoctv.com or Call 1-800-877-5032

HDTV SIDE AND BACK PANELS

SIDE PANEL

Volume

+ – keys

Channel

 keys

Power

key



 





 



 Analog / Digital Antenna Input, PAGE 5—

Connect an RF antenna or Analog Cable

system to this jack.

 HDMI INPUT 1/2/3 (High-Definition Multi-

media Interface), PAGE 7—An all digital AV

interface that accepts uncompressed video

signals for the very best picture possible.

HDMI supports HDCP copy protection, allow-

ing transmission of copy-protected digital

content. The signal can also include Dolby

Digital or PCM audio, when available. HDMI

(DVI) INPUT 1 jack is compatible with DVI

equipped AV devices. (Separate audio con-

nection and an adapter are required for DVI

device.)

 Analog Audio Out (L/R) Jacks, PAGE 9—

Connect external audio equipment here.

 Component Video Input (VIDEO 2 or

VIDEO 3), PAGE 8—Connect digital video

equipment to the Y (Green), Pb (Blue), Pr (Red)

and Audio L / R jacks. These jacks automati-

cally detect the type of signal being received.

 Audio/Video Input (VIDEO 1), PAGES 9—

Connect analog video equipment here.

NOTE: S-Video connection overrides the (Video 1)

composite video connection.

 Digital Audio Output, PAGE 8—Use a Phono-

Type Digital Audio Out Cable to connect

Digital Audio Output to an advanced stereo

home theater system equipped with Dolby

Digital 5.1.



S-Video Input (VIDEO 1), PAGE 9—To enhance

video detail use the S-Video jack instead of the

Video jack, if available on your external equip-

ment. (S-Video connection will override

connection to the VIDEO 1 input jack.)

 Service Jacks—For production use only.

 AC IN 120V—Connect power cord here.

(See page 5.)

HDTV

BACK PANEL

Need help?

Visit our Web site at www.sanyoctv.com or Call 1-800-877-5032

DIGITAL AV CONNECTIONS—

Receiving the Ultimate Picture

OPERATING TIPS:

 Press the INPUT key after connecting cables to

access the AV Inputs. There is NO need to tune

to a blank channel.

 HDMI INPUT 2, and 3 jacks have identical func-

tions with HDMI INPUT 1 having an additional

feature for DVI connection. Compatible video

devices can be connected to either set of jacks.

 Use HDMI (DVI) INPUT 1 to connect your DVI

device, make sure you connect Audio out to the

HDTV’s VIDEO 3 Audio In.

 The VIDEO 3 audio jacks are used to receive the

audio from the DVI device. These video jacks

cannot be used when a DVI device is connected.

Connect the Set-top Box (STB) DVI Output

to the HDTV’s HDMI INPUT 1.

NOTE: Check with your local electronics store for a DVI

to HDMI Adapter Cable that matches your

equipment and the HDTV.

Connect the STB Audio out to the HDTV’s

VIDEO3 Audio In L / R

Press INPUT to select HDMI 1 and view the

digital program.

IMPORTANT FACT:

Only the HDMI (DVI) INPUT 1 jack

can accept a DVI (digital video interface) connection.

DVI TO HDMI INPUT 1 JACK CONNECTIONS

HDMI TO

DVI CABLE

AUDIO

CABLE

(Cables not

supplied.)

BACK VIEW OF HDTV

SET-TOP BOX or similar device

HDMI INPUT 2/ INPUT 3 JACKS

CONNECTIONS

Connect compatible Digital devices, such as, an

HD Cable Box, HD Satellite Receiver, DVD Player,

and Game System

Connect the external equipment’s HDMI

Output to a HDTV HDMI Input.

Press INPUT to select HDMI 2 or HDMI 3 to

view the digital program.

BACK VIEW OF HDTV

(HDMI INPUT 2 / HDMI INPUT 3)

GAME

SYSTEM

REMOTE CONTROL

DVD PLAYER or

similar device

INPUT

(Cables not

supplied.)

Need help?

Visit our Web site at www.sanyoctv.com or Call 1-800-877-5032

SET-TOP BOX, DVD PLAYER

or similar device

GREEN, BLUE, RED JACKS

OPERATING TIPS:

 Press the INPUT key after connecting cables

to access the AV Inputs. There is NO need to

tune to a blank channel.

 You DO NOT need to tune the HDTV to

Channel 3 or 4 to view a DVD source.

BACK VIEW OF HDTV

PHONO-TYPE

DIGITAL AUDIO

OUT CABLE

(Not supplied)

MULTICHANNEL RECEIVER

BACK VIEW

OF HDTV

(VIDEO 3)

AUDIO L/R

JACKS

BACK VIEW

OF HDTV

(VIDEO 2)

AUDIO L/R

JACKS

GAME SYSTEM

Connect a Component Cable to the VIDEO 2 / 3

set of Green, Blue, and Red video jacks. (com-

ponent cable not included)

Connect an Audio Cable to the VIDEO 2 / 3

White and Red audio jacks. (audio cable not

included)

Press INPUT to select Video 2 or Video 3 to

view the program.

NOTE: VIDEO 2 and VIDEO 3 jacks have identical

functions. Compatible video devices can be

connected to either or both jacks.

VIDEO 2 & 3 COMPONENT: GREEN,

BLUE, RED—

An Exceptional Picture

Connect Digital devices, such as an HD Cable

Box, HD Satellite Receiver, DVD Player, and

Game System

Connect a Multichannel Receiver to the HDTV

Digital Audio Output as shown.

Note: Dolby

Digital 5.1 audio is available at the Digital

Audio Output only when received as part of a

Digital Antenna signal being viewed on the

screen.

DIGITAL AUDIO JACK

CONNECTING A MULTICHANNEL RECEIVER

TO THE HDTV

GREEN, BLUE,

RED JACKS

IMPORTANT FACT:

To view available High-Definition

(HD) sources in true HD, you must connect your HD

equipment to the Component or HDMI jacks.

Need help?

Visit our Web site at www.sanyoctv.com or Call 1-800-877-5032

ANALOG DEVICE

JACKS

S-VIDEO

JACK

(OPTIONAL)

HDTV AV (VIDEO 1) INPUT JACKS

Connect a Composite Cable to the VIDEO1

Yellow, White, and Red AV jacks as shown.

OPTIONAL

Connect analog device to the HDTV S-Video

In Jack, if S-Video output is available on your

external analog device.

NOTE: S-Video jack connection overrides a Video jack

connection (VIDEO 1).

Press INPUT to select Video 1 to view the

DVD or VCR program.

IMPORTANT FACTS:

Don’t be confused by the phrase “Available in

High-Definition.”

Composite jacks offer only 480i

(SDTV) resolution.

BACK VIEW OF HDTV

OPERATING TIPS:

 Position your HDTV at least 2 feet from stereo

speakers. The magnets in the speakers may

affect the picture quality.

 For Mono VCR (Single Audio Jack), connect

VCR Audio Out to HDTV Audio (L) Input.

 “No Signal” will appear randomly on the

screen when no signal is detected at the

VIDEO1 video jack.

Connect a Stereo Amplifier to the HDTV Audio

Out jacks as shown.

NOTE:

Do not

connect external speakers directly to

the HDTV.

CONNECTING A STEREO

AMPLIFIER TO THE HDTV

AUDIO OUT JACKS (FIXED ANALOG)

VIDEO 1 (COMPOSITE-YELLOW)—

A Good Picture

or (S-VIDEO)—

A Better Picture

Connect an analog device, such as, an Analog

Cable Box, Satellite Receiver, or VCR

STEREO AMPLIFIER

(Cables not

supplied.)

(Cable not

supplied.)

Need help?

Visit our Web site at www.sanyoctv.com or Call 1-800-877-5032

REMOTE CONTROL OPERATION



Audio Key—Press to select the desired audio

mode, if available.



Sleep Key—Press SLEEP then “0” to set the

Off Timer. Off time can be set in 30-minute

increments up to 3 hours.

NOTE:The Off Timer cancels if the TV is turned off or if

a power failure occurs.

Caption Key—Press to select mode options:

Digital CC1 ~ CC6, or Analog CC1 ~ CC4,

QuikCap, or OFF. (QuikCap turns captions on

or off with the Mute function.) Digital Captions

can be changed using the menu settings.

Volume Keys—Press VOL – + to increase or

decrease the audio volume.

1– – Key—For Cable channels above 99, press

this key, then press the other two numbers.

Mute Key—Press to mute or restore the sound.



PIX Shape Key—Press to choose between

options Pix1 ~ Pix4. Available options depend

on the signal and the broadcast’s aspect ratio.



Input Key—Press to select the source to

view: Analog RF, Digital RF, Video 1, Video 2,

Video 3, HDMI 1, HDMI 2, or HDMI 3.



Info Key—Press to display Channel Banner

information.

Digital Antenna Banner may contain: Tuner

ID, Channel Number, Station ID, Program

Rating, Signal Strength, Detailed Program

Info, Audio Information, & Program Title.

Analog Antenna Banner may contain: Tuner

ID, Channel Number, Station ID, Program

Rating, & Audio Information.

Cable Banner may contain: Tuner ID,

Channel Number, Station ID (analog only),

Program Rating, Signal Strength, & Audio

Information.



Reset Key—Press this key twice to restore

factory settings. The TV will automatically start

Channel Search and clear customized settings.

NOTE:The Channel Scan Memory database will be

replaced.



Number Keys—Press two keys to select a

channel. Example: Press 0 then 6 to select

channel 6. (See #13.)



Channel Scanning (CH ) Keys—Press to

scan through the channels in memory.



Recall Key—Press to switch between the last

two channels selected.



Menu Navigational Keys:

Menu—Press to display on-screen menu.

Cursor  (up)  (down) keys—Press these

keys to move the cursor up and down.

Cursor < (left) > (right) keys—Press these

keys to move the cursor left and right.

Enter Key—Press to select an option from

the menu system, when required.

Exit Key—Press to exit from the menu.

















Point

towards HDTV







Need help?

Visit our Web site at www.sanyoctv.com or Call 1-800-877-5032

ON-SCREEN MENU OPERATION

MENU NAVIGATIONAL MAP

MAIN SUB MENUS

All Channel Search

Yes

Analog Antenna Signal

Cable

VHF/UHF

Channel Scan Memory

Delete?

Add?

Auto

English

Español

Color

Tint

Contrast

Brightness

Sharpness

Tone

Picture Rotation

Off

White Pattern

V-Guide

Off

Yes

Digital Add-on Search

Digital Cable Search

Font Size

Font Style

Background Color

Foreground Color

Background Opacity

Foreground Opacity

Digital Caption

Picture/Sound

• Manual

Menu Language

Français

Off

Low

Energy Saver

High

• On

Adjust

Off

HOW TO OPERATE THE MENU

NOTES: Some Menu options are specific to Digital

and/or Analog signals. To access these

options, you must first tune the HDTV to a

digital or analog channel.

“Not available”

will be displayed on the

screen if an unavailable menu option is

selected.

Press the MENU key to display the Main

menu.

Use the CURSOR  keys to highlight menu

item.

Use the CURSOR < > keys to select or adjust

menu item.

Press ENTER to activate setting, if needed.

When you have finished making adjustments,

press the

EXIT key to return to normal TV

viewing.

NOTE: For menu items that have sub menus, follow

on-screen instructions to select and make

adjustments.

Need help?

Visit our Web site at www.sanyoctv.com or Call 1-800-877-5032

IMPORTANT FACTS:

This HDTV maintains only one

database of digital channels. Therefore, when you

search for cable channels, the database of antenna

digital channels will be deleted. You will be able to

receive only those ClearQAM channels your cable

company provides.

To restore the antenna digital channel database,

reconnect the antenna and use the menu system to

perform an All Channel Search.

DIGITAL CABLE SEARCH (OPTIONAL)

This HDTV can receive unscrambled (ClearQAM)

digital cable channels, when available. However,

not all cable companies provide ClearQAM

digital channels.

Digital Cable Search process will take about 10

minutes, please be patient.

DIGITAL ADD-ON SEARCH

To add new digital channels to the existing

antenna channel database, use Digital Add-on

Search. Also, use this feature to add channels

when broadcast towers are in multiple directions

from your location.

For more info go to www.antennaweb.org and

type in your zip code to obtain specific tower

and antenna information. Then adjust your

antenna and

repeat the

Digital Add-

on Search.

CHANNEL SCAN MEMORY

This is a list of active channels that you can scan

through using the Channel  (up) and CH 

(down) keys. The list can be customized by delet-

ing and/or adding channels as shown.

IMPORTANT FACTS:

When a digital channel is

deleted, all of that channel’s sub-channels are

deleted as well.

Only previously deleted digital channels can be

added back to the Channel Scan Memory.

If one digital sub-channel is added back to the

Channel Scan Memory list, all of that channel’s sub-

channels will be added back.

This Display

appears after

you press

ENTER.

After 3 seconds the TV screen

will display “Add?”

This Display

appears after

you press

ENTER.

After 3 seconds the TV screen

will display “Delete?”

Need help?

Visit our Web site at www.sanyoctv.com or Call 1-800-877-5032

PICTURE / SOUND ADJUSTMENT

Choose Auto to accept predetermined values for

each parameter.

Choose Manual to adjust Picture / Sound values

individually to suit your personal preferences.

ADJUSTING THE PICTURE / SOUND MANUALLY

Use the CURSOR  keys to highlight

Picture / Sound. Press ENTER.

Use the CURSOR  keys to highlight

Manual. Press ENTER.

ADJUSTING THE PICTURE / SOUND LEVELS

Use the CURSOR  keys to highlight Color,

Tint, Contrast, Brightness, Sharpness, or Tone.

Use the CURSOR < > keys to adjust the levels.

DIGITAL CAPTIONING

Captioning is textual information transmitted

along with the picture and sound. Turning Cap-

tioning ON causes the HDTV to open these

captions (digital or analog) and superimpose

them on the screen. (Local broadcasters decide

which caption signals to transmit.)

Digital Captions can be changed using the menu

settings as shown.

Use the CURSOR  keys to highlight Digital

Caption. Press ENTER.

Use the CURSOR  keys to select the option

you want to adjust.

Use the CURSOR <>keys to adjust the value.

NOTES: If Background Opacity is set to transparent,

captions may be difficult to see. x

Only true EIA 708B Digital Closed-

Captions are affected by all of these

settings.

Need help?

Visit our Web site at www.sanyoctv.com or Call 1-800-877-5032



STANDARD V-GUIDE RATINGS—AT-A-GLANCE

MPAA (Movie) RATING

BLOCKED RATINGS

(Lock symbol)

TV RATING

CONTENT RATING

V-GUIDE (PARENTAL CONTROL)

NOTE: THIS FEATURE IS DESIGNED TO COMPLY

WITH THE UNITED STATES OF AMERICA’S FCC

V-CHIP REGULATIONS. THEREFORE, IT MAY

NOT FUNCTION WITH BROADCASTS THAT

ORIGINATE IN OTHER COUNTRIES.

This Sanyo television is equipped with an elec-

tronic V-Chip to interpret MPAA (Motion Picture

Association of America) and TV Parental Guide-

lines rating codes. When these codes are

detected, the HDTV will automatically display or

block the program, depending upon choices you

make when setting up the V-Guide system.

Use this feature to automatically block programs

with content you deem as inappropriate for your

children to view.

MORE INFORMATION

Additional information about MPAA and V-Chip

rating can be found at: www.mpaa.org and

www.v-chip.org, respectively.

V-GUIDE OPERATION

Use the CURSOR  keys to highlight

V-Guide in the Main menu. Press ENTER.

Use the CURSOR  keys to highlight On,

in the V-Guide menu. Press ENTER.

Use the CURSOR  keys to highlight

Adjust. Press ENTER.

Use the CURSOR  and < > keys to select

MOVIE, TV, or Content Ratings.

NOTE:Content ratings are under the letters FV, D, L,

S, and V.

Press the ENTER key to Block or Unblock

selected rating. A lock symbol will appear

beside the selected rating option indicating

that it is blocked

OPERATING TIPS

 V-Guide settings are effective for Analog

channels, Digital channels and Video1 signals.

 You can block portions of a TV rating by

choosing one or more of the Content ratings

(D, L, S, and V). By blocking just the L and S

content ratings of TV-14, for example, TV-14

rated programs with a D and/or V content

rating could still be viewed.

Need help?

Visit our Web site at www.sanyoctv.com or Call 1-800-877-5032



REGIONAL V-GUIDE RATINGS (ADVANCED)

V-Chip Regional Ratings 5 (RRT5) is an advanced

V-Chip ratings system for digital channels that

are received with an antenna. Your new Sanyo

HDTV supports this alternative system.

When the HDTV detects compatible RRT5 data, it

is downloaded and stored in memory and the

menu is modified to include an advanced adjust-

ment option.

When the Adjust (Advanced) setup option is

selected the Advanced Rating screen appears.

Use the CURSOR  keys to highlight

V-Guide in the Main menu. Press ENTER.

Use the CURSOR  keys to highlight On,

in the V-Guide control menu. Press ENTER.

Use the CURSOR  keys to highlight

Adjust (Advanced). Press ENTER.

Use the CURSOR  and < > keys to select

a rating.

HINT: There may be more ratings than can be displayed

on one screen. When vertical scroll bars appear,

use the

CURSOR

 keys to gain access to the

additional ratings.

Press the ENTER key to Block or Unblock

selected rating. A Lock symbol will appear

beside the selected rating option indicating

that it is blocked.

The advanced rating table will reflect previous

choices you may have made.

NOTE:If the HDTV is reset to factory defaults or if a

Manual Cable Search is performed, only the

Adjust option will appear in the menu. The

Adjust (Advanced) option will reappear when the

HDTV again detects RRT5 data.

The V-Guide ratings screen below is just an

example. Actual rating options will vary by

region. For example, the RRT5 ratings for San

Francisco, California may differ from those in

Little Rock, Arkansas.

Need help?

Visit our Web site at www.sanyoctv.com or Call 1-800-877-5032

ENERGY (POWER) SAVER

This power saving feature reduces the backlight

brightness level. The options are:

• OFF—power consumption is normal.

• LOW—power saving level is low and the back-

light brightness level is lower than normal.

• HIGH—power saving level is high and the back-

light brightness is set to the lowest level.

Use the CURSOR  keys to highlight

Energy Saver. Press ENTER.

Use the CURSOR  keys to select Off, Low,

or High.

NOTE:The Energy Saver settings level varies with

the Picture / Sound mode.

PICTURE ROTATION (SCREEN SAVER)

Displaying a still picture for a long time may cause

an “afterimage” or “ghost” on the screen. To neu-

tralize this situation, use Picture Rotation function.

Use the CURSOR  keys to highlight Picture

Rotation. Press ENTER.

Use the CURSOR  keys to select On or Off.

NOTE: When Picture Rotation is set to ON, the HDTV

automatically changes the display position every

15 minutes to avoid afterimage.

WHITE PATTERN (PANEL REPAIR)

Use feature to repair the Plasma screen.

If an afterimage occurs, use the White

Pattern feature immediately to repair the panel.

The more severe the afterimage, the longer the

curing process may take. It may be impossible to

repair all cases of afterimage burn.

The sooner you remove a still picture and activate

White Pattern, the more likely it is that the panel

can be repaired.

Use the CURSOR  keys to highlight White

Pattern. Press ENTER.

Use the CURSOR  keys to select On.

NOTES: When White Pattern is activated the screen will

instantly turn completely white. The On time is

automatically set for 30 minutes.

Pressing any key except VOLUME , MUTE,

and AUDIO will cancel the curing process and

return the HDTV to normal viewing.

Afterimage (or image burn) is not covered

under warranty.

Need help?

Visit our Web site at www.sanyoctv.com or Call 1-800-877-5032

Problem: Check these Conditions: Try these Solutions: Page No.

No picture, sound

(Digital Picture)



Check antenna/external connections



May be station trouble, NO signal

broadcast.



MUTE function may be on.



The Plasma HDTV takes a few seconds to

display an image.



Adjust antenna.



Try a different channel.



Press RESET key twice to restart channel

search (All customized settings will be

cancelled.)



Adjust Volume.

5, 10

No Captioning



Check if station is broadcasting a Closed-

Caption signal.



Select another channel.



Press CAPTION key to select captioning

mode.

Cannot customize

Caption



Digital Caption signal is not being

broadcast.



Press CAPTION key to select Analog

captioning.

10, 13

Cannot display pic-

ture on a full screen



Press PIX SHAPE key to change setting.

Poor Picture/Sound

(watching Analog)



Check if program is in color.



Check antenna/external connections.



Color or Tint misadjusted.



May be station trouble.



Maybe MUTE function is on.



Try a different channel.



Adjust antenna.



Press RESET twice key to restart channel

search.



Adjust Volume.

10, 13

“No Signal” message

appears on screen



Check Audio/ Video connections.



Check external equipment connections.



Check external equipment setting.



Check antenna connection.



Press INPUT key.



Switch on external equipment.



Turn antenna, install signal booster.



Set external equipment output connections

to match HDTV input connections.

7 – 10

Pixilation of Digital

image



Press INFO key and check signal

strength.



Turn antenna, install signal booster.



Install outdoor Digital antenna.

Cannot select or scan

some channels



Channel may be removed from memory.



Check antenna connections.



No digital signal being broadcast.



V-Guide is set to block programming.



Weak Signal.



Select

Channel Scan Memory

and manually

add channels or start channel search.



Set V-Guide to

“None”

or press RESET key

twice to clear all settings and restart

channel search.



Turn antenna, install signal booster.

14 – 15

No Cable channels

above number 13



Cable Channel Indicator C should appear

next to channel number.



Search for Cable channels using

Digital

Cable Search.

Remote Control

will not work TV



Check batteries.



Check if TV is plugged in.



Replace batteries.



Aim remote control at front of TV.

5, 10

Afterimages (ghosts)

appear



Do not display the same image on screen

for a long period of time. Afterimages or

ghosts may appear on parts of the panel.



Use the

Picture Rotation Screen Saver

function.



Use the

White Pattern

Feature to repair the

panel.

HELPFUL HINTS—Problems/Solutions

If you are having problems with your HDTV, check

this trouble shooting chart to find one or more

possible solutions.

Before returning your HDTV, please visit our

website at www.sanyoctv.com or call us

toll free at 1.800.877.5032.

We can Help!

Need help?

Visit our Web site at www.sanyoctv.com or Call 1-800-877-5032

For your protection in the event of theft or loss of this product, please fill in the information requested below

and KEEP IN A SAFE PLACE FOR YOUR OWN PERSONAL RECORDS.

Model No.______________________________ Date of Purchase _________________________

Serial No.______________________________ Purchase Price ___________________________

Where Purchased_________________________

(Located on back of unit)

Sanyo Manufacturing Corp.

3333 Sanyo Road, Forrest City, AR 72335

ONE-YEAR LIMITED PARTS AND LABOR WARRANTY

THIS LIMITED PARTS AND LABOR WARRANTY IS VALID ONLY ON SANYO TELEVISIONS PURCHASED AND USED IN

THE UNITED STATES OF AMERICA, CANADA, AND PUERTO RICO, EXCLUDING ALL OTHER U.S. TERRITORIES AND

PROTECTORATES. THIS LIMITED WARRANTY APPLIES ONLY TO THE ORIGINAL RETAIL PURCHASER, AND DOES NOT

APPLY TO PRODUCTS USED FOR INDUSTRIAL OR COMMERCIAL PURPOSES.

WARRANTY APPLICATION

FOR ONE YEAR from the date of original retail purchase Sanyo Manufacturing Corporation (SMC) warrants this TV to

be free from manufacturing defects in materials and workmanship under normal use and conditions for parts and labor.

For the FIRST 90 DAYS from the date of original retail purchase, Sanyo Manufacturing Corporation will replace any

defective TV via exchange at the retailer. To ensure proper warranty application, keep the original-dated-sales receipt

for evidence of purchase. Return the defective TV to the retailer along with the receipt and the included accessories,

such as the remote control. The defective TV will be exchanged for the same model, or a replacement model of equal

value, if necessary. Replacement model will be contingent on availability and at the sole discretion of Sanyo

Manufacturing Corporation.

THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES OF MERCHANTABILITY OR

FITNESS FOR A PARTICULAR PURPOSE.

OBLIGATIONS

For one year

from the date of purchase, Sanyo Manufacturing Corporation warrants this product to be free from

defects in material and workmanship under normal use and conditions. During the first 90 days

under this warranty

for any manufacturing defect or malfunction Sanyo Manufacturing Corporation will provide a new TV via exchange at

the retailer.

HOW TO MAKE A CLAIM UNDER THIS WARRANTY

Please call 1-800-877-5032. Please be prepared to give us the television’s model number and serial number when you

call. The model number and serial number are printed on a label attached to the back of the unit.

For customer assistance, call toll free 1-800-877-5032.

Weekdays 7:30 AM – 7:00 PM Central Time

Saturday 7:30 AM – 4:00 PM Central Time

This warranty expresses specific contractual rights; retail purchasers may have additional statutory rights which vary

from state to state.

(EFFECTIVE: March 1, 2007)

¿ Necesita ayuda?

Visite nuestro sitio en internet www.sanyoctv.com o Llame al 1-800-877-5032

BIENVENIDO AL MUNDO DE SANYO . . . . . . . . . . . . . . . 19

ESPECIFICACIONES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

IMPORTANTES MEDIDAS DE SEGURIDAD . . . . . . . . . . 20

QUITANDO EL PEDESTAL DE LA HDTV (Opcional) . . . .21

MONTAJE EN LA PARED (Opcional) . . . . . . . . . . . . . . . . 21

PRECAUCIONES DE POSICIÓN . . . . . . . . . . . . . . . . . . . . 21

PROTEGER LA PANTALLA DE PLASMA . . . . . . . . . . . . . 21

PARA EMPEZAR (AJUSTE INICIAL REQUERIDO) . . . . 22

Instalación de Baterías . . . . . . . . . . . . . . . . . . . . . . 22

Conexión de Antena para señales de aire . . . . . . 22

Conectando el Cordón de Potencia . . . . . . . . . . . . 22

Búsqueda de Todos los Canales . . . . . . . . . . . . . . . 22

PÁNELES DE LADO Y PARTE TRASERA . . . . . . . . . . . . . 23

CONEXIONES DIGITALES AV

Entradas HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Reproductor de DVD HD o Consola de Juego . . . 24

Dispositivo con Salida DVI . . . . . . . . . . . . . . . . . . . 24

CONECTORES COMPONENTE VIDEO 2 / 3

Dispositivos Digitales . . . . . . . . . . . . . . . . . . . . . . . . 25

CONECTANDO LA SALIDA DE AUDIO DIGITAL

Receptor Multicanales . . . . . . . . . . . . . . . . . . . . . . . 25

CONECTANDO LA SALIDA DE AUDIO ANÁLOGO

Amplificador Estéreo . . . . . . . . . . . . . . . . . . . . . . . . . 26

CONECTORES ANÁLOGOS AV VIDEO 1

Video Casetera VHS (u otro Aparato Análogo) . . . . 26

OPERACIÓN DEL CONTROL REMOTO . . . . . . . . . . . . . . 27

OPERACIÓN DE MENÚ

Cómo Operar el Menú en Pantalla . . . . . . . . . . . . . 28

Mapa de Navegación del Menú . . . . . . . . . . . . . . . 28

Opciónes de Menu:

Búsqueda de Canales de Cable Digitales . . . . . . .29

Búsqueda de Adición Digital . . . . . . . . . . . . . . . . . .29

Memoria de Canales . . . . . . . . . . . . . . . . . . . . . . . . . 29

Guía-V (Control Paternal) . . . . . . . . . . . . . . . . . . . . .30

Operación de Guía-V (Estándar) . . . . . . . . . . . . .30

Operación Guía-V Regional (Avanzado) . . . . . .31

Ajustes de imagen / sonido . . . . . . . . . . . . . . . . . . . .32

Ajustes Manuales de Imagen y Sonido . . . . . . .32

Ajustes Avanzados de Imagen y Sonido . . . . . .32

Caption Digital . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Ahorrador de Energía . . . . . . . . . . . . . . . . . . . . . . . . 33

Rotación de Imagen (Protector de Pantalla) . . . . 33

Imagen Blanca (Reparación del Panel) . . . . . . . . . 33

SUGERENCIAS ÚTILES (PROBLEMAS/SOLUCIONES) . . 34

GARANTÍA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

CONTENIDO

“Como un Asociado de ENERGY

STAR

,” Sanyo Manufacturing

Corporation, ha determinado

que este producto cumple con

los lineamientos en eficiencia

energética de ENERGY STAR

ESPAÑOL—MANUAL DE INSTRUCCIONES

Bienvenido al Mundo de SANYO

Gracias por comprar esta televisión digital Plasma HDTV. Usted ha hecho una excelente elección por Desempeño,

Confiabilidad, Características, Valor, y Estilo. Por favor visite nuestro sitio de internet

www.sanyoctv.com o llame

sin costo al

1.800.877.5032. Nosotros podemos ayudar!

Este símbolo impreso, significa que el producto esta listado por Underwriters’

Laboartories Inc. El diseño y manufactura de este producto, reúne los rígidos

estándares de U.L., contra riesgos de incendio, accidentes o descargas eléctricas.

ESPECIFICACIONES

Requerimientos de Potencia:

Fuente: AC 120V, 60Hz

Consumo de Potencia: 420 watts

Manufacturado bajo licencia de Dolby Labora-

tories. “Dolby ” el símbolo son marcas

re-gistradas de Laboratorios Dolby

PRECAUCIÓN: Regulaciones FCC indican que modi-

ficaciones inadecuadas o cambios no

autorizados a esta unidad, pueden

anular el derecho del usuario a

operar la unidad.

¿Necesita ayuda?

Visite nuestro sitio en internet www.sanyoctv.com o Llame al 1-800-877-5032

PRECAUCIÓN

RIESGO DE TOQUE ELECTRICO ¡NO ABRIR!

PRECAUCION : PARA REDUCIR EL RIESGO DE TOQUE ELÉCTRICO, NO QUITE LA CUBIERTA (O

LA TAPA TRASERA). NO HAY PARTES ADENTRO QUE LAS PUEDA REPARAR EL USUARIO.

REFIERASE A PERSONAL CALIFICADO PARA REPARAR EL APARATO.

ESTE SIMBOLO INDICA QUÉ VOLTAJES PELIGROSOS QUE CONSTI-

TUYEN UN RIESGO DE TOQUE ELECTRICO ESTAN PRESENTES DENTRO

DE ESTA UNIDAD.

ESTE SÍMBOLO INDICA QUE HAY INSTRUCCIONES IMPORTANTES DE

OPERACIÓN Y MANTENIMIENTO EN LA LITERATURA QUE SE ANEXA A

ESTA UNIDAD.

ADVERTENCIA : PARA REDUCIR EL RIESGO DE FUEGO O TOQUE ELÉCTRICO, NO EXPONGA ESTE

APARATO A LLUVIA O HUMEDAD.

IMPORTANTES MEDIDAS DE SEGURIDAD

1. Lea estas instrucciones.

2. Guarde estas instrucciones.

3. Preste atención a los avisos.

4. Siga todas las instrucciones.

5. No use este aparato cerca del agua.

6. Limpie sólo con un trapo seco.

7. No obstruya las aperturas para ventilación. Instale de

acuerdo a las instrucciones del fabricante.

8. No se instale cerca de ninguna fuente de calor como radi-

adores, registros de calor, estufas, u otros aparatos

(incluyendo amplificadores) que produzcan calor.

9. Por seguridad, no elimine la conexión de tierra de la clavija.

Una clavija polarizada tiene una hoja más ancha que la otra.

Una clavija de tipo conexión a tierra, tiene dos hojas y un

tercer conector mas prolongado. La hoja ancha o el conec-

tor prolongado están provistas para su seguridad. Si la

plaga o clavija proveída no asienta correctamente en el

contacto eléctrico, consulte a un electricista para que esa

toma de ac obsoleta sea remplazada.

10. Proteja el cordón de potencia de que sea pisado o

perforado, particularmente en las hojas y del punto donde

éste sale del aparato.

11. Sólo use anexos o accesorios especificados por el

fabricante.

12. Use únicamente con el carro, estante, tripie,

soporte o mesa especificada por el fabricante, o

vendida con el aparato. Cuando se use un carro,

tenga precaución cuando mueva la combinación

de carro/aparato para evitar lesiones en caso de

que se caiga.

13. Desconecte este aparato en caso de relampagueo o cuando

no se use por un periodo de tiempo prolongado.

14. Refiera todas las reparaciones a personal de servicio califi-

cado. Se requiere de servicio cuando el aparato se ha dañado

de cualquier forma, como si el cordón de potencia se dañara

de alguna forma, se ha derramado liquido sobre el aparato o

algún objeto le ha caído encima, el aparato se ha expuesto a

la lluvia o humedad, que no opere normalmente o que se

haya caído.

15. Si una antena externa se ha conectado al televisor,

asegurese que el sistema de tierra de la antena esté de

forma que provea alguna protección contra fugas de voltaje

o cargas electrostáticas. En la sección 810-21 del código

nacional eléctrico de lo Estados Unidos se menciona infor-

mación con respecto a la manera adecuada de instalar el

sistema de tierra al mástil principal, aterrizaje del cableado

para la unidad de descarga de la antena, tamaño de los con-

ductores de tierra, localización de la unidad de descarga

de la antena, conexión a los electrodos de tierra, y

requerimientos de los electrodos de tierra.

16. Un sistema de antena externo no debe instalarse cerca de

líneas de electricidad o circuitos de potencia o alumbrado, o

donde puedan caer sobre líneas de energía eléctrica o

circuitos cuyo contacto con ellos puede ser fatal.

17. Montaje en pared o techo—Este producto deberá de ser

montado en la pared o techo siguiendo las recomendaciones

del fabricante.

18. "Este aparato no deberá de ser expuesto a ser mojado, y no

se deberán de colocar recipientes con líquido encima de el."

19. Si el conector del cable de AC se usa como artículo de

desconexión principal, entonces este deberá de per-

manecer accesible todo el tiempo.

20. El adaptador de potencia de AC no debe de localizarse en

una area confinada. Se requiere la ventilación apropiada

para asegurar una operación confiable y protejerlo de

sobrecalentamiento.

EJEMPLO DE ATERRIZAMIENTO DE ANTENA DE ACUERDO

AL CÓDIGO NACIONAL ELÉCTRICO

(National Electrical Code, ANSI/NFPA 70)

“Nota al instalador del sistema de cable CATV :

Este recordatorio es dado para llamar la atención del instalador del

sistema de cable CATV al Articulo 820-40 del NEC que provee guias para

el aterrizamiento adecuado y, en particular, especifica que la tierra del

cable deberá de estar conectada al sistema de tierra del edificio, tan

cercano al punto de entrada del cable como sea practico.”

Page is loading ...

Sanyo DP50747 Owner's manual

Brand: Sanyo

Model: DP50747

Category: Plasma TVs

Type: Owner's manual

Download PDF

report

in other languages

français: Sanyo DP50747 Le manuel du propriétaire
español: Sanyo DP50747 El manual del propietario

Sanyo DP50747 Owner's manual

Sanyo DP50747 Owner's manual

in other languages

Related papers

Other documents