Ingersoll-Rand 88S Operation and Maintenance Manual

Type
Operation and Maintenance Manual

This manual is also suitable for

Ingersoll-Rand 88S sander is designed for demanding sanding and polishing applications where limited space is an issue. Read the brief product information below for familiarization with the device. For safety, top performance, and maximum durability of the parts, operate the tool at 90 psig (6.2 bar/620 kPa) maximum air pressure at the inlet with 3/4” (19 mm) inside diameter air supply hose. The sander model 88S45W109 has a free speed of 4,500 rpm and a spindle with a 5/8–11 thread for a 9” back up pad.

Ingersoll-Rand 88S sander is designed for demanding sanding and polishing applications where limited space is an issue. Read the brief product information below for familiarization with the device. For safety, top performance, and maximum durability of the parts, operate the tool at 90 psig (6.2 bar/620 kPa) maximum air pressure at the inlet with 3/4” (19 mm) inside diameter air supply hose. The sander model 88S45W109 has a free speed of 4,500 rpm and a spindle with a 5/8–11 thread for a 9” back up pad.

Refer All Communications to the Nearest
Ingersoll–Rand Office or Distributor.
Ingersoll–Rand Company 1999
Printed in U.S.A.
03529385
Form P6438
Edition 9
April, 1999
OPERATION AND MAINTENANCE MANUAL FOR
88S VERTICAL AIR SANDERS
Series 88S Vertical Air Sanders are designed for heavy duty sanding and polishing
operations where space limitations are a factor.
Ingersoll–Rand is not responsible for customer modification of tools for applications on
which Ingersoll–Rand was not consulted.
IMPORTANT SAFETY INFORMATION ENCLOSED.
READ THIS MANUAL BEFORE OPERATING TOOL.
IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PLACE THE INFORMATION
IN THIS MANUAL INTO THE HANDS OF THE OPERATOR.
FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.
PLACING TOOL IN SERVICE
Always operate, inspect and maintain this tool in
accordance with American National Standards
Institute Safety Code for Portable Air Tools (ANSI
B186.1).
For safety, top performance, and maximum durability
of parts, operate this tool at 90 psig (6.2 bar/620 kPa)
maximum air pressure at the inlet with 3/4” (19 mm)
inside diameter air supply hose.
Always turn off the air supply and disconnect the air
supply hose before installing, removing or adjusting
any accessory on this tool, or before performing any
maintenance on this tool.
Do not use damaged, frayed or deteriorated air hoses
and fittings.
Be sure all hoses and fittings are the correct size and
are tightly secured. See Dwg. TPD905–1 for a typical
piping arrangement.
Always use clean, dry air at 90 psig maximum air
pressure. Dust, corrosive fumes and/or excessive
moisture can ruin the motor of an air tool.
Do not lubricate tools with flammable or volatile
liquids such as kerosene, diesel or jet fuel.
Do not remove any labels. Replace any damaged label.
USING THE TOOL
Always wear eye protection when operating or
performing maintenance on this tool.
Always wear hearing protection when operating this
tool.
Keep hands, loose clothing and long hair away from
rotating end of tool.
Anticipate and be alert for sudden changes in motion
during start up and operation of any power tool.
Keep body stance balanced and firm. Do not
overreach when operating this tool. High reaction
torques can occur at or below the recommended air
pressure.
Check for excessive speed and vibration before
operating.
Tool shaft may continue to rotate briefly after throttle
is released.
Air powered tools can vibrate in use. Vibration,
repetitive motions or uncomfortable positions may be
harmful to your hands and arms. Stop using any tool
if discomfort, tingling feeling or pain occurs. Seek
medical advice before resuming use.
Use accessories recommended by Ingersoll–Rand.
This tool is not designed for working in explosive
atmospheres.
This tool is not insulated against electric shock.
The use of other than genuine Ingersoll–Rand replacement parts may result in safety hazards, decreased tool performance, and
increased maintenance, and may invalidate all warranties.
Repairs should be made only by authorized trained personnel. Consult your nearest Ingersoll–Rand Authorized Servicenter.
F
E
P
2
WARNING LABEL IDENTIFICATION
FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.
Always wear eye protection
when operating or perform-
ing maintenance on this
tool.
WARNING
WARNING
Always wear hearing
protection when operating
this tool.
Always turn off the air sup-
ply and disconnect the air
supply hose before install-
ing, removing or adjusting
any accessory on this tool,
or before performing any
maintenance on this tool.
WARNING
Air powered tools can vibrate
in use. Vibration, repetitive
motions or uncomfortable po-
sitions may be harmful to your
hands and arms. Stop using
any tool if discomfort, tingling
feeling or pain occurs. Seek
medical advice before resum-
ing use.
WARNING
Do not carry the tool by
the hose.
WARNING
WARNING
Do not use damaged, frayed
or deteriorated air hoses
and fittings.
WARNING
Keep body stance balanced
and firm. Do not overreach
when operating this tool.
WARNING
Operate at 90 psig (6.2 bar/
620 kPa) Maximum air pressure.
90 psig
(6.2bar/620kPa)
SANDER SPECIFIC WARNINGS
These Sanders will operate at the free speed specified
on the nameplate if the air supply line furnishes 90
psig (6.2 bar/620 kPa) air pressure at the tool.
Operation at higher air pressure will result in
excessive speed.
Use only a sanding pad, buffing wheel or polishing
bonnet with these tools. Do not use any grinding
wheel, bur or metal removing accessory with these
tools. Never use an accessory having a maximum
operating speed less than the free speed of the Sander
in which it is being used.
When using a pad having a shank, insert the shank to
full depth in the collet. When using a pad on a
threaded arbor, make certain the flange nut is
tightened securely. Check the tightness of the collet
nut or flange nut before operating a Sander to make
certain it will not loosen during operation.
Do not attempt to disassemble the Controller. The
Controller is available only as a unit and is guaranteed
for the life of the tool if it is not abused.
3
PLACING TOOL IN SERVICE
LUBRICATION
Ingersoll–Rand No. 50
Always use an air line lubricator with these tools.
We recommend the following Filter–Lubricator–Regulator
Unit:
For USA – No. C22–04–G00
Before starting the tool, unless the air line lubricator is used,
detach the air hose and inject about 1.5 cc of oil into the air
inlet.
MAIN LINES 3 TIMES
AIR TOOL INLET SIZE
TO
AIR
SYSTEM
TO
AIR
TOOL
LUBRICATOR
REGULATOR
FILTER
BRANCH LINE 2 TIMES
AIR TOOL INLET SIZE
DRAIN REGULARLY
COMPRESSOR
(Dwg. TPD905–1)
HOW TO ORDER A SANDER
VERTICAL DISK WHEEL SANDER
Model Free Speed, rpm Spindle and Back Up Pad
88S45W109 4,500 5/8–11, 9”
88S60W107 6,000 5/8–11, 7”
Adressez toutes vos communications au Bureau
Ingersoll–Rand ou distributeur le plus proche.
Ingersoll–Rand Company 1999
Imprimé aux É.U.
MANUEL D’EXPLOITATION ET D’ENTRETIEN
DE LA SÉRIE 88S
NOTE
Les ponceuses verticales de la Série 88S sont destinées aux grosses opérations de ponçage
et de polissage où l’espace disponible est limité.
Ingersoll–Rand ne peut être tenu responsable de la modification des outils par le client pour
les adapter à des applications qui n’ont pas été approuvées par Ingersoll–Rand.
ATTENTION
D’IMPORTANTES INFORMATIONS DE SECURITÉ SONT JOINTES.
LIRE CE MANUEL AVANT D’UTILISER L’OUTIL.
L’EMPLOYEUR EST TENU DE COMMUNIQUER LES INFORMATIONS
DE CE MANUEL AUX EMPLOYÉS UTILISANT CET OUTIL.
LE NON RESPECT DES AVERTISSEMENTS SUIVANTS PEUT CAUSER DES BLESSURES.
MISE EN SERVICE DE L’OUTIL
Toujours exploiter, inspecter et entretenir cet outil
conformément au Code de sécurité des outils
pneumatiques portatifs de l’American National
Standards Institute (ANSI B186.1).
Pour la sécurité, les performances optimales et la
durabilité maximale des pièces, cet outil doit être
connecté à une alimentation d’air comprimé de
6,2 bar (620 kPa) maximum à l’entrée, avec un flexible
de 19 mm de diamètre intérieur.
Couper toujours l’alimentation d’air comprimé et
débrancher le flexible d’alimentation avant d’installer,
déposer ou ajuster tout accessoire sur cet outil, ou
d’entreprendre une opération d’entretien quelconque
sur l’outil.
Ne pas utiliser des flexibles ou des raccords
endommagés, effilochés ou détériorés.
S’assurer que tous les flexibles et les raccords sont
correctement dimensionnés et bien serrés. Voir Plan
TPD905–1 pour un exemple type d’agencement des
tuyauteries.
Utiliser toujours de l’air sec et propre à une pression
maximum de 6,2 bar. La poussière, les fumées
corrosives et/ou une humidité excessive peuvent
endommager le moteur d’un outil pneumatique.
Ne jamais lubrifier les outils avec des liquides
inflammables ou volatiles tels que le kérosne, le gasol
ou le carburant d’aviation.
Ne retirer aucune étiquette. Remplacer toute étiquette
endommagée.
UTILISATION DE L’OUTIL
Porter toujours des lunettes de protection pendant
l’utilisation et l’entretien de cet outil.
Porter toujours une protection acoustique pendant
l’utilisation de cet outil.
Tenir les mains, les vêtements flous et les cheveux
longs, éloignés de l’extrémité rotative de l’outil.
Prévoir, et ne pas oublier, que tout outil motorisé est
susceptible d’à–coups brusques lors de sa mise en
marche et pendant son utilisation.
Garder une position équilibrée et ferme. Ne pas se
pencher trop en avant pendant l’utilisation de cet
outil. Des couples de réaction élevés peuvent se
produire à, ou en dessous, de la pression d’air
recommandée.
Vérifier que la vitesse et les vibrations ne sont pas
excessives avant d’utiliser l’outil.
La rotation des accessoires de l’outil peut continuer
pendant un certain temps après le relâchement de la
gâchette.
Les outils pneumatiques peuvent vibrer pendant
l’exploitation. Les vibrations, les mouvements
répétitifs et les positions inconfortables peuvent causer
des douleurs dans les mains et les bras. N’utiliser plus
d’outils en cas d’inconfort, de picotements ou de
douleurs. Consulter un médecin avant de
recommencer à à utiliser l’outil.
Utiliser les accessoires recommandés par
Ingersoll–Rand.
Esta herramienta no ha sido diseñada para trabajar
en ambientes explosivos.
Esta herramienta no está aislada contra descargas
eléctricas.
NOTE
L’utilisation de rechanges autres que les pièces d’origine Ingersoll–Rand peut causer des risques d’insécurité, réduire les
performances de l’outil et augmenter l’entretien, et peut annuler toutes les garanties.
Les réparations ne doivent être effectuées que par des réparateurs qualifiés autorisés. Consultez votre Centre de Service
Ingersoll–Rand le plus proche.
F
5
SIGNIFICATION DES ETIQUETTES D’AVERTISSEMENT
ATTENTION
LE NON RESPECT DES AVERTISSEMENTS SUIVANTS PEUT CAUSER DES BLESSURES
Porter toujours des lunettes
de protection pendant
l’utilisation et l’entretien de
cet outil.
ATTENTION ATTENTION
Porter toujours une
protection acoustique
pendant l’utilisation de cet
outil.
Les outils pneumatiques
peuvent vibrer pendant
l’exploitation. Les vibrations,
les mouvements répétitifs et les
positions inconfortables
peuvent causer des douleurs
dans les mains et les bras.
N’utiliser plus d’outils en cas
d’inconfort, de picotements ou
de douleurs. Consulter un
médecin avant de recommencer
à utiliser l’outil.
ATTENTION
Ne pas transporter l’outil
par son flexible.
ATTENTION
ATTENTION
Garder une position équilibrée et
ferme. Ne pas se pencher trop
en avant pendant
l’utilisation de cet outil.
ATTENTION
Utiliser de l’air comprimé
à une pression maximum
de 6,2 bar (620 kPa).
90 psig
(6.2bar/620kPa)
Couper toujours l’alimentation
d’air comprimé et débrancher le
flexible d’alimentation avant
d’installer, déposer ou ajuster
tout accessoire sur cet outil, ou
d’entreprendre une opération
d’entretien quelconque sur l’ou-
til.
ATTENTION
ATTENTION
Ne pas utiliser des flexibles ou
des raccords endommagés,
effilochés ou détériorés.
AVERTISSEMENTS SPÉCIFIQUES AUX PONCEUSES
Ces ponceuses tourneront à la vitesse à vide spécifiée
sur la plaque signalétique lorsque le circuit
d’alimentation fournit de l’air à une pression de 6,2
bar (620 kPa) à l’outil. L’exploitation à une pression
supérieure produira une vitesse excessive.
Utiliser seulement un plateau de ponçage, un disque
de polissage ou une peau de mouton de polissage avec
ces outils. Ne jamais utiliser de meule ou d’accessoire
d’ébavurage ou d’enlèvement de métal sur ces outils.
Ne jamais utiliser d’accessoire ayant une vitesse de
fonctionnement maximum inférieure à la vitesse à vide
de la ponceuse sur laquelle il est utilisé.
Lorsqu’un plateau de ponçage à tige est utilisé, insérer
la tige à fond dans la pince. Lorsqu’un plateau est
utilisé sur un arbre fileté, vérifier que l’écrou de bride
est fermement serré. Vérifier le serrage de l’écrou de
pince ou de l’écrou d’arbre avant de mettre la
ponceuse en marche, et vérifier qu’il ne se desserre
pas pendant l’exploitation.
Ne jamais essayer de démonter le contrôleur. Ce
dernier est fourni seulement comme un ensemble et
est garanti pendant toute la durée de vie de l’outil s’il
est utilisé correctement.
6
MISE EN SERVICE DE L’OUTIL
LUBRIFICATION
Ingersoll–Rand No. 50
Utiliser toujours un lubrificateur avec ces outils. Nous
recommandons l’emploi du filtre–régulateur–lubrificateur
suivant :
For USA – No. C22–04–G00
Avant de mettre l’outil en marche, si un lubrificateur de
ligne n’est pas utilisé, débrancher le flexible d’alimentation et
verser environ 1,5 cm
3
d’huile dans le raccord d’admission de
l’outil.
TUYAUTERIE PRINCIPALE
AU MOINS 3 FOIS LA DIMEN-
SION DE L’ADMISSION D’AIR
DE L’OUTIL
VERS LE
RÉSEAU D’AIR
COMPRIMÉ
VERS
L’OUTIL
PNEU-
MATIQUE
LUBRIFICATEUR
RÉGULATEUR
FILTRE
LIGNE SECONDAIRE AU
MOINS 2 FOIS LA DIMEN-
SION DE L’ADMISSION
D’AIR DE L’OUTIL
VIDANGER
RÉGULIÈREMENT
COMPRESSEUR
(Plan TPD905–1)
SPÉCIFICATIONS
Modèle Vitesse libre Broche et plateau
d’appui
tr/mn
88S45W109 4.500 5/8–11, 9”
88S60W107 6.000 5/8–11, 7”
Toda comunicación se deberá dirigir a la oficina o
al distribuidor Ingersoll–Rand más próximo.
Ingersoll–Rand Company 1999
Impreso en EE. UU.
MANUAL DE FUNCIONAMIENTO Y MANTENIMIENTO
LIJADORAS VERTICALES DE LA SERIE 88S
NOTA
Las lijadoras neúmaticas verticales de la serie 88S están diseñadas para trabajos de lijado y
pulido de alto rendimiento en aquellas situaciones en que el espacio es reducido.
Ingersoll–Rand no aceptará responsabilidad alguna por la modificación de las herramientas
efectuada por el cliente para las aplicaciones que no hayan sido consultadas con
Ingersoll–Rand.
AVISO
SE ADJUNTA INFORMACIÓN IMPORTANTE DE SEGURIDAD.
LEA ESTE MANUAL ANTES DE UTILIZAR LA HERRAMIENTA.
ES RESPONSABILIDAD DE LA EMPRESA ASEGURARSE DE QUE EL OPERARIO ESTÉ AL
TANTO DE LA INFORMACIÓN QUE CONTIENE ESTE MANUAL.
EL HACER CASO OMISO DE LOS AVISOS SIGUIENTES PODRÍA OCASIONAR LESIONES.
PARA PONER LA HERRAMIENTA EN SERVICIO
Utilice, examine y mantenga siempre esta herramienta
conforme al código de seguridad para herramientas
neumáticas portátiles de la American National
Standards Institute (ANSI B186.1).
Para mayor seguridad, rendimiento óptimo y larga
vida útil de las piezas, utilice esta herramienta a una
presión de aire máxima de 90 psig (6,2 bar/620 kPa)
con una manguera de suministro de aire con diámetro
interno de 19 mm.
Corte siempre el suministro de aire y desconecte la
manguera de suministro de aire antes de instalar,
desmontar o ajustar cualquier accesorio de esta
herramienta, o antes de realizar cualquier operación
de mantenimiento de la misma.
No utilice mangueras de aire y racores dañados,
desgastados o deteriorados.
Asegúrese de que todos los racores y mangueras sean
del tamaño correcto y estén bien apretados. El Esq.
TPD905–1 muestra una disposición característica de
las tuberías.
Use siempre aire limpio y seco a una presión máxima
de 90 psig (6,2 bar/620 kPa). El polvo, los gases
corrosivos y/o el exceso de humedad pueden estropear
el motor de una herramienta neumática.
No lubrique las herramientas con líquidos inflamables
o volátiles tales como queroseno, gasoil o combustible
para motores a reacción.
No saque ninguna etiqueta. Sustituya toda etiqueta
dañada.
UTILIZACIÓN DE LA HERRAMIENTA
Lleve siempre protección ocular cuando utilice esta
herramienta o realice operaciones de mantenimiento
en la misma.
Lleve siempre protección para los oídos cuando utilice
esta herramienta.
Mantenga las manos, la ropa suelta y el cabello largo
alejados del extremo giratorio de la herramienta.
Anticipe y esté alerta a los cambios repentinos en el
movimiento durante la puesta en marcha y utilización
de toda herramienta motorizada.
Mantenga una postura del cuerpo equilibrada y firme.
No estire demasiado los brazos al manejar la
herramienta. Pueden darse elevados pares de reacción
a la presión de aire recomendada, e incluso a presiones
inferiores.
Compruebe que no haya exceso de velocidad o
vibración de la herramienta antes de utilizarla.
El eje de la herramienta puede seguir girando
brevemente después de haberse soltado la palanca de
mando.
Las herramientas neumáticas pueden vibrar durante
el uso. La vibración, los movimientos repetitivos o las
posiciones incómodas pueden deñarle los brazos y
manos. En caso de incomodidad, sensación de
hormigueo o dolor, deje de usar la herramienta.
Consulte al médico antes de volver a utilizarla.
Utilice únicamente los accesorios recomendados por
Ingersoll–Rand.
Esta herramienta no ha sido diseñada para trabajar
en ambientes explosivos.
Esta herramienta no está aislada contra descargas
eléctricas.
NOTA
El uso de piezas de recambio que no sean las auténticas piezas Ingersoll–Rand puede poner en peligro la seguridad, reducir el
rendimiento de la herramienta y aumentar los cuidados de mantenimiento necesarios, así como invalidar toda garantía.
Las reparaciones sólo se deben encomendar a personal debidamente cualificado y autorizado. Consulte con el centro de servicio
autorizado Ingersoll–Rand más próximo.
E
8
ETIQUETAS DE AVISO
AVISO
EL HACER CASO OMISO DE LOS AVISOS SIGUIENTES PODRÍA OCASIONAR
LESIONES.
Usar siempre protección ocular
al manejar o realizar opera-
ciones de mantenimiento en
esta herramienta.
ADVERTENCIA
Usar siempre protección
para los oídos al manejar
esta herramienta.
Las herramientas neumáticas
pueden vibrar durante el uso.
La vibración, los movimientos
repetitivos o las posiciones
incómodas podrían dañarle los
brazos y las manos. En caso
de incomodidad, sensación de
hormigueo o dolor, dejar de
usar la herramienta. Consultar
al médico antes de volver a uti-
lizarla.
No coger la herramienta
por la manguera para le-
vantarla.
ADVERTENCIA
Mantener una postura del cuerpo
equilibrada y firme. No estirar de-
masiado los brazos al manejar la
herramienta.
Manejar la herramienta a una
presión de aire máxima de 90
psig (6,2 bar/620 kPa).
90 psig
(6.2bar/620kPa)
Cortar siempre el suministro
de aire y desconectar la man-
guera de suministro de aire
antes de instalar, retirar o ajus-
tar cualquier accesorio de esta
herramienta, o antes de realizar
cualquier operación de man-
tenimiento de la misma.
No utilizar mangueras de aire
y accesorios dañados, des-
gastados ni deteriorados.
ADVERTENCIA
ADVERTENCIA
ADVERTENCIA
ADVERTENCIA
ADVERTENCIA
ADVERTENCIA
AVISOS ESPECÍFICOS SOBRE LAS LIJADORAS
Estas lijadoras funcionan a la velocidad en vacío
que se indica en la placa de identificación si la red
de aire comprimido suministra a la herramienta
aire a una presión de 90 psig (6,2 bar/620 kPa). El
manejo a una presión superior producirá un exceso
de velocidad.
Utilice solamente discos de lijar o de pulir con estas
herramientas. No utilice muelas de rectificar, fresas
ni accesorios de desbarbado de metal con estas
herramientas. No utilice nunca un accesorio cuya
velocidad máxima de funcionamiento sea inferior a
la velocidad en vacío de la lijadora con la que se
emplea.
Al utilizar un disco con eje, introduzca el eje
completamente en la pinza. Cuando utilice un disco
en un eje roscado, asegúrese de que la tuerca de la
brida quede bien apretada. Compruebe el apriete
de la tuerca de la pinza o de la brida antes de
accionar la lijadora para asegurarse de que no se
afloje durante el funcionamiento.
No intente desarmar el estrangulador. Éste está
disponible únicamente como conjunto y está
garantizado para toda la vida útil de la
herramienta, siempre que se utilice como es debido.
9
PARA PONER LA HERRAMIENTA EN SERVICIO
LUBRICACIÓN
Ingersoll–Rand Nº 50
Utilice siempre un lubricador de aire comprimido con estas
herramientas. Recomendamos utilizar el siguiente conjunto de
filtro–lubricador–regulador:
Para EE.UU. – Nº C22–04–G00
Antes de accionar la herramienta, salvo que se utilice un
lubricador de aire comprimido, desconecte la manguera de
aire e inyecte unos 1,5 cc de aceite en el conjunto de
admisión.
TUBERÍAS PRINCIPALES 3
VECES EL TAMAÑO DE
ENTRADA DE HERRAMIENTA
NEUMÁTICA
AL SISTEMA
NEUMÁTICO
A LA
HERRA–
MIENTA
NEUMÁTICA
LUBRICADOR
REGULADOR
FILTRO
TUBERÍA DE RAMAL
2 VECES EL TAMAÑO
DE ENTRADA DE
HERRAMIENTA
NEUMÁTICA
PURGAR
PERIÓDICAMENTE
COMPRESOR
(Esq. TPD905–1)
ESPECIFICACIONES
Modelo Velocidad en vacío Husillo y disco
soporte
rpm
88S45W109 4.500 5/8–11, 9”
88S60W107 6.000 5/8–11, 7”
Envie toda a correspondência ao Escritório
ou Distribuidor Ingersoll–Rand mais próximo.
Ingersoll–Rand Company 1999
Impresso nos E.U.A.
MANUAL DE FUNCIONAMENTO E MANUTENÇÃO
LIXADEIRAS PNEUMÁTICAS VERTICAIS SÉRIE 88S
AVISO
As Lixadeiras Pneumáticas Verticais Série 88S são concebidas para operações pesadas de
lixar e polir, onde as limitações de espaço são um factor relevante.
A Ingersoll–Rand não pode ser responsabilizada pela modificação de ferramentas para
aplicações para as quais não tenha sido consultada.
ADVERTÊNCIA
IMPORTANTES INFORMAÇÕES DE SEGURANÇA EM ANEXO.
LEIA ESTE MANUAL ANTES DE OPERAR A FERRAMENTA.
É RESPONSABILIDADE DA ENTIDADE PATRONAL PÔR AS INFORMAÇÕES
CONTIDAS NESTE MANUAL À DISPOSIÇÃO DOS UTILIZADORES.
A NÃO OBEDIÊNCIA ÀS ADVERTÊNCIAS SEGUINTES PODERÁ RESULTAR EM LESÕES PESSOAIS.
COLOCAÇÃO DA FERRAMENTA EM SERVIÇO
Sempre opere, inspeccione e mantenha esta
ferramenta de acordo com o Código de Segurança do
Instituto Americano de Padrões Nacionais para
Ferramentas Pneumáticas Portáteis (ANSI B186.1).
Para segurança, desempenho superior e durabilidade
máxima das peças, opere esta ferramenta a uma
pressão de ar máxima de 90 psig (6,2 bar/620 kPa) na
admissão com uma mangueira de alimentação de ar
com diâmetro interno de 3/4 pol. (19 mm).
Desligue sempre a alimentação de ar e a mangueira de
alimentação de ar antes de instalar, retirar ou ajustar
qualquer acessório desta ferramenta, ou antes de fazer
manutenção na mesma.
Não utilize mangueiras de ar e acessórios danificados,
puídos ou deteriorados.
Certifique–se de que todas as mangueiras e acessórios
são da dimensão correcta e que estão seguros
firmemente. Consulte o Des. TPD905–1 para uma
disposição de tubos típica.
Utilize sempre ar limpo e seco a uma pressão máxima
de 90 psig. Poeira, fumos corrosivos e/ou humidade
excessiva podem destruir o motor de uma ferramenta
pneumática.
Não lubrifique a ferramenta com líquidos inflamáveis
ou voláteis como querosene, gasóleo ou combustível
para jactos.
Não retire nenhum rótulo. Substitua os rótulos
danificados.
UTILIZAÇÃO DA FERRAMENTA
Use sempre protecção para os olhos ao operar ou fazer
manutenção nesta ferramenta.
Use sempre protecção auricular ao operar esta
ferramenta.
Mantenha as mãos, roupas soltas e cabelos longos
afastados da extremidade rotativa da ferramenta.
Esteja preparado e alerta para mudanças súbitas no
movimento durante o arranque e o funcionamento de
qualquer ferramenta mecânica.
Mantenha o corpo numa posição equilibrada e firme.
Não estique o corpo ao operar esta ferramenta. Podem
ocorrer binários de reacção elevados à ou abaixo da
pressão do ar recomendada.
Verifique a ferramenta quanto a velocidade ou
vibração excessiva antes de a operar.
O veio da ferramenta pode continuar a rodar por um
curto período de tempo depois de soltar o regulador.
A ferramentas pneumáticas podem vibrar durante a
utilização. Vibração, movimentos repetitivos ou
posições desconfortáveis podem ser nocivos às suas
mãos e braços. Pare de utilizar qualquer ferramenta
se ocorrer desconforto, sensação de formigueiro ou
dor. Procure assistência médica antes de reiniciar a
utilização.
Use os acessórios recomendados pela Ingersoll–Rand.
Esta ferramenta não é concebida para funcionar em
atmosferas explosivas.
Esta ferramenta não é isolada contra choque eléctrico.
AVISO
A utilização de qualquer peça sobresselente que não seja Ingersoll–Rand genuína pode resultar em riscos para a segurança, em
desempenho reduzido da ferramenta e mais necessidade de manutenção, e pode invalidar todas as garantias.
As reparações só devem ser feitas por pessoal autorizado e com formação adequada. Consulte o Representante Autorizado
Ingersoll–Rand mais próximo.
P
11
IDENTIFICAÇÃO DAS ETIQUETAS DE ADVERTÊNCIA
ADVERTÊNCIA
A NÃO OBEDIÊNCIA ÀS ADVERTÊNCIAS SEGUINTES PODERÁ RESULTAR EM LESÕES PESSOAIS.
Use sempre protecção para os
olhos ao operar ou fazer
manutenção nesta ferramenta.
Use sempre protecção
auricular ao operar esta
ferramenta.
Desligue sempre a alimentação
de ar e a mangueira de
alimentação de ar antes de
instalar, remover ou ajustar um
acessório desta ferramenta, ou
antes de fazer manutenção na
mesma.
As ferramentas pneumáticas
podem vibrar durante a utilização.
Vibração, movimentos repetitivos
ou posições desconfortáveis
podem ser nocivos às suas mãos e
braços. Pare de utilizar qualquer
ferramenta se ocorrer desconforto,
sensação de formigueiro ou dor.
Procure assistência médica antes
de reiniciar a utilização.
Não transporte a ferramenta
pela mangueira.
ADVERTÊNCIA
Não utilize mangueiras de
ar e acessórios danificados,
puídos ou deteriorados.
Mantenha o corpo numa
posição equilibrada e firme.
Não estique o corpo ao
operar esta ferramenta.
Opere a uma pressão de ar
máxima de 90 psig (6,2 bar/
620 kPa).
90 psig
(6.2bar/620kPa)
ADVERTÊNCIA
ADVERTÊNCIA
ADVERTÊNCIA
ADVERTÊNCIA
ADVERTÊNCIA
ADVERTÊNCIA
ADVERTÊNCIA
ADVERTÊNCIAS ESPECIAIS PARA A LIXADEIRA
Estas Lixadeiras funcionarão à velocidade livre
especificada na placa de identificação se a linha de ar
fornecer pressão de ar a 90 psig (6,2 bar/620 kPa) na
ferramenta. A operação a uma pressão mais elevada
resultará em velocidade excessiva.
Utilize apenas uma almofada de lixar, roda de polir ou
boina de polir com estas ferramentas. Não utilize mó
abrasiva, rebarbador ou acessório para remoção de
metal com estas ferramentas. Nunca utilize um
acessório que tenha uma velocidade máxima de
funcionamento abaixo da velocidade livre da
Lixadeira na qual o acessório está a ser utilizado.
Ao utilizar uma almofada que tenha um veio,
introduza–o totalmente no mandril. Ao utilizar uma
almofada num veio roscado, certifique–se de que a
porca de flange está apertada firmemente. Verifique o
aperto da porca do mandril ou da porca de flange
antes de operar a Lixadeira para assegurar que a
porca não desapertará durante o funcionamento.
Não tente desmontar o Controlador. O Controlador
está disponível como uma unidade e é garantido
durante a vida útil da ferramenta, se não for
maltratado.
12
COLOCAÇÃO DA FERRAMENTA EM SERVIÇO
LUBRIFICAÇÃO
Ingersoll–Rand Nº 50
Utilize sempre um lubrificador de linha de ar com estas
ferramentas.
Recomendamos a seguinte Unidade Filtro–Lubrificador–
Regulador:
For USA – No. C22–04–G00
Antes de ligar a ferramenta, a menos que o lubrificador de
linha de ar esteja a ser utilizado, desligue a mangueira de ar e
injecte aproximadamente 1,5 cc de óleo na admissão de ar.
LINHAS PRINCIPAIS – 3 VEZES
A DIMENSÃO DA ADMISSÃO DA
FERRAMENTA PNEUMÁTICA
PARA O
SISTEMA
DE AR
PARA A
FERRAMENTA
PNEUMÁTICA
LUBRIFICADOR
REGULADOR
FILTRO
LINHA SECUNDÁRIA –
2 VEZES A DIMENSÃO
DA ADMISSÃO DA
FERRAMENTA
PNEUMÁTICA
DRENAR
REGULARMENTE
COMPRESSOR
(Des. TPD905–1)
ESPECIFICAÇÕES
Modelo Velocidade Livre Haste e Almofada
de Apoio
rpm mm (pol.)
88S45W109 4.500 5/8–11, 9”
88S60W107 6.000 5/8–11, 7”
MAINTENANCE SECTION
13
(TPA719–6)
MAINTENANCE SECTION
14
PART NUMBER FOR ORDERING PART NUMBER FOR ORDERING
+ 1 Cylinder Case Assembly * Nameplate . . . . . . . . . . . . . . . . . . . . . . . . . . . 88S60–301
for all models ending in –EU . . . . . 88V60–EU–A25 * Nameplate Screw (4) . . . . . . . . . . . . . . . . . . . BN403–302
for all other models . . . . . . . . . . . . . 88V60–A25 25 Dead Handle . . . . . . . . . . . . . . . . . . . . . . . . . ERG0–A48
2 Throttle Valve Assembly . . . . . . . . . . . . . 88V60–A302 27 Arbor
♦• 3 Seal (2) . . . . . . . . . . . . . . . . . . . . . . . . . C321–606 for 88S45 (4500 rpm) (brown) . . . 88S45–204–W10
4 Inlet Bushing . . . . . . . . . . . . . . . . . . . . . . 88V60–38 for 88S60 (6000 rpm) (blue) . . . . . 88S60–204–W10
♦• 5 Inlet Bushing Screen . . . . . . . . . . . . . . . . 834–61 28 Front Rotor Bearing . . . . . . . . . . . . . . . . . . . . R380–105
♦• 6 Throttle Valve Spring . . . . . . . . . . . . . . . . 99V60–262 29 Front End Plate . . . . . . . . . . . . . . . . . . . . . . . 88V60–11
7 Throttle Valve Seat Support Assembly . . 88V60–A303 30 Rotor Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88V60–70
♦• 8 Air Strainer Screen . . . . . . . . . . . . . . . 834–61 31 Rotor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88V60–53
♦• 9 Valve Seat . . . . . . . . . . . . . . . . . . . . . . R4–159A ♦• 32 Vane Packet (set of 4 Vanes) . . . . . . . . . . . . . 88V60–42–4
10 Valve Seat Washer . . . . . . . . . . . . . . . . 99V60–155 33 Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88V60–3
11 Valve Screw Lock Washer . . . . . . . . . . H54U–352 34 Cylinder Dowel . . . . . . . . . . . . . . . . . . . . . . . 88V60–98
12 Valve Seat Screw . . . . . . . . . . . . . . . . . PS3–83 35 Rear End Plate . . . . . . . . . . . . . . . . . . . . . . . . 88V60–12
13 Throttle Lever Pin . . . . . . . . . . . . . . . . . . MR–100 ♦• 36 Rear End Plate Gasket . . . . . . . . . . . . . . . . . . 88V60–739
14 Locking Lever Assembly . . . . . . . . . . . . . 88V60–A400 37 Controller Assembly
15 Lever Lock . . . . . . . . . . . . . . . . . . . . . . 88V60–402 for 88S45 (4500 rpm) (brown) . . . 88S45–A424
16 Lever Lock Spring . . . . . . . . . . . . . . . . 88V60–405 for 88S60 (6000 rpm) (blue) . . . . . 88V60–A424
17 Lever Lock Pin . . . . . . . . . . . . . . . . . . 502B–120 38 Rotor Bearing Seal Assembly . . . . . . . . . 88V60–A28
* Nameplate (for 88V60–EU–A25) . . . . . . 88V–EU–K301 40 Controller Retaining Ring . . . . . . . . . . . . . . . 88V60–118
* Nameplate Screw (for 88V60–EU–A25) (4) BN403–302 41 Motor Clamp Belleville Washer (2) . . . . . . . 88V60–207
* Warning Label (for 88V60–EU–A25) . . . EU–99 ♦• 42 Cylinder Case Gasket . . . . . . . . . . . . . . . . . . 88V60–283
* Nameplate Kit (for 88V60–A25) . . . . . . . 88V–K301 43 Motor Retaining Plate . . . . . . . . . . . . . . . . . . 88S60–55
Nameplate Screw (4) . . . . . . . . . . . . . . BN403–302 44 Cylinder Case Screw Lock Washer (5) . . . . . 10BM–67
Warning Label . . . . . . . . . . . . . . . . . . . WARNING–5–99 45 Cylinder Case Screw (5) . . . . . . . . . . . . . . . . 99V60–638
20 Exhaust Deflector . . . . . . . . . . . . . . . . . . . . . 99V60–23
21 Exhaust Deflector Screw (3) . . . . . . . . . . . . . 99V60–200
* Not illustrated.
Indicates Tune–up Kit part.
To keep downtime to a minimum, it is desirable to have on hand certain repair parts. We recommend that you stock one (pair or set) of each part indicated by a
bullet () for every four tools in service.
+ Whenever a new Cylinder Case Assembly is installed, select the correct Nameplate from the Nameplate Kit and attach it to the Cylinder Case with the Nameplate
Screws.
MAINTENANCE SECTION
15
PART NUMBER FOR ORDERING PART NUMBER FOR ORDERING
46 Sanding Pad Assembly 48 Wrench . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AG230–26M
with 5” Sanding Pad . . . . . . . . . . . . . . . . 77A–AM825–5 49 Wrench (double end 5/8” x 3/4” . . . . . . . . . . . . . . . DG120–69
with 7” Sanding Pad (medium) . . . . . . . . 77A–AM825–7 * Controller Wrench (for removing or installing
with 7” Sanding Pad (firm) . . . . . . . . . . . 77A–BM825–7 the Controller Assembly) . . . . . . . . . . . . . . . . . . . . . 88V60–950
with 9” Sanding Pad . . . . . . . . . . . . . . . . 77A–AM825–9 * Seal Pressing Tool (for pressing off the Controller
47 Pad Mounting Kit . . . . . . . . . . . . . . . . . . . . . . . . 77A–826 Assembly from the Rear Rotor Bearing) . . . . . . . . . 99V60–951
* Piped–Away Exhaust Kit . . . . . . . . . . . . . . . . . . . . . . 88V60–K184 * Bearing Clamp (for clamping the outer race of
* Exhaust Hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99V60–184 Rear Rotor Bearing to release the Controller) . . . . 99V60–A952
* Exhaust Hose Clamp . . . . . . . . . . . . . . . . . . . . . . DG30–67 * Controller Maintenance Kit (includes
* Exhaust Elbow . . . . . . . . . . . . . . . . . . . . . . . . . . . 88V60–167 88V60–950, 99V60–951 and 99V60–A952) . . . . . . 88V60–K950
* Exhaust Elbow Gasket . . . . . . . . . . . . . . . . . . . . . 99V60–49 * Tune–up Kit (includes illustrated parts 3 [2],
* Exhaust Elbow Screw (3) . . . . . . . . . . . . . . . . . . FEA100–112 5, 6, 8, 9, 32, 36, 40 and 42) . . . . . . . . . . . . . . . . . . 88V/88H–TK3
* Exhaust Hose Band Assembly . . . . . . . . . . . . . . . 99V60–A927
* Exhaust Hose Band (4) . . . . . . . . . . . . . . . . . 99V60–927
* Exhaust Hose Band Screw (4) . . . . . . . . . . . . MT1–36–7/8
* Screw (2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . JC3350–103
* Exhaust Hose Band Nut (6) . . . . . . . . . . . . . . G8–120A
* Not illustrated.
16
MAINTENANCE SECTION
Always wear eye protection when operating or
performing maintenance on this tool.
Always turn off air supply and disconnect air supply
hose before installing, removing or adjusting any
accessory on this tool, or before performing any
maintenance on this tool.
LUBRICATION
Whenever a Series 88S Sander is disassembled for overhaul
or replacement of parts, lubricate as follows:
1. Inject about 1.5 cc of Ingersoll–Rand No. 50 Oil into
the Inlet Bushing (4) after assembly.
2. If the Sander is used in an extremely dirty
environment, once each week or after each forty
hours of operation, pour a liberal amount of a suitable
cleaning solution into the slots in the handle. Work the
throttle lever vigorously to wash the cleaning solution
around, then pour the solution and accumulated dirt
from the handle. Repeat this process until the cleaning
solution is clean when it comes out of the handle.
Immediately after flushing with the cleaning solution,
inject a liberal amount of Ingersoll–Rand No. 50 Oil in
the slots and, again, work the throttle lever vigorously
to lubricate the cleaned parts.
DISASSEMBLY
General Instructions
1. Do not disassemble the tool any further than necessary
to replace or repair damaged parts.
2. Whenever grasping a tool or part in a vise, always use
leather–covered or copper–covered vise jaws to protect
the surface of the part and help prevent distortion.
This is particularly true of threaded members and
housings.
3. Do not remove any part which is a press fit in or on a
subassembly unless the removal of that part is
necessary for repairs or replacement.
4. Do not disassemble the Sander unless you have a
complete set of new gaskets and O–rings for
replacement.
Disassembly of the Motor and Throttle
1. Grasp the flats of the live air handle in leather–covered
or copper–covered vise jaws with the Spindle upward.
2. Remove the Cylinder Case Screws (45), the Lock
Washers (44), the Motor Retaining Plate (43), Cylinder
Case Gasket (42) and the two Motor Clamp Washers
(41).
3. Remove the Sander from the vise.
4. Grasp the Arbor (27) in leather–covered or copper–
covered vise jaws. Lift off the Cylinder Case to expose
the motor.
Use only the special No. 88V60–950 Controller
Wrench for removing the Controller Assembly (39).
Do not attempt to disassemble the Controller. It is
available only as a unit and is guaranteed for the
life of the tool if it is not abused.
5. Remove the Controller Retaining Ring (40) and
unscrew the Controller Assembly which has a
left–hand thread that requires a clockwise rotation
for removal.
6. Lift off the Rotor Bearing Seal (37) and the Rear End
Plate (35).
7. Lift off the Cylinder (33).
8. Remove the Vanes (32).
9. Withdraw the Rotor (31) and lift out the Rotor
Key (30).
10. Remove the arbor and end plate assembly from the
vise. Grasp the Front End Plate (29) in one hand and
tap the small diameter end of the Arbor (27) with a
soft hammer to remove the End Plate.
17
MAINTENANCE SECTION
11. If the Front Rotor Bearing (28) is to be replaced, press
it from the Arbor.
12. Insert the Controller into the No. 99V60–A952
Bearing Clamp and tighten the nut on the fixture.
Insert the No. 99V60–951 Seal Pressing Tool in the
center and press off the Controller. Release the clamp.
13. Place the Cylinder Case in leather–covered or
copper–covered vise jaws to remove the Inlet
Bushing (4), Inlet Bushing Screen (5) and the Throttle
Valve Spring (6). The Bushing has an interference
thread and is tightly fit.
14. Drive out the Throttle Lever Pin (13) to release the
Lever Assembly (14).
15. Using a 3/32” hex wrench, reach inside the handle and
remove the Valve Seat Screw (12) from the Throttle
Valve Seat Support Assembly (7).
16. Thread a No. 8–32 screw about 5” (127 mm) long
into the throttle valve seat support in place of the
removed valve seat screw. A piece of 5/32” welding
rod can be threaded on one end to serve the same
purpose.
17. Grasp the protruding end of the screw in a vise, and
while tapping lightly on the housing or handle with a
plastic hammer, pull on the housing or handle to
withdraw the throttle parts.
18. The Air Strainer Screen (8) can now be removed and
cleaned.
ASSEMBLY
General Instructions
1. Always press on the inner ring of a ball–type bearing
when installing the bearing on a shaft.
2. Always press on the outer ring of a ball–type bearing
when pressing the bearing into a bearing recess.
3. Whenever grasping a tool or part in a vise, always use
leather–covered or copper–covered vise jaws. Take
extra care not to damage threads or distort housings.
4. Always clean every part and wipe every part with a
thin film of oil before installation.
5. Apply a film of O–ring lubricant to all O–rings before
final assembly.
6. Check every bearing for roughness. If an open bearing
must be cleaned, wash it thoroughly in a clean,
suitable, cleaning solution and dry with a clean cloth.
Sealed or shielded bearing should never be cleaned.
Work grease thoroughly into every open bearing before
installation.
Assembly of the Throttle and Inlet
1. Assemble the Valve Seat Support parts (7, 8, 9, 10, 11
and 12). Tighten the Valve Seat Screw to 12 in–lb
(1.4 Nm) torque.
2. Insert the assembly into the handle, large diameter
first. Position a punch against the flat of the screw
head and tap it with a hammer until the assembly is
firmly seated.
3. Apply O–ring lubricant to the Seals (3). Fit the seals to
the Throttle Valve (2) and push the assembly, small
diameter first, into the handle until it seats firmly.
4. Assemble the Locking Lever Assembly (14) as
illustrated below:
Locking Lever Assembly
(Dwg. TPD563)
5. Align the holes in the Lever Assembly with the
slots in the Cylinder Case. With a soft face hammer,
tap the Throttle Lever Pin (13) through the Lever
Assembly. File off any sharp edges. Operate the
mechanism internally by hand to assure operation.
6. Insert the Throttle Valve Spring (6) small end first.
7. Clean the face of the Inlet Bushing and the Inlet
Bushing Screen (5) with a suitable cleaning solution
and allow to air dry. Insert the parts into the live air
handle. Grasping the flats of the Cylinder Case with a
wrench, tighten to 35 to 45 ft–lb (47 to 61 Nm) torque.
Assembly of the Motor
1. Using an arbor press against the inner race of the
bearing, install the Front Rotor Bearing (28) onto the
Arbor (27).
2. Inspect the Front End Plate (29) for nicks or burrs. If
replacement is necessary, wipe the part with oil. Press
the Front Rotor Bearing into the Front End Plate.
18
MAINTENANCE SECTION
3. Hold the Arbor in leather–covered or copper–covered
vise jaws. Insert the Rotor Key (30) into the slot of the
Rotor (31). The Rotor has a staked keyway on one end.
Place that end up, over the Arbor. Apply a light film of
the recommended oil to each Vane (32) and insert one
Vane, straight edge out, into each slot in the Rotor. If
any new Vanes are required, replace the entire set.
4. Place the Cylinder over the Rotor aligning the
Cylinder Dowel hole with the alignment hole in the
Front End Plate (29), and with the kidney port to the
right of the dowel hole.
5. Apply the Rear End Plate (35) with the kidney port to
the right of the dowel hole.
Take all measurements 30 degrees to the left of the
dowel hole when facing the hub side of the Seal.
Install the Rotor Bearing Seal hub down.
If the Controller Assembly (37) needs to be
replaced, you must also replace the Rotor Bearing
Seal Assembly (38) which consists of a rear rotor
bearing and a rotor bearing seal. If either the rear
rotor bearing or rotor bearing seal needs to be
replaced, BOTH must be replaced with a new
bearing and seal. DO NOT MIX OLD AND NEW
PARTS.
6. Check the outside diameter and large inside diameter
of the Rotor Bearing Seal (38) for wear. If the outside
diameter is worn to 1.176” (29.88 mm) or smaller,
and/or the large inside diameter is worn to 0.910”
(23.12 mm) or larger, install a new Rotor Bearing Seal.
7. Align the Rear End Plate (35), cavity and pin up, with
the larger hole in the Rotor Bearing Seal.
8. Press the Rear Rotor Bearing Seal Assembly onto the
hub of the Controller.
Use only the special 88V60–950 Controller Wrench
for installing the Controller Assembly.
Tighten the Controller between 14 and 16 ft–lb
(19.0 and 21.7 Nm) torque. Do not exceed 16 ft–lb.
The Controller may be damaged if this
torque is exceeded. Always check the free speed of a
Sander after it has been reassembled and before it
is put back into service. Refer to the Test and
Inspection Procedure.
Never use a Sander which runs in excess of the
maximum speed listed in the Test and Inspection
Procedure.
9. Thread the Controller Assembly onto the end of the
Arbor. Rotate the Controller clockwise since this is a
left–hand thread.
10. Install the Controller Retaining Ring (40) onto the
Arbor with the concave face closest to the Controller.
11. Place the live air handle in leather–covered or
copper–covered vise jaws, Cylinder Case Assembly
up. Lightly dampen the Rear End Plate Gasket (36)
with oil. Line the hole in the Gasket with the hole in
the Cylinder Case, and align the notch in the Gasket
with the notch in the motor seat.
12. With an assembly dowel, line up the motor in the
Cylinder Case. Remove the assembly dowel and insert
the Cylinder Dowel (34).
13. Install the two Motor Clamp Washers (41) concave or
dish side up.
14. Apply the Cylinder Case Gasket (42), the Motor
Retaining Plate (43), the Cylinder Case Screw Lock
Washers (45) and the five Screws (46). Slightly tighten
opposite screws, make sure the arbor is free, and
tighten all screws to 14 ft–lb (19 Nm) torque.
15. Rotate the Arbor manually to make certain it is free.
16. The Dead Handle (25) may be adjusted to two
positions. Insert a 5” (127 mm) long 3/16” hex wrench
into the elongated slot in the end of the Dead Handle
and loosen the screw securing the Handle to the
Cylinder Case. Rotate the Handle 180° and tighten the
screw to 18 ft–lb (24.4 Nm) torque.
17. Install the Exhaust Deflector (20) and Screws (21).
19
MAINTENANCE SECTION
TEST AND INSPECTION PROCEDURE
Disconnect the sander from the air supply hose or shut
off air to the tool and bleed the air from the line before
proceeding with the Test and Inspection Procedure.
Run the performance tests at 90 psig (6.2 bar/620 kPa) air
pressure at the inlet of the tool with an eight foot length of
3/4” (19 mm) diameter air supply hose.
1. Without a sanding pad on the tool, operate the Sander
with the Throttle Lever fully actuated and check the
free speed by applying a hand–held tachometer to the
spindle end. Record the Sander serial number, date of
test and actual free speed in a permanent file. The
minimum and maximum allowable free speeds are as
follows:
Free Speed, rpm
Model Stamped Min. Max.
88S45 4500 4300 4550
88S60 6000 5650 6050
2. Attach the power test adapter to the spindle and test
the 88S45 using a 4F Test Fan and test the 88S60 using
an R3 Fan. The minimum allowable speed for 88S45 is
3 000 rpm; for 88S60, it is 4 700 rpm.
3. There must be no objectionable leaks in any non–
exhaust area. The Throttle must not leak when it is
closed.
4. There must be no leaks past the closed Throttle that
will run the motor.
5. The Sander must start smoothly when the Throttle
Lever is actuated and must shut off completely when
the Throttle Lever is released.
6. The Sander must be equipped with a spring–loaded
window style Lock (15). The Lock must return to the
locked position when the Throttle Lever is released
and must prevent operation of the Throttle.
7. The tool must run smoothly without noticeable
vibration or unusual sound.
8. The Arbor (27) must turn freely with no evidence of
brinnelled bearings.
9. The threads on the Arbor must be free of nicks and
damage.
10. The Nameplate must be legible, in place and securely
fastened. Make replacement if necessary.
MAINTENANCE SECTION
TROUBLESHOOTING GUIDE
Trouble
Probable Cause Solution
Low power or low free speed Low air pressure at the Inlet Check the air pressure at the Inlet. The pressure
must not exceed 90 psig (6.2 bar/620 kPa).
Plugged Inlet Bushing Screen Clean the Screen in a clean, suitable, cleaning
solution. If it cannot be cleaned, replace it.
Never operate a Sander without an Inlet Screen.
Ingestion of dirt into the Sander can, in some
cases, cause an unsafe condition.
Worn or broken Vanes Replace a complete set of Vanes.
Worn or broken Cylinder Replace the Cylinder if it is worn or broken or if the
bore is scored or wavy.
Improper lubrication or dirt
build–up in the motor
Lubricate the Sander as instructed in
LUBRICATION SPECIFICATION. If
lubrication does not result in satisfactory operation,
disassemble the motor and inspect and clean all
parts.
Rough operation Worn or broken Rear Rotor
Bearing or Front Rotor Bearing
Examine each Bearing. Replace the Rear Rotor
Bearing Seal Assembly if worn or damaged or
replace the Front Rotor Bearing.
Worn Rotor Key Replace the Key. Check the Arbor and Rotor for key
slot wear and replace if necessary.
Bent Arbor Mount the Arbor on centers. Check the bearing
diameter runout with an indicator. Replace the
Arbor if runout exceeds 0.002” Total Indicator
Reading.
Scoring Improper assembly Make certain that all motor parts are properly
aligned prior to clamping the motor assembly.
Rotor Bearing Seal misalignment Losen the Cylinder Case Screws. Rotate the Spindle
by hand to align the Seal. Retighten the Screws to
14 ft–lb (19 Nm) torque. The Spindle must rotate
freely.
Air leaks Worn Valve Seat or Valve Seat
Washer
Replace worn parts.
Worn Throttle Valve Seals Replace both Seals.
SAVE THESE INSTRUCTIONS. DO NOT DESTROY.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Ingersoll-Rand 88S Operation and Maintenance Manual

Type
Operation and Maintenance Manual
This manual is also suitable for

Ingersoll-Rand 88S sander is designed for demanding sanding and polishing applications where limited space is an issue. Read the brief product information below for familiarization with the device. For safety, top performance, and maximum durability of the parts, operate the tool at 90 psig (6.2 bar/620 kPa) maximum air pressure at the inlet with 3/4” (19 mm) inside diameter air supply hose. The sander model 88S45W109 has a free speed of 4,500 rpm and a spindle with a 5/8–11 thread for a 9” back up pad.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages