Premier LPWS200 Installation guide

Brand: Premier

Model: LPWS200

Category: Mounting kits

Type: Installation guide

Premier LPWS200

The Premier LPWS200 is a versatile and stylish shelving system that offers a range of features to enhance your home or office space. With its sturdy construction and sleek design, the LPWS200 is perfect for displaying books, décor, or other items.

Features:

Adjustable glass shelves allow you to customize the height of the shelves to fit your needs.
Cable management system keeps cords organized and out of sight.
End caps provide a finished look and protect the mounting column from dust.
Easy to install with included hardware and step-by-step instructions.

Possible Use Cases:

Premier LPWS200

Features:

Adjustable glass shelves allow you to customize the height of the shelves to fit your needs.
Cable management system keeps cords organized and out of sight.
End caps provide a finished look and protect the mounting column from dust.
Easy to install with included hardware and step-by-step instructions.

Possible Use Cases:

LPWS100/LPWS200

Installation Instructions Page 1

9533-100-001-00

Step 1. Determine where the shelf will

be installed on the wall.

Step 2. Use a stud ﬁ nder to locate the wall stud.

Step 3. Use a pencil to mark where the

stud is located.

Wood Stud Installation

LPWS100/LPWS200 Shelf Installation Instructions

Installation Tools (not supplied)

Screwdriver

1/8” Drill Bit

Electronic

Stud Finder

Drill

LevelHammer

Pencil

1/4” Drill Bit

Mounting Column

Glass Shelf Wall Anchors

Wood Screws

Flat Head

Screws (Qty 2)

Phillips Head Screw (Qty2)

Flat Washers (Qty 2)

M3 Allen Wrench

Step 4. Place the mounting column over the

located wall stud.

Step 5. Level the mounting column.

Step 6. Use a pencil to mark the mounting

locations (two marks for the LPWS100

and four marks for the LPWS200

mounting locations).

Step 7. Use a 1/8” drill bit and drill to

pre-drill the mounting holes at the

marked locations.

Step 8. Place the mounting column against

the wall and align the mounting points

on the shelf mount with the pre-drilled

mounting holes.

Step 9. Insert and tighten the screws and

re-level the mounting column to

verify the position.

Stud Finder

Mounting

Column

Mounting

Location Mark

Drill

Step 6. Place the mounting column against

the wall and align the mounting points

on the shelf mount with the wall

anchor holes.

Step 7. Level the mounting column.

Step 8. Insert and tighten the screws and

re-level the mounting column to

verify the position.

Mounting

Column

Mounting

Location Mark

Drill

Step 5. Once the mounting holes have been

drilled, insert the wall anchors by

gently pressing the wall anchors into

place.

Level

Mounting

Column

Mounting

Location Mark

Step 1. Determine where the shelf mount will

be installed on the wall.

Step 2. Place the mounting column ﬂ at

against the wall. Make sure the

mounting column is level.

Step 3. Use a pencil to mark the holes where

the mounting column will be located.

Solid Surface Installation

Shelf Mounting Bracket

Glass Shelf

Cap Screw (Qty 1)

Column End Caps

(Qty 2)

Inserting Wall

Anchor

Gently Press

into Place

Wall Anchor

LPWS100

LPWS200

LPWS100 -

(Qty 1)

LPWS200 -

(Qty 2)

LPWS100 -

(Qty 1)

LPWS200 -

(Qty 2)

LPWS100 -

(Qty 2)

LPWS200 -

(Qty 4)

LPWS100 -

(Qty 2)

LPWS200 -

(Qty 4)

Level

Mounting

Column

Mounting

Location Mark

Neck Knuckle (Qty 1)

Step 4. Use a 1/4” drill bit and drill to

pre-drill the mounting holes.

Wall Anchor

Page 2 Installation Instructions

LPWS100/LPWS200

Neck Knuckle Assembly

Shelf Installation

Step 1. Align the neck knuckle on the glass

shelf with the slide channel on the

mounting column.

Step 2. Once aligned, slide the glass shelf

down (doing so while holding the

glass shelf at a 45° angle).

Step 3. When the desired height setting has

been achieved, slowly let the glass

shelf rest forward to a level position

and “click” into place.

Step 4. Use an M3 Allen wrench (supplied)

to tighten the locking screw. Do not

over-tighten this screw.

Locking Screw

Slide

Channel

Neck

Knuckle

Glass

Shelf

M3 Allen

Wrench

Shelf Installation

Cable Management

Step 1. Place the end caps over the upper and

lower ends of the mounting column

and press these end caps ﬁ rmly into

place.

Mounting

Column

End

Cap

Mounting

Points

Shelf Mounting

Bracket

Step 1. Place the glass shelf on a soft, ﬂ at surface

(reﬂ ective-side down).

Step 2. Place the shelf mounting bracket on the

three mounting points (see above).

Threaded Stud

Glass Shelf

Cap Screw

Step 4. Turn the glass shelf over (reﬂ ective-side

up).

In the center of the mounting point there is a

threaded shaft. In order to attach the glass

shelf cap screw, the threaded shaft must

be inthe exact center position of the

mounting point.

Glass Shelf

(Reﬂ ective-side up)

Glass Shelf

(Reﬂ ective-side down)

Step 5. Slowly turn and tighten the glass shelf

cap screw onto the threaded shaft. Do not

over-tighten the glass shelf cap screw.

Step 1. Align the cables on either side of

the mounting column.

Mounting

Column

Cables

Plastic

Tabs

Cables

Shelf Assembly

Step 1. Place the mounting shelf bracket and the

neck knuckle together and align the

mounting holes to the mounting points.

Step 3. Using a screwdriver, insert and tighten

two (2) screws and two (2) ﬂ at washers

(supplied). Do not over-tighten these

screws.

Step 2. Insert and tighten two (2) Phillips ﬂ at

head screws.

Screwdriver

Screw and

Flat Washer

Step 2. Once the cables have been

aligned, gently tuck the cables

into the mounting column.

The plastic tabs will hold the cables

in place once they have been tucked

completely into the mounting

column.

Shelf Mounting

Bracket

Neck Knuckle

Mounting

Points

Mounting Holes

Screwdriver

Phillips Flat

Head Screw

Premier LPWS200 Installation guide

Brand: Premier

Model: LPWS200

Category: Mounting kits

Type: Installation guide

Premier LPWS200

Features:

Adjustable glass shelves allow you to customize the height of the shelves to fit your needs.
Cable management system keeps cords organized and out of sight.
End caps provide a finished look and protect the mounting column from dust.
Easy to install with included hardware and step-by-step instructions.

Possible Use Cases:

Download PDF

report

Premier LPWS200 Installation guide

Premier LPWS200 Installation guide

Related papers

Other documents