BW Technologies GasAlert MicroClip XT Technical Reference

Category
Smoke detectors
Type
Technical Reference

This manual is also suitable for

iERP: XXXXXX
DXXXX/X [language/language]
© BW Technologies 2008. All rights reserved.
1, 2, 3, and 4-Gas Detector
Technical Reference Guide
i
Table of Contents
Heading Page
Introduction ......................................................................................................................................................................... 1
Zeroing the Sensors ........................................................................................................................................................... 1
Contacting BW Technologies by Honeywell .................................................................................................................... 2
Safety Information - Read First.......................................................................................................................................... 2
a Cautions ......................................................................................................................................................................... 3
Sensor Poisons and Contaminants .................................................................................................................................. 6
Getting Started .................................................................................................................................................................... 7
Parts of the GasAlertMicroClip XT .................................................................................................................................... 8
Display Elements ................................................................................................................................................................ 9
Pushbutton ........................................................................................................................................................................ 10
Activating the Detector..................................................................................................................................................... 11
Self-Test ........................................................................................................................................................................ 11
Battery Test .............................................................................................................................................................. 11
Audible/Visual Test................................................................................................................................................... 11
Detector Version....................................................................................................................................................... 11
Startup Message ...................................................................................................................................................... 12
Alarm Setpoints ........................................................................................................................................................ 12
Sensor and Power Test ............................................................................................................................................ 12
Automatic Zero and O
2
Calibration (optional)........................................................................................................... 13
Calibration Due Date (optional) ................................................................................................................................ 13
GasAlertMicroClip XT
Technical Reference Guide
Title Page
ii
Last Calibration Failed (optional) .............................................................................................................................. 14
Overdue Calibration .................................................................................................................................................. 14
Cal IR Lock ............................................................................................................................................................... 14
Bump Test ................................................................................................................................................................ 14
Last Bump Test Failed .............................................................................................................................................. 15
Force Bump (optional) .............................................................................................................................................. 15
Self-Test Pass................................................................................................................................................................ 16
Self-Test Fail.................................................................................................................................................................. 16
Battery Test.................................................................................................................................................................... 16
Backlight ........................................................................................................................................................................ 16
Deactivating the Detector................................................................................................................................................. 17
Installing Fleet Manager II ................................................................................................................................................ 18
Using Fleet Manager II to Configure the Detector ......................................................................................................... 19
Detector Identification ...................................................................................................................................................... 21
Serial Number ........................................................................................................................................................... 21
Hardware/Firmware Revision......................................................................................................................................... 21
Startup Message ............................................................................................................................................................ 21
Sensor Configuration ....................................................................................................................................................... 22
Sensor Disabled............................................................................................................................................................. 22
Calibration Gas Concentration.................................................................................................................................. 23
Calibration Interval ......................................................................................................................................................... 23
Bump Interval................................................................................................................................................................. 24
Low Alarm ...................................................................................................................................................................... 24
High Alarm ..................................................................................................................................................................... 24
TWA Alarm..................................................................................................................................................................... 24
STEL Alarm.................................................................................................................................................................... 25
STEL Interval ................................................................................................................................................................. 25
iii
GasAlertMicroClip XT
Technical Reference Guide
Title Page
Auto Zero on Startup...................................................................................................................................................... 25
O2 Auto-Calibration on Startup (Automatic O
2
Calibration) ........................................................................................... 26
LEL By Vol CH4 ............................................................................................................................................................. 26
User Options...................................................................................................................................................................... 26
Cal Lock (Calibration IR Lock) ....................................................................................................................................... 27
The detector is shipped with
Cal Lock disabled. ................................................................................................................ 27
Confidence Beep ........................................................................................................................................................... 27
Confidence Beep and IntelliFlash Interval ..................................................................................................................... 27
Datalog Interval.............................................................................................................................................................. 27
Force Bump When Overdue .......................................................................................................................................... 28
Force Calibration When Overdue .................................................................................................................................. 28
IntelliFlash...................................................................................................................................................................... 29
Latching Alarms ............................................................................................................................................................. 29
Low Alarm Acknowledge................................................................................................................................................ 29
Safe Mode...................................................................................................................................................................... 29
Stealth Mode.................................................................................................................................................................. 30
Language Menu................................................................................................................................................................. 30
Alarms ................................................................................................................................................................................ 31
Computed Gas Exposures ............................................................................................................................................. 33
Viewing Gas Exposures ................................................................................................................................................. 33
Clearing Gas Exposures ........................................................................................................................................... 34
Gas Alarm Setpoints ...................................................................................................................................................... 34
Factory Gas Alarm Setpoints ......................................................................................................................................... 35
Changing Alarm Setpoints ............................................................................................................................................. 35
Stopping a Gas Alarm .................................................................................................................................................... 35
Sensor Alarm ................................................................................................................................................................. 36
Low Battery Alarm.......................................................................................................................................................... 36
GasAlertMicroClip XT
Technical Reference Guide
Title Page
iv
Automatic Deactivation Alarm ........................................................................................................................................ 36
Bump Test.......................................................................................................................................................................... 37
Calibration ......................................................................................................................................................................... 38
Guidelines ...................................................................................................................................................................... 38
Diagnostics Test ............................................................................................................................................................ 38
Connecting the Gas Cylinder to the Detector ................................................................................................................ 39
Calibration Setup ........................................................................................................................................................... 40
Setting Span Gas Concentration Values .................................................................................................................. 40
Calibrating with the IR Link ....................................................................................................................................... 41
Calibration Procedure ............................................................................................................................................... 41
Auto Zero and Oxygen Sensor Calibration ............................................................................................................... 42
Auto Span ................................................................................................................................................................. 42
Calibration Due Date ................................................................................................................................................ 43
Verification ................................................................................................................................................................ 45
Datalogs ............................................................................................................................................................................. 46
Event Logs......................................................................................................................................................................... 46
Downloading Datalogs and Event Logs ......................................................................................................................... 46
Software Requirements ................................................................................................................................................. 46
Maintenance ...................................................................................................................................................................... 46
Battery Cautions ............................................................................................................................................................ 47
Charging the Battery ...................................................................................................................................................... 47
Replacing a Sensor or Sensor Filter .............................................................................................................................. 49
Replacing the Sensor Filter............................................................................................................................................ 50
Replacing the H
2
S, CO, and LEL sensor ....................................................................................................................... 50
Replacing the Oxygen Sensor ....................................................................................................................................... 51
Reassembling the detector ............................................................................................................................................ 52
Troubleshooting................................................................................................................................................................ 53
v
GasAlertMicroClip XT
Technical Reference Guide
Title Page
Startup Troubleshooting .................................................................................................................................................. 56
Calibration Troubleshooting ............................................................................................................................................ 57
Replacement Parts and Accessories .............................................................................................................................. 58
Specifications.................................................................................................................................................................... 60
General Datalogger Specifications ................................................................................................................................ 61
GasAlertMicroClip XT
Technical Reference Guide
Title Page
vi
vii
List of Figures
Figure Title Page
1. Parts of the GasAlertMicroClip XT......................................................................................................................... 8
2. Display Elements................................................................................................................................................... 9
3. Connecting the IR Link ........................................................................................................................................ 20
4. Detector Identification.......................................................................................................................................... 21
5. CO Sensor Configuration .................................................................................................................................... 22
6. Disabled Sensor .................................................................................................................................................. 22
7. Fleet Manager II IR Link User Options ................................................................................................................ 26
8. Connecting the Gas Cylinder to the Detector...................................................................................................... 39
9. Connecting the Detector and IR Link. ................................................................................................................. 40
10. Connecting the Charging Adapter ....................................................................................................................... 47
11. Replacing a Sensor or Sensor Filter ................................................................................................................... 49
12. Sensor Positioning .............................................................................................................................................. 51
13. Replacing the Rear Shell..................................................................................................................................... 52
viii
GasAlertMicroClip XT
Technical Reference Guide
ix
List of Tables
Table Title Page
1. Gases Monitored ................................................................................................................................................... 1
2. International Symbols............................................................................................................................................ 5
3. Parts of the GasAlertMicroClip XT......................................................................................................................... 8
4. Display Elements................................................................................................................................................... 9
5. Pushbutton .......................................................................................................................................................... 10
6. Connecting the IR Link ........................................................................................................................................ 19
7. Alarms ................................................................................................................................................................. 31
8. Computed Gas Exposures .................................................................................................................................. 33
9. Gas Alarm Setpoints ........................................................................................................................................... 34
10. Sample Factory Alarm Setpoints ......................................................................................................................... 35
11. Connecting the Gas Cylinder to the Detector...................................................................................................... 39
12. Connecting the Charging Adapter ....................................................................................................................... 48
13. Replacing a Sensor or Sensor Filter ................................................................................................................... 50
14. Troubleshooting................................................................................................................................................... 53
15. Replacement Parts and Accessories .................................................................................................................. 58
x
GasAlertMicroClip XT
Technical Reference Guide
1
GasAlertMicroClip XT
Introduction
a Warning
To ensure personal safety, read Safety Information - Read
First and the Cautions before using the detector.
The GasAlertMicroClip XT (“the detector”) warns of hazardous gas at
levels above user-defined alarm setpoints.
The detector is a personal safety device. It is your responsibility to
respond properly to the alarm.
Table 1.
lists the gases monitored.
Zeroing the Sensors
To zero the sensors, refer to steps #1-3 in Calibration Procedure.
Table 1. Gases Monitored
Gas Detected Unit of Measure
Hydrogen sulfide (H
2
S)
parts per million (ppm)
Carbon monoxide (CO) parts per million (ppm)
Oxygen (O
2
)
percent by volume (%)
Combustible gases (LEL)
Field selectable for:
1. percent of lower explosive
limit (% LEL)
2. percent by volume
methane 0-5.0% v/v
GasAlertMicroClip XT
Technical Reference Guide
2
Contacting BW Technologies by Honeywell
To contact BW Technologies by Honeywell, call
USA: 1-888-749-8878
Canada: 1-800-663-4164
Europe: +44 (0) 1295 700300
Other countries: +1-403-248-9226
Address correspondence to
BW Technologies by Honeywell
2840 – 2 Avenue S.E.
Calgary, AB T2A 7X9
CANADA
BW Technologies by Honeywell's website: www.gasmonitors.com
ISO 9001
Safety Information - Read First
Use the detector only as specified in this guide and the operator’s man-
ual, otherwise the protection provided by the detector may be impaired.
International symbols on the detector and in this manual are explained
in Table 2.
Read the Cautions on the following pages before using the detector.
ec Warning
This instrument contains a lithium polymer battery. Dispose of
lithium cells immediately. Do not disassemble and do not
dispose of in fire. Do not mix with the solid waste stream.
Spent batteries must be disposed of by a qualified recycler or
hazardous materials handler.
3
GasAlertMicroClip XT
a
Cautions
a Cautions
Warning: Substitution of components may impair Intrinsic Safety.
Before using the detector, refer to Sensor Poisons and Contaminants
.
Warning: For safety reasons, this equipment must be operated and serviced by qualified personnel only. Read and understand the
user manual completely before operating or servicing.
Do not use the detector if it is damaged. Inspect the detector before using. Look for cracks and/or missing parts.
If the detector is damaged or parts are missing, contact BW Technologies by Honeywell
immediately.
Only use sensor(s) that are specifically designed for the GasAlertMicroClip XT. Refer to Replacement Parts and Accessories
.
Calibrate the detector before first-time use and then on a regular schedule, depending on use and sensor exposure to poisons and
contaminants. BW recommends calibrating at least once every 180 days (6 months).
BW recommends to “bump test” the sensors before each day’s use to confirm their ability to respond to gas by exposing the
detector to a gas concentration that exceeds the alarm setpoints. Manually verify that the audible and visual alarms are activated.
Calibrate if the readings are not within the specified limits.
BW recommends the combustible sensor be checked with a known concentration of calibration gas after any known exposure to
catalyst contaminants/poisons (sulfur compounds, silicon vapors, halogenated compounds, etc).
The combustible sensor is factory calibrated to 50% LEL methane. If monitoring a different combustible gas in the % LEL range,
calibrate the sensor using the appropriate gas.
Caution: High off-scale readings may indicate an explosive concentration.
Only the combustible gas detection portion of this instrument has been assessed for performance by CSA International.
Protect the combustible sensor from exposure to lead compounds, silicones, and chlorinated hydrocarbons.
Sensor exposure to certain organic vapors (such as leaded gasoline and halogenated hydrocarbons) may temporarily inhibit sensor
performance. After exposure, a bump test or calibration is recommended.
4
GasAlertMicroClip XT
Technical Reference Guide
a Cautions
For use only in potentially explosive atmospheres where oxygen concentrations do not exceed 20.9% (v/v).
Any rapid up-scaling reading followed by a declining or erratic reading may indicate a gas concentration beyond upper scale limit,
which may be hazardous.
Only calibrate the detector in a fresh air environment and in a safe area.
Use only BW approved batteries for the GasAlertMicroClip XT detector. Refer to Specifications
.
Charge the detector before first-time use. BW recommends the detector be charged after every workday.
Charge the detector using the recommended charging adapter only. Do not use any other charging adapter. Failure to adhere to this
caution can lead to fire and/or explosion.
Extended exposure of the detector to certain concentrations of combustible gases and air may stress a detector element that can
seriously affect its performance. If an alarm occurs due to high concentration of combustible gases, calibrate the detector. If necessary,
replace the sensor.
Do not test the combustible sensor’s response with a butane cigarette lighter; doing so will damage the sensor.
Do not expose the detector to electrical shock and/or severe continuous mechanical shock.
Do not attempt to disassemble, adjust, or service the detector unless instructions for that procedure are provided in the technical
reference guide, and/or that part is listed as a replacement part. Use only BW Technologies by Honeywell replacement parts. Refer to
Replacement Parts and Accessories
.
The detector warranty will be voided if customers, personnel, or third parties damage the detector during repair attempts. Non-BW
Technologies by Honeywell repair/service attempts void this warranty.
5
GasAlertMicroClip XT
a
Cautions
Table 2. International Symbols
Symbols Description
n
Approved to both U.S. and Canadian Standards by CSA International
g
European Explosive Protection
X
Conforms to European Union Directives
ATEX
Conforms to European ATEX Directives
IECEx
International Electrotechnical Commission Scheme for Certification to Standards for Electrical Equipment for Explosive
Atmospheres
GasAlertMicroClip XT
Technical Reference Guide
6
Sensor Poisons and Contaminants
Several cleaners, solvents, and lubricants can contaminate and cause
permanent damage to sensors. Before using cleaners, solvents, and
lubricants in close proximity to the detector sensors, read the following
cautions and refer to the lists below.
a Caution
Use only the following BW Technologies by Honeywell
recommended products and procedures:
Use water based cleaners.
Use non-alcohol based cleaners.
Clean the exterior of the detector with a soft, damp cloth.
Do not use soaps, polishes, or solvents.
Below are common products to avoid using around sensors.
Cleaners and Lubricants
Brake cleaners
•Lubricants
Rust inhibitors
Window and glass cleaners
Dishsoaps
Citrus based cleaners
Alcohol based cleaners
Hand sanitizers
Anionic detergents
Methanol (fuels and antifreezes)
Silicones
Silicone cleaners and protectants
Silicone based adhesives, sealants, and gels
Hand/body and medicinal creams containing silicone
Tissues containing silicone
Mold releasing agents
Polishes
Aerosols
Bug repellents and sprays
•Lubricants
Rust inhibitors
Window cleaners
7
GasAlertMicroClip XT
Getting Started
Getting Started
The list below provides the standard items included with the detector. If
the detector is damaged or parts are missing, contact the place of pur-
chase immediately.
Sensors: H
2
S, CO, O
2
, and combustible (LEL)
Calibration cap and hose
Charging adapter
printed operator‘s manual
Supplementary booklet, including a quick reference card
CD-ROM, including translated operator‘s manuals
Configuration Software
The detector is configured with Fleet Manager II software. It can be
downloaded for free from BW Technologies by Honeywell website:
www.gasmonitors.com
.
Fleet Manager II CD-ROM is shipped with the MicroDock II base station
and IR Link kit.
The detector is shipped with the sensors and rechargeable battery
installed.
Battery Replacement: To replace the battery, contact BW Technolo-
gies by Honeywell. The battery can only be replaced by the manufac-
turer.
Charge Battery and Replace Sensors: To charge the battery and
replace the sensors and/or sensor filter, refer to the following:
Battery Cautions
Replacing a Sensor or Sensor Filter
To order replacement parts, refer to Replacement Parts and Accesso-
ries.
To become oriented with the features and functions of the detector, refer
to the following figures and tables:
Figure 1.
and Table 3. describes the detector’s components.
Figure 2.
and Table 4. describes the detector’s display elements.
Table 5.
describes the detector’s pushbutton.
GasAlertMicroClip XT
Technical Reference Guide
8
Parts of the GasAlertMicroClip XT
Figure 1. Parts of the GasAlertMicroClip XT
Table 3. Parts of the GasAlertMicroClip XT
Item Description
1 IntelliFlash
2 Visual alarm indicators (LEDs)
3 Alligator clip
4 Charging connector / IR interface
5 Pushbutton (C)
6 Carbon monoxide (CO) sensor
7
Hydrogen sulfide (H
2
S) sensor
8
Oxygen (O
2
) sensor
9 Combustible (LEL) sensor
10 Audible alarm
Liquid crystal display (LCD)
9
GasAlertMicroClip XT
Display Elements
Display Elements
Figure 2. Display Elements
Table 4. Display Elements
1
8
7
6
5
4
3
2
Item Description
1 Alarm condition
2 Automatically zero sensor
3 Numeric value
4 Stealth mode
5 Battery life indicator
6 Gas identifier bars
7 Gas cylinder
8 Automatically span sensor
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74

BW Technologies GasAlert MicroClip XT Technical Reference

Category
Smoke detectors
Type
Technical Reference
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI