LevelOne WGR-6012 User manual

1

LevelOne

WGR-6012

300Mbps N_Max Wireless Gigabit Router

User Manual

V1.0

2

Copyright

The contents of this publication may not be reproduced in any part or as a whole, stored, transcribed in an

information retrieval system, translated into any language, or transmitted in any form or by any means,

mechanical, magnetic, electronic, optical, photocopying, manual, or otherwise, without the prior written

permission.

Trademarks

All products, company, brand names are trademarks or registered trademarks of their respective companies.

They are used for identification purpose only. Specifications are subject to be changed without prior notice.

FCC Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against radio

interference in a commercial environment. This equipment can generate, use and radiate radio frequency

energy and, if not installed and used in accordance with the instructions in this manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is likely to cause

interference, in which case the user, at his own expense, will be required to take whatever measures are

necessary to correct the interference.

CE Declaration of Conformity

This equipment complies with the requirements relating to electromagnetic compatibility, EN 55022/A1 Class

B.

The specification is subject to change without notice.

3

Table of Contents

Chapter 1 Introduction .............................................................................. 4

1.1 Packing List ................................................................................. 4

1.2 Spec Summary Table ................................................................. 4

1.3 Hardware ...................................................................................... 5

1.4 LED Indicators ............................................................................. 5

1.5 Procedure for Hardware Installation ........................................ 6

Chapter 2 Getting Start .......................................................................... 10

2.1 Select Language ....................................................................... 10

2.2 Setup mode ............................................................................... 11

2.3 Advanced mode Setup. ............................................................ 11

2.4 Quick Wizard Install mode Setup ........................................... 12

2.5 Wireless Setting. ....................................................................... 12

2.6 Auto Detect WAN Service. ...................................................... 13

2.7. Manual select WAN Service .................................................. 13

2.8 Summary of the settings and Next to “Reboot” .................... 13

2.9 Apply the Settings or Modify. .................................................. 14

2.10 Test the Internet connection. ................................................ 14

2.11 Setup Completed. ................................................................... 15

Chapter 3 Making Configuration ........................................................ 16

3.1 Login to Configure from Wizard .............................................. 17

3.2 System Status ........................................................................... 21

3.3 Advanced ................................................................................... 21

3.3.1 Basic Setting .......................................................................................................... 21

3.3.1.1 Primary Setup – WAN Type, Virtual Computers ........................................... 23

3.3.2 Forwarding Rules .................................................................................................. 36

3.3.3 Security Settings .................................................................................................... 39

3.3.4 Advanced Settings ................................................................................................ 53

3.3.5 Toolbox .................................................................................................................... 61

Appendices and Index ............................................................................ 64

802.1x Setting .................................................................................. 64

1. Equipment Details ....................................................................................................... 64

2. DUT Configuration: ..................................................................................................... 65

3. DUT and Windows 2000 Radius Server Setup ...................................................... 65

4. Windows 2000 RADIUS server Authentication testing: ........................................ 67

WPA Settings ................................................................................... 70

FAQ and Troubleshooting .............................................................. 79

4

C

h

a

p

t

e

r

1

I

n

t

r

o

d

u

c

t

i

o

n

Congratulations on your purchase of this outstanding Wireless Broadband Router. This product is specifically

designed for Small Office and Home Office needs. It provides a complete SOHO solution for Internet surfing,

and is easy to configure and operate even for non-technical users. Instructions for installing and configuring

this product can be found in this manual. Before you install and use this product, please read this manual

carefully for fully exploiting the functions of this product.

1.1 Packing List

 WGR-6012 x1

 RJ-45 Ethernet LAN Cable x1

 Antenna x 2

 Power Adapter x1

 Quick Installation Guide x1

 CD Manual x1

1.2 Spec Summary Table

Device Interface

Ethernet WAN

RJ-45 port, 10/100/1000Mbps, auto-MDI/MDIX

1

Ethernet LAN

RJ-45 port, 10/100/1000Mbps, auto-MDI/MDIX

4

Antenna

2 dBi detachable antenna

2

WPS Button

For WPS connection

1

Wireless

Enable/disable

To enable or disable Wireless Radio

1

LED Indication

Power/Status / WAN / LAN1 ~ LAN4/ Wi-Fi

●

Power Jack

DC Power Jack, powered via external DC 12V/1A

switching power adapter

1

Wireless LAN (Wi-Fi)

Standard

IEEE 802.11b/g/n compliance

●

SSID

SSID broadcast or in stealth mode

●

Channel

Auto-selection, manually

●

Security

WEP, WPA, WPA-PSK, WPA2, WPA2-PSK

●

WPS

WPS (Wi-Fi Protected Setup)

●

WMM

WMM (Wi-Fi Multimedia)

●

Functionality

5

Ethernet WAN

PPPoE, DHCP client, Static IP, PPTP, L2TP

●

WAN Connection

Auto-reconnect, dial-on-demand, manually

●

One-to-Many NAT

Virtual server, special application, DMZ, Super DMZ

(IP Passthrough)

●

NAT Session

Support NAT session

20000

SPI Firewall

IP/Service filter, URL blocking, MAC control

●

DoS Protection

DoS (Deny of Service) detection and protection

●

Routing Protocol

Static route, dynamic route (RIP v1/v2)

●

Management

SNMP, UPnP IGD, syslog, DDNS

●

Administration

Web-based UI, remote login, backup/restore setting

●

Performance

NAT up to 700Mbps and Wireless up to150Mbps

Environment & Certification

Package Information

Package dimension (mm)

Package weight (g)

Operation Temp.

Temp.: 0~40oC, Humidity 10%~90%

non-condensing

●

Storage Temp.

Temp.: -10~70oC, Humidity: 0~95%

non-condensing

●

EMI Certification

CE/FCC compliance

●

RoHS

RoHS compliance

●

1.3 Hardware

1.4 LED Indicators

LED Indicators

Power LED

6

LED status

Description

Status

Green in flash

Device status is working.

WAN LED

Green

RJ-45 cable is plugged

Green in flash

Data access

LAN LED

Green

RJ-45 cable is plugged

Green in flash

Data access

Wi-Fi LED

Green

WLAN is on

Green in flash

Data access

Green in fast flash

Device is in WPS PBC mode

Green in dark

Wi-Fi Radio is disabled

1.5 Procedure for Hardware Installation

7

Step 1. Attach the antenna.

1.1. Remove the antenna from its plastic wrapper.

1.2. Screw the antenna in a clockwise direction to the back panel of the unit.

1.3. Once secured, position the antenna upward at its connecting joint. This will ensure optimal reception.

1.Turn off the Power Switch first.

8

Step 2 Insert the Ethernet cable into LAN Port:

Insert the Ethernet patch cable into LAN port on the back panel of Router, and an available Ethernet port on

the network adapter in the computer you will use to configure the unit.

Step 3 Insert the Ethernet patch cable into Wired WAN port:

Insert the Ethernet patch cable form DSL Modem into Wired WAN port on the back panel of Router.

9

Step 4. Power on Router:

4.1. Connect the power adapter to the receptor on the back panel of your Router and Push Power switch

Step 5. Complete the setup.

5.1. When complete, the Status LED will flash.

10

C

h

a

p

t

e

r

2

G

e

t

i

n

g

S

t

a

r

t

Insert the CD into CD reader on your PC. The program, AutoRun, will be executed automatically. And then you

can click the Easy setup Icon for this utility.

Configure the settings by the following steps.

2.1 Select Language then click “Next”

for continues.

11

2.2 Setup mode

You can select Wizard mode to run the setup

step-by-step or run advanced mode to

diagnose the network settings of the router.

2.3 Advanced mode Setup.

Check the PC, Router or Internet icons for

the Status of PC, Router or Internet.

12

2.4 Quick Wizard Install mode

Setup

1. Make sure the router is powered on.

2. Make sure your network adapter is

connected to the LAN port of the router

3. Make sure your network adapter has an IP

address.

Click “Next” for continues

2.5 Wireless Setting.

Key in the SSID, Channel and Security

options, and then click “Next” for continues.

13

2.6 Auto Detect WAN Service.

Click “Next” for continue.

Click the button, “Let me select WAN service

by myself”, to disable this function.

Note: The Item supports to detect the

Dynamic and PPPoE WAN Services only

Example, the Dynamic WAN type is tected.

2.7. Manual select WAN Service

In the manual mode, Click the any icons for

continues.

2.8 Summary of the settings and

Next to “Reboot”

Click “Next” for continue.

14

2.9 Apply the Settings or Modify.

Click “Next” for continue.

2.10 Test the Internet connection.

Test WAN Networking service. Click “Next”

for continue.

You can ignore the by select the “Ignore

Test”.

15

2.11 Setup Completed.

The EzSetup is finish, you can open the

default web browser to configure advanced

settings of the Router.

Click “Finish” to complete the installation.

16

C

h

a

p

t

e

r

3

M

a

k

i

n

g

C

o

n

f

i

g

u

r

a

t

i

o

n

This product provides Web based configuration scheme, that is, configuring by your Web browser, such as

Mozilla Firefox or Internet Explorer. This approach can be adopted in any MS Windows, Macintosh or UNIX

based platforms.

17

3.1 Login to Configure from Wizard

Type in the IP Address

(HHUhttp://192.168.1.1UHH)

Type password, the default is

“admin” and click „login‟ button.

Press “Wizard” for basic

settings with simple way.

Press “Next” to start wizard.

18

Step 1:

Set up your system password.

Step 2:

Select Wan Type.

Auto Detecting or

Setup Manually.

19

Step 3:

Setup the LAN IP and WAN

Type.

Step 4:

Please fill in PPPoE service

information which is provided by

your ISP.

Example:

Step 5:

Set up your Wireless.

20

Set up your Authentication and

Encryption.

Step 6:

Then click Apply Setting.

And then the device will reboot.

Step 7:

Click Finish to complete it.

Page is loading ...

LevelOne WGR-6012 User manual

LevelOne WGR-6012 User manual

Related papers

Other documents