Nortec 2538144 B NHTC Eng User manual

2538144-B

NH

Series

NHTC / NHPC

ELECTRODE

STEAM HUMIDIFIER

Engineering Manual

TM

2008-10-01

PROPRIETARY NOTICE

This document and the information disclosed herein are proprietary data of WALTER MEIER LTD.

Neither this document nor the information contained herein shall be reproduced used, or disclosed to

others without the written authorization of WALTER MEIER LTD., except to the extent required for

installation or maintenance of recipient’s equipment. All references to the NORTEC name should be

taken as referring to WALTER MEIER LTD.

LIABILITY NOTICE

NORTEC does not accept any liability for installations of humidity equipment installed by unqualified

personnel or the use of parts/components/equipment that are not authorized or approved by

NORTEC.

COPYRIGHT NOTICE

SPECIFICATION LABEL LOCATION

The Specification Label for your NH Series humidifier is located on the bottom of the unit. You will

find it attached to the skirt that separates the electrical and plumbing compartments on the electrical

compartment side.

RECORD OF REVISIONS

For each revision, put the revised pages in your manual and discard the superseded pages. Write the

revision number and revision date, date put in manual, and the incorporator’s initials in the applicable

columns on the Record of Revisions.

Revision

Number

Revision

Date

Date Put

In Manual By

Revision

Number

Revision

Date

Date Put

In Manual By

2008-10-01

TABLE OF CONTENTS

Subject Page

10-00 ELECTRODE STEAM ENGINEERING

1. INTRODUCTION WHY ELECTRODE STEAM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

A. PROPORTIONAL + INTEGRAL AUTO-ADAPTIVE CONTROL SYSTEM FOR

THE NHTC/NHPC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

B. NH CAPACITY ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

C. DRAIN CYCLE AND CYLINDER LIFE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

2. PRE-INSTALLATION EQUIPMENT VERIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

A. GENERAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

10-10 HUMIDITY, STEAM ABSORPTION AND DISTRIBUTION

1. HUMIDITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

A. ESTIMATING THE HUMIDIFICATION LOAD . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

B. LOAD CALCULATION SUMMARY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

C. TEMPERATURE AND HUMIDITY REQUIRED . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

D. TEMPERATURE AND HUMIDITY AVAILABLE . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

E. INCOMING AIR VOLUME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

2. STEAM ABSORPTION AND DISTRIBUTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

A. VARIABLES THAT AFFECT ABSORPTION DISTANCES. . . . . . . . . . . . . . . . . . . . 28

B. CALCULATING THE DOWN STREAM HUMIDITY LEVEL . . . . . . . . . . . . . . . . . . .30

C. CONTROL OF DUCT OR PLENUM SATURATION. . . . . . . . . . . . . . . . . . . . . . . . .31

3. STEAM RUNS AND CONDESNATE RETURNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

A. STEAM RUNS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

B. CONDENSATE RETURN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

4. STEAM DISTRIBUTORS (ASD, BSD, CSD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

A. STEAM DISTRIBUTORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

B. DISTRIBUTOR CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

C. DISTRIBUTOR LOCATIONS AND MOUNTING . . . . . . . . . . . . . . . . . . . . . . . . . . .38

D. MULTIPLE DISTRIBUTOR APPLICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

E. LOCATION OF STEAM DISTRIBUTORS WITHIN AN AIR HANDLER . . . . . . . . . . 40

F. DISTRIBUTOR ABSORPTION DISTANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

G. TYPICAL APPLICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

H. DISTRIBUTOR DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

5. SHORT ABSORPTION MANIFOLD (SAM-e) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

A. GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

B. DETERMINING THE STEAM ABSORPTION DISTANCE . . . . . . . . . . . . . . . . . . . .43

C. STATIC AIR PRESSURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

D. CONDENSATE LOSSES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

E. CORRECT CHOICE OF PRODUCT APPLICATIONS (WITHIN SAM-e) . . . . . . . .46

F. SAM-e DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

G. SAM-e HEADER SELECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

H. SAM-e STEAM TUBE SELECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

I. SAM-e STEAM INLET CONFIGURATION SELECTION . . . . . . . . . . . . . . . . . . . . .48

J. MINI SAM-e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

6. BLOWER PACKS (BOBP, RMBP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

A. BLOWER PACKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

2008-10-01

Subject Page

7. CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

A. GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

B. ON/OFF CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

C. MODULATING CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

D. OUTDOOR TEMPERATURE SETBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

E. TRANSDUCER SENSORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

F. POSITIONING CONTROLS AND SENSORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

G. NORTEC ONLINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

H. NORTEC LINKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

I. TYPICAL INSTALLATION LAYOUT FOR NHTC/NHPC . . . . . . . . . . . . . . . . . . . . . 58

J. NORTEC CONTROLLER DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

10-20 SPECIFICATIONS

1. HUMIDIFIERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

A. GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

B. PRODUCTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

C. EXECUTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

10-30 SUBMITTALS

1. SUBMITTAL DESCRIPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

A. INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

B. NH UNIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

C. DISTRIBUTORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

D. SAM-e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

E. BLOWER PACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

F. CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

WARRANTY

2008-10-01

LIST OF FIGURES

Figure Page

10-00 ELECTRODE STEAM ENGINEERING

Figure 1. NHTC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Figure 2. Optimum Boiling Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Figure 3. Conductivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Figure 4. Typical Auto-Adaptive Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Figure 5. Capacity Setting & Cylinder Life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Figure 6. Output vs Service Life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Figure 7. Typical NHRS Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

10-10 HUMIDITY, STEAM ABSORPTION AND DISTRIBUTION

Figure 1. Schematic of a Typical Print Shop HVAC System . . . . . . . . . . . . . . . . . . . . . . 19

Figure 2. Psychrometric Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Figure 3. Steam Distributor Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Figure 4. Condensate Drain Pan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Figure 5. Proper Slope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Figure 6. Drain Tee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Figure 7. Steam Line Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Figure 8. Condensate Tee At Any Low Point In Steam Line . . . . . . . . . . . . . . . . . . . . . . .35

Figure 9. Trap To Prevent Steam In Condensate Line . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Figure 10. Levelling the Distributor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Figure 11. Single Steam Distributor Installation – Minimum Clearance . . . . . . . . . . . . . . .38

Figure 12. Cutting Duct For Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Figure 13. Humidification Distance Nomogram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Figure 14. Best Location for Multiple Steam Distributors . . . . . . . . . . . . . . . . . . . . . . . . . .40

Figure 15. Roof Top Units 2-20 Tons – Typical Location . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Figure 16. Small Units On Residential Furnaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

Figure 17. SAM-e Tubes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

Figure 18. Cross-Section of Distributor Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

Figure 19. Absorption Distance – 3" Centers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Figure 20. Absorption Distance – 6" Centers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Figure 21. Absorption Distance – 9" Centers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Figure 22. Absorption Distance – 12" Centers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Figure 23. SAM-e Header . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Figure 24. SAM-e Tubes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Figure 25. Steam Inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

Figure 26. Typical SAM-e Installation for Atmospheric Steam Applications . . . . . . . . . . . .50

Figure 27. NH Series Humidifier With Built-On Blower Pack . . . . . . . . . . . . . . . . . . . . . . . .51

Figure 28. NH Series Remote Mounted Blower Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

Figure 29. Set Point Versus Outdoor Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54

Figure 30. NORTEC OnLine Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56

Figure 31. NORTEC Online Configuration Form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59

Figure 32. NORTEC Links Form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60

2008-10-01

Figure Page

Figure 33. Humidifier Controlled by Air Proving, On/Off Duct Mounted High Limit and

Modulating Wall Mounted Space Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Figure 34. Humidifier Controlled by Air Proving, Modulating Duct Mounted High Limit

and Modulating Wall Mounted Space Controller . . . . . . . . . . . . . . . . . . . . . . . . 61

Figure 35. Humidifier Controlled by Air Proving, Modulating Duct Mounted High Limit

and Modulating Wall Mounted Return Air Sensor with Wall Mounted

Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Figure 36. Humidifier Controlled by Air Proving, Duct Mounted High Limit Sensor

and Modulating Duct Mounted Return Air Sensor with Networking Option . . . . 62

10-30 SUBMITTALS

Figure 1. Low Voltage Control Terminal Strip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Figure 2. Primary (Line) Voltage Wiring to Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Figure 3. Physical Data - NHTC/NHPC 005-030 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Figure 4. Physical Data - NHTC/NHPC 050-100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Figure 5. Physical Data - NHTC/NHPC 150-200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Figure 6. Distributor Dimensions (3 Sheets) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Figure 7. SAM-e General Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Figure 8. General Mini SAM-e Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

Figure 9. In-Duct/AHU Installation Without Mounting Frame Installation . . . . . . . . . . . . . 87

Figure 10. In-Duct/AHU Installation With Mounting Frame Installation . . . . . . . . . . . . . . . . 88

Figure 11. Outside Duct Installation Without Mounting Frame Installation . . . . . . . . . . . . . 89

Figure 12. Outside Duct Installation With Mounting Frame Installation . . . . . . . . . . . . . . . . 90

Figure 13. Vertical Duct Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Figure 14. Outside Duct Mounting Cover Plates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Figure 15. Atmospheric SAM-e Adapter Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

Figure 16. Atmospheric Steam Header and Adapter Configuration . . . . . . . . . . . . . . . . . . 93

Figure 17. Physical Data for Remote Mounted Blower Pack . . . . . . . . . . . . . . . . . . . . . . . 94

Figure 18. Physical Data Units With Optional Built-On Blower Packs . . . . . . . . . . . . . . . . . 95

Figure 19. Wall Digital Humidistat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

Figure 20. Duct Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

2008-10-01

LIST OF TABLES

Table Page

10-00 ELECTRODE STEAM ENGINEERING

Table 1. Features Comparison . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Table 2. NHTC/NHPC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

10-10 HUMIDITY, STEAM ABSORPTION AND DISTRIBUTION

Table 1. Outdoor/Indoor Relative Humidity Conversion Chart . . . . . . . . . . . . . . . . . . . . 14

Table 2. Load Calculation Summary Sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Table 3. Grains of Water Per Cubic Foot – Saturated Air (100% rh) . . . . . . . . . . . . . . . 15

Table 4. Design Outdoor Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Table 5. Inside Relative Humidities At Which Moisture Will Condense On Windows . . 21

Table 6. Regain of Hygroscopic Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Table 7. Design Indoor Conditions For Various Places, Products and Processes . . . . . . 23

Table 8. Variables That Affect Absorption Distances . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Table 9. Typical Absorption Distances, Single Distributor, 100 lbs/hr Humidifier . . . . . . .29

Table 10. Water (lbs/hr) Contained in 1000 CFM of Air . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Table 11. Steam Line Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Table 12. Recommended Material and Size for Steam Run . . . . . . . . . . . . . . . . . . . . . . .33

Table 13. Recommended Condensate Line at Distributor(s) . . . . . . . . . . . . . . . . . . . . . . .33

Table 14. Maximum Recommended Length of Steam Runs . . . . . . . . . . . . . . . . . . . . . . .34

Table 15. Air Pressure Loss in AHU/Duct . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

Table 16. Condensate Loss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Table 17. SAM-e Tube Matrix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Table 18. Mini SAM-e Headers – 3" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

Table 19. Mini SAM-e Headers – 6" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

Table 20. Mini SAM-e Tubes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

Table 21. Mini Inlet Configurations – For Atmospheric Steam Unit . . . . . . . . . . . . . . . . . .49

Table 22. Ceiling and Frontal Clearances for Blower Packs . . . . . . . . . . . . . . . . . . . . . . .52

10-30 SUBMITTALS

Table 1. NH Series Unit Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99

Table 2. Common Accessories Universal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100

Table 3. Steam Distributors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100

Table 4. Steam Distributor Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101

Table 5. SAM-e Header . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103

Table 6. Adjustable Mounting Frame for SAM-e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106

Table 7. SAM-e Tube Matrix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106

Table 8. SAM-e Inlet and Adapter Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110

Table 9. Remote Blower Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111

Table 10. Built-On Blower Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111

Table 11. Controls – ON/OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112

Table 12. Modulating Control By NORTEC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112

2008-10-01

Table Page

Table 13. Modulating Demand Signal By Others Single Channel. . . . . . . . . . . . . . . . . . . 113

Table 14. Modulating Demand Signal By Others Dual Channel. . . . . . . . . . . . . . . . . . . . 113

Table 15. Modulating By Other Transducer Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113

Table 16. NORTEC OnLine Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114

Table 17. NORTEC Links Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114

Table 18. NH Series Fusing Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114

10-00

Page 1

2008-10-01

10-00

INTRODUCTION

10-00

Page 2

2008-10-01

Figure 1. NHTC

10-00

Page 3

2008-10-01

1. INTRODUCTION

The NHTC humidifier is controlled by Nortec’s Patented Auto adaptive Water Management

Control System. This system allows the humidifiers to adapt to basically any potable

incoming water and changes that occur to the water supply. This eliminates the need to

readjust drain timers, changes complete cylinders or time consuming adjustment of

electrode spacing’s. The system also adjusts the drain rate of the humidifier to reduce the

amount of drain water exiting the humidifier as water conditions change. This reduces

energy loss due to excessive draining of hot water and extends cylinder life since less water

and minerals enter the humidifier.

The following is a brief description of how the Auto-Adaptive water Management System

works.

The electrode steam system produces pure uncontaminated steam with variable output

through electronic power control of the electrodes. Water borne minerals remain in the

cylinder and are periodically flushed out through the automatic cylinder drain. On NHTC and

NHPC models the drain automatically empties the steam cylinder if it is not operated for

three days. Solid mineral scale sinks to the bottom of the cylinder which, when filled with

residue, is easily removed and replaced.

A. PROPORTIONAL + INTEGRAL AUTO-ADAPTIVE CONTROL SYSTEM FOR THE

NHTC/ NHPC

(1) NORTEC’s patented P+I Auto-Adaptive control system allows the unit to operate at

an optimal low water level using the same fixed electrode spacing regardless of the

incoming water conditions. Boiling of the water allows the minerals in the water to

remain behind in the cylinder. This raises the contained water conductivity to a

value higher than the incoming water. The P+I Auto-Adaptive control system

monitors and adjusts the contained water conductivity as these changes occur.

(2) The humidifiers are designed to produce full steam output at the lowest possible

electrode coverage to obtain maximum cylinder life.

(3) The units operate between A and D of the main steam output demand.

Accordingly, the current flow between the electrodes in the cylinder is maintained

between these pre-established limits programmed into the P+I Auto-Adaptive

control system.

(4) As the water boils away and the electrode coverage is reduced, the steam output is

also reduced slightly. A pre-determined design parameter of every NORTEC

cylinder is the known time (To) (time optimum) that it takes to boil down from A to

D of output (also referenced to as amp trigger points) at a pre-designed contained

water conductivity. (See Figure 2.)

(5) Whenever the conductivity in the cylinder water is lower than the designed

conductivity, the (Ta) (time actual) to boil down from A to D will be longer than the

To. (See Figure 3.)

10-00

Page 4

2008-10-01

(6) As the water is boiled away, the minerals left behind increase the conductivity of

the water in the cylinder. As soon as the conductivity is greater than design, the Ta

to boil from A to D will be shorter than To and a drain cycle is initiated.

(7) The fill valve always opens during timer drains, adding cold water to mix with the

hot water from the cylinder during automatic drain cycles. This tempering process

is required to meet plumbing codes.

(8) As can be seen from a typical sequence depicted in Figure 4, the P+I Auto-

Adaptive system allows the unit to be self-regulating. It drains only when necessary

and only the amount of water to maintain optimum operating conditions.

(9) Relying on the proportional (P) feedback only to decide how much to drain is like

guessing what is happening based on a ‘snapshot’ only. By taking into

consideration a series of “snapshots”: (one from each of the past ten cycles for

example), the control system has more data on which to base its decision to drain.

The integral (I) part of the P+I Auto-Adaptive system provides this added feedback.

(10) The proportional (P) and integral (I) factors have been weighted as to the relative

influence each will have when the NHTC/NHPC calculates a drain. The

preprogrammed weighing was derived through extensive field and laboratory tests.

When supply water conductivity is extremely high (requiring substantially more

drains), the NHTC/NHPC will see the pattern developing in cycles stored in

memory. It will then initiate additional drains to adjust the contained water

conductivity.

(11) If low conductive water conditions occur, the P+I control will reduce the drains

necessary to maintain optimum operating conditions within the cylinder. If extreme

water conditions are encountered, the NHTC/NHPC can be reprogrammed with

factory instructions to compensate.

(12) NORTEC’s P+I Auto-Adaptive control system has been designed to benefit users

who demand very tight control of the relative humidity. It maintains steam output

above the B level, even during auto drains. (See Figure 4.)

(13) The P+I Auto-Adaptive control system allows the humidifier to maintain tighter

humidity control without the problem of rh depression during drain cycles that occur

with other humidifiers. This results in more consistent space rh levels, even with a

simple on/off control system.

10-00

Page 5

2008-10-01

Figure 2. Optimum Boiling Time

Figure 3. Conductivity

10-00

Page 6

2008-10-01

B. NH CAPACITY ADJUSTMENT

(1) Each NORTEC NH Series humidifier is rated at its maximum output capacity. By

means of the alphanumeric display and keypad on the NHTC/NHPC, the

humidifiers can be adjusted to obtain an output between 20% and 100% of its rated

capacity.

C. DRAIN CYCLE AND CYLINDER LIFE

(1) Water Type Used (Potable or Softened)

(a) The electrode steam product line is one of the most efficient humidifier

systems since it uses the minerals in the water to conduct electricity. If no

minerals are present no current can pass from one electrode to another, thus

no steam production can occur.

(b) Although the electrode steam humidifier is ideal for potable water, it should

not be used with pure reverse osmosis or deionized water since the

conductivity is too low.

(2) Water Conditions vs Cylinder Life

(a) The NH Series is designed to adapt to most potable or softened water

supplies. Since the output of all NH Series humidifiers is pure, clean steam,

minerals originally in the incoming water are left behind in the steam cylinder.

Many of these minerals will be removed during short flush cycles within the

cylinder. Therefore, the water chemistry, the unit running time, and output

capacity setting ultimately determines the cylinder life. (See Figure .)

(3) Output vs Cylinder Life

(a) As minerals build-up on the electrodes in the cylinder of the NORTEC NH

Series humidifier, the patented P+I Auto-Adaptive control system

automatically raises the water level slightly in the cylinder. This exposes fresh

electrode surface to the water and maintains peak output and efficiency from

the humidifier. Once the

(b) electrode surface is completely encrusted by the minerals, the user is alerted

to change the cylinder. Other humidifiers’ performance degrades gradually as

the minerals build-up. The NH Series maintains maximum efficiency then the

cylinder is replaced. (See Figure .)

(4) Water Conditions vs Drain Rate

(a) The P+I Auto-Adaptive control system automatically adjusts the drain rate to

maintain the design water conductivity required for proper operation. This

ensures regular flushing of minerals which become concentrated in the water,

and minimizing wastage of hot water. The humidifier automatically adjusts it’s

drain rate with changes in incoming water conductivity through the Auto-

adaptive water management system.

10-00

Page 7

2008-10-01

Figure 4. Typical Auto-Adaptive Operation

0. Store previous cycle’s drain decision in integral (l) memory.

1. Fill to A trigger (use all places below 1-10).

2. Boil to C trigger without timing to allow previous fill water to mix thoroughly during boiling.

3. Boil from C to D while monitoring time (T actual).

4. Decide how long (how much) to drain, then fill to B.

5. Drain according to the P+I calculated drain time, fill on to control outlet temperature.

6. At D, stop draining and postpone remaining drain, fill to B.

7. Continue remaining drain.

8. With drain finished, fill to A.

9. Boil to D, timing from C to D.

10. Decide how long to drain (in this case zero) based on present and past cycles.

10-00

Page 8

2008-10-01

It is important to note that the drain rate shown includes the make-up water,

mixed with the drain water, which tempers the drain water to 140°F (60°C) or

less.

NOTE

The electrode steam process provides optimum efficiency because all resistance to

current passage is converted to usable energy. Unlike cal-rod or infrared humidifiers

which convert some of their capacities into unusable heat.

Figure 5. Capacity Setting & Cylinder Life

Figure 6. Output vs Service Life

10-00

Page 9

2008-10-01

3. PRE-INSTALLATION EQUIPMENT VERIFICATION

A. GENERAL

(1) Ensure the available voltage and phase correspond with humidifier voltage and

phase as indicated on the humidifier’s specification label.

(2) Ensure that the external fuse disconnect is sufficient size to handle the rated

amperage as indicated on the humidifier’s specifications label. Refer to local building

codes.

(3) Report any discrepancy immediately to the site engineer.

(4) Location and mounting is described in Chapter 10-10.

(5) For typical installation see Figures 6 & 7.

10-00

Page 10

2008-10-01

Figure 6. Typical NHRS Installation (Sheet 1 of 2)

10-00

Page 11

2008-10-01

Figure 7. Typical NHRS Installation (Sheet 2 of 2)

10-10

Page 12

2008-10-01

10-10

HUMIDITY,

STEAM ABSORPTION

AND

DISTRIBUTION

Page is loading ...

Nortec 2538144 B NHTC Eng User manual

This manual is also suitable for

Nortec 2538144 B NHTC Eng User manual

Related papers

Other documents