Heath Zenith SL-6171 User manual

Battery

Your doorbell includes (Product style of button and chime may vary from

illustrations):

• Doorbell chime

• Doorbell button/transmitter (model 6162 includes 2) w/battery

• Hardware pack

You'll need to buy 3 "D" alkaline batteries for the chime. In typical use,

alkaline batteries will last up to three years.

Chime

Volume

3. Before mounting, test the doorbell range.

Put the chime where you want to mount it

and temporarily place the doorbell button on

the doorjamb. Press the doorbell button.

2.Install the 3

alkaline "D"

batteries.

Make sure

the batteries

are oriented

properly.

Operation

Press the doorbell button to verify that the doorbell and chime work

properly. If the chime does not sound see the Troubleshooting guide on

page 4.

SL-6153/62/71/72

Wireless Doorbell

1.To open the chime case: press

in the catch on the bottom of the

chime and lift the case open.

4. Mount the doorbell button and chime.

Use either screws or double sided tape to

mount the doorbell button.

To mount with screws, remove the back of the

case by pushing in the tab on the bottom with

a small screwdriver.

-2-

595-5611-05

When attaching the doorbell button using the double sided tape, make sure

the surface of the door jamb or wall is clean.

The chime can be mounted by using the 3 holes in the back of the case, or by

using 2 screws with the keyholes.

3-5/16"

(84 mm)

Chime Back Case

Keyhole Mounting

Chime Back

Case Mounting

Close Chime Case

Snap the front of the chime case back on. Start with the top edge of the case

aligned with the top of the back plate.

Code and Tune Settings

Code Settings

Note: Most installations will not require you to change any of the jump-

ers on your doorbell.

The doorbell button and chime communicate by using a code that can be

changed by removing and/or adding jumpers on both the doorbell button and

chime. The code is factory set; however, there are 128 selectable codes that

allow you to expand your system and prevent outside interference. Another

wireless doorbell system or other wireless products may cause interference

and the system may not function properly. Follow the instructions below for

setting a new code.

1. Disconnect the power to the doorbell button and chime.

2. Open the cases and locate the jumpers on both the doorbell button and

chime (See illustration).

Attach the back of the

case to the door jamb or

wall. Snap the front of

the button back on.

Holes for

Wall

Mounting

-3-

595-5611-05

eryBattery

BBattery

12345678

Doorbell Button Battery Replacement

Install an alkaline type A23 12 Volt battery. The

positive terminal should be positioned as shown.

* Code Settings 1-7

Must Match Both

Doorbell Button

and Chime

Inside

Doorbell

Button

Inside Chime

3. The doorbell button and chime both have eight different jumper locations.

The jumper positions 1 through 7 are used for setting the code.

4. To change the code, add and/or remove jumpers as needed. There are

128 different combinations. It is recommended to only change one jumper

at a time and then check to see if system is functioning properly. Note:

Jumpers in positions 1 through 7 must be exactly the same for both the

doorbell button and chime for this system to function.

Tune Settings

Your Heath

®

/Zenith wireless doorbell has 3 different selectable tunes: Ding

(one note), Ding-Dong (two note), or Westminster (eight note). The factory

setting is for the Westminster; however, this can be changed by following the

instructions below.

• Ding (one note tune)

Doorbell button: Add a jumper to location 8.

• Ding-Dong (two note tune)

Doorbell button: Remove jumper from location 8.

Chime: Remove jumper from location 8.

• Westminster (Eight note tune)

Doorbell button: Remove jumper from location 8.

Chime: Add a jumper to location 8.

Note: Model 6162 has doorbell buttons for both front and back door. The

back door must use the Ding tune and the front door may use either the

Ding-Dong or Westminster tune.

Tune

Setting

-4-

595-5611-05

Troubleshooting

Chime does not sound:

• Make sure the doorbell button and the chime codes are the same (See

pages 2 and 3).

• Check orientation of doorbell button battery (See page 3).

• Check the doorbell button and chime batteries, replace if necessary.

Batteries seem OK, but the chime does not work when installed:

• Do not mount the chime or doorbell button on metal or near metal studs.

This reduces the transmitter range. Use 1/4" to 1/2" (6 to 13 mm) wood

shims to move the chime or doorbell button off the metal surface.

• Don't mount the chime too close to ground level concrete slabs. This may

also reduce the range. Mount the chime away from the floor.

•Try different locations for the chime closer to the doorbell button. Also try

to orient the chime at a different angle to increase the range.

The range of the doorbell depends on location, temperature and battery

condition.

Regulatory Information

This device (SL-6195-RX, WB-94A-TX) complies with Part 15 of the FCC

Rules and RSS-210 of Industry Canada. Operation is subject to the follow-

ing two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference

that may cause undesired operation.

The user is cautioned that changes or modifications not expressly approved

by the party responsible for regulatory compliance could void the user’s au-

thority to operate the equipment.

No Service Parts Available for this Product

Technical Service

(Do Not Send Products)

If you experience a problem, follow this guide. You may also want to visit our Web

site at: www.desatech.com. If the problem persists, call* for assistance at 1-

800-858-8501, 7:30 AM to 4:30 PM CST (M-F). You may also write* to:

DESA Specialty Products™

P.O. Box 90004, Bowling Green, KY 42102-9004

ATTN: Technical Service Specialty Products

* If contacting Technical Service, please have the following information avail-

able: Model Number, Date of Purchase, and Place of Purchase.

-5-

595-5611-05

DESA Specialty Products™ reserves the right to discontinue and to change

specifications at any time without notice without incurring any obligation to

incorporate new features in previously sold products.

FIVE YEAR LIMITED WARRANTY

This is a "Limited Warranty" which gives you specific legal rights. You may

also have other rights which vary from state to state or province to province.

For a period of five years from the date of purchase, any malfunction

caused by factory defective parts or workmanship will be corrected at no

charge to you. Batteries are not covered. To obtain a refund or a

replacement, return the product to the place of purchase.

Not Covered - Repair service, adjustment and calibration due to misuse,

abuse or negligence, light bulbs and other expendable items are not

covered by this warranty. Unauthorized service or modification of the

product or of any furnished component will void this warranty in its entirety.

This warranty does not include reimbursement for inconvenience, instal-

lation, setup time, loss of use, or unauthorized service.

This warranty covers only DESA Specialty Products™ assembled prod-

ucts and is not extended to other equipment and components that a

customer uses in conjunction with our products.

THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRAN-

TIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY,

REPRESENTATION OR CONDITION OF MERCHANT ABILITY OR

THAT THE PRODUCTS ARE FIT FOR ANY PARTICULAR PURPOSE

OR USE, AND SPECIFICALLY IN LIEU OF ALL SPECIAL, INDIRECT,

INCIDENTAL, OR CONSEQUENTIAL DAMAGES.

REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE

CUSTOMER AND THERE SHALL BE NO LIABILITY ON THE PART OF

DESA SPECIALTY PRODUCTS™ FOR ANY SPECIAL, INDIRECT, INCI-

DENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT

LIMITED TO ANY LOSS OF BUSINESS OR PROFITS, WHETHER OR

NOT FORESEEABLE. Some states or provinces do not allow the exclusion

or limitation of incidental or consequential damages, so the above limitation

or exclusion may not apply to you. Retain receipt for warranty claims.

Page is loading ...

Heath Zenith SL-6171 User manual

This manual is also suitable for

Heath Zenith SL-6171 User manual

in other languages

Related papers

Other documents