Winston Products HBB5D2 Operating instructions

Brand: Winston Products

Model: HBB5D2

Type: Operating instructions

This manual is also suitable for

Includes all HBB0 and HBB5 Series Models

www.winstonind.com • 800-234-5286

HBB Series

Hold & Serve Drawers

Use & Care Manual

HBB0D1 HBB0D2 HBBON1

HBBON2 HBB5D1 HBB5D2

HBB5N1 HBB5N2

DOC050118I R18

cb_10-07-10

Built with pride by

HBB5D2

hold & serve drawer

www.winstonind.com • 800-234-5286

hold & serve drawer

Includes all HBB0 and HBB5 Series Models

Welcome ....................................... 2

Safety ........................................... 3

Receiving Your Appliance ............. 4

Electrical Information .................... 5

Ventilation Requirements ............. 6

Component Identification .............. 7

Controls ........................................ 8

Daily Operating Instructions ......... 9

Holding Reference Chart .............. 10

Holding Guidelines ....................... 11

Daily Cleaning .............................. 12-14

Troubleshooting ............................ 15-17

Circuit Diagram ............................. 18

ZAP Warranty ............................... 19

Terms & Conditions ...................... 20

Thank you for your purchase of a Winston

CVap

hold & serve drawer. The benefits you

will enjoy from this appliance include longer

hold times, better quality food, quicker

service, higher productivity, and safer food

temperatures.

This CVap hold & serve drawer utilizes

Controlled Vapor (CVap) technology. Using a

combination of dry and moist heat, CVap hold

& serve drawers keep foods hot and maintain

texture, whether moist or crisp, throughout

long serving periods. The two sets of

electronic differential control keys are easy to

understand and reliable. The controls never

need field calibration. The FOOD TEMP

Copyright© 2009 Winston Industries LLC. All rights reserved. CVap is a registered trademark of Winston Industries LLC. The CVap logo is a trademark of Winston Industries LLC. All other company and product names

may be trademarks of their respective companies.

Internet: www.winstonind.com

Email: CustomerService@winstonind.com

Phone: 800-234-5286•502-495-5400•Fax502-495-5458

Mail: 2345CartonDrive•Louisville,KY40299USA.

Need to contact us? Choose

the most convenient method.

keys allow precise control of food

temperature from 90 to 180˚F (32 to 82˚C).

The FOOD TEXTURE keys maintain just

cooked texture. Set texture near the Food

Temp for moist foods, or set higher for crisp

foods. Maximum cabinet temperature (Food

Temp plus Food Texture) is 250˚F (121˚C).

CVap hold & serve drawers are built with

durable stainless steel construction and full

insulation, and they are designed for high

volume usage.

If you have any questions, or if anything held

in your CVap hold & serve drawer doesn't

meet your satisfaction, please call our

Customer Service Center at 1-800-234-5286

or 502-495-5400, or email us at

[email protected].

table of contents

welcome

www.winstonind.com • 800-234-5286

hold & serve drawer

Includes all HBB0 and HBB5 Series Models

drawers or reaching into the appliance, as

heated vapor can quickly cause burns.

5. Clean appliance daily to prevent buildup of

food residue or chlorides, which can also

damage stainless steel and contaminate

food. Failure to follow proper cleaning

procedures can void your warranty.

6. Prior to using appliance for the first time,

perform the daily cleaning procedure

listed on pages 12 through 14.

7. Always allow appliance to cool before

cleaning, to avoid potential burns.

8. Do not place appliance in areas where air

temperature exceeds 100˚F (38˚C). A heat

shield may be required to prevent heat

exposure and grease laden vapors from

affecting the appliance if near heat, vapor,

or grease generating devices (such as grills,

steamers, ovens, etc.). Excess heat and

grease inside the appliance cavities may

cause electrical components to fail.

Please read this entire use & care manual

before operating your CVap

hold & serve

drawer. The manual contains important safety

information and operating instructions.

As is the case with many kitchen

appliances, your CVap hold & serve drawer

should be used with caution. Please read

the following warnings to avoid injuries.

1. Because this appliance utilizes high

voltage, it should only be installed and

serviced by a licensed electrician or

trained servicer. Attempting to install or

service the appliance yourself could result

in serious, potentially fatal injuries.

2. If an electrical shock is felt when touching

appliance, shut off power immediately

(either pull power cord or turn off circuit

breaker) and call a trained servicer for

repair. Failure to do so could result in

serious, potentially fatal injuries.

3 Always turn power switch off any time

appliance is not in use.

4. This appliance utilizes heated water vapor,

which transfers heat much more quickly

and efficiently than dry air of the same

temperature. Use caution when opening

Electrical Hazard

Can cause serious injury or death.

Do not attempt to install or service this appliance un-

less you are a licensed electrician or trained servicer.

Contamination Hazard

Can cause serious illness or damage to

appliance.

Clean appliance daily to avoid potential contamination

hazard.

Burn Hazard

Can cause injury.

Allow 30 minutes for appliance to cool before

attempting to clean.

High Temperature and Grease Hazard

Can cause damage to appliance.

Avoid placing appliance near high heat or in grease

laden atmosphere.

Burn Hazard

Can cause serious injury.

Avoid heated vapor when opening or closing

appliance drawer(s).

www.winstonind.com • 800-234-5286

hold & serve drawer

Includes all HBB0 and HBB5 Series Models

carrier should agree to inspect the damage

within 15 days. Please retain all packing

materials. The carrier will supply an

inspection report and the required claim

forms.

Water Supply

In order to operate properly, the evaporator in

this cabinet must be filled with clean, potable

water. As water evaporates, minerals in the

water will deposit on the surface of the

evaporator. These mineral deposits will inhibit

the transfer of heat. Deposits can also

degrade and damage stainless steel. To

avoid mineral deposits clean the appliance

daily. It is advisable to contact your water

utility for advice on minimizing deposit

buildup.

Shipping Damage

Examine equipment thoroughly for shipping

damage before, during and after unloading.

All Winston products are carefully inspected

and verified to be in good condition before

leaving our factory. The carrier delivering

your cabinet has assumed responsibility for

its safe arrival. If you notice any damage

(obvious or hidden), a claim must be made to

the carrier.

Obvious Loss or Damage

Please note any obvious loss or damage on

the freight bill or express receipt, and have

the carrier’s agent sign to acknowledge the

claim. The carrier will supply the necessary

forms. If you do not obtain and complete the

forms before the carrier's agent departs, the

carrier might refuse your damage claim.

Concealed Loss or Damage

Sometimes loss or damage is not obvious

until the product has been unpacked. If you

notice damage that was concealed by

packaging or crating, contact the carrier in

writing to notify them of the damage. The

receiving your appliance

Model Height with 1/2" Width Depth Weight

Feet (IN / MM) (IN / MM) (IN / MM) (LBS / KG)

HBB0D1 15.7/399 24.8/629 30.8/782 85/39

HBB0D2 25.5/648 24.8/629 30.8/782 115/52

HBB0N1 15.7/399 16.6/422 28.5/724 70/32

HBB0N2 25.5/648 16.6/422 28.5/724 101/46

HBB5D1 15.7/399 24.8/629 30.8/782 85/39

HBB5D2 25.5/648 24.8/629 30.8/782 115/52

HBB5N1 15.7/399 16.6/422 28.5/724 70/32

HBB5N2 25.5/648 16.6/422 28.5/724 101/46

High Temperature Hazard

Can cause damage to appliance.

Fill evaporator with water prior to turning power on,

and do not allow evaporator to run dry.

www.winstonind.com • 800-234-5286

hold & serve drawer

Includes all HBB0 and HBB5 Series Models

The appliance is shipped from the factory

with a 84" (213cm) minimum power cord and

plug. Refer to the table below to determine

the correct electrical outlet. It may be

necessary for a licensed electrician to install

the correct outlet or wiring. Winston does not

recommend wiring the appliance direct.

Below is electrical information for various

models of Winston’s CVap

hold & serve

drawers.

electrical

Model Volts Hertz PH Amps Watts Circuit Plug

Amp Type

HBB0D1 120 60 1 12.0 1440 US 15 /CAN 20 US 5-15P/CAN 5-20P

230 50 1 6.3 1440 N/A N/A

HBB0D2 120 60 1 12.0 1440 US 15 /CAN 20 US

5-15P/CAN 5-20P

230 50 1 6.3 1440 N/A N/A

HBB0N1 120 60 1 12.0 1440 US 15/CAN 20 US 5-15P/CAN 5-20P

230 50 1 6.3 1440 N/A N/A

HBB0N2 120 60 1 12.0 1440 US 15/CAN 20 US 5-15P/CAN 5-20P

230 50 1 6.3 1440 N/A N/A

HBB5D1 120 60 1 13.1 1572 US 15/CAN 20 US 5-15P/CAN 5-20P

230 50 1 6.8 1572 N/A N/A

HBB5D2 120 60 1 13.1 1572 US 15/CAN 20

US 5-15P/CAN 5-20P

230 50 1 6.8 1572 N/A N/A

HBB5N1 120 60 1 13.1 1572 US 15/CAN 20

US 5-15P/CAN 5-20P

230 50 1 6.8 1572 N/A N/A

HBB5N2 120 60 1 13.1 1572 US 15/CAN 20 US 5-15P/CAN 5-20P

230 50 1 6.8 1572 N/A N/A

INTERNATIONAL

www.winstonind.com • 800-234-5286

hold & serve drawer

Includes all HBB0 and HBB5 Series Models

Ventilation clearances - To operate properly,

the appliance will need sufficient space for air

circulation. Allow at least 2" (51mm)

clearance on all sides, particularly around

ventilation holes. Care should be taken to

prevent placing the appliance close to

anything combustible. It must be installed with

its supplied feet or legs. Counter top

appliances supplied without feet or legs may

be placed directly upon a counter top of non-

combustible material. In this situation, the

appliance may have to be sealed to the

counter top with a food-grade silicone sealant

(check local health codes). Appliances may

be stacked upon each other using only a

Winston supplied stacking kit and following

the instructions enclosed with the kit. Your

warranty may be void if you do not adhere to

these ventilation requirements.

ventilation requirements

Do not place appliance in an area where

ambient temperature (air temperature around

the appliance) exceeds 100°F (38˚C). A heat

shield may be required to prevent excessive

heat exposure and grease laden vapors from

affecting the appliance if adjacent to heat,

vapor, or grease generating devices (such as

grills, steamers, ovens, etc.). Excess heat

and grease inside the appliance cavities may

cause electrical components to fail.

Vent hood - Generally this appliance does

not need to be installed under a mechanical

ventilation system (vent hood). Check local

health and fire codes for requirements

specific to your location.

High Temperature and Grease Hazard

Can cause property damage.

Avoid placing appliance near high heat or in grease

laden atmosphere.

www.winstonind.com • 800-234-5286

hold & serve drawer

Includes all HBB0 and HBB5 Series Models

1. Name Plate (not visible in photo)

identifies model and serial numbers

(important for servicing and ordering

parts), voltage, power, and electrical

information. Electrical Requirements

Label identifies that appliance is for use

with an individual branch circuit only.

2. Drawer(s) 6" (152mm) deep for holding

one full size, two half size, or three third

size pans.

3. Food chamber - (not visible in photo)

holding cavity where the dual heat system

combines to create the perfect holding

environment.

4. Air Heaters (not visible) - Located inside

the base, supply heat for precise food

texture control.

5. Power Switch allows operator to turn

electrical power on and off.

6. Access panel provides easy access for

service.

7. Drawer Gasket(s) seals food chamber

against heat or vapor loss.

8. Evaporator (not visible in photo) located

inside the base, supplies vapor to food

chamber to control food temperature.

9. NEMA 5-15P Plug (US) and power cord

(not visible in photo) - Located on back

side, lower right-hand corner, provides

electricity to appliance. 5-20P plugs are

available for Canadian customers.

10. Control panel - contains power switch

and control escutcheon. Allows operator

to program food temperature and food

texture. Escutcheon is removable for

servicing or replacing microprocessor.

11. Drain Cap is removable for draining water

from evaporator.

12. Bottom cover (not visible in photo)

located underneath, allows service

access.

Wide 2-drawer

shown. Elements

are common to all

hold & serve

drawers.

component identification

www.winstonind.com • 800-234-5286

hold & serve drawer

Includes all HBB0 and HBB5 Series Models

1. Power Switch controls electrical power to

the appliance.

2. Digital LED Readout shows current

cabinet temperature(s). The default

temperature display is the temperature of

the water in the evaporator. To view

current air temperature, turn the Food

Texture dial up or down 5˚, then

immediately back to set temperature. The

Food Texture setting will display for five

seconds, then the display will show actual

air temperature. After five seconds the

default evaporator temperature will be

displayed.

3. Food Temp Keys control the temperature

of the water in the evaporator, which

directly controls the temperature of the

food being held. Allows food temperature

to be set in a range from 90 to 180˚F (32˚

to 82˚C).

4. F˚/C˚ Button is used to switch appliance

display between Centigrade and

Fahrenheit temperature scales.

On older models, simply press button to

switch from one mode to the other.

Newer models allow the operator to

program the default temperature display

scale. Pressing the ˚F/˚C key during

power up will toggle this scale.

During warm up this display will show the

changing Food Temp inside of the unit

until the selected temperature is achieved.

5. Food Texture Keys control the air

temperature within the food chamber,

which controls the rate of moisture

evaporation from the food. The “+”

temperature scale indicates the number of

degrees that the air temperature is

elevated above the Food Temp setting. A

texture setting at or near the food temp

setting will provide a moist texture.

Elevating the texture setting will deliver a

progressively drier and crisper texture. For

detailed guidelines on settings, see

information on pages 10 and 11.

controls

3 4 5

Some details have

been omitted for

clarity.

www.winstonind.com • 800-234-5286

hold & serve drawer

Includes all HBB0 and HBB5 Series Models

daily operating procedures

Prior to using appliance for the first time,

please perform the daily cleaning procedure

listed on pages 12 through 14.

Please make certain evaporator has an

adequate supply of water prior to turning on

power switch. Water level should be

approximately 1" (2.5 cm) from overflow.

1. Set appropriate food temperature using

the FOOD TEMP keys (set in accordance

with local health codes). Set desired

texture (from moist to crisp) using the

FOOD TEXTURE keys. See guidelines on

page 11 for specific settings.

2. Fill evaporator to within 1" (25mm) of

overflow with water.

NOTE: For locations with hard water, add

one tablespoon (15ml) of white vinegar or

lemon juice to water to help minimize

scale buildup. Please consider contacting

your local water authority to obtain advice

on possible water treatment to protect the

appliance. Some water supplies are high

enough in chemical content to be capable

of damaging stainless steel (if used

untreated). The evaporation process can

concentrate the chemicals in the water to

a level which could cause a damaging

reaction with the stainless steel.

3. Toggle Power Switch on. Allow 30

minutes for warm-up.

4. Insert food.

5. Adjust FOOD TEMP or FOOD TEXTURE

keys as needed to achieve desired food

quality.

KEEP DRAWER(S) CLOSED WHEN NOT IN

USE. If food temperature becomes too low

during serving period, increase

FOOD TEMP

setting by 10 to 20°F (11 to 17˚C) to maintain

desired food temperature.

High Temperature Hazard

Can cause damage to appliance.

Fill evaporator with water prior to turning power on,

and do not allow evaporator to run dry.

Contamination Hazard

Can cause serious illness.

Clean appliance prior to rst use, to remove traces of

industrial chemicals and oils.

www.winstonind.com • 800-234-5286

hold & serve drawer

Includes all HBB0 and HBB5 Series Models

Food Holding Reference Chart

Product Food Temp Food Texture

Very moist foods

Sauces, gravies, vegetables, etc. 140˚F (60˚C) +6˚F (3˚C)

Soft moist foods

Bakery, meats, fish, chicken, etc. 140˚F (60˚C) +10˚F (6˚C)

Firm moist foods

Finger foods, baked potatoes, etc. 140˚F (60˚C) +15-30˚F (8-17˚C)

Crisp dry foods

Crispy fried chicken, french fries, etc. 140˚F (60˚C) +50-60˚F (28-33˚C)

See Holding Guidelines Chart on page 12 for product recommendations with F/C settings.

NOTE:

1. The actual temperature of crisp dry foods may substantially exceed optimal

serving temperatures, making it necessary to reduce the FOOD TEMP setting as

much as 20-30˚F (11-17˚C) to obtain the desired temperature.

2. Total Food Texture (air temperature) setting equals the addition of the FOOD

TEMP and FOOD TEXTURE settings. For example, a FOOD TEMP setting of

140˚F (60˚C) and a FOOD TEXTURE setting of +10˚F (+6˚C) is equal to an

evaporator temperature of 140˚F (60˚C) and an air temperature of 150˚F (66˚C)

(140+10˚F (60+6˚C)).

www.winstonind.com • 800-234-5286

hold & serve drawer

Includes all HBB0 and HBB5 Series Models

Food

Temp

F°

PRODUCT

Food

Texture

F°

Food

Temp

C°

Food

Texture

C°

Food

Temp

F°

Food

Texture

F°

Food

Temp

C°

Food

Texture

C°

BREAD PRODUCTS

Biscuits 140-150 +20 60-66 +11

Rolls 140-150 +10 60-66 +5

Danishes 140-150 +10 60-66 +5

Croissants 140-150 +10 60-66 +5

White/Wheat Bread 140-150 +10 60-66 +5

French/Italian Bread 140-150 +15 60-66 +8

Pancakes/Waffles 140-150 +10 60-66 +5

French Toast 140-150 +10 60-66 +5

Fruit Pies 140-150 +15 60-66 +8

Gingerbreads 140-150 +15 60-66 +8

DAIRY & EGG

PRODUCTS

Eggs (Benedict, Fried,

Scrambled, Poached) 145-150 +5 62-66 +2

Omelets 150-160 +10 66-71 +5

Puddings/Custards 140-150 +5 60-66 +2

MEATS

Beef (Prime Rib,

Roasts, Steaks, BBQ) 130-140 +15 54-60 +8

Pork (Roasts, Chops,

BBQ, Bacon, Ham,

Sausage) 140-150 +15 60-66 +8

Lamb & Veal 140-150 +15 60-66 +8

Hamburger Patties 150-160 +10 66-71 +5

Hot Dogs 150-160 +10 66-71 +5

POULTRY

Chicken

Fried, Soft 150-160 +15 66-71 +8

Fried, Crisp 130-140 +50 54-60 +27

Roasted 150-160 +15 66-71 +8

BBQ 150-160 +15 66-71 +8

Turkey, Goose, Duck 150-160 +15 66-71 +8

SEAFOOD &

SHELLFISH

Fish, Fried 130-140 +50 54-60 +27

Fish, Broiled/Baked 150-160 +15 66-71 +8

Shrimp, Fried 130-140 +50 54-60 +27

Fish/Shrimp in

Sauce/Gravy 150-160 +5 66-71 +2

CELSIUS

FAHR EN HEIT

VEGETABLES

Vegetables,

Unbreaded

150-160 +5 66-71 +2

Vegetables, Breaded 130-140 +60 54-60 +33

Potatoes, Baked 150-160 +15 66-71 +8

STARCHES

Spaghetti 140-150 +5 60-66 +2

Rice 140-150 +5 60-66 +2

Lasagna 150-160 +10 66-71 +5

Beans 140-150 +15 60-66 +8

Soups & Sauces 140-150 +5 60-66 +2

Cooked Cereals 150-160 +10 66-71 +5

Casseroles 150-160 +5 66-71 +2

CRISP TEXTURED

FOODS

Pizza 130-140 +60 54-60 +33

Pastry Shells 130-140 +60 54-60 +33

Crisp Breadings 130-140 +60 54-60 +33

Crisp, Dry Foods 130-140 +60 54-60 +33

French Fries 100 +60 38 +33

PREPARED FOODS

Seafood in Sauce 150-160 +15 66-71 +8

Hamburgers in Buns 150-160 +10 66-71 +5

Cheeseburgers in Buns

150-160 +10 66-71 +5

Open Sandwich

w/Sauce/Gravy 150-160 +5 66-71 +2

Plated Foods 150-160 +5 66-71 +2

Entrees 140-150 +15 60-66 +8

Corn Dogs 140-150 +40 60-66 +22

PROOFING

Dough (Yeast Rolls,

Danish Dough) 100 +10 38 +5

Notes:

1. The recommendations in this chart should be regarded

as starting points. If user desires a more firm/dry

textured product, in crease the Food Tex ture set ting; for

a more soft/moist textured product, decrease the Food

Texture setting.

2. The holding time for very crisp foods may be less than

for other products.

3. Use a thermometer to assure com pli ance with local

health codes.

CELSIUS

FAHR EN HEIT

PRODUCT

holding guidelines - HBB series

www.winstonind.com • 800-234-5286

hold & serve drawer

Includes all HBB0 and HBB5 Series Models

Required Cleaning Accessories & Supplies

• Pan for draining evaporator

• Food grade germicidal detergent

• Descaling agent (ScaleKleen™)

(available through Winston Customer

Service 1-800-234-5286)

This appliance utilizes high voltage

electrical systems, high temperature

heating systems, and hot water vapor. If

used improperly, any of these hazards are

capable of causing serious injury or

death. To avoid the potential for an

accident, please have appliance installed

by a licensed electrician, and serviced

only by trained servicers. Please make

this page available to the servicer.

If an electrical shock is felt during

operation or cleaning, unplug appliance

and have it serviced before placing back

into service.

Ensure safe operation by cleaning

appliance daily. Failure to do so can allow

harmful deposits to develop, increasing

the potential for food contamination, and

endangering your customers.

daily cleaning

Clean evaporator daily to prevent chlorides

(salts) from accumulating. Chlorides can

cause the evaporator tank to corrode, to the

extent that leaks can occur. Leaks caused by

corrosion, which is caused by a failure to

clean daily, are not covered under the

manufacturer's warranty.

Prior to using appliance for the first time,

perform the daily cleaning procedure listed on

the following page.

Electrical Hazard

Can cause serious injury or death.

Disconnect appliance and contact licensed electrician

or trained servicer.

Contamination Hazard

Can cause serious illness.

Clean appliance prior to rst use, to remove traces of

industrial chemicals and oils.

Corrosion Hazard

Can cause damage to appliance.

Clean appliance daily to avoid potential corrosion

damage.

Contamination Hazard

Can cause serious illness or damage to

appliance.

Clean appliance daily to avoid potential contamination

hazard.

www.winstonind.com • 800-234-5286

hold & serve drawer

Includes all HBB0 and HBB5 Series Models

daily cleaning procedure

Before each cleaning procedure, disconnect

appliance from its electrical power source and

allow to cool for at least one half hour.

1. Place empty pan under drain cap, remove

cap and allow evaporator to drain.

2. Remove drawer(s) and wash using a food-

grade germicidal agent. Rinse and allow

to dry.

3. Spray food chamber and evaporator with

a food grade germicidal detergent.

NOTE: To ensure that drawer(s) opens and

closes easily, check drawer rollers (both

on the drawer and inside the appliance

cavity) to make sure they are tight, in

good operating condition, and not

excessively worn.

4. Wipe inside surfaces to remove all food

deposits.

5. Inspect for scale build-up on the tank

surface, water level sensor, and probe

(see photo below). If present, apply

descaling agent. Read ALL warnings and

follow directions listed on descaling agent

package.

6. Use pipe cleaner or spring to gently clean

out the trough drain hole (see photo

below). Be careful not to push too hard or

you may damage the plastic tube that

connects to the drain (not visible in photo).

If using a pipe cleaner, be sure to bend

the end back on itself so the sharp edge

of the wire is not exposed.

Burn Hazard

Can cause injury.

Allow 30 minutes for appliance to cool before

attempting to clean.

Leaking Hazard

Can cause damage to appliance.

Use care when cleaning plastic tube. Damage to tube

can cause leaking inside the appliance.

www.winstonind.com • 800-234-5286

hold & serve drawer

Includes all HBB0 and HBB5 Series Models

7. Inspect heating elements (if exposed).

The elements are stainless steel. If

cleaning is needed, scrub with Teflon

™

nylon bristle brush to remove heavy food

particles. Further cleaning may be done

with a plastic scouring pad and alkaline

based cleansers. DO NOT use wire

brushes, scrapers, steel wool pads or

chloride based cleansers. Follow cleanser

manufacturer's instructions for use on

stainless steel. Rinse well with clean water

and wipe immediately.

8. Rinse all inside surfaces, including

evaporator, and dry with clean towel.

Do not spray outside of appliance or

controls with water.

9. Replace drawer(s).

9. Verify O-ring is on drain pipe, replace

drain cap, and refill evaporator.

10. Reconnect appliance to electrical power

and make ready for use.

Electrical Hazard

Can cause serious personal injury or

damage to appliance.

Avoid spraying appliance exterior or controls with

water.

www.winstonind.com • 800-234-5286

hold & serve drawer

Includes all HBB0 and HBB5 Series Models

We know how frustrating and costly it can be

when a critical piece of equipment is down for

repairs. It is our goal to minimize service

disruptions, to get you back up and operating

in the shortest time possible.

We carefully analyze all service calls. This

analysis helps us to improve our

manufacturing processes, and reduces

product service issues. Generally speaking,

most equipment failures can be attributed to

the following three causes:

• Faulty use and care practices.

• Electrical supply problems.

• Equipment faults.

Please refer to the Troubleshooting Chart on

the next page for common problems and

solutions. If the problem you're experiencing

isn't listed, or if the standard solution fails to

troubleshooting

resolve your problem, you will need a

qualified servicer to diagnose and repair the

problem.

If your equipment is still under warranty, or

you are uncertain whether or not warranty is

still in place, please call Winston Customer

Service at 1-800-234-5286 (or

502-495-5400). Our friendly staff will help you

verify coverage, and if under warranty, will

arrange for a servicer to call on you.

If your equipment is no longer under warranty,

you can call our Customer Service line at

1-800-234-5286, or visit our website at www.

winstonind.com, and click the Service tab to

locate an authorized servicer near you.

In order to expedite service, please have the

complete model and serial number (found on

the appliance's identification tag) on hand

when you contact us.

Service parts may be purchased directly

from the factory online.

Visit www.winstonind.com

Please have the following information on hand when contacting Winston Industries

regarding product service.

1. Model _____________________Serial # _____________________________________

(located on name plate)

2. Your name ______________________________________________________________

3. Company name _________________________________________________________

4. Company address _______________________________________________________

_______________________________________________________________________

5. Company phone _________________________________________________________

6. Type of problem _________________________________________________________

_______________________________________________________________________

www.winstonind.com • 800-234-5286

hold & serve drawer

Includes all HBB0 and HBB5 Series Models

troubleshooting

FAULT CORRECTION

A. Circuit breaker tripped .............................................................................. Adjust

Fuse blown ............................................................................................... Replace

Power cord not plugged in ....................................................................... Plug in

Faulty cordset........................................................................................... Call servicer

Faulty power switch ................................................................................. Call servicer

B. Evaporator (water) tank empty................................................................. See page 10

C. Drain pipe o-ring defective or missing ..................................................... Replace

D. Food Temp setting too high ..................................................................... See page 10

E. Food Temp setting too low ....................................................................... See page 10

F. Food Texture setting too high .................................................................. See page 10

G. Food Texture setting too low .................................................................... See page 10

H. Drawer gasket defective .......................................................................... Replace

I. Drain cap defective or missing ................................................................. Replace

J. Faulty microprocessor controller .............................................................. Call servicer

K. Injury or accident, call manufacturer ........................................................ 1-800-234-5286

TROUBLE FAULT CODE

Digital display fails to light ................................................................................ A

Digital display reading inconsistently ............................................................... J

Flooding/leaking water ..................................................................................... C, H, I

Food drying out ................................................................................................ B, E, F, H

Food excessively moist .................................................................................... D, G

Food not hot enough ........................................................................................ E, G, H

Food too hot ..................................................................................................... D, F

Injury or accident .............................................................................................. J

www.winstonind.com • 800-234-5286

hold & serve drawer

Includes all HBB0 and HBB5 Series Models

This appliance utilizes high voltage

electrical systems, high temperature

heating systems, and hot water vapor. If

used improperly, any of these hazards are

capable of causing serious injury or

death. To avoid the potential for an

accident, please have appliance installed

by a licensed electrician, and serviced

only by trained servicers. Please make

this page available to the servicer.

SERVICE PARTS PART NUMBER

Bumper Feet PS2670-4

Bottom Assembly 01960V11

(for SS legs)

Bottom Assembly 01960W14

(for SS legs)

Control Board Assembly PS2822

(120V)

Control Board Assembly PS2870

(230, 240V)

Cover, Controls PS2882

Drain Cap PS1654

Drawer Assembly 07231U09

(before 9/29/06)

Drawer Assembly 07231AB16

(after 9/29/06)

Drawer Assembly 07231T08

Drawer Cover (Back) PS2213

Drawer Handle PS1393

Drawer Pan (6" deep) PS2209

Drawer, Tray Perforated PS2212

Evap Plug PS2878

Gasket, Drawer PS2253

Gasket, Drawer PS2195

Grommets PS1271-6

Heater, Air, 120V PS2697

(after 8/26/02)

840W,17.1 Ohms)

Heater, Air, 120V PS2705

(840W, 68.6 Ohms)

Heater, Air, 208-240V 05617AB114

(840W, 68.6 Ohms)

Heater, Air, 120V 05617Z81

(After 09/29/06)

(840W, 17.1 Ohms)

SERVICE PARTS PART NUMBER

Heater, Air, 208-240V 05617AB108

(840W, 68.5 Ohms)

Heater, Water, 120V PS2198

(Before 5/2/02)

(600W, 24 Ohms)

Heater, Water, 120V PS2698

(After 05/02/02)

(600W, 24 Ohms)

Heater, Water, 208V 05617X39

(600W, 72.1 Ohms)

Heater, Water, 120V PS2706

(600W, 24 Ohms)

Motor (120V) PS2196

Motor Asm w/ Fan (120V) PS2704

Motor (208-240V) PS23848

Motor Asm w/ Fan 06255AB112

(208-240V)

O-Ring, Drain Cap PS2180-3

O-Ring, Heater PS1784-3

Power Cord (120V) PS1595

Power Cord (120V) PS1548

Power Cord (240V) 04224Y37

Probe, Air PS2472

Probe, Water PS2440

Rail & Stud Assembly PS2227

Rollers PS2181-2

Switch, Power PS2304

Tank Asm PS2879

Thermostat, High Limit PS2730

Valve, Water PS2755

Water Level Sensor PS2593

troubleshooting

Electrical Hazard

Can cause serious injury or death.

Do not attempt to install or service appliance unless

you are a licensed electrician or trained servicer.

www.winstonind.com • 800-234-5286

hold & serve drawer

Includes all HBB0 and HBB5 Series Models

circuit diagram - HBB series

www.winstonind.com • 800-234-5286

hold & serve drawer

Includes all HBB0 and HBB5 Series Models

www.winstonind.com • 800-234-5286

hold & serve drawer

ZAP WARRANTY AGREEMENT

This warranty agreement applies to commercial equipment, equipment service parts, and safety parts (collectively, “products") manufactured by

Winston Industries, LLC (“Winston") and its corporate predecessors and is extended to any purchaser, lessee or successor purchaser (“purchaser").

NEW EQUIPMENT

Any part of a new appliance, except gaskets, hoses, lamps, power cords, fryer baskets, glass panels, and evaporators which proves to be

defective in material or workmanship within one (1) year from the date of delivery to original end-user purchaser or 18 months from the date of

manufacture, whichever comes rst, will be repaired or replaced (at Winston’s option) free of charge.

REPLACEMENT PARTS

Any appliance replacement part except gaskets, hoses, lamps, power cords, fryer baskets, glass panels, batteries, and evaporators which proves

to be defective in material or workmanship within one (1) year from the date of original installation will be repaired or replaced free of charge.

LABOR, TRAVEL, TRANSPORTATION

The warranty for new equipment covers the repair or replacement (at Winston’s option) of the defective part(s), delivery of the replacement part(s),

labor charges for the removal and installation of replacement part(s) for one (1) year from the start of the warranty period. This warranty includes

travel time not to exceed two hours and mileage not to exceed 50 miles (100 miles round trip).

The warranty for replacement parts covers the repair or replacement (at Winston’s option) of the defective part(s) and does not include any labor

charges for the removal and installation of any part(s), travel, transportation or other expenses incidental to the repair or replacement of part(s).

The warranty does not cover: gaskets, hoses, lamps, power cords, fryer baskets, glass panels, supplies, evaporators, supply items (including but

not limited to: gaskets, brushes, lter paper, cleansers, etc.), software, corrosion of stainless steel, normal maintenance, lubrication, cleaning or

descaling, programming or adjusting temperatures, calibration, tightening of fasteners or plumbing connections, appliances with removed or altered

identication tags, damage resulting from delivery of the appliance, customer mishandling or abuse, or no problem found.

THE USE OF POOR QUALITY WATER WILL VOID PRODUCT WARRANTIES. See Product Use and Care Manual for water quality

recommendations.

PROPER INSTALLATION IS THE RESPONSIBILITY OF THE PURCHASER, AND IS NOT COVERED BY THIS WARRANTY. PRODUCTS MUST

NOT BE INSTALLED IN LOCATIONS EXPOSING THEM TO EXCESSIVE HEAT SOURCES, AMBIENT TEMPERATURES ABOVE 100°F, OR

CONTAMINATES DETRIMENTAL TO THE APPLIANCE COMPONENTS (SUCH AS CAUSTIC SOLUTIONS, HIGH MOISTURE, WATER OR

GREASE LADEN VAPORS NEAR ELECTRONIC COMPONENTS, ETC.).

As a condition to the application of this warranty, purchaser will operate, clean and maintain products in accordance with use and care instructions,

warnings, manuals and any other notices and/or instructions from Winston which may be with or on products or sent separately; will notify Winston

of resale, removal or retirement of products; will notify Winston immediately of any accident or injury arising out of use of products and cooperate

with Winston in the investigation of any such accident or injury; will maintain registration with Winston of location and serial number of products

while in purchaser’s control and use; will require all personnel operating products to become thoroughly familiar with use and care instructions

and all other notices and/or instructions before such personnel operate products; will thoroughly train all personnel operating products to follow all

instructions contained on or in all safety labels and use and care instructions; will immediately afx safety labels and put into use the use and care

instructions; will immediately use, according to instructions, safety parts supplied by Winston; will install equipment service parts in accordance

with Winston’s written instructions; will utilize only Winston manufactured replacement parts and make no changes or alterations to products, ex-

cept as approved or instructed in writing by Winston; and will when requested by Winston, cooperate with Winston in the prevention of injuries from

purchaser’s use of products.

PURCHASER’S SOLE AND EXCLUSIVE REMEDY AGAINST WINSTON SHALL BE FOR THE REPAIR OR REPLACEMENT OF DEFECTIVE

PARTS AS PROVIDED HEREIN. THE TOTAL LIABILITY OF WINSTON WITH RESPECT TO ITS PRODUCTS, WHETHER UNDER WARRANTY

OR OTHERWISE, SHALL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCTS AND THE LABOR AND TRAVEL TO REPLACE THE

PRODUCTS OR ANY PART THEREOF. WINSTON SHALL NOT BE LIABLE TO THE PURCHASER OR OTHERS FOR ANY DIRECT, INDIRECT,

SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSS OF PROFITS RESULTING FROM ANY CAUSE WHATSOEVER,

INCLUDING BUT NOT LIMITED TO, DEFECTIVE WORKMANSHIP, MATERIALS OR ANY ERROR OR OMISSION OF WINSTON.

WINSTON EXPRESSLY DISCLAIMS ALL OTHER WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE AND ANY IMPLIED WARRANTY OF MERCHANTABILITY.

For warranty inquiries and customer specic warranties, call Winston Customer Service at 1-800-234-5286 or 502-495-5400.

4272V089 Rev 8

11/05/09

Prices subject to change without notice.

F.O.B. Louisville, KY, USA

(800) 234-5286 or (502) 495-5400 Fax (502) 495-5458

www.winstonind.com

All sales subject to Company’s Terms and Conditions

Winston Products Company

2345 Carton Drive

Louisville, KY 40299

ZAP zero accidents program

Includes all HBB0 and HBB5 Series Models

www.winstonind.com • 800-234-5286

Prices subject to change without notice.

F.O.B. Louisville, KY, USA

(800) 234-5286 or (502) 495-5400 Fax (502) 495-5458

www.winstonind.com

All sales subject to Company’s Terms and Conditions

Winston Products Company

2345 Carton Drive

Louisville, KY 40299

TERMS AND CONDITIONS OF SALE

In consideration of the mutual benefits hereby to be derived, Winston Industries, LLC (“Winston”) and any purchaser, lessee or successive purchaser ("Purchaser"), of Winston

Commercial Equipment, Equipment Service Parts, and Safety Parts (collectively “Products”) agree that:

1. Terms of sale for Products are net 25 (payment must be received within 25 days from invoice date). Prices are subject to change without notice. Purchaser agrees to pay all costs

of collection of past due accounts, including reasonable attorney’s fees. All claims must be made within five (5) days of receipt of goods or claim will not be allowed. All goods are

shipped at Purchaser’s risk. Confirmed orders may not be cancelled or delayed without written permission from Winston. Cancelled or delayed orders may be subject to a 20%

inventory adjustment/warehousing fee. Delayed orders will be invoiced on the confirmed ship date. Products may not be returned without written permission from Winston as

described in paragraph #6 below. Orders placed prior to a price increase, which are due to ship after the increase, may be charged at the new price.

2. An order will not be effective until accepted by an authorized representative at Winston's home office. Unless otherwise specified in writing (a) delivery will be made F.O.B.

Louisville, Kentucky and risk of loss or damage shall pass to Purchaser upon delivery to the carrier, and (b) the method or agency of transportation and routing will be selected by

Winston. Winston reserves the right to ship freight collect.

3. Winston shall not be liable for any delay in performance due to fire, explosion, casualty, strike or other labor difficulties, shortage of utility facility, delay to transportation,

breakdown or accident, compliance with other action to carry out the intent or purpose of any law or regulation, or any cause, whether similar or dissimilar, beyond Winston’s

reasonable control and Winston shall have such additional time for performance as may be reasonably necessary under the circumstances and the right to apportion its production

among its customers in such a manner as it may deem equitable.

4. Purchaser agrees to indemnify and hold Winston harmless from any loss, cost or expense, including cost of defense, and reasonable attorney’s fees, incurred by Winston, arising

from or related to (1) Purchaser’s use or sale of Products, including, but not limited to, Purchaser’s failure to warn Purchaser’s workers and others of hazards involving the Products;

Purchaser’s failure to provide copy of Terms and Conditions at time of sale of Products to others; Purchaser’s failure to instruct Purchaser’s workers and others in how to safely use

the Products in compliance with the Use and Care Manual; and Purchaser’s failure to provide safe working conditions and proper safety clothing and gear with respect to the

Products, and (2) non-compliance with these Terms and Conditions, or both.

5. Purchaser shall pay, in addition to the price hereunder, as a separate item, any taxes which Winston may be required to pay or collect under existing or future laws with respect to

the sale, delivery, transportation, or use of any Product sold hereunder including all taxes, however designated, upon or measured by amounts paid to Winston by Purchaser

hereunder, except net income tax.

6. Products may not be returned by Purchaser except by prior written agreement with Winston. Returns without prior authorization, as indicated by an RA number applied to the

returned packaging, will be refused. All returned Products are subject to inspection by Winston and a 20% restocking charge ($30 minimum), which may be reduced if replacement

Product is ordered, plus any other costs necessary to restore the Products to new condition. The Products must be returned to the Winston factory freight prepaid, in new condition,

and in the original packaging. Winston reserves the sole right to determine the amount of credit to be issued on any Products returned for credit. Only standard, currently

manufactured Winston Products may be considered for return and credit. No returns will be accepted on modified or special order Products (built to a Purchaser’s specifications),

used Products, or on Products older than 90 days from the original date of shipment.

7. Acceptance is expressly limited to the Terms and Conditions set forth herein and any additional or different terms proposed by Purchaser are rejected unless expressly assented

to in writing. In the event during the course of dealing, Winston signs or otherwise accepts any documents or forms submitted by Purchaser containing any Terms or Conditions

contrary to or in addition to those of Winston set forth herein, such documents and forms shall be deemed to have been used for the mere convenience of Purchaser in the conduct

of its internal business affairs and not for the purpose of varying the Terms and Conditions of this order. This order including these Terms and Conditions shall constitute entirely the

Terms and Conditions between the parties with respect to the transaction covered hereby and to all subsequent transactions for Products obtained from Winston, and no waiver,

alteration or modification shall be binding on Winston unless in writing and signed by an authorized officer of Winston at its home office.

8. Purchaser's sole warranty is the Zero Accident Program (ZAP) Warranty Agreement on products manufactured by Winston in effect at the time of the sale.

OTHER THAN THE ZAP WARRANTY AGREEMENT, WINSTON MAKES NO WARRANTY OF ANY KIND WHATSOEVER, EXPRESS OR IMPLIED, CONCERNING THE

PRODUCTS. WINSTON EXPRESSLY EXCLUDES ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE TOTAL LIABILITY

OF WINSTON WITH RESPECT TO ANY PRODUCT SHALL IN NO EVENT EXCEED THE PURCHASE PRICE THEREOF, AND LABOR TO REPLACE. WINSTON SHALL IN NO

EVENT BE LIABLE TO PURCHASER OR OTHERS FOR ANY DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OR LOSS OF PROFITS

RESULTING FROM ANY CAUSE WHATSOEVER, INCLUDING, BUT NOT LIMITED TO, DEFECTIVE WORKMANSHIP, MATERIALS OR ANY ERROR OR OMISSION OF

WINSTON.

9. Winston shall not be liable for claims of patent infringement against Purchaser or Purchaser's loss of the right to use the Product.

10. ARBITRATION: Any controversy or claim arising out of or relating to this Order, or the breach thereof, shall be settled by binding arbitration in accordance with the Commercial

Arbitration Rules of the American Arbitration Association, except that any arbitration hearing shall be held in Louisville, Kentucky. Judgment upon the award rendered by the

arbitrator(s) may be entered in any court having jurisdiction thereof. Any application for review of an arbitration award shall be allowed only to the extent required by Kentucky law

and shall be brought in an appropriate court in the Thirteenth Judicial Circuit or District of Kentucky, or in the United States District Court for the Western District of Kentucky.

11. GOVERNING LAW: This Order and the rights, duties and legal relations of the parties, and any arbitration are governed by and construed under Kentucky laws.

12. The products sold hereunder are produced in compliance with the Fair Labor Standards Act.

4272X833 rev10 2/9/05

terms & conditions

hold & serve drawer