Generation Lighting 44626BLE-782 Installation guide

Type
Installation guide

This manual is also suitable for

Carefully remove the fixture from the carton and check that all parts
are included, as shown in figure 1 and 2. Be careful not to misplace
any of the screws or parts which are needed to install this fixture.
*OUTLET
BOX
FIGURE 1 *NOT INCLUDED
UNIVERSAL
MOUNTING
PLATE (D)
NUT (E)
NIPPLE (F)
GREEN
GROUNDING
SCREW (G)
FIXTURE
GROUND
WIRE (H)
Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
If you are unclear as to how to proceed, contact a qualified electrician.
You don't need special tools to install this fixture.
Be sure to follow the steps in the order given.
Under no circumstances should a fixture be hung on house
electrical wires, nor should a swag type fixture be installed on a
ceiling which contains a radiant type heating system.
Read instructions carefully.
Save these instructions.
Installation And Safety Instructions
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to
this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
HC-1577
0
90909
IMPORTANT SAFETY INSTRUCTIONS
BEFORE YOU BEGIN
T
o clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
K
eep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when
ordering parts.
CLEANING
ORDERING PARTS
Thread nut (E) on to nipple (F) so five threads are exposed past nut
(E). Thread this end of nipple (F) into universal mounting plate (D),
and tighten nut (E) to secure.
Using outlet box screws (not supplied) fasten universal mounting
plate (D) to outlet box through slots in universal mounting plate (D).
STEP 1:
STEP 2:
INSTALLATION
*OUTLET BOX
SCREWS
*HOUSE
GROUND
WIRE
STEP 1
STEP 2
STEP 4
GROUNDING INSTRUCTIONS
:
Connect the supply ground wire, fixture ground wire, and mounting bar
ground wire (pre attached) using the supplied wiring connector. Gently try
to remove the wires from the connector. If you can remove the wires,
carefully re-do the wiring connection.
INSTALLATION (continued) HC-1577
STEP 3:
A
.
U
se a listed wire connector to connect the fixture hot wire (black
wire, or round and smooth tracer) to the supply hot wire.
B. Use a listed wire connector to connect the fixture common wire
(white wire, or square and rigid) to the supply common wire.
C
.
G
ently try to remove the wires from the connector. If you can
remove the wires, carefully re-do the wiring connection.
STEP 4:
M
ake sure no bare wires can be seen outside wire connectors. After
wires are connected, tuck them carefully inside outlet box. Push the
fixture firmly over the nipple (F) and against the wall. Secure canopy
(I) in place by threading cap nut (J) onto nipple (F).
Make sure no bare wires can be seen outside wire connectors.
Install self ballasted lamps (K) by gently twisting into socket (L).
P
lace shade (A) on socket cup (B) and secure by threading retaining
ring (C) onto socket (C).
FINAL ASSEMBLY
STEP 5:
STEP 6:
STEP 7:
*NOT INCLUDED
NUT (E)
SHADE (A) RETAINING
RING (C)
NIPPLE (F)
GREEN
GROUNDING
SCREW (G)
FIXTURE
GROUND
WIRE (H)
*WIRE
CONNECTORS
SOCKET
CUP (B)
*HOUSE
GROUND
WIRE
CANOPY (I)
CAP
NUT (J)
STEP 6
STEP 3
STEP 5
Hg
MARK MEANS LAMP CONTAINS MERCURY.
FOLLOW DISPOSAL LAWS.
SEE WWW.LAMPRECYCLE.ORG
FIGURE 2
FIXTURES WITH A ONE PIECE
LAMP / BALLAST COMBINATION
SELF BALLASTED
LAMP (K)
SOCKET (L)
STEP 7
FIGURE 3
  • Page 1 1
  • Page 2 2

Generation Lighting 44626BLE-782 Installation guide

Type
Installation guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI